Hi again guys, i have a BIG! problem i tried every method to fix it but with no result so this is what happend my phone got in a bootloop after flashing the wrong cwm and then i decided to fix it with Alcatel Software Upgrade Tool so i fixed it after the boot i seen my IMEI is INVALID how to fix it ? Engineering mode gives me an error ,,AT command failed to send'' the other methods dont work too .. can i do something to fix it ? (phone: Alcatel OT Pop C5 [5036D] ) my baseband is ok and the radio_state shows off in the engineering mode
Hi, Thanks for using XDA assist
It looks like there is no dedicated forum for your device, however
There is a general forum for android here http://forum.xda-developers.com/android/help where you can try to ask to get expert's help.
Good luck.
Related
Hi guys am using a huawei u8651t and i tried flashing CWM on it after it completed ,it did reboot into T-mobile logo
screen then all of a sudden it starts to change in different colors and then turns into a dark screen with no commands , I would really appreciate it if any of you guys could help fix the problem
Hi,
I could only find very old threads on your device, with likely outdated information. I would try asking for help here...
http://forum.xda-developers.com/showthread.php?t=2257421
Good luck!
Hi, I've brought my dead gionee back to life but i got some problems with IMEI's and SIM cards, and Finally decided to flash a different ROM with higher micromax version. (From micromax 25 to 52)
Now, my phone does not work and the new operation system is unable to load after powring on the phone which shows a black screen, with LED backlight on the keyboard.
I would have flashed the phone to recover it back but the sp flash tool gives brom error
"BROM ERROR: S_BROM_CMD_STARTCMD_FAIL (2005) [BROM] Can not pass bootrom start command! Possibly target power up too early"
I did a long research on google but couldn't find a working solution. So, I hope you give me link to an equivalent flashing tool or maybe you can help me solve the brom issue.
Device: gionee pioneer p1
Thank you.
FinnTheHuman. said:
Hi, I've brought my dead gionee back to life but i got some problems with IMEI's and SIM cards, and Finally decided to flash a different ROM with higher micromax version in vain. (From micromax 25 to 52)
Now, my phone does not work and the new operation system is unable to load after powring on the phone which shows a black screen, with LED backlight on the keyboard.
I would have flashed the phone to recover it back but the sp flash tool gives brom error
"BROM ERROR: S_BROM_CMD_STARTCMD_FAIL (2005) [BROM] Can not pass bootrom start command! Possibly target power up too early"
I did a long research on google but couldn't find a working solution. So, I hope you give me link to an equivalent flashing tool or maybe you can help me solve the brom issue.
Device: gionee pioneer p1
Thank you.
Click to expand...
Click to collapse
Hello, and thank you for using XDA Assist!
Sounds like your EFS got borked a while back. No flashing of ROMs will fix that unfortunately...I would try to get it back as much to stock as possible for warranty/service work.
Since I only see rooting threads about your device, you can ask for advice here:
> Android Development and Hacking > Android Q&A, Help & Troubleshooting > [Ask Any Question][Newbie Friendly]
Hope this helps, and good luck!
OfficerJimLahey said:
Hello, and thank you for using XDA Assist!
Sounds like your EFS got borked a while back. No flashing of ROMs will fix that unfortunately...I would try to get it back as much to stock as possible for warranty/service work.
Since I only see rooting threads about your device, you can ask for advice here:
> Android Development and Hacking > Android Q&A, Help & Troubleshooting > [Ask Any Question][Newbie Friendly]
Hope this helps, and good luck!
Click to expand...
Click to collapse
I didn't back up the EFS stuff at first place, that's why I think it's a permanant issue. In fact, I would have done a full backup after I had rooted the device but, unfortunately, it seemed that NANDroid, CMW and such custom recoveries were not compatible with it.
Thanks anyway. you did a good job
Hello,
I'm new to the forum. I decided to register, because here is the biggest base of android knowledge.
I need your help about my phone Landvo L500s. I tried to install custom rom-cyanogenmod 12 on it and eventually I bricked the phone. I have tried all the ways shown in internet tutorials to unbrick phone with factory rom, but I always get this error-BROM ERROR: S_FT_ENABLE_DRAM_FAIL (4032); [EMI] Enable DRAM Failed!
I have already installed USB VCOM drivers and my phone is recognised by device manager(Windows 8.1 x64) so that's not the cause.
Also I can't access recovery mode, as phone doesn't start any more.
If you know any solution, Please help me solve the problem.
Hi,
Thanks for using XDA assist.
I couldn't find a thread that could help you unbrick your device.
Please create a XDA account and post in the following forum:
Android Q&A, Help & Troubleshooting
Good Luck! - gsstudios
Already solved it!
I already solved the problem. I found more stable Stock ROM and flashed it...
I was trying to flash my canvas 2.2 a114 and accidentally flashed a wrong scatter file.
Now my phone is getting detected in sptools, but it doesnt get on, no charging led, no recovery mode, no sign of working.
It gets format successfully but download is always interupted by some error, either NO_PARTITION / PMT ERROR / NO_SPACE(5069)
I have searched almost all the threads on google and xda forum, but still unable to get out of it.
Guide me through this as soon as possible.
abhishek.12415 said:
I was trying to flash my canvas 2.2 a114 and accidentally flashed a wrong scatter file.
Now my phone is getting detected in sptools, but it doesnt get on, no charging led, no recovery mode, no sign of working.
It gets format successfully but download is always interupted by some error, either NO_PARTITION / PMT ERROR / NO_SPACE(5069)
I have searched almost all the threads on google and xda forum, but still unable to get out of it.
Guide me through this as soon as possible.
Click to expand...
Click to collapse
Hi abhishek.12415
Thank you for using XDA Assist
As we do not have an specific forum dedicated to your device yet, our experts at the below forum should be able to help you. Please be welcome to ask in there.
Android Q&A, Help & Troubleshooting
Nice regards and good luck.
.
Hi Guys,
Tried looking for a similiar issue, didnt find any on XDA, there are some on the internet but non with a solution.
Without any custom roms or recoveries, my tablet just got stuck at the wellcome screen. I cant get into recovery. I can get the preloader detected and i also can capture the tablet in SP Flash tools, but any step attempted ends with an error.
I found a firmware file for this tablet at a russian page https://yadi.sk/d/_CsVJm3YejLq7 , but it doesnt work either. So no "Download" no "Format" and no "Upgrade firmware" option works. I can also provide the error codes if needed.
Any idea how to fix this?
Thanks and regards
G.
Hello,
Welcome to XDA.
There is no forum for your device. Try posting your question in the forum linked below.
http://forum.xda-developers.com/android/help
The experts there may be able to help. Good luck.