[Marshmallow][official] Android 6.0 official update for sparkle v

[Marshmallow][official] Android 6.0 official update for sparkle v - Karbonn Sparkle V

OTA links are already there on xda, but here was no specific thread for sparkle v so i am writing one
Google has released the OTA files for sparkle v and other android one devices.
NOTE: To update your phone using OTA files your phone should be running Stock lollipop or atleast stock recovery
If you are running a custom rom or custom recovery then before proceeding to this guide you must revert back to stock lollipop using sp flash tool
Pre-requisites: 1.Your phone should be atleast 60% charged
2. Back up all important data (just to be safe)
3. Make sure you have the stock lollipop rom so that you can get your phone back if anything goes wrong.
GUIDE-
Sparkle V users can easily update their device by following these steps:
Step 1: Download the official Marshmallow OTA file from here https://android.googleapis.com/packages/ota/google_sparklevsprout_sparklev/d1178816334e0c160d435ab0a88f78a5005053c0.signed-sprout-karbonn-ota-2280749-omit-oem.zip
Step 2: Connect your smartphone to computer using the original USB cable.
Step 3: Copy and paste the OTA zip files to phone's storage and make a note of its location.
Step 4: Boot your smartphone into recovery mode or stock recovery: Disconnect the phone from computer, and then turn it off.
Press and hold both the Volume and the Power buttons until the display turns on and enters bootloader mode.
Hit the volume button to open the Recovery menu and then press the power button to select it. Your phone should now boot into recovery mode.
At this moment, a dead Android with an exclamation mark should appear on the screen. Now press and hold Power button for three seconds and then hit the Volume up button once to progress into recovery mode.
Step 5: Return to the main recovery screen and choose 'install update from sdcard'.
Step 6: Then select the OTA zip file using the volume buttons for navigation and the Power button to select any file or open a folder. After you select the zip file, confirm its installation and the update should start installing on your device.
Step 7: Once the installation is done, return to main screen of recovery. Choose Reboot system now to restart the phone and boot into the newly installed Android 6.0 Marshmallow OTA update from Google.
Voila!! You are running official Android 6.0
I found this on ibtimes. I HAVE JUST COPY PASTED the guide for convenience. Hit thanks if helped.

Related

[Q] - Want to root my Note 10.1 (N8013) to 4.3 or 4.4

I sure would like to upgrade my Samsung Tablet to 4.3 or 4.4.
If anyone can provide a step by step on "how to" for CyanogenMod or other reliable roms will be greatly appreciated.
My tablet is 4.1.2 and no other customization applied or rooted.
Many thanks in advance for your help on guiding this newbie to Custom Rom world!
Jay

jnoh1611 said:
I sure would like to upgrade my Samsung Tablet to 4.3 or 4.4.
If anyone can provide a step by step on "how to" for CyanogenMod or other reliable roms will be greatly appreciated.
My tablet is 4.1.2 and no other customization applied or rooted.
Many thanks in advance for your help on guiding this newbie to Custom Rom world!
Jay
Click to expand...
Click to collapse
The term you're looking for is "flashing a rom", not "rooting a rom". Flashing a rom is not as hard as some people make it out to be, it's a fairly simple process. You'll need a computer nearby, your tablet USB cord, a recovery, and the rom you want.
-Downloading the Recovery-
You'll need to download a custom recovery before you can flash a rom. I personally use TWRP, so the steps that follow will be for TWRP:
1. Go to the official website of TWRP and download the Odin method (It should be the last download on the list) http://www.teamw.in/project/twrp2
2. If the download doesn't come with Odin, download it from here: http://odindownload.com/
3. Put your tablet into download mode by holding the Power + Volume down button.
4. Run Odin on your PC and then plug your tablet into the the USB port on your computer.
5. Load the twrp file you downloaded as a PDA and then press Start.
If you have done the steps above correctly, your tablet should reboot and nothing should change.
-Backing up your tablet-
Before you go any further, you will need to make a nandroid backup of your device. Here's the step to do that:
1. While your tablet is on, press and hold the Power + Volume Up (not down) button until you see the "Galaxy Note 10.1" boot screen.
2. You should now be in TWRP recovery. Press "backup" and then pick the location where you want to back up.
3. Start the backup and wait for a few minutes. Once completed, reboot your tablet.
You should also back up your apps using Titanium Backup or some similar app.
-Flashing the rom-
Flashing a custom rom is a very easy process. Here's how to do that:
1. Find the rom you want and download it on your tablet (or download it on your PC and move the files to your tablet)
2. Now go into recovery again (Power + Volume Up)
3. Press "Wipe"
WARNNG: The following steps will wipe your data, make sure you had back it up before proceeding or else you will lose your data!
4. Don't change any of the preset settings and begin wiping your tablet
5. Go back into the main menu of TWRP and press "Install"
6. Find the zip file of the Custom Rom and select it.
7. Press install and wait until the recovery has finish flashing the rom
8. If successful, you should be running a custom rom when you restart your tablet!

link6155 said:
The term you're looking for is "flashing a rom", not "rooting a rom". Flashing a rom is not as hard as some people make it out to be, it's a fairly simple process. You'll need a computer nearby, your tablet USB cord, a recovery, and the rom you want.
-Downloading the Recovery-
You'll need to download a custom recovery before you can flash a rom. I personally use TWRP, so the steps that follow will be for TWRP:
1. Go to the official website of TWRP and download the Odin method (It should be the last download on the list) http://www.teamw.in/project/twrp2
2. If the download doesn't come with Odin, download it from here: http://odindownload.com/
3. Put your tablet into download mode by holding the Power + Volume down button.
4. Run Odin on your PC and then plug your tablet into the the USB port on your computer.
5. Load the twrp file you downloaded as a PDA and then press Start.
If you have done the steps above correctly, your tablet should reboot and nothing should change.
-Backing up your tablet-
Before you go any further, you will need to make a nandroid backup of your device. Here's the step to do that:
1. While your tablet is on, press and hold the Power + Volume Up (not down) button until you see the "Galaxy Note 10.1" boot screen.
2. You should now be in TWRP recovery. Press "backup" and then pick the location where you want to back up.
3. Start the backup and wait for a few minutes. Once completed, reboot your tablet.
You should also back up your apps using Titanium Backup or some similar app.
-Flashing the rom-
Flashing a custom rom is a very easy process. Here's how to do that:
1. Find the rom you want and download it on your tablet (or download it on your PC and move the files to your tablet)
2. Now go into recovery again (Power + Volume Up)
3. Press "Wipe"
WARNNG: The following steps will wipe your data, make sure you had back it up before proceeding or else you will lose your data!
4. Don't change any of the preset settings and begin wiping your tablet
5. Go back into the main menu of TWRP and press "Install"
6. Find the zip file of the Custom Rom and select it.
7. Press install and wait until the recovery has finish flashing the rom
8. If successful, you should be running a custom rom when you restart your tablet!
Click to expand...
Click to collapse
I think he needs Root too... other than that, great write up!

link6155 and lilbluemirage ,
I thank you both for the 1. great step by step instruction. 2. Understanding the need of a Newbie who has no idea how to ask proper question!
Since I heard that Sammy is going to release long-waited 4.4 update (After I posted the question), I decided to wait a bit longer before I go through with flashing by following your kind instruction. I still am not sure whether I should root before flashing it or after, though. Anyway, I will come back if Sammy fail me (sigh) and will definitely follow your guidance.
Thanks again and Have a wonderful day!

[Q] Help with retail USA XT1032 (Can't see sim)

I bought a 16gb moto g when they were released straight from the motorola website.
USA, using an AT&T sim.
After a while, I unlocked in and played around, and the last thing I've done was follow this guide to update to 5.1.
(It won't let me post a link, just append /watch?v=vPwsdN66spM to youtube.)
Published on 3 Apr 2015
In this video, I'll show you How to Install the NEW Android 5.1 Lollipop on Motorola Moto G 1st Gen XT1033 and XT1032 Variants.
Backup your phone before following the procedure as you'll loose all your data.
Prerequisites for your Moto G :-
1. Unlocked Bootloader
Prerequisites for your PC (Doesn't work on MAC) :-
1. Motorola Device Manager (Motorola Drivers)
2. Universal ADB Driver
Downloads :-
Complete Guide (In case, you didn't Understand something in the Video)
1. First download and extract the two files a)Stock Android to GPe.rar and b)Android 5.1.rar
2. Power Off! your phone and boot to bootloader mode by pressing Volume Down Key and Power button simultaneously and connect it to your PC.
3. In the Stock Android to GPe folder (that you extracted) run the Android 5.x TO 4.4.4 GPE.bat file if you are on any Android Lollipop version or ANY KK FIRMWARE TO 4.4.4 GPE.bat if you are on Kitkat.
4. After the flashing is complete and Moto G boots into the Android 4.4.4 Welcome screen , just POWER OFF the device.
5. Again boot into Bootloader and then Press the Volume Down Button followed by Volume UP button to select Recovery.
When you see the Android logo with Exclamation mark, HOLD the Volume UP button and then press the Power button (1-2 times) to boot into Stock Recovery.
Now press Volume Down Button followed by Power button to select "Install Update from ADB".
6. Now connect your phone to PC.In the Stock Android to GPe folder (that you extracted) run the SIDELOAD LOLLIPOP.bat file to sideload Android 5.0.1 GPe.
7. After it is complete and you see "Install from ADB Complete" on your phone select Reboot System by pressing the Power Button.
8. After the flashing is complete and Moto G boots into the Android 5.0.1 Welcome screen , FOLLOW STEPS 4-5 AGAIN.TO GET INTO RECOVERY THIS TIME, PRESS THE POWER BUTTON AND THEN THE VOLUME UP BUTTON INSTEAD OF HOLDING VOLUME UP AND THEN PRESSING THE POWER BUTTON.
9. Now connect your phone to PC.In the Android 5.1 folder (that you extracted) run the Install OTA.bat file to sideload Android 5.1 GPe.
10. After it is complete and you see "Install from ADB Complete" on your phone select Reboot System by pressing the Power Button.
You have successfully Installed ANDROID 5.1 on your MOTO G.
That's it..
Enjoy your smooth and fast new LOLLIPOP....
Thanks for watching this video.Do comment below and like this video.
Don't forget to subscribe to my channel for more cool stuff, How to videos,Reviews,Tutorials and much more...
Till then Stay Connected...
Click to expand...
Click to collapse
Now it doesn't see the sim.
Any suggestions?
Thanks.

How To Root Samsung GALAXY J2 (SM-J200/G/H/F/M) UPDATED!

Hi Guys,
I Am Going To Guide You How To Root Your Samsung Galaxy J2 (All 2015 Variants).
I AM NOT RESPONSIBLE FOR ANY DAMAGE OR ANY HARM OCCURRED WITH YOU DURING THE PROCESS !
GUYS, FOLLOW EACH STEP CORRECTLY FOR THE PERFECT SOLUTION.
Your Samsung Galaxy J2 May Be Have Latest Or Lowest Version Of Firmware, It Doesn't Matter.
STEP 1: UNLOCKING THE BOOTLOADER :-
Switch ON Your Phone.
Goto >>SETTINGS >>ABOUT DEVICE>>TAP THE BUILD NUMBER 3 TO 5 TIMES.
Get Back To SETTINGS And Goto >>DEVELOPER OPTIONS>>TURN "ON" OEM UNLOCK.
This Will Unlock Your BOOTLOADER.
STEP 2: DOWNLOADING THE TWRP RECOVERY (CUSTOM RECOVERY) :-
Visit TWRP Homepage.
Download The File "twrp-3.1.1-0-j2lte.img.tar"
(The Latest Version Of TWRP Recovery For Galaxy J2)
OR Just Google It, You Will Find It Easily.
STEP 3: DOWNLOADING SAMSUNG ANDROID USB DRIVERS SETUP AND ODIN TOOL :-
Visit Samsung Support Files And Download Latest Android USB Drivers For Samsung.
And Also Download Latest Version Of ODIN Tool.
(These Both Files Can Be Found Very Easily By Google)
STEP 4: FLASHING THE TWRP RECOVERY.
Make Sure You Have Installed The Latest USB Drivers For Samsung And Have Latest Version Of ODIN Tool.
Switch OFF Your Phone. (To Make Sure It Is Switched Off, Remove Battery And Re - Insert It)
Boot Your Phone Into Download Mode. (This Can Be Easily Done By Holding The "VOLUME DOWN + HOME + POWER" Buttons At A Same Time.)
Now Your Phone's Screen Shows Download Mode.
Open The "ODIN.EXE" File (After The Extracting The ODIN.ZIP).
Click On "PDA" OR "AP" Then Browse And Select The "twrp-3.1.1-0-j2lte.img.tar" File.
Now, Connect Your Phone To The PC With The USB Cable. (Make Sure That Your Cable Is Not Damaged And It is At It's Peak Performance.)
Wait Until You See The "Added" Message In The Log Section Of ODIN Tool.
Now, Click On "START" To Begin The Flashing Process.
Wait Until The Process Is Completed And Then ODIN Shows The "PASS" OR "RESET" Message.
Disconnect The Phone From The PC And Let It To Power ON Itself.
STEP 5: DOWNLOADING SUPERSU FILE AND FLASHING IT WITH TWRP RECOVERY :-
Search The File "EXPERIMENTAL-BETA-SuperSU-v2.66-20160103015024.Zip" And Download It.
Put It Into Your Internal Or External Storage.
Switch OFF Your Phone.
Boot Your Into Recover Mode. (This Can Be Easily Done By Holding The "VOLUME UP + HOME + POWER" Buttons At A Same Time.)
Now Instead Of Stock Recovery, You Will See The TWRP Recovery.
At The First Time It Will Ask For Mount System.
Swipe And Give Permissions To Mount The System.
Now, Click On "INSTALL" And Browse Your Downloaded SUPERSU.Zip And Swipe To Flash It.
Wait Till The Flash Is Completed And Then Click On "REBOOT SYSTEM".
The Phone Will Reboots Itself. (It Will Reboot For Two Times, Don't Worry ; Let It To Boot Completely And Don't Interrupt The Process.
After The Successful Boot Up, It Will Show Android Is Upgrading And Takes You To The Home Launcher ; Launch Your App Drawer To See Your SUPERSU App Installed.
STEP 6: ROOT VERIFICATION :-
Goto Play Store And Download Root Checker Basic App.
Launch It And Verify Yourself.
KEEP SMILING!!!
DOWNLOAD LINKS :-
1. Samsung Android USB Drivers :
http://developer.samsung.com/galaxy/others/android-usb-driver-for-windows
2. ODIN Tool :
http://odindownload.com/mobile/
3. TWRP Recovery :
https://dl.twrp.me/j2lte/
4. SUPERSU :
https://forum.xda-developers.com/showpost.php?p=64161125

Peeran said:
Hi Guys,
I Am Going To Guide You How To Root Your Samsung Galaxy J2 (All 2015 Variants).
I AM NOT RESPONSIBLE FOR ANY DAMAGE OR ANY HARM OCCURRED WITH YOU DURING THE PROCESS !
GUYS, FOLLOW EACH STEP CORRECTLY FOR THE PERFECT SOLUTION.
Your Samsung Galaxy J2 May Be Have Latest Or Lowest Version Of Firmware, It Doesn't Matter.
STEP 1: UNLOCKING THE BOOTLOADER :-
Switch ON Your Phone.
Goto >>SETTINGS >>ABOUT DEVICE>>TAP THE BUILD NUMBER 3 TO 5 TIMES.
Get Back To SETTINGS And Goto >>DEVELOPER OPTIONS>>TURN "ON" OEM UNLOCK.
This Will Unlock Your BOOTLOADER.
STEP 2: DOWNLOADING THE TWRP RECOVERY (CUSTOM RECOVERY) :-
Visit TWRP Homepage.
Download The File "twrp-3.1.1-0-j2lte.img.tar"
(The Latest Version Of TWRP Recovery For Galaxy J2)
OR Just Google It, You Will Find It Easily.
STEP 3: DOWNLOADING SAMSUNG ANDROID USB DRIVERS SETUP AND ODIN TOOL :-
Visit Samsung Support Files And Download Latest Android USB Drivers For Samsung.
And Also Download Latest Version Of ODIN Tool.
(These Both Files Can Be Found Very Easily By Google)
STEP 4: FLASHING THE TWRP RECOVERY.
Make Sure You Have Installed The Latest USB Drivers For Samsung And Have Latest Version Of ODIN Tool.
Switch OFF Your Phone. (To Make Sure It Is Switched Off, Remove Battery And Re - Insert It)
Boot Your Phone Into Download Mode. (This Can Be Easily Done By Holding The "VOLUME DOWN + HOME + POWER" Buttons At A Same Time.)
Now Your Phone's Screen Shows Download Mode.
Open The "ODIN.EXE" File (After The Extracting The ODIN.ZIP).
Click On "PDA" OR "AP" Then Browse And Select The "twrp-3.1.1-0-j2lte.img.tar" File.
Now, Connect Your Phone To The PC With The USB Cable. (Make Sure That Your Cable Is Not Damaged And It is At It's Peak Performance.)
Wait Until You See The "Added" Message In The Log Section Of ODIN Tool.
Now, Click On "START" To Begin The Flashing Process.
Wait Until The Process Is Completed And Then ODIN Shows The "PASS" OR "RESET" Message.
Disconnect The Phone From The PC And Let It To Power ON Itself.
STEP 5: DOWNLOADING SUPERSU FILE AND FLASHING IT WITH TWRP RECOVERY :-
Search The File "EXPERIMENTAL-BETA-SuperSU-v2.66-20160103015024.Zip" And Download It.
Put It Into Your Internal Or External Storage.
Switch OFF Your Phone.
Boot Your Into Recover Mode. (This Can Be Easily Done By Holding The "VOLUME UP + HOME + POWER" Buttons At A Same Time.)
Now Instead Of Stock Recovery, You Will See The TWRP Recovery.
At The First Time It Will Ask For Mount System.
Swipe And Give Permissions To Mount The System.
Now, Click On "INSTALL" And Browse Your Downloaded SUPERSU.Zip And Swipe To Flash It.
Wait Till The Flash Is Completed And Then Click On "REBOOT SYSTEM".
The Phone Will Reboots Itself. (It Will Reboot For Two Times, Don't Worry ; Let It To Boot Completely And Don't Interrupt The Process.
After The Successful Boot Up, It Will Show Android Is Upgrading And Takes You To The Home Launcher ; Launch Your App Drawer To See Your SUPERSU App Installed.
STEP 6: ROOT VERIFICATION :-
Goto Play Store And Download Root Checker Basic App.
Launch It And Verify Yourself.
KEEP SMILING!!!
DOWNLOAD LINKS :-
1. Samsung Android USB Drivers :
http://developer.samsung.com/galaxy/others/android-usb-driver-for-windows
2. ODIN Tool :
http://odindownload.com/mobile/
3. TWRP Recovery :
https://dl.twrp.me/j2lte/
4. SUPERSU :
https://forum.xda-developers.com/showpost.php?p=64161125
Click to expand...
Click to collapse
Will this twrp works on j23g? I don't think so..

Yes,of course.

Is it working on all type of j2?

Samial said:
Is it working on all type of j2?
Click to expand...
Click to collapse
Nope

here`s the twrp for j23g
https://forum.xda-developers.com/ga...p-3-0-2-1-samsung-galaxy-j2-sm-j200h-t3486994
and for root Just use magisk, it works on almost all smartphones and has much more features.

problems faced and solns found
1. During twrp flashing using odin, my stock recovery kept patching the twrp after reboots. So i couldn't install twrp succesfully. To fix this I unchecked "reboot" option in odin (thanks to another xda rooting guide)and switched off device manually after flashing. Then booted into recovery by pressing "home+vol up+power". this time stock rom was gone and twrp was there to welcome me.
2. i ended up in a bootloop after flashing the aforementioned superuser zip file. Instead i flashed BETA-SuperSU-v2.74-2-20160519174328.zip and fixed the bootloop.
Note- My device is Samsung Galaxy j200-G.
Here are some links to go through(as i did) ,if you face same problems:
1. https://twrp.me/samsung/samsunggalaxyj2.html
2. https://forum.xda-developers.com/ga...p-3-0-2-1-samsung-galaxy-j2-sm-j200h-t3486994
3. https://www.androidinfotech.com/2016/07/root-samsung-galaxy-j2-sm-j200g-511.html

How I can unlock bootloader permanently??
SM-J200G

Will this work on SAMSUNG J200GU?

But unable to access twrp 2nd time it show custom recovery blocked by frp lock

abhi91ar said:
But unable to access twrp 2nd time it show custom recovery blocked by frp lock
Click to expand...
Click to collapse
Turn on Oem unlock in developer options.

§Ani§ said:
Turn on Oem unlock in developer options.
Click to expand...
Click to collapse
Already turned on but problem still exists. What to do now? Help me?

Ok i will try

I s there any best ROM with higher version for Samsung SM-J200H

Rooting samsung j200gu
abinashdash17 said:
1. During twrp flashing using odin, my stock recovery kept patching the twrp after reboots. So i couldn't install twrp succesfully. To fix this I unchecked "reboot" option in odin (thanks to another xda rooting guide)and switched off device manually after flashing. Then booted into recovery by pressing "home+vol up+power". this time stock rom was gone and twrp was there to welcome me.
2. i ended up in a bootloop after flashing the aforementioned superuser zip file. Instead i flashed BETA-SuperSU-v2.74-2-20160519174328.zip and fixed the bootloop.
Note- My device is Samsung Galaxy j200-G.
Here are some links to go through(as i did) ,if you face same problems:
1. https://twrp.me/samsung/samsunggalaxyj2.html
2. https://forum.xda-developers.com/ga...p-3-0-2-1-samsung-galaxy-j2-sm-j200h-t3486994
3. https://www.androidinfotech.com/2016/07/root-samsung-galaxy-j2-sm-j200g-511.html
Click to expand...
Click to collapse
Wow thank you so much bro I now have rooted my phone!! (Samsung J200GU):good: :laugh:
Note: I flashed SR5-SuperSU-v2.78-SR5-20161130091551 instead of the 2.74 mentioned above?

abhi91ar said:
Already turned on but problem still exists. What to do now? Help me
Click to expand...
Click to collapse
Turn off auto reboot in odin and then flash.

Does this work on Sm-J200h? Trying to root my device but I am doing a little research before I do.

Phones bricked now....
you dog my phones bricked should of mentioned to make a backup u fuk wit

Nice Tutorials
Hey i m ramcharan thanks nice guide how to root samsung J200G

Need to get back to 100% stock

My note 5 has been in a sort of root/not root limbo where I haven't bothered to update or do anything with it and I just want to get it back to stock. All I remember is that I need a stock rom and a kernel, but it's been so long that I don't remember everything. Anyone wanna help me get back to a usable stock state?

tldr: You will need a computer for this, download n920T Stock firmware from here and then odin it.
Preparation Steps:
1) Back Up all your Personal Data( if you are running TWRP it is recommended to Backup EFS partition and keep a copy somewhere safe)
2) If you are previously running a custom rom you should wipe your System and data partition in TWRP otherwise it will not boot after this.
Actual Steps:
1) Download the stock firmware for N920T only from here .
2) Download Odin from here
3) unzip zip file and run Odin.
4) unzip the stock firmware and extract the ".tar.md5" file.
5) now in Odin on the right side, click on AP button and select the file you extracted in step 4. (if odin goes unresponsive leave it for 5 minutes it will be back after fully loading )
6) assuming you have backedup all your important data now turn off your phone and restart it in download mode by pressing (power and home and volume down button)
7) Press volume up if it gives a warning and enter download mode.
8) now connect your phone with your computer and you will see on top left a box in Id:com will turn blue with your port number written on it.
9) DO NOT change any setting from options tab.
10) Press Start you will see progress and once its done, phone will restart.

I keep getting an invalid error when I try to download that firmware. I crashed my n920t and been trying to flash a firmware to get it back but the only thing working or flashing in Odin is twrp. but I can't get it to boot in twrp. any ideas?

[GUIDE] [Q/R]How to Install TWRP 3.4.0-0

1) Download Odin3 v3.13.1, Samsung USB Drivers , Download Latest TWRP.img.tar , Disable_forcedencryption patch,
2) Go to Settings App, Developer Options and enable OEM Unlock (If you don't see Developer Setings, go into About phone>Software info and tap "Build number" 10 times to show Developer Options menu).
3) Do a backup of all your important data and files in your phone.
4) Shutdown the phone. Once it's off, Power it On in Download Mode (Connect your phone to your PC, press and hold Power, Vol + and Vol - buttons together )
5) Open Odin3, go in Option section and untick "Auto-reboot". Once that click the "AP" button and select the TWRP tar you downloaded before, then press the "Start" button.
6) Once Odin3 finished to flash the recovery (you should see a "PASS" message), force reboot your phone (Press and hold Power and Vol - buttons together) and once the screen is off, press and hold Power and Vol + buttons together to boot in TWRP.
7) Once TWRP is booted you first need to decrypt your /data partition. To do so touch Wipe>Format Data ( you will lose all data ) and follow the instructions in screen.
8) Once it finished go back at the home screen and touch Reboot>Recovery. TWRP should be able to mount your data partition. Now flash the Disable_forcedencryption patch
9) You are done. Flash your favorite ROM.zip
Instructions from here were updated to be able to use twrp after Android 10 update.

Is this for Android 10?

Punitverma2010 said:
Is this for Android 10?
Click to expand...
Click to collapse
Yes and doesnt it say there at the last line

Hi, this is just for switching from Stock Locked BL devices right? If previous instructions on the last post have been followed, then the .img from twrp.me can be flashed to recovery in already installed TWRP right? I have 3.3 installed so upgrading can be done from recovery itself, if I'm not wrong?

thes3usa said:
Hi, this is just for switching from Stock Locked BL devices right? If previous instructions on the last post have been followed, then the .img from twrp.me can be flashed to recovery in already installed TWRP right? I have 3.3 installed so upgrading can be done from recovery itself, if I'm not wrong?
Click to expand...
Click to collapse
Yes update using twrp.img
Download twrp.img and flash as recovery but ROMs require you to be on ONEUI2.0

nice, but i have a question,
should i do flash more 2 files Magisk & RMM Bypass ??? (like ver 3.3.0 here)

Database Info

welcome