I've decided to open this thread for development md mmx ninja a45 .
Rom dump :
http://www.mediafire.com/?gla8fgpwl0r0hvf
ROOTING (credits:rishu)
pre requisites *a45 drivers and *superoneclick
firstly dissable ur antivirus...
1)download drivers available at micromax's site
2)Connect your device on your PC and be sure that USB Debugging is enabled.
Your PC will ask on how will you install the driver, choose “Install from a specific location” then navigate to where you had downloaded earlier.
3)After drivers has been already installed, open super one click.
4)Click the “Root” button.
Then rooting will start automatically....
Installing CWM: (credits antonysabish)
Micromax A45 Clockworkmod
Recovery
Here's how to get Clockworkmod recovery
with SP Flash Tool:
1. Download SP Flash Tool.
2. Download MT6573_Android_scatter.txt.
3. Download a45recovery-cwm.zip and extract it.
4. Extract SPF Tool.zip and Run
Flash_tool.exe from there.
5. Click File->Open Scatter-loading file and
select the MT6573_Android_scatter.txt you
downloaded.
6. Now uncheck everything except
RECOVERY . Click on recovery and select
a45recovery-cwm.img you downloaded.
7. Now turn off your Micromax A45,
remove battery and put it back( DONT
switch it back on).
8. Press Download in the SP Flash Tool
window, then When the countdown starts,
connect your phone to PC.
9. After it's done, disconnect the phone,
remove battery and put it back. Boot the
phone into Recovery mode, You should
have Clockworkmod v5.8.1.9
download super one click : http://205.196.120.108/ll71hms5t67g/l291ej5damzoujk/SuperOneClickv2.3.3-ShortFuse.rar
Anyone interested please join
Procedure:
1. Download and install drivers Driver_Auto_Installer_v1.1236.00.7z.
If not working try these too PDAnet_4150.rar.
Problem in installation?? Go here
2. Download scatter from here .
3. Open SP flash tools, load scatter in sp flash tools and go to read back tab. (alternative download link of sp flash tools)
4. Click 'Add' and tap on added read back entry.
5. Select any path to save file and click ok, write 0x3E180000 in length and click ok.
6. Click on read back and connect phone without battery. Wait till it completes.
7. Once you see a green circle, close sp flash tools and switch on the phone.
8. When the phone is on, connect it to pc. See if any notification of 'usb debugging' comes in phone, if not, go to settings->about phone->and tap build number 7 times to enable debugging options.
9. Go back and enter developers options(in settings), and check usb debugging on.
10. Now run mtk driod tools and it will detect phone. (alternative download link of mtk droid tools)
11. In mtk droid tools, click 'root, backup and recovery' tab.
12. Click 'To process file ROM_ from Flash Tool.
13. Locate the file you got from read back.
14. Say no to make CWM recovery automatically and cancel to choose a recovery for similar phone.
15. Now wait again.
Once done, you will get your sp flashable backup in MTK Driod Tools/backup.
Read back complete.
Now follow this guide to root your Unite 2.
Sudeep Duhoon said:
Procedure:
1. Download and install MTK VCOM drivers.
Problem in installation?? Go here
2. Open SP flash tools and go to read back tab. (alternative download link of sp flash tools)
3. Click 'Add' and tap on added read back entry.
4. Select any path to save file and click ok, write 0x3E180000 in length and click ok.
5. Click on read back and connect phone without battery. Wait till it completes.
6. Once you see a green circle, close sp flash tools and switch on the phone.
7. When the phone is on, connect it to pc. See if any notification of 'usb debugging' comes in phone, if not, go to settings->about phone->and tap build number 7 times to enable debugging options.
8. Go back and enter developers options(in settings), and check usb debugging on.
9. Now run mtk driod tools and it will detect phone. (alternative download link of mtk droid tools)
10. In mtk droid tools, click 'root, backup and recovery' tab.
11. Click 'To process file ROM_ from Flash Tool.
12. Locate the file you got from read back.
13. Say no to make CWM recovery automatically and cancel to choose a recovery for similar phone.
14. Now wait again.
Once done, you will get your sp flashable backup in MTK Driod Tools/backup.
Read back complete.
Now follow this guide to root your Unite 2.
Click to expand...
Click to collapse
1) we have to load scatter file first right?
2) how huch time it takes to readback?
codergenius said:
1) we have to load scatter file first right?
2) how huch time it takes to readback?
Click to expand...
Click to collapse
Oops, sry. That was added from day one in my pc so forgot.
Added scatter now.
About 5 mins.
anyone using win 7 pro 64 bit : able to install vcom drivers & successfully rooted unite 2 (i am unable to readback using sp flash tools...getting error as "USBSetting::SearchUSBPortPool(): Scaning USB port failed!(..\QT_FlashTool_Refactor\Conn\USBSetting.cpp,195)" in QT_FLASH_TOOL.log and error "IsValidCOMPort(): Instance ID(USB\VID_8086&PID_0189\6&1279F1F3&0&5) (FlashToolLib/host/windows/com_enum.cpp:942)" in BROM_DLL_V5.log while read back, i am not sure if it is driver issue as preloader driver gets successfully installed
green circle
Sudeep Duhoon said:
Procedure:
1. Download and install drivers Driver_Auto_Installer_v1.1236.00.7z.
If not working try these too PDAnet_4150.rar.
Problem in installation?? Go here
2. Download scatter from here .
3. Open SP flash tools, load scatter in sp flash tools and go to read back tab. (alternative download link of sp flash tools)
4. Click 'Add' and tap on added read back entry.
5. Select any path to save file and click ok, write 0x3E180000 in length and click ok.
6. Click on read back and connect phone without battery. Wait till it completes.
7. Once you see a green circle, close sp flash tools and switch on the phone.
8. When the phone is on, connect it to pc. See if any notification of 'usb debugging' comes in phone, if not, go to settings->about phone->and tap build number 7 times to enable debugging options.
9. Go back and enter developers options(in settings), and check usb debugging on.
10. Now run mtk driod tools and it will detect phone. (alternative download link of mtk droid tools)
11. In mtk droid tools, click 'root, backup and recovery' tab.
12. Click 'To process file ROM_ from Flash Tool.
13. Locate the file you got from read back.
14. Say no to make CWM recovery automatically and cancel to choose a recovery for similar phone.
15. Now wait again.
Once done, you will get your sp flashable backup in MTK Driod Tools/backup.
Read back complete.
Now follow this guide to root your Unite 2.[/
What do you mean by green circle? I can't see except that stop button, which is already green.
Click to expand...
Click to collapse
Green circle
Zao, it worked for me after putting in the battery. The flash_tools hanged for a minute then automatically started backing up.
Regards,
Abhishek
MTK specific apps
Hi,
Can you confirm if the rom is 4.4.2.
If it is 4.4.2 ROM, then can you please extract and provide the mtk specific apks from /system/app,
ie;
EngineerMode,
EngineerCode
EngineerModeSIM
Mkt_boot
MTKAndroidSuiteDeamon
MTkBT
MTKLogger
MTKThermalManager
YGPS
Thanks in advance.
Or can you provide me the link to download KitKat rom
Sudeep Duhoon said:
Procedure:
1. Download and install drivers Driver_Auto_Installer_v1.1236.00.7z.
If not working try these too PDAnet_4150.rar.
Problem in installation?? Go here
2. Download scatter from here .
3. Open SP flash tools, load scatter in sp flash tools and go to read back tab. (alternative download link of sp flash tools)
4. Click 'Add' and tap on added read back entry.
5. Select any path to save file and click ok, write 0x3E180000 in length and click ok.
6. Click on read back and connect phone without battery. Wait till it completes.
7. Once you see a green circle, close sp flash tools and switch on the phone.
8. When the phone is on, connect it to pc. See if any notification of 'usb debugging' comes in phone, if not, go to settings->about phone->and tap build number 7 times to enable debugging options.
9. Go back and enter developers options(in settings), and check usb debugging on.
10. Now run mtk driod tools and it will detect phone. (alternative download link of mtk droid tools)
11. In mtk droid tools, click 'root, backup and recovery' tab.
12. Click 'To process file ROM_ from Flash Tool.
13. Locate the file you got from read back.
14. Say no to make CWM recovery automatically and cancel to choose a recovery for similar phone.
15. Now wait again.
Once done, you will get your sp flashable backup in MTK Driod Tools/backup.
Read back complete.
Now follow this guide to root your Unite 2.
Click to expand...
Click to collapse
i am facing some problem with preloader.....please guide me through.........
kanishka singh said:
i am facing some problem with preloader.....please guide me through.........
Click to expand...
Click to collapse
What problem? Explain a bit.
eagledipesh said:
Hi,
Can you confirm if the rom is 4.4.2.
If it is 4.4.2 ROM, then can you please extract and provide the mtk specific apks from /system/app,
ie;
EngineerMode,
EngineerCode
EngineerModeSIM
Mkt_boot
MTKAndroidSuiteDeamon
MTkBT
MTKLogger
MTKThermalManager
YGPS
Thanks in advance.
Or can you provide me the link to download KitKat rom
Click to expand...
Click to collapse
Here is the stock rom. Yes it is kitkat.
http://support.moulnisky.com/index.php?dir=Micromax/
zao.remy said:
Sudeep Duhoon said:
Procedure:
1. Download and install drivers Driver_Auto_Installer_v1.1236.00.7z.
If not working try these too PDAnet_4150.rar.........................Once done, you will get your sp flashable backup in MTK Driod Tools/backup.
Read back complete.
Now follow this guide to root your Unite 2.[/
What do you mean by green circle? I can't see except that stop button, which is already green.
Click to expand...
Click to collapse
A pop up will come when it will finish. On center of the sp flash tools.
codergenius said:
anyone using win 7 pro 64 bit : able to install vcom drivers & successfully rooted unite 2 (i am unable to readback using sp flash tools...getting error as "USBSetting::SearchUSBPortPool(): Scaning USB port failed!(..\QT_FlashTool_Refactor\Conn\USBSetting.cpp,195)" in QT_FLASH_TOOL.log and error "IsValidCOMPort(): Instance ID(USB\VID_8086&PID_0189\6&1279F1F3&0&5) (FlashToolLib/host/windows/com_enum.cpp:942)" in BROM_DLL_V5.log while read back, i am not sure if it is driver issue as preloader driver gets successfully installed
Click to expand...
Click to collapse
Try using usb deview to uninstall and reinstall the drivers or try changing the com port from sp flash tools itself or try any other pc.
Click to expand...
Click to collapse
i did it before rooting my phone...the process still remains the same...????
bladehunter said:
i did it before rooting my phone...the process still remains the same...????
Click to expand...
Click to collapse
Yes
Sudeep Duhoon said:
Procedure:
1. Download and install drivers Driver_Auto_Installer_v1.1236.00.7z.
If not working try these too PDAnet_4150.rar.
Problem in installation?? Go here
2. Download scatter from here .
3. Open SP flash tools, load scatter in sp flash tools and go to read back tab. (alternative download link of sp flash tools)
4. Click 'Add' and tap on added read back entry.
5. Select any path to save file and click ok, write 0x3E180000 in length and click ok.
6. Click on read back and connect phone without battery. Wait till it completes.
7. Once you see a green circle, close sp flash tools and switch on the phone.
8. When the phone is on, connect it to pc. See if any notification of 'usb debugging' comes in phone, if not, go to settings->about phone->and tap build number 7 times to enable debugging options.
9. Go back and enter developers options(in settings), and check usb debugging on.
10. Now run mtk driod tools and it will detect phone. (alternative download link of mtk droid tools)
11. In mtk droid tools, click 'root, backup and recovery' tab.
12. Click 'To process file ROM_ from Flash Tool.
13. Locate the file you got from read back.
14. Say no to make CWM recovery automatically and cancel to choose a recovery for similar phone.
15. Now wait again.
Once done, you will get your sp flashable backup in MTK Driod Tools/backup.
Read back complete.
Now follow this guide to root your Unite 2.
Click to expand...
Click to collapse
I cannot do this.. there is an error after 13% of the process completion.. Asking me to Press CTRL+ALT+T, What should i do.. is this step necessary to do if i only want to Root this phone and Perform Data REpartition.. Please Help me iam new to this Process
saikiransama said:
I cannot do this.. there is an error after 13% of the process completion.. Asking me to Press CTRL+ALT+T, What should i do.. is this step necessary to do if i only want to Root this phone and Perform Data REpartition.. Please Help me iam new to this Process
Click to expand...
Click to collapse
Not necessary, but highly recommend.
wat will be the approx size of the read back file ?
Scaning USB port failed!
Hi OP, plz help me out
M not able to readback following only this guide, getting the below error in logs:
"07/12/2014 19:40:39.305 FlashTool[8032][5132][D]: APCore::ConnMediaUSB:reConnect(): Scanning USB port...(..\QT_FlashTool_Refactor\Conn\ConnMedia.cpp,53)
07/12/2014 19:40:59.801 FlashTool[8032][8372][D]: FileUtils::CheckDirectory(): FileUtils::CheckDirectory(): the dir(C:\ProgramData\SP_FT_Logs) already exists.(..\QT_FlashTool_Refactor\Utility\FileUtils.cpp,44)
07/12/2014 19:41:09.407 FlashTool[8032][5132][D]: USBSetting::SearchUSBPortPool(): Scaning USB port failed!(..\QT_FlashTool_Refactor\Conn\USBSetting.cpp,195)"
can U plz let me know what possibly can be the reason for this error?
MTK droid tools 253 is not identifying the UNite 2 8GB model. What went wrong?
SOLVED - HAD TO WAIT FOR AROUND A MINUTE FOR THE FIRST TIME.
Problem with 8GB version
When I connect my phone to the computer, the preloader driver is installed and there's the typical connection sound in windows. But just after that it gets disconnected in like 1-2 secs. I am unable to use MTK Flash Tool because of it.
I have a 8GB rom version of unite 2. Anybody else having the same problem?? Any solutions???
PS: My phone is perfectly getting detected by adb in developer mode.
Rooted succesfully with u r method
Followed u r all step for Readback and Rooting Got success thanks for u r hard work
I have 4 Gb Version :good:
Sakthihari said:
wat will be the approx size of the read back file ?
Click to expand...
Click to collapse
512kb or 512b, i don't remember if that was in kb or b.
akash.gpta said:
When I connect my phone to the computer, the preloader driver is installed and there's the typical connection sound in windows. But just after that it gets disconnected in like 1-2 secs. I am unable to use MTK Flash Tool because of it.
I have a 8GB rom version of unite 2. Anybody else having the same problem?? Any solutions???
PS: My phone is perfectly getting detected by adb in developer mode.
Click to expand...
Click to collapse
Click download and then connect the phone, it will not get removed.
Niraj251 said:
Followed u r all step for Readback and Rooting Got success thanks for u r hard work
I have 4 Gb Version :good:
Click to expand...
Click to collapse
Press thanx, don't say it.
bootloop after flashing A rom
HERE IS THE FIRST OFFICIAL
CWM FOR KARBONN TITANIUM S20
ORIGINAL BOOT N RECOVERY .IMG
join FB GROUP:::<ww.facebook.com/groups/323894334469784>
sTOCK ROM (SOON BE UPLOADING)
Site ::: karbonnts20.blogspot.in/
nEWBIE PROBLEM THATS WHY LINKS ARE NOT ALLOWED TO POST
Rooting KArbonn Titanium s20
#Requirements:
"I am not responsible if you brick your phone"
CWM recovery (Link)
SU & Binary files (Link)
Use SP Flasher v 5.0xx to flash (Link) .
Download the scatter file MT6582(Link)
#Procedure :
Open SP flasher and choose scatter file Mt6582_android_emmc.txt
Goto recovery link and choose the CWM recovery (downloaded).
Now connect your device in switch off Mode with its battery inside and Download it
Now open CWM by pressing Vol up+Power Key
Choose "Install zip from sd card" >Choose zip from Sd card > select the update SU.zip
Reboot and we are done rooting.
for links check the site!!
Repartition Internal SDCARD
As we know this device {MTK6582}comes with 4GB ROM with APP data to be 1GB and user Storage 1.59 GB.
Such small APP space cause a lots of problems Thus best way is to repartition it with HKRom Manager.
For links visit the site :-htp://karbonnts20.blogspot.in/
"I am not responsible if u brick your phone , dead internal sd or so n so .Better do it on your own risk"
Requisites:
Hk rom manager.apk
CWM /TPRW recovery
A full backup CWM or TPRW.
Procedure:
Before you proceed take a full CWM or TPRW backup as phone internal partition may not work or respond sometimes.
Now install the app
Open the app and select mt6582 fast runner (2nd option) ::it will be the only highlighted option .
Choose your required data size (say 2GB , its fine ) and hit apply and now wait.
It will show boot into recovery ,hit yes
After 3 mins you are done. ReBoot it
Now You have 1.8GB APP space and 540MB for storage
"Remember all your phone data will be lost as phone is re-partitioned and Formatted. "
thanks to XDA
Ways to extract stock rom
How to Extract Stock Rom {Detailed procedure with Video tutorial}
FOR LINKS PLEASE VISIT THE SITE :- []ttp://karbonnts20.blogspot.in/[/url]
"This Tutorial is applicable MTK devices "
Required :-
SP flasher- [ttp://sh.st/o9xC5[/url]
MTK Droid Tools- [tp://sh.st/o895X[/url]
Scatter file
ABD Drivers
Ways to extract stock rom:- Video Links
1.Case I:- "If you have a unrooted and no CWM ANDROID Phone with USB Debugging Enabled "
Tutorial Visit:- ttp://sh.st/ocUme[/url]
2. Case II :- An Android Phone having CWM (with or without Root)
Tutorial Visit:- ttp://sh.st/ocOaC[/url]
3. Case III :- "A rooted Android phone (with or without CWM) USB Debugging Enabled"
Tutorial Visit :- ttp://sh.st/ocOBw[/url]
Thanks to XDA , and the Developers
Procedure:-
Case-I :If you have a unrooted and no CWM ANDROID Phone with USB Debugging Enabled
First TURN ON the USB Debugging Option :: ie , Settings>Developer options>USB debugging and install ADB drivers
Start MTK Droid Tools <Provided above> ,Grant the USB debugging request and wait till device get discovered .
Then click on BLOCKs Map and you will get all partition and their length .Here you can create a scatter file also. and minimise the window .\, We would require the location later.
Then TURN OFF the phone . OPEN SP flasher , Choose the scatter file you made or provided in the link.
Then Goto READBACK tab and add a readback file ie ROM_0
Click on ROM_0 and choose the destination Folder .
Now a Box will open and ask for Start address and length ,SET it in hex and do the following
start address:0x0000000 and length 0x7FB80000 [The length of FAT as in scatter file] ,Remember if you want the length shown in block map then just ADD 0x [length] .
Now HIT readback. Connect the Phone using USB with battery inside the phone and wait till its get discovered and yellow bar will represent the work.
It would nearly take 30-45 mins and we got our ROM_0 file.
Again Turn ON the phone and connect with USB debugging ON.
Open Minimised MTK Droid tools and Goto Root,backup tab and Hit Process ROM_0.
It will ask to make CWM recovery from original recovery ,if u want CWM fro your phone here you can get it HIT Yes.
After Processing finished we will get our SP flashable STOCK Rom Files in mtkdroidtools>backup
Hence we are done . And In RESULT we get ,ScAtter File ,SP Flashable STOCK Rom images and CWM Recovery for the phone.
Thank You
Case II:-An Android Phone having CWM (with or without Root)
Here we get CWM Backup For Stock Rom which is good for Porting like purposes.
Keep 3 GB of space empty in SD card.
First Turn OFF the Phone and HOLD UP+ Power Key
Enter to Recovery Menu>Backup and Restore
Hit Backup
After it completes Goto SDCARD>CLOCKWORKMOD>BACKUP
Result we get CWM Backup of STOCK ROM which can be flashed By CWM on Hitting restore in Backup and Restore.
Case-III:-A rooted Android phone (with or without CWM) USB Debugging Enabled
Here we can get CWM recovery,SP Flashable Stock Rom and to work with Rom files.
Connect the phone phone to PC via USB and turn ON the USB Debugging.Keep 3GB SDcard Space
Then start MTK Droid Tools and let it detect your Phone.
Then Hit ROOT button just at Down right.
Let it connect to phone and Grant the SU Permission in the phone.
The yellow mark in down left corner will turn Green .
Goto Root, Backup Tab and Select userdata and cache in Bacup option.
Now hit Backup. It would take and hour or so.
Then click on" prepare blocks for flash tools" and wait .
After it Finishes you have CWM recovery,SP Flashable Stock Rom and to work with Rom files.
Mtkdroidtools>backups>"[Phone name]">!imagesfor flashtool
Hope it help You
Hit like and Share
Hello again XDA, kirito9 here with another guide on how to root the Alcatel One Touch T'pop. I decided to make a guide because i have not seen any guide on XDA concerning this phone and rooting.
Disclaimer: Your warranty is now void. You do this in your own risk. I do not take any responsibility to your device.
BACKUP YOUR DEVICE BEFORE DOING ANYTHING IN THE EVENT SOMETHING GOES WRONG.
Requirements:
- Windows 7 PC ( tested only on this)
- ADB drivers
- MTK drivers
- MT6575 Scatter file
- CWM or TWRP recovery
- SP Flash Tools
- SuperSU
Lets Begin
Flashing CWM or TWRP
1. First thing to do is to make sure all required drivers are installed. Do that by downloading the Universal ADB driver from this link and install it.
2. Then install the MTK drivers so that SP flash tools can work. Get those here, extract and install the drivers for windows 7.
3. Download your preferred recovery either CWM or TWRP below and place somewhere on your computer where you can find it easily.
4. Download the SP flash tools here and extract them.
5. Download the MT6575 Scatter file attached below.
6. Download the SuperSU zip file and place it either on internal or external of the phone.
6. Go to the sp flash tools folder and run flashtool.exe as administrator.
7. Click on scatter loading and select the MT6575 scatter file you downloaded.
8. Click on the recovery checkbox and then click on the white space in location. Select the recovery of your choice.
9. Turn off the phone, remove the battery then reinsert it.
10. Click on download and then connect the phone.
11. Wait for the flashing to complete then remove your phone.
Rooting the phone.
1. Boot into recovery then go to install, select the SuperSu zip file and install it.
2. After the flashing is complete, reboot your phone and see the SuperSU app in the app drawer
Credits
- me
-Chainfire for his SuperSu
May you also upload any stock ROM for OT-4010D ???
Root : JB 4.2
Root Micromax A37B
1. Download The Kingroot APK here and install it to your phone.
2. Run King Root application.
3. Click on Root button. It take sometime for the rooting process.
4. Reboot device, done. :good:
Full Instructions here
Stock Rom : JB 4.2
Unbrick your Micromax A37B
1. Download Stock Rom from here (by firmwarefiles.com)and extract it.
2. Download mtk_usb driver from here and install it.
3. Open Sp flash tool, select scatter.txt.
4. Click on download.
5. Power off your device (confirm off), then connect usb cable. (without battery)
6. System will detect your device as mediatek_preloader_com.
7. Sp Tool will recognise your Phone and flashing will start.
8. Once the flashing process is completed, a green ring will appear on your system.
9. Dissconnect, Power On, Done :good:
Full Instructions with images here (by techsultan).
Nandroid Backup/restore (recommended)
Take Full backup of your Micromax A37b
Method 1:
You can do full backup/restore with Custom recovery (Carliv/TWRP).
Method 2:
1. Download Mtkdroid tool here (by gsmhosting)and extract it.
2. Download Pdanet andoid usb driver from here and install it.
3. Install BusyBox.apk in your device from playstore.
4. Enable debugging mode on your phone > Settings > Development. Tap 'android usb debugging' and make sure it's checked.
(if there is no option for development then go to setting > about phone > build number, tap on it 7 times, Go back to Settings menu and now you'll be able to see 01Development there.)
5. Open MTK Droid Tools folder with right-click on 'MTKdroidTools.exe' and Select 'Run as administrator'.
6. Wait several seconds while MTK Droid Tools communicates with your device. give root permission to adb-shell on your device.
7. Click the 'root' button in MTK Droid Tools to get temporary root shell.
8. Now get nvram backup. For full backup go to 2nd tab click on backup.
9. Here will be saved all backup \MtkDroidTools\backups.Done.
Full Instructions with images here (by rajit)
Custom Recovery
(Press Vol up and Power Key to boot in Recovery.)
You can flash it via fastboot.
fastboot flash recovery recovery.img
Click to expand...
Click to collapse
OR
You can flash via SP flashtool.
Ctr recovery for Mmx A37b
Ctr 2.2 here ( by programmer Shekhar.Hardknox)