This guide is applicable for hard bricked Coolpad Dazen 1 with Qualcomm HS-USB QDloader 9008, no fastboot, no led on charging, dead phone.
I am writing this guide as simple as can be for all. I no longer own this device.
DISCLAIMER: I have personally revived my Coolpad Dazen 1 (8297L-I00) using this method and tested it twice by hardbricking and unbricking my device before posting it here. I bear no responsibility of whatever that happens to your device/sdcard/computer by using this guide.
What will you need?
• A dead Coolpad Dazen 1 (8297L-I00)
• A PC/Laptop.
• A 2GB or above MicroSD Card. (2GB would suffice)
• Win32DiskImager
• eMMC image of Coolpad Dazen 1. Download
• Stock Rom with flash tools & drivers. Download
• A little brain and common sense.
Steps:
• Connect your MicroSD card to PC in mass storage mode using any card reader or old phone which supports mass storage mode.
• Format your MicroSD card in FAT32 format, quick format will work.
• Extract Coolpad Dazen 1 eMMC image to a folder. It will be of 200MB after extracting.
• Install Win32DiskImager and write Coolpad Dazen 1 eMMC image to your MicroSD card. Kindly select the right drive letter for your SD card otherwise your will severely damage any other drive or your PC hard disk.
• After successful completion of writing eMMC backup image to SD card, insert the MicroSD card in your device and remove all sim cards. Insert battery into your device now. Do not power it on yet.
• Now you can boot to fastboot mode with the eMMC image on SDCARD.
• Connect your phone in fastboot mode, steps for which are : -
A. Press and hold the Volume Up key
B. With the Volume Up key, connect the phone to your PC/Laptop with USB cable
C. Press volume up to confirm on the first screen.
• Now you can flash the stock firmware with ygdp tools. (There's plenty of guide for flashing with YGDP tools. Google is your friend)
• DO NOT disconnect the device during flashing procedure.
• After the flashing procedure is completed, disconnect the USB cable, remove the microSD card and boot the phone normally by long pressing the Power button.
Your Coolpad Dazen 1 is unbricked now.
Credits:
Jimmyz0r@Xda for his thread so I can copy paste some steps from there.
AndroidMTKSite for Stock Rom and Flash Tools
You for trying this guide.
Me for making this guide and creating eMMC backup.
zardaman said:
This guide is applicable for hard bricked Coolpad Dazen 1 with Qualcomm HS-USB QDloader 9008, no fastboot, no led on charging, dead phone.
I am writing this guide as simple as can be for all. If any queries, just post it on the comment section.
DISCLAIMER: I have personally revived my Coolpad Dazen 1 (8297L-I00) using this method and tested it twice by hardbricking and unbricking my device before posting it here. I bear no responsibility of whatever that happens to your device/sdcard/computer by using this guide.
What will you need?
• A dead Coolpad Dazen 1 (8297L-I00)
• A PC/Laptop.
• A 2GB or above MicroSD Card. (2GB would suffice)
• Win32DiskImager
• eMMC image of Coolpad Dazen 1. Download
• Stock Rom with flash tools & drivers. Download
• A little brain and common sense.
Steps:
• Connect your MicroSD card to PC in mass storage mode using any card reader or old phone which supports mass storage mode.
• Format your MicroSD card in FAT32 format, quick format will work.
• Extract Coolpad Dazen 1 eMMC image to a folder. It will be of 200MB after extracting.
• Install Win32DiskImager and write Coolpad Dazen 1 eMMC image to your MicroSD card. Kindly select the right drive letter for your SD card otherwise your will severely damage any other drive or your PC hard disk.
• After successful completion of writing eMMC backup image to SD card, insert the MicroSD card in your device and remove all sim cards. Insert battery into your device now. Do not power it on yet.
• Now you can boot to fastboot mode with the eMMC image on SDCARD.
• Connect your phone in fastboot mode, steps for which are : -
A. Press and hold the Volume Up key
B. With the Volume Up key, connect the phone to your PC/Laptop with USB cable
C. Press volume up to confirm on the first screen.
• Now you can flash the stock firmware with ygdp tools. (There's plenty of guide for flashing with YGDP tools. Google is your friend)
• DO NOT disconnect the device during flashing procedure.
• After the flashing procedure is completed, disconnect the USB cable, remove the microSD card and boot the phone normally by long pressing the Power button.
Your Coolpad Dazen 1 is unbricked now.
Credits:
Jimmyz0r@Xda for his thread so I can copy paste some steps from there.
AndroidMTKSite for Stock Rom and Flash Tools
You for trying this guide.
Me for making this guide and creating eMMC backup.
Click to expand...
Click to collapse
i got my screen back now, but in device manager it detect as unknown device, i tried so many drivers, but no luck
without battery i get "coolpad andriod bootloader interface" in device manager, but cant flash with ygpd, and then i try the same method of reviving coolpad flashing recovery.img or system.img
target reported max download size of 268435456 bytes,
erasing 'system'...
FAILED (remote: Partition table doesn't exist)
what to do now?? please help
ngaia said:
without battery i get "coolpad andriod bootloader interface" in device manager, but cant flash with ygpd, and then i try the same method of reviving coolpad flashing recovery.img or system.img
target reported max download size of 268435456 bytes,
erasing 'system'...
FAILED (remote: Partition table doesn't exist)
what to do now?? please help
Click to expand...
Click to collapse
I would suggest you first uninstall all drivers with USBDEVIEW and restart your pc in test mode. to restart in test mode, open command prompt and type
Bcdedit.exe -set TESTSIGNING ON
then restart your pc, you will see test mode watermark in bottom right corner of the monitor. Reinstall coolpad usb drivers, after that you can flash your mobile with Ygdp tool again.
To flash with ygdp tool your phone has to be in download mode, to do that press volume up in power off state and insert usb cable, you will see a confirmation screen. press volume up to confirm and you are good to go.
Hope it helped.
my coolpad dazen 1 is dead i think
my coolpad dazen 1 was bricked when i applied my miui update and after that i used ur method and while flashing it struck at 33% and after that i am not able to switch on my phone whenever i coonect the phone through usb its led light turns red and it starts vibrating but no luck how can i get my device back to life please tell in a serious danger
awsomehacker said:
my coolpad dazen 1 was bricked when i applied my miui update and after that i used ur method and while flashing it struck at 33% and after that i am not able to switch on my phone whenever i coonect the phone through usb its led light turns red and it starts vibrating but no luck how can i get my device back to life please tell in a serious danger
Click to expand...
Click to collapse
Sorry for the late reply. I'm offline for a while due to personal matters. Did you follow the step EXACTLY as mentioned?
Try redoing all the steps and if not successful. You may contact me personally on whatsapp. I'll pm you my number if necessary.
Pls contact me as soon as possible
My no is 9818195778
thanku so much
thnk u so much buddy.... i got my coolpad dazen 1 back .....its working awesome....
Not getting anywhere
Its still showing qualcomm HSqdloader mode
Plz help me out
Can you provide qfil(qpst) files
coolpad dazen 1 dead pls help me pls
I have coolpad dazen 1...and I root my coolpad dazen 1 phone and install miui after this I have got one update of miui when I start to update my phone my phone is dead and no vibration or no signal...its totally dead what can I do I want my coolpad dazen 1 back pls help me...:crying::crying::crying::crying::crying::crying::crying::crying:
Coolpad Dazen 8297L not working
I am trying to install the stock rom to the device using YGDP Tool. While processing it getting error at 11%. Yesterday the error was in progress of Cell 0. Today it showing in Cell 1. Please help.
Thanks
Vijesh
hi, after following this procedure I am still not able to get my IMEI numbers back ,
its showing both imei as null .. while dialing *#06# ,
so can you backup your EFS partition and share with me plz ... i m in big trouble ... warranty also exceed so cant go to service center
Coolpad 8297-t01 error
i have coolpad 8297-T01 and i have tried flashing it using ygd tool but all i get is error. all drivers are ok but i dont know what next. help pls
Superb brother my dazen got life again.
I've lost hope on the device but got it back.
You have done an awesome work brother.
I tried to do this but doesnt works out any suggestions just forming 9008 port
rahul_rocks3 said:
I tried to do this but doesnt works out any suggestions just forming 9008 port
Click to expand...
Click to collapse
Bro first download ygdp tool and stockfiirmware of dazen 1from above links. And install eMMC image into a 2gb micro sd card using win32disk image writer. then insert sd card in phone and connect it to computer through usb by pressing volume +key. youll get bootliader screen defenetly. Then continue flashing through YGDP Tool. Your phone will come back to life.
---------- Post added at 09:22 AM ---------- Previous post was at 09:18 AM ----------
zardaman said:
This guide is applicable for hard bricked Coolpad Dazen 1 with Qualcomm HS-USB QDloader 9008, no fastboot, no led on charging, dead phone.
I am writing this guide as simple as can be for all. If any queries, just post it on the comment section.
DISCLAIMER: I have personally revived my Coolpad Dazen 1 (8297L-I00) using this method and tested it twice by hardbricking and unbricking my device before posting it here. I bear no responsibility of whatever that happens to your device/sdcard/computer by using this guide.
What will you need?
â?¢ A dead Coolpad Dazen 1 (8297L-I00)
â?¢ A PC/Laptop.
â?¢ A 2GB or above MicroSD Card. (2GB would suffice)
â?¢ Win32DiskImager
â?¢ eMMC image of Coolpad Dazen 1. Download
â?¢ Stock Rom with flash tools & drivers. Download
â?¢ A little brain and common sense.
Steps:
â?¢ Connect your MicroSD card to PC in mass storage mode using any card reader or old phone which supports mass storage mode.
â?¢ Format your MicroSD card in FAT32 format, quick format will work.
â?¢ Extract Coolpad Dazen 1 eMMC image to a folder. It will be of 200MB after extracting.
â?¢ Install Win32DiskImager and write Coolpad Dazen 1 eMMC image to your MicroSD card. Kindly select the right drive letter for your SD card otherwise your will severely damage any other drive or your PC hard disk.
â?¢ After successful completion of writing eMMC backup image to SD card, insert the MicroSD card in your device and remove all sim cards. Insert battery into your device now. Do not power it on yet.
â?¢ Now you can boot to fastboot mode with the eMMC image on SDCARD.
â?¢ Connect your phone in fastboot mode, steps for which are : -
A. Press and hold the Volume Up key
B. With the Volume Up key, connect the phone to your PC/Laptop with USB cable
C. Press volume up to confirm on the first screen.
â?¢ Now you can flash the stock firmware with ygdp tools. (There's plenty of guide for flashing with YGDP tools. Google is your friend)
â?¢ DO NOT disconnect the device during flashing procedure.
â?¢ After the flashing procedure is completed, disconnect the USB cable, remove the microSD card and boot the phone normally by long pressing the Power button.
Your Coolpad Dazen 1 is unbricked now.
Credits:
[email protected] for his thread so I can copy paste some steps from there.
AndroidMTKSite for Stock Rom and Flash Tools
You for trying this guide.
Me for making this guide and creating eMMC backup.
Click to expand...
Click to collapse
Really fantastic work Brother. I was able to revive my phone successfully. Thank you so much for your contribution. Espescially eMMC image.
Hallo Mr zardaman,
I have got 2 Coolpad 8297L-100, which are dead and only shows Qualcomm HS-USB QDloader 9008 driver and no f No Fastboot.
I follow your instruction but do not get success.
It does not come into fastboot mode as well as shows Qualcomm HS-USB QDloader 9008 driver only with sd card(written your file).
Please help...........
Is there any file to flash with QFIL.?????????
my coolpad device got bricked up while i am trying to do flashboot.img now i cant able to swith on it
when ever i try to switch on it, it is saying that download and install the package? this may expose the device to faults and hidden troubles
nothing is happening latter help me to solve this problem
thanks bro thanks you soo much
Hey. i followed the steps correctly. But when using ygdp tool, the flashing got stopped at 72%... now phone is really dead.. there is nothing on the screen now.. when connected to usb the LED lights up for few seconds and bootloader is not showing... It keeps on vibrating when tries to power on.... what do i do..?/? pls help.
We will see here, how we can restore the device Lenovo P8 8703F (wifi) to the factory condition if stucks on the logo or after a brick ...There are several ways , for example ( Qfil, Qpst, eMMC DL, Qcom phone download tool,Qualcomm SW downloader, GNQC etc)
for devices with Qualcomm ,but we will see here an easy way with a tool known as QFIL (recomended) ...Before than all must we have the PC ready, with the appropriate drivers Installed ...
1)Disable driver signature enforcement on Windows 10 permanently/temporarily: a: https://windowsreport.com/driver-signature-enforcement-windows-10/
b: https://www.howtogeek.com/167723/how...igned-drivers/
_ How to disable Driver Signature Enforcement-Video:
(Windows 8, 8.1 & 10)
* _ OR : https://gsmusbdriver.com/fix-driver-signature-error
**(In windows 10,you may need to disable the "secure boot" from BIOS in some cases,before to do this)
( Or, just download this and follow the instructions : https://mega.nz/file/5rphEShJ#-VGvFPM0hZICZC28VQ6zqwHXLA9EEfv_8thiTXla1dY )
2)Qualcomm drivers : https://androiddatahost.com/nbyn6 (how to Install Qualcomm drivers >
)
tutorial & here : https://forum.hovatek.com/thread-16965.html
__Qualcomm drivers (MEGA Cloud) : https://mega.nz/file/0yRDmCYC#e-cadgzqeBcjlO7ThzF148q_dW8i_AATshC35nXbX8Y
__Qualcomm_USB_Driver_1.00.40.5_Setup.exe : https://mega.nz/#!Zq5C3K7A!7I3W9jh79-UbgvJ1dGIYCuj8cbxYtiXAXf4i-mO-VAQ
[Qualcomm usb drivers windows xp,7,8,8.1,10 32bit : https://mega.nz/file/JzAAHBBD#VOlN8HjgFqWfkD8LJafgJxKje18_l6o_vP9gmrja_JU ]
3)_[Important : [Qualcomm HS-USB QDLoader 9008 - Windows XP / 2000 / Vista / 7/8 / 8.1 / 10 x64 : http://www.mediafire.com/file/u3mrk0qan6qz5sq/Qualcomm_USBDriver_2.1.0.5_x64.cab
https://gsmusbdrivers.com/download/qualcomm-hs-usb-qdloader-9008-driver-64-bit-windows/
https://gsmusbdrivers.com/download/qualcomm-hs-usb-qdloader-9008-driver-32-bit-windows/
4) QFIL ALL VERSIONS : https://androidmtk.com/download-qualcomm-flash-image-loader-qfil
5) THE STOCK FIRMWARE Lenovo P8 TB-8703F (wifi) : https://www.mediafire.com/file/nvdo3hq0r6mnoqs/TB-8703F_S000031_170616_ROW_QPST.7z
__MEGA CLOUD : https://mega.nz/#!NipTRSiJ!E5Ej-PWNOllLSfFLla7o_YOTkCkbbLR92Y_aZmMRJYo [FONT=source_sans_proregular](TB-8703F_S000030_170307_ROW_QFIL.7z)[/FONT]
(Source): http://lenovo-forums.ru/files/file/1831-tab3-a8-plus-proshivka-tb-8703f_s000031_170616_row_qpst/
[ For the tools we will use, if a code is requested pass : androidmtk.com / For Stock Firmware pass: lenovo-forums.ru ]
_[* https://firmwarefile.com/lenovo-tb-8703f > (three firmwares tb-8703f USR_S000032/34/35 + tutorials) ]
*For Lenovo P8 TB 8703X (3g-lte) STOCK ROM you can see post #2
__* IMPORTANT ! : Solution to the known problem (sometimes) : " Download Fail:Sahara Fail:QSaharaServer Fail Process fail error" - (Known as the "Sahara Fail Error")
1) disable driver signature ( See the link above )
_ a) Download and try with this version QPST (qfil included) : https://androiddatahost.com/np4wq
_b) Try to another USB port (?) [Try to connect device-pc on usb 2.0 & no on usb 3.0]
_ c) update your drivers : https://gsmusbdrivers.com/download/android-qualcomm-usb-driver/ how to-Quide: https://www.gizmoadvices.com/qualcomm-hs-usb-qdloader-9008-driver/
_d) you must to press power button at the same time you plug in usb cable.....keep trying and your computer will start installing drivers for Port 9008
*_[Maybe you need to Install - update Microsoft NET Framework 4 : https://www.microsoft.com/en-US/download/details.aspx?id=17851
....If you already have instaled, skip this step]
[ The way through Qfil is recommended, has been successfully tested many times by many users & me...Download button will only become active when your device is connected properly! CONNECTED THE DEVICE TO THE COMPUTER BY HOLDING THE VOLUME UP KEY ! Take special care with steps 6,7,8 in tutorial Qfil here ! : https://androidmtk.com/use-qualcomm-flash-image-loader-qfil ....as most mistakes are made here ! Read carefully ....
_Your personal data will be deleted after flashing the stock firmware via Qfil ...
[ Charge your phone to at least 70% before use Qfil ! ]
__ do not hesitate to ask for help from other users , & read carefully before doing anything on your device...
__ please, be kind with everyone ! Tell your opinion freely or your problems for your device etc...
Via QFIL :
1) Download & extract QFIL on your PC...After extracting you will be able to see the Files > Screenshot 1
2)Now,open QFIL.exe > Screenshot 2 (as administrator)
3)Once QFIL is launched you will be able to see the following screen > Screenshot 3
4)Now,Switch OFF your Tablet > Screenshot 7
5)Once your device is Switched OFF, Press & Hold VOLUME UP KEY & CONNECT THE DEVICE TO PC, using USB Cable (attention to this step)
6)Now,in QFIL click on browse button & locate the Firmware (.mbn) > Screenshots 4+5
7)Once you have added the Firmware File, QFIL will automatically load the rest of the Firmware data (qfil detect your device in 9008 mode) > Screenshot 8
8)Now,click on the download button to begin the flashing process > Screenshot 6
9)Flashing process may take 10-15 min to complete (or less)
10)Once flashing process is completed your device will be reboot automatically...thats it , done!
__ All Steps are described & here in detail, read carefully without hurry & everything will be fine : https://androidmtk.com/use-qualcomm-flash-image-loader-qfil
[ QPST (qfil included) ] { https://androiddatahost.com/np4wq } Use this Version QPST if you have problem / error
** "Download Fail:Sahara Fail: QSaharaServer Fail: Process fail error" !
QPST ALL VERSIONS : https://androidmtk.com/download-qpst-flash-tool
Via QPST :
1. Download firmware, drivers and utilities Lenovo Tab P8 TB-8703F (wifi)
2. Unzip the archive contents and install the drivers and QPST utility
3. Run the QFIL utility (included)
4. In the "Select Build Type" set to "Flat Build"
5. Click "Browse" and from the folder with firmware (Images) select the file "prog_emmc_firehose_8953_ddr.mbn"
6. Click "Load XML" and select the file "rawprogram0.XML" and then "patch0.XML"
7. Switch the device off completely
8. Insert one end of the usb cable into the PC, hold down the device buttons to decrease and increase the volume and connect the other end of the usb cable to the device
9. The program must determine the phone, at the top instead of "No Port Available" should appear the name of your device and in brackets the port number (QFIL should detect your device in 9008 mode) > Screenshot 8
10. Press the "Download" button and wait for the operation to be completed
11. After the operation is completed, disconnect the device from the PC and turn it on
12. If everything is done correctly, the device will boot in about few minutes ..(if not, try again, you have made a mistake)
[ before the first start you can try wipe cache-wipe data/factory reset from stock recovery ]
_{ Important! : Press the volume up and plug the USB cable that is already connected to the USB port of your computer without releasing it.! Most mistakes are made here ! the "Qualcomm / Lenovo HS-USB QDLoader 9008" will appear at the top > Screensot 8 }
__Before starts download : Open device Manager in pc & make sure the QFIL program recognizes your device as the "Qualcomm Lenovo HS-USB QDLoader 9008 (com27 for example)" {screenshot 8 }
*[ Recommended: On PC, Latest VC ++ runtime environment / Net 4.0 or higher / Ram at least 2 GB + ]
[ Optionally: _Useful tools ... Lenovo MOTO Smart Assistant / windows7/10, 32&64 bit : https://support.lenovo.com/gr/el/downloads/ds101291
Lenovo site TAB3 8 Plus Tablet (TB-8703F, TB-8703X) Software (connect device-pc) :
https://pcsupport.lenovo.com/gr/el/products/tablets/a-series/tab3-8-plus?linkTrack=Caps:Body_SearchProduct&searchType=3&keyWordSearch=TAB3 8 Plus Tablet (TB-8703F, TB-8703X
_ *Lenovo TB-8703F Usb drivers(Qualcomm & ADB): https://gsmusbdriver.com/lenovo-tab-3-8-plus-tb-8703f
*TB-8703X(Qualcomm&ADB): https://gsmusbdriver.com/lenovo-tab-3-8-plus-tb-8703x
_ Threads about Lenovo P8 xda : https://forum.xda-developers.com/t/lenovo-p8
_ Find various drivers here : https://gsmusbdrivers.com/
_* How to flash stock firmware 8703F/X using QcomDloader Tool : https://androidmtk.com/use-qcomdloader-tool
* stock firmware : 8703F: https://firmwarefile.com/lenovo-tab-3-8-plus-tb-8703f
* 8703X : https://firmwarefile.com/lenovo-tab-3-8-plus-tb-8703x
__ [ Latest TWRP 3.2.3-0308 for TB-8703F & TB-8703X : https://forum.xda-developers.com/android/development/links-t3764658 ]
Lenovo P8 threads: https://forum.xda-developers.com/tags/lenovo-p8/
_[Be careful with the various tools and especially USB drivers, there may be newer versions now, from the time this article was written!]_
( I hope that several users will find help in this thread )
sry for english & GL to all
[ I have no responsibility for what does anyone on his device,nor I can be have responsible for the mistakes done by you]
Lenovo P8 TB 8703X (3g-lte) ONLY!
For the users with Lenovo P8 TB 8703X (3g-lte) ONLY! file TB-8703X_S000034_170525_ROW_QPST.7z
here : http://www.mediafire.com/file/4lg92szdza6coi2/TB-8703X_S000034_170525_ROW_QPST.7z
( pass: lenovo-forums.ru )
TB-8703X_S000036_171207_ROW / 07.12.2017 / 36.5mb - OTA Update! - (Only TB-8703X / 3g-lte) - [TB-8703X_S000035_170919_ROW_TO_TB-8703X_S000036_171207_ROW_WCD2C52B4F.zip
http://www.mediafire.com/file/pqyou...TO_TB-8703X_S000036_171207_ROW_WCD2C52B4F.zip
( pass: lenovo-forums.ru )
[source: http://lenovo-forums.ru/topic/25111...35_170919_row-to-tb-8703x_s000036_171207_row/ ]
__ 21-4-2018 OTA-update for Lenovo P8 TB-8703X (Lte,3g) ONLY! - TB-8703X_S000036_171207_ROW To: TB-8703X_S000037_180404_ROW : mediafire : http://www.mediafire.com/file/3s2bm...TO_TB-8703X_S000037_180404_ROW_WC39DCDC66.zip
(update Via Factory Recovery !)
__* Or, flash stock firmware 8703X using QcomDloader Tool : https://firmwarefile.com/lenovo-tab-3-8-plus-tb-8703x
__ For TWRP 3.2.1-0 & TWRP 3.2.3 Lenovo P8 (F+X) QPST & IMG Files , go to this thread:
https://forum.xda-developers.com/android/development/links-t3764658
__ 4/4/2018 TB-8703X_S000037_180404_ROW :
[MEGA CLOUD] TB-8703X (3g-Lte) - 39.8 Mb
https://mega.nz/file/h2gg1YhK#DkvZqOca0oBHbhViOBNWuHg1ojVZ7SVtprkilI4Fm4k
☆☆__Source : All updates for Lenovo Tab3 TB-8703X (3g-Lte) & Lenovo Tab3 TB-8703F (wifi)
Here : http://lenovo-forums.ru/files/category/152-lenovo-tab3-a8-plus-tb3-8703/
* For the quality - purity of the files I have no responsibility since I am not the developer of the files
Ty sir.. I have no problem until now but I like to have a way to save my device if needed
I'm afraid of the problem with updates .I see many users have the same problem
what does Lenovo for this?
Sonbd said:
Ty sir.. I have no problem until now but I like to have a way to save my device if needed
I'm afraid of the problem with updates .I see many users have the same problem
what does Lenovo for this?
Click to expand...
Click to collapse
Yes is true.I do not know what Lenovo is doing,I don't think he not knows the problem
device perhaps has a problem with bootloader or & recovery also (or maybe with partitions sizes) ..let us hope,Lenovo to fix it,the device has good features & in good price .he policy followed by Lenovo is unacceptable (do not allow unlocking of the bootloader ! )
sry for english
Many Thanks to Assistant Forum Admin / Moderator @ the_scotsman for his help ....Now we have all the device Lenovo P8 threads in a space ,and all users can find what they want very easily !
bravo, good job, man. thanks so much for this post!
i've done this flash thing already. and be careful that your wifi&bluetooth mac address gonna changed.
and also, it's better to backup Qcn file first.
---------- Post added at 10:09 PM ---------- Previous post was at 10:03 PM ----------
oh, there is question, i wanna make a full backup of the stock rom entirely, there is a post about it, https://forum.xda-developers.com/general/rooting-roms/how-to-backup-qualcomm-phone-root-t3570178,
im not pretty sure about the process, have you done it or know how to do it?
not download to the tab, but read from the tab, can qfil do this job?
not download to the tab, but read from the tab, can qfil do this job?[/QUOTE]
Full backup via qfil No! I do not know what he wants to do, but stay away, it is very dangerous all this for hard brick !
For full backup needed or custom recovery (nandroid backup) or rooted device & use some tool from playstore for backup etc..
You can flash twrp : https://forum.xda-developers.com/ge...vo-p8-tb-8703f-tb-8703x-t3689442#post74281359
and after you can get a full nandroid backup ..
except all this, backup for stock rom? and how to restore the backup? also, even if you have the twrp probably will not be able to restore a factory image backup...
sry for english
daitalos said:
not download to the tab, but read from the tab, can qfil do this job?Full backup via qfil No!
Click to expand...
Click to collapse
TB-8703F_S000031_170616_ROW_QPST.7z
I just want to know how is this file dumped or where did the Russians got this file.
Before I downloaded this file into my tablet, I flashed trwp recovery, and made a full backup of the Chinese version ROM . BUT the ORIGINAL lenovo recovery WAS GONE , RIGHT?
SO ..... without the original recovery the backup cannot be called a full backup right
Before I downloaded this file into my tablet, I flashed trwp recovery, and made a full backup of the Chinese version ROM . BUT the ORIGINAL lenovo recovery WAS GONE , RIGHT?
SO ..... without the original recovery the backup cannot be called a full backup right[/QUOTE]
I told you...custom recovery can not flash (or reset) factory image backup (this version twrp decrypt device because Lenovo P8 has a locked bootloader etc..)
backup of stock rom is useless in this device, you can flash stock rom if you want, via Qfil
daitalos said:
If after an ota update the device sticks and it does not start , try it first ! wipe cache - wipe data/factory reset from stock recovery before using Qfil...
In most cases the device starts - boot normally
[ optional - I recommend , Install on your pc this powerful tool : minimal adb & fastboot from here : https://forum.xda-developers.com/showthread.php?t=2317790 & read carefully before Installing ]
For the users with Lenovo P8 TB 8703X (3g-lte) ONLY! file TB-8703X_S000034_170525_ROW_QPST.7z
here : http://www.mediafire.com/file/4lg92szdza6coi2/TB-8703X_S000034_170525_ROW_QPST.7z
Click to expand...
Click to collapse
Hello Friend This File is Password Protected....
need its password Plzz..
Ok i found the password.. the password is " lenovo-forums.ru "
DanishAlnoor said:
Hello Friend This File is Password Protected....
need its password Plzz..
Ok i found the password.. the password is " lenovo-forums.ru "
Click to expand...
Click to collapse
before posting Read first ! keep the thread clean please
Hi to all,
I managed to brick my lenovo TB-8703F after updating Magisk through the TWRP recovery mode.
At first it got into a boot loop and I tried to recover it by flashing the stock rom with the instructions found on this thread.
Unfortunately No luck.....
The tablet was recognized in Qloader Mode and flashed with QFIL but after the flash completed successfully it hanged at lenovo logo boot screen.
Tried wipe data - factory reset without luck.
Now after many attempts with QFIL and different settings it is only recognized in Qualcomm HS-USB Diagnostics 900E mode and cannot be flashed with QFIL, no access to recovery mode, fast boot or anything else....
Do you thing I have a chance of recovering it?
Thanks
panmark said:
Now after many attempts with QFIL and different settings it is only recognized in Qualcomm HS-USB Diagnostics 900E mode and cannot be flashed with QFIL, no access to recovery mode, fast boot or anything else....
Do you thing I have a chance of recovering it?
Thanks
Click to expand...
Click to collapse
Qualcomm drivers are installed correctly; you can try with QPST version from link of OP (Qfil included)
(Disable driver signature?)
daitalos said:
Qualcomm drivers are installed correctly; you can try with QPST version from link of OP (Qfil included)
(Disable driver signature?)
Click to expand...
Click to collapse
Drivers must be OK. (they worked before the hard brick.)
I tried with a deep flash cable but I had no luck.....
Then I opened the case and removed the battery left it for two minutes and tried again. No luck....
I thing I now have a nice paper weight for my office.....
The strange think is that before the hard brick I successfully managed to complete the flashing process for ten or more times but the tablet refused to boot.
panmark said:
Drivers must be OK. (they worked before the hard brick.)
I tried with a deep flash cable but I had no luck.....
Then I opened the case and removed the battery left it for two minutes and tried again. No luck....
I thing I now have a nice paper weight for my office.....
The strange think is that before the hard brick I successfully managed to complete the flashing process for ten or more times but the tablet refused to boot.
Click to expand...
Click to collapse
Does anybody know the test points that have to be shorted in order to force it to connect to EDL 9008 mode?
panmark said:
Does anybody know the test points that have to be shorted in order to force it to connect to EDL 9008 mode?
I've seen it...tools are needed,and there is always a risk of error...I think there is a video with details..
I do not know how much credibility it can be this method....
Click to expand...
Click to collapse
panmark said:
Does anybody know the test points that have to be shorted in order to force it to connect to EDL 9008 mode?
Click to expand...
Click to collapse
Badly translated from Russian
A test point is detected (wi-fi version of the tablet, it may work on lte).
So, install QPST, drivers, download firmware, prepare QFIL for firmware (the instruction is in the subject), when connecting, the brick is defined as HS-USB Diagnostics 900E, disconnect usb cable, disassemble the tablet, turn off the acb, tweeze the pin specified in the photo on the iron frame, hold, do not release the jumper and connect usb, then connect the acb, as soon as the computer determines HS-USB Qdloader 9008
release the jumper and click download in QFIL.
Click to expand...
Click to collapse
obvious said:
Badly translated from Russian
Click to expand...
Click to collapse
thanks!!!!
I will give it a try and lets you know!
---------- Post added at 08:46 PM ---------- Previous post was at 08:41 PM ----------
panmark said:
thanks!!!!
I will give it a try and lets you know!
Click to expand...
Click to collapse
It Works!!!!!!!!!!!
Thanks!!!!!
Know back to QFIL.
---------- Post added at 08:59 PM ---------- Previous post was at 08:46 PM ----------
panmark said:
thanks!!!!
I will give it a try and lets you know!
---------- Post added at 08:46 PM ---------- Previous post was at 08:41 PM ----------
It Works!!!!!!!!!!!
Thanks!!!!!
Know back to QFIL.
Click to expand...
Click to collapse
Flashed Successfully with QSTP (QFIL) according to the instructions!!!!!!
You are the man my friend!!!!!!!
panmark said:
thanks!!!!
I will give it a try and lets you know!
---------- Post added at 08:46 PM ---------- Previous post was at 08:41 PM ----------
It Works!!!!!!!!!!!
Thanks!!!!!
Know back to QFIL.
---------- Post added at 08:59 PM ---------- Previous post was at 08:46 PM ----------
Flashed Successfully with QSTP (QFIL) according to the instructions!!!!!!
You are the man my friend!!!!!!!
Click to expand...
Click to collapse
Haha, I'm glad it worked
panmark said:
thanks!!!!
I will give it a try and lets you know!
---------- Post added at 08:46 PM ---------- Previous post was at 08:41 PM ----------
It Works!!!!!!!!!!!
Thanks!!!!!
Know back to QFIL.
---------- Post added at 08:59 PM ---------- Previous post was at 08:46 PM ----------
Flashed Successfully with QSTP (QFIL) according to the instructions!!!!!!
You are the man my friend!!!!!!!
Click to expand...
Click to collapse
I post a better quality photo for everyone