Related
Hi guys, first of, i want to thank the one who made the thread on how to uninstall SuperUSer using terminal apk with codes.
that was my 1st problem on how to remove that SU. 2nd is on how to reflash my LM me p350 software.
i followed the instructions.
How to flash LG Optimus Me Steps:
1. Install the USB drivers and LG B2C Tools
2. Unzip KDZ_FW_UPD_EN.7z and installed msxml.msi
3) Shut down the LG Optimus Me, remove the battery and connect the USB cable holding down the Volume Up button and wait until the drivers are installed (the phone should be on the "S/W upgrade Please wait" state while upgrading!!!!)
or
3′. Enable USB debugging and connect USB cable to your LG Optimus Me
4. Open your device manager and disabled under the Modem LGE Mobile USB Modem
5. Starts KDZ_FW_UPD.exe
6. In the Software Updater select "Type"=CDMA , "PhoneMode"=DIAG, and at "KDZ file" select the desired file. (The firmware .kdz file must have the name in this form!)
This will open "Read phone information" window. IN THAT WINDOW:
7. Click "Upgrade start". DO NOT CLICK ANYTHING ELSE BEFORE!
LG Updater launches…..
8. Select Country="Different country" (unless you are in Korea) and Language as you wish
LG Mobile Updater Launches………. warning you and asking your permission to continue..
9. Follow LG Mobile Updater instructions…
Let the tool running for a few minutes through and be pacient!!
ATTENTION!!
After the phone reboots first time, DO NOT UNPLUG USB CABLE!!!
WAIT!! Remove USB cable only after the log says that the flash was OK!
10. The flashing process is now finished.
i downloaded the V10F although mine is V10B Feb 22,2011.
i'm good to go, and i'm on #7, unpacking KDZ, and then Cannot find PHONE!
before that, when i plugged my phone and used usb debugging, there's now the big problem that's why the updater didnt detect the phone because of this : "Unable to install Driver Software".
How can i fix this problem, for me to flash my phone, i can't flash it if my PC/laptop can't detect my phone.
i would really appreciate a quick help. LG service center here is 4 hour road trip. back and forth hat would be 8 hours. so i'll ask for help first here. thanks.
Please some quick help about this, i've search about this but no clear guides we're given, i've installed the possible USB drivers for my PC laptop to read my LG me, but none of them worked.
Follow this guide carefully and you can revive your dead Karbonn A9+/ CM Flare after Jelly Bean Upgrade.
Tools Needed:
Dead Phone (When u connect to PC it should install Qualcomm HS-USB QD Loader 9008 Driver) Link
QPST.2.7.399 Link
Flare Revival kit Link
PC with 32 bit Windows (XP/Vista/7/8) (64bit casus problem in QPST installation)
Credit goes to jhanra for the tutorial as well as CWM 6.0.1.1 for JB ROM . :good:
Procedure
Connect ur phone to PC and let the driver install
Install QPST
Open QPST Configuration (in Win XP compatibility mode) ->Add new port -> Select the com port of your device ->exit.
Go to Start -> All Programs -> QPST eMMC Software Download open the tool -> Check program boot loaders -> Browse for the device com port
Extract Flare Revival Kit on desktop
If Phone is not detected , Click Browse
In flash programmer file name type MPRG8X25.hex -> in Boot Image type 8X25_msimage.mbn in SPC ->000000
Click Load XML def and browse for rawprogram0.xml in Flare Revival Kit
Click Load Patch def and browse for patch0.xml
Check the search path 2 and browse for the folder flare repair files
Now click download, wait for the download to finish (it never finish but it also detects for a new driver, and that’s important) and it will search for the new hardware found, install the driver
From here you can updating your rom to jelly bean using this tutorial Link
Guys, anyone encountering "Cookie (if present) not received" error after clicking on Download button?
My Karbonn A9+ as successfully updated to jelly bean, which was working flawlessly for 3 days. But suddenly it died while my charging my phone.. The phone could not be turned on, no fastloader or entry download mode.... However when connected to PC it was being detected as Qualcomm HS-USB QD Loader 9008. I tried this tutorial but am facing cookie not received error.
Since my phone died suddenly, not during any update firmware process... I suspect this could be case of Sudden Death Syndrome (SDS) which means my eMMC flash (internal storage) got corrupted and is not being able to recoginized by QPST tool.
Has anyone faced this problem?
kornholic said:
Guys, anyone encountering "Cookie (if present) not received" error after clicking on Download button?
My Karbonn A9+ as successfully updated to jelly bean, which was working flawlessly for 3 days. But suddenly it died while my charging my phone.. The phone could not be turned on, no fastloader or entry download mode.... However when connected to PC it was being detected as Qualcomm HS-USB QD Loader 9008. I tried this tutorial but am facing cookie not received error.
Since my phone died suddenly, not during any update firmware process... I suspect this could be case of Sudden Death Syndrome (SDS) which means my eMMC flash (internal storage) got corrupted and is not being able to recoginized by QPST tool.
Has anyone faced this problem?
Click to expand...
Click to collapse
Please state your OS Win XP or 7. Try using 32 bit win XP PC.
arunmcops said:
Please state your OS Win XP or 7. Try using 32 bit win XP PC.
Click to expand...
Click to collapse
My os is windows 7 32 bit.. i tried running emmc downloader with windows xp compatibility mode also. same problem.
kornholic said:
My os is windows 7 32 bit.. i tried running emmc downloader with windows xp compatibility mode also. same problem.
Click to expand...
Click to collapse
QPST caused me problems with Win 7. I used win XP.
arunmcops said:
QPST caused me problems with Win 7. I used win XP.
Click to expand...
Click to collapse
Tried it on Win XP... same cookie(if present) not received error showing..
can we use vmplayer for the win xp or other virtual soever instead? i use win 8 64 bit that's why it won't able me to download and shows me the message that the cookie (if present) is not received. :angel::angel::angel:
Some from a chinese forum was able to fix the cookie problem through QFPROM Fuse..
http:// lepad.it168.com/thread-2920933-1-1.html
(its in chinese)
What does it mean?
kornholic said:
Some from a chinese forum was able to fix the cookie problem through QFPROM Fuse..
http:// lepad.it168.com/thread-2920933-1-1.html
(its in chinese)
What does it mean?
Click to expand...
Click to collapse
Only explanation given is that This problem is related to specific PC.
arunmcops said:
Only explanation given is that This problem is related to specific PC.
Click to expand...
Click to collapse
Yes the person in one post first said the problem is due to PC and driver combination. However, in later post has also said:
"i am still stuck in download mode. i was able to programm the bootloader, as i mentioned before by using QFPROM Fuse, everything else leads to errors. only one little detail changed -> when i press the power button it vibrates shortly.when i try to porgram the mmc device i always get no response from the phone."
Some of the points to ponder are:
1. He said he was able to program bootloader using qfprom fuse.
(How did he program bootloader through qfprom fuse, what does this mean?)
2. When power button pressed, there is vibration...
(On my device there is no response when pressed on power on.)
3. However he later said when he tries to program mm, he gets no response.
(He has not said he gets cookie error, just not response... could be anything)
one of the moderator of cherry flare group at facebook was able to revive phone from cookie error.
check http://www.youtube.com/watch?v=qHQIIsqV1Zw
i just found out that you can restore your phone too by using roadkill, if you had written the backup of the image of your phone lately. :angel:
heyyanyan said:
i just found out that you can restore your phone too by using roadkill, if you had written the backup of the image of your phone lately. :angel:
Click to expand...
Click to collapse
yes, if you could access entry qpst download mode (vol down + power)... however if you are hard bricked... you would not be able to access that plus your phone would not turn on in any manner.
in my case, my phone didn't turn on no matter what i do. but if i connect my phone to the pc, it shows the qualcomm hs-usb something that can be read by roadkill.
heyyanyan said:
in my case, my phone didn't turn on no matter what i do. but if i connect my phone to the pc, it shows the qualcomm hs-usb something that can be read by roadkill.
Click to expand...
Click to collapse
did you manage to fix your phone?? ......................................................
arunmcops said:
Connect ur phone to PC and let the driver install
Install QPST
Open QPST Configuration (in Win XP compatibility mode) ->Add new port -> Select the com port of your device ->exit.
Go to Start -> All Programs -> QPST eMMC Software Download open the tool -> Check program boot loaders -> Browse for the device com port
Extract Flare Revival Kit on desktop
If Phone is not detected , Click Browse
In flash programmer file name type MPRG8X25.hex -> in Boot Image type 8X25_msimage.mbn in SPC ->000000
Click Load XML def and browse for rawprogram0.xml in Flare Revival Kit
Click Load Patch def and browse for patch0.xml
Check the search path 2 and browse for the folder flare repair files
Now click download, wait for the download to finish (it never finish but it also detects for a new driver, and that’s important) and it will search for the new hardware found, install the driver
From here you can updating your rom to jelly bean using this tutorial Link
Click to expand...
Click to collapse
!!!
!? I just Ported CWM 6.0.1.1 to CM Flare Jelly bean (for JELLY BEAN ONLY)!! !!!! I Already test it with my own 3pcs CM FLARE phone with no problem! In porting this CWM my 2 phone died porting this CWM but I recover it WITH THIS METHOD you posted!!!!!!!!!!!!!!
FLash this with AIO FLASHER
check recovery erase then flash
View attachment 2089726
theres nothing it can do if you try it? it cannot mess your phone!
!!!
this is the full tutorial for this! View attachment 2089809,
and this is the file for this case!
h ttp://www.4shared.co m/rar/rzVTMMxY/flare_repair_files.html
after this you can flash BP firmware in this! follow the tut in flashing BP Firmware and so on
to upgrading in jelly bean BY ARUNMCOPS! here ht tp://forum. xda-developers.com/ showthread.php?t=2330823
the original thread is here ht tp://www.pinoy den.com.ph/inde x.php?topic=274677.0
Note: just erase the spaces of the link!
you can try the steps on my tut but DO THIS AT YOUR OWN RISK!!!
!!!!!!
[email protected]@@
[MENTION=1065870 [user=1879310]@@@@[/user][/MENTION]
@@@
kornholic
@@@????
Hello , after alot of research online I've managed to come up with a way to unbrick my hard bricked device Sky IM-A770K in qhsusb_dload mode with dead boot ,without having to send it to those jtag/medusa services with the help of some methods i found on some vietnames websites . Ok so before we begin I hold no responsibility for the damage that you're device gets so follow the steps exactly as I say .
So this is the ultimate guide to unbrick your IM-A770K or IM-A760S device from qhs_usbdload. :fingers-crossed:
Note : This guide works only for devices stuck in QHS_usbdload mode.(No boot)
(Note: in the links remove blank spaces.)
Note windows 7 is recommended OS to have on this guide :
1. Download the attached files in the link at the end of thread.
1.5.Open cmd in administrator mode and type
Code:
bcdedit /set {globalsettings} advancedoptions true
1.6.Restart Pc and disable driver signature enforcement.
2. Connect sky im a770k to pc with usb.
3. Open device manager. Device should should show as qhsusb_dload.
4.Click on device and click update driver browse for the files qhs_usbdload and chose the driver accordingly to 32bit or 64bit system.
5.Once drivers installed the device should show as Qualcomm Usb Diagnostic 9006 (COMx)(Note: x stands for the number of the port of your device that your pc shows).
6.Install qpst.
7.Open Qpst Configuration , Select Ports->Add New Port -> Select (COMx) of your phone you can check it at device manager.
8.Close. Open emmc Software download.
9. Check the image 'emmc Software download' in the files i've provided for configuration click download.
10. Now your device should show as Qualcom cdma technologies msm in device manager.
10.5 Click on it Update Drivers browse for file select the drivers from the files that i've provided you with . Its qualcom cdma technologies.
10.6.Now you'r device should show in device manager as qualcom diagnostic mode 9025 or 9008.
11. If asked do not format. If device boots up do not attempt the following.You've fixed it . If not continue with below steps.
12.This is the hard part you should be careful with this could damage your internal emmc partitions permanently.
13. Install winHex from winhex folder.
14.Open winhex as administrator.
14.5.Warning this step is for sky im a770k or 760s only if you have another device please do not attempt it as you may damage emmc(sdcard) permanently. Thank You.
15. Select File->Restore Image->Browse to the downloaded files of my guide(Change File type to .01,.img,etc)->Select unbrick770k760s.img. Open.
16. Select Kind of image: Disk.
17.Select Target Disk At Logical Volumes /Partitions Your device should show as qualcom msm 14.9gb (something like that) chose it. WARNING do not chose other drives as they could be damaged.
18. Click ok . And wait till it's finished.
19. Your device should boot up If you followed the steps correctly.
20.Hope this fixes it.
Next all you have to do is flash firmware offline check out this guy do as he does.Or you can google other ways:
htt ps://ww w.you tube.com/watch?v=uDsOm orfp0I
Again I do not hold responsibility for all the above steps . It worked for me maybe it'll work for you or your device could be damaged more who knows so do this on your own risk. If you chose to do this be sure to install the drivers properly. Research on how to install them if you're having trouble doing it .If this methods doesn't work for you keep researching online maybe you'll find a way.It took me a week of research before i could come up with this. For any questions you have you can ask me.
Thank you And Good Luck! :good:
Download Files:
htt ps://drive.go ogle.com/file/d/0B4r0yxK Mlkspa FQ5 cE1QUzR ObDA/view ?usp=sharing
Hello Sir,
Congratulations on unbricking phone. I am having similar problem with my IM-A860L and I am not able to find appropriate files for my device. Can you please help? I have also opened a help thread here: https://forum.xda-developers.com/general/help/help-bricked-im-a860l-pantech-vega-6-t3639621
Please help!
help needed
Aster95 said:
Hello , after alot of research online I've managed to come up with a way to unbrick my hard bricked device Sky IM-A770K in qhsusb_dload mode with dead boot ,without having to send it to those jtag/medusa services with the help of some methods i found on some vietnames websites . Ok so before we begin I hold no responsibility for the damage that you're device gets so follow the steps exactly as I say .
So this is the ultimate guide to unbrick your IM-A770K or IM-A760S device from qhs_usbdload. :fingers-crossed:
Note : This guide works only for devices stuck in QHS_usbdload mode.(No boot)
(Note: in the links remove blank spaces.)
Note windows 7 is recommended OS to have on this guide :
1. Download the attached files in the link at the end of thread.
1.5.Open cmd in administrator mode and type
Code:
bcdedit /set {globalsettings} advancedoptions true
1.6.Restart Pc and disable driver signature enforcement.
2. Connect sky im a770k to pc with usb.
3. Open device manager. Device should should show as qhsusb_dload.
4.Click on device and click update driver browse for the files qhs_usbdload and chose the driver accordingly to 32bit or 64bit system.
5.Once drivers installed the device should show as Qualcomm Usb Diagnostic 9006 (COMx)(Note: x stands for the number of the port of your device that your pc shows).
6.Install qpst.
7.Open Qpst Configuration , Select Ports->Add New Port -> Select (COMx) of your phone you can check it at device manager.
8.Close. Open emmc Software download.
9. Check the image 'emmc Software download' in the files i've provided for configuration click download.
10. Now your device should show as Qualcom cdma technologies msm in device manager.
10.5 Click on it Update Drivers browse for file select the drivers from the files that i've provided you with . Its qualcom cdma technologies.
10.6.Now you'r device should show in device manager as qualcom diagnostic mode 9025 or 9008.
11. If asked do not format. If device boots up do not attempt the following.You've fixed it . If not continue with below steps.
12.This is the hard part you should be careful with this could damage your internal emmc partitions permanently.
13. Install winHex from winhex folder.
14.Open winhex as administrator.
14.5.Warning this step is for sky im a770k or 760s only if you have another device please do not attempt it as you may damage emmc(sdcard) permanently. Thank You.
15. Select File->Restore Image->Browse to the downloaded files of my guide(Change File type to .01,.img,etc)->Select unbrick770k760s.img. Open.
16. Select Kind of image: Disk.
17.Select Target Disk At Logical Volumes /Partitions Your device should show as qualcom msm 14.9gb (something like that) chose it. WARNING do not chose other drives as they could be damaged.
18. Click ok . And wait till it's finished.
19. Your device should boot up If you followed the steps correctly.
20.Hope this fixes it.
Next all you have to do is flash firmware offline check out this guy do as he does.Or you can google other ways:
htt ps://ww w.you tube.com/watch?v=uDsOm orfp0I
Again I do not hold responsibility for all the above steps . It worked for me maybe it'll work for you or your device could be damaged more who knows so do this on your own risk. If you chose to do this be sure to install the drivers properly. Research on how to install them if you're having trouble doing it .If this methods doesn't work for you keep researching online maybe you'll find a way.It took me a week of research before i could come up with this. For any questions you have you can ask me.
Thank you And Good Luck! :good:
Download Files:
htt ps://drive.go ogle.com/file/d/0B4r0yxK Mlkspa FQ5 cE1QUzR ObDA/view ?usp=sharing
Click to expand...
Click to collapse
please can you give me the Korean site addresses i want A870L Qpts files in .hex and mnf files.
if you can provide please help me in this matter
[GUIDE][K920] CM / BootLoop / Error > QFIL Flash > Lenovo Vibe Z2 Pro Stock 5.0.2
How to revert back: "CyanogenMod > QFIL Flash > Lenovo Stock 5.0.2 K920_S288_160224_ROW"
(Or last save from: "BootLoop/Error > QFIL Flash > Lenovo Stock 5.0.2 K920_S288_160224_ROW")
!!! Warning: You will lose all your data not backed up before flashing firmware !!!
! I am not responsible for bricked devices, everything what you do is at your own risk !
! This will also relock Bootloader, restore Stock Recovery, remove ROOT and format Internal Storage !
Installation instructions QPST firmware using QFile Flash:
1 - Install the necessary drivers ("ADB Drivers", "Lenovo USB Drivers" and "Qualcomm USB drivers")
2 - Activate the "Developer" menu on your phone settings (10x Double-click "Build number" in the "Settings>About Phone")
3 - Enable the "Debug Android" in the "Settings>Developer"
4 - Connect your phone to your computer using a USB cable
5 - Wait until Windows installs a device driver (this may take a while)
6 - When you connect your phone to your computer confirm the "Always allow from this computer" if the message appears
7 - Unplug the USB cable and turn off the phone (after installing the drivers)
8 - Install "QPST_2.7.422" tool
9 - Run the installed program "QFIL" ("Start>All Applications>QPST>QFIL" (Windows 10))
10 - Press and hold the "Volume +" button and connect the USB cable to the switched off phone (will switch to service mode which allows installation/reinstallation Qualcomm drivers)
Will be displayed at the top of the bar in the "QFIL" following information "HS-USB QDLoader 9008 (COM XX)" instead of the original "No Port Avaiable" announcement
11 - After installing the drivers release the "Volume +" and let the phone reboot himself
12 - Verify the correct installation of the drivers in the "Device Manager" on your computer, it needs to have the following items:
"Lenovo Composite ADB Interface" under ADB Android Device, "Lenovo HS-USB Modem Phone" under Modem, "Lenovo HS-USB Diagnostics" and "Lenovo HS-USB NMEA" under COM/LPT ports.
If you see such headings you have all the necessary drivers installed, disconnect the phone from the USB cable and then switch off
13 - Unzip the downloaded file "K920_S288_160224_ROW_QFIL.rar" and copy the entire contents of the folder to "C:/"
14 - In the program "QFIL" fill for "Programmer patch" by select "Browse>prog_emmc_firehose_8974.mbn" from "K920_S288_160224_ROW_QFIL\SW"
15 - Under "RawProgram" select "Load XML>rawprogram0.xml"
16 - Following the "Patch" select "Select patch file>patch0.xml"
The result should look like in the picture below ...
17 - Now again press and hold the "Volume +" and connect the USB cable to the switched off phone
18 - In the moment when when you see in the "QFIL" at the top bar notification "Qualcomm HS-USB QDLoader 9008 (COM XX)" you must immediately start the firmware upgrade by selecting "Download" until cca 3 seconds and then release the "Volume" button, when nothing happened, repeat step again from a point 17
19 - Wait for the process is complete (about 2-5 minutes) then after restarting the phone disconnect the USB cable
20 - If everything went smoothly you now have the original "Lenovo K920_S288_160224_ROW" firmware on your phone
Files for download:
K920_S288_160224_ROW_QFIL.rar Source lenovo-forums.ru by "kraminski" (MD5:596739b6303d8d25d1ed9202daae157c)
ADB-Driver-v1.4.2.zip + LenovoUsbDriver_1.0.12.exe + Qualcomm_USB_Drivers.zip Source forum.xda-developers.com by "Electry"
QPST_2.7.422.zip (MD5:a9ebd8ab2b2bb08b3d4a19419c9b120e)
Reserved
Hi
do phone have to have cm12.1 rom when following these instructions, or can it be any rom?
No matter what the ROM or an Android version is used on phone.
But remember that all DATA on all partition will be deleted (Internal Storage include)!!!
Make backup of everything important before you will start...
c.x
cant install quallcomm driver to win 10, probably therefore QFIL say "no port available"?
Which version of WIN10 do you use? 32bit or 64bit?
Click on the "*.inf" file in the "Qualcomm_USB_Drivers\Checked" directory and choose "Install"
Otherwise, QFIL always shows "No port available" until you connect phone into USB port and wait for install all necessary drivers...
c.x
thanks
I have win10 32bit. I tried to do like u said, but it gives me error "a problem was encountered while attempting to add the driver to the store"
There are 3 install files, choose every file in directory "Qualcomm_USB_Drivers\Checked\x86" or "Qualcomm_USB_Drivers\Free\x86" (qcmdm.inf, qcser.inf and qcnet.inf). You have to be login as Administrator in WIN10.
What happen when you connect your phone and run "QFIL"?
(I mean like in step: 10 - Press and hold the "Volume +" button and connect the USB cable to the switched off phone (will switch to service mode which allows installation/reinstallation Qualcomm drivers))
c.x
clone.x said:
There are 3 install files, choose every file in directory "Qualcomm_USB_Drivers\Checked\x86" or "Qualcomm_USB_Drivers\Free\x86" (qcmdm.inf, qcser.inf and qcnet.inf). You have to be login as Administrator in WIN10.
What happen when you connect your phone and run "QFIL"?
(I mean like in step: 10 - Press and hold the "Volume +" button and connect the USB cable to the switched off phone (will switch to service mode which allows installation/reinstallation Qualcomm drivers))
c.x
Click to expand...
Click to collapse
Im logged in as admin, i tried to install all of them, "Qualcomm_USB_Drivers\Checked\x86" and "Qualcomm_USB_Drivers\Free\x86" , still same error.
when i connect my phone holding vol+ , QFIL say "Qualcomm HS-USB QDLoader 9008 (COM4)" and after few seconds phone vibrates and say "No Port Available" and then after few seconds it starts again with "Qualcomm HS-USB QDLoader 9008 (COM4)"........ keeps repeating.
not sure if it helps, but i will try another pc tomorrow
That's all right! You have already installed drivers on your PC, now you can continue with my guide from step 13.
Good luck, mate!
c.x
clone.x said:
That's all right! You have already installed drivers on your PC, now you can continue with my guide from step 13.
Good luck, mate!
c.x
Click to expand...
Click to collapse
heh, ok... stupid me
thanks a lot for instructions, u saved me :good: appreciate your work
all the best
You are welcome... :good:
c.x
mate my phone is dead, i can only see lenovo logo, cant access recovery mode,will this work for me,i mean when i cant access usb debugging in setting.
If the QFIL utility can recognize your phone in service mode and you have installed the all necessary drivers then it will work...
You can try it and write result.
c.x
So i'm here too, my vibe 2 dies when installing last android update OTA, i didn't root, unlock or install any custom roms, now i can enter in some recovery menu and some test menu, i read your install guide but i don't know where to start, i have a brand new win10 32bit and the phone never been connected to the pc, so there is no lenovo drivers on it, my question is can i use your guide to reinstall official lenovo firmware ? and steps will be very useful.
Thanks!
MAdbUSU said:
So i'm here too, my vibe 2 dies when installing last android update OTA, i didn't root, unlock or install any custom roms, now i can enter in some recovery menu and some test menu, i read your install guide but i don't know where to start, i have a brand new win10 32bit and the phone never been connected to the pc, so there is no lenovo drivers on it, my question is can i use your guide to reinstall official lenovo firmware ? and steps will be very useful.
Thanks!
Click to expand...
Click to collapse
so i flash the stock firmware, i'm not sure if i understand well step 19.
when flash complete and phone reboots himself i remove the usb cable from pc
the QFIL give me this message i will attach a screenshot, and i'm not sure if the flash process completes well ?
I really need an answer guys, i already flash 3 times the stock ROM thru QFIL, every time i got the message posted above, i'm not sure if it's ok???
The problem is after flashing the stock rom ....phone start ... i can configure the google account then phone reboots and got the blue screen the phone vibrates .
I don't know what to do at this point or what i'm doing wrong here.... any advice it's welcome, thank you guys.
My problem is littel bit other.
The same problem as was mentioned few posts before
when i connect my phone holding vol+ , QFIL say "Qualcomm HS-USB QDLoader 9008 (COM9)" and after few seconds phone vibrates and say "No Port Available" and then after few seconds it starts again with "Qualcomm HS-USB QDLoader 9008 (COM9)"........ keeps repeating.
When I tried to press Download I received this message:
Code:
Start Download
Program Path:C:\Lenovo K920\K920_S246_150520_ROW_qpst\prog_emmc_firehose_8974.mbn
COM Port number:9
Sahara Connecting ...
Download Fail:QC.QMSLPhone.PhoneException: Could not connect to the COMPORT
at QC.QMSLPhone.Phone.ConnectToServer_Sahara(UInt32 comPort, UInt64& version, Int32 mode, UInt64 timeout)
at QC.SwDownloadDLL.SwDownload.QPHONEMSSaharaDownloadArmPrg(UInt64& version, String armPrgPath)
Download Fail:Sahara FailValue cannot be null.
Parameter name: key
Finish Download
I am on Windows 10 64bit - K920 was bought in Slovakia
Please any suggestion?
clone.x said:
How to revert back: "CyanogenMod > QFIL Flash > Lenovo Stock 5.0.2 K920_S246_150520_ROW"
(Or last save from: "BootLoop/Error > QFIL Flash > Lenovo Stock 5.0.2 K920_S246_150520_ROW")
!!! Warning: You will lose all your data not backed up before flashing firmware !!!
! I am not responsible for bricked devices, everything what you do is at your own risk !
! This will also relock Bootloader, restore Stock Recovery, remove ROOT and format Internal Storage !
Installation instructions QPST firmware using QFile Flash:
1 - Install the necessary drivers ("ADB Drivers", "Lenovo USB Drivers" and "Qualcomm USB drivers")
2 - Activate the "Developer" menu on your phone settings (10x Double-click "Build number" in the "Settings>About Phone")
3 - Enable the "Debug Android" in the "Settings>Developer"
4 - Connect your phone to your computer using a USB cable
5 - Wait until Windows installs a device driver (this may take a while)
6 - When you connect your phone to your computer confirm the "Always allow from this computer" if the message appears
7 - Unplug the USB cable and turn off the phone (after installing the drivers)
8 - Install "QPST_2.7.422" tool
9 - Run the installed program "QFIL" ("Start>All Applications>QPST>QFIL" (Windows 10))
10 - Press and hold the "Volume +" button and connect the USB cable to the switched off phone (will switch to service mode which allows installation/reinstallation Qualcomm drivers)
Will be displayed at the top of the bar in the "QFIL" following information "HS-USB QDLoader 9008 (COM XX)" instead of the original "No Port Avaiable" announcement
11 - After installing the drivers release the "Volume +" and let the phone reboot himself
12 - Verify the correct installation of the drivers in the "Device Manager" on your computer, it needs to have the following items:
"Lenovo Composite ADB Interface" under ADB Android Device, "Lenovo HS-USB Modem Phone" under Modem, "Lenovo HS-USB Diagnostics" and "Lenovo HS-USB NMEA" under COM/LPT ports.
If you see such headings you have all the necessary drivers installed, disconnect the phone from the USB cable and then switch off
13 - Unzip the downloaded file "K920_S246_150520_ROW_qpst.7z" and copy the entire contents of the folder to "C:/"
14 - In the program "QFIL" fill for "Programmer patch" by select "Browse>prog_emmc_firehose_8974.mbn" from "K920_S246_150520_ROW_qpst"
15 - Under "RawProgram" select "Load XML>rawprogram0.xml"
16 - Following the "Patch" select "Select patch file>patch0.xml"
The result should look like in the picture below ...
17 - Now again press and hold the "Volume +" and connect the USB cable to the switched off phone
18 - In the moment when when you see in the "QFIL" at the top bar notification "Qualcomm HS-USB QDLoader 9008 (COM XX)" you must immediately start the firmware upgrade by selecting "Download" until cca 3 seconds and then release the "Volume" button, when nothing happened, repeat step again from a point 17
19 - Wait for the process is complete (about 2-5 minutes) then after restarting the phone disconnect the USB cable
20 - If everything went smoothly you now have the original "Lenovo 5.0.2 Stock K920_S246_150520_ROW" firmware on your phone
Files for download:
K920_S246_150520_ROW_qpst.7z Source lenovo-forums.ru by "kraminski" (MD5:5c0cea13f43dac560b68cb1a15be8020)
ADB-Driver-v1.4.2.zip + LenovoUsbDriver_1.0.12.exe + Qualcomm_USB_Drivers.zip Source forum.xda-developers.com by "Electry"
QPST_2.7.422.zip (MD5:a9ebd8ab2b2bb08b3d4a19419c9b120e)
Click to expand...
Click to collapse
This helped me to recover my soft-bricked K920 back to Live!!!
1st time with subsequent 3 updates to S288 ROW but since ROW i didnt not get any signal and SIM error.
2nd time, replaced with CN modem file, detected 4G/LTE but it gone after OTA update for 2nd/3rd/4th times..
3rd time, replaced with CN modem file and stopped the OTA..works fine till now but weird I do not see System Update features anymore..
HOW TO SOLVE SWIPE ELITE PLUS OR ANY ANDROID BRICK AFTER FLASH.
THIS WORKS IN SWIPE ELITE PLUS
if your phone is not starting ,not even go in recovery mode ,fast boot,.
SOlution-
#first connect your phone to the pc or laptop .
If your phone is connected with pc showing multiple drives in pc. (5-6) drives Then dont worry You can
rebirth your phone.
1.first download the diskgenius latest version in your pc .( LINK here )
2-Open diskgenius where you can see multiple drives
- in the Device Manager (Windows) will be Qualcomm HS-USB QDLoader 9006 (COMx ) - or (the driver installed in your phone)
if not, click the + and - volume, along with the power button, the appearance, let go first and then the power and volume buttons.
If you do not appear, it means you have not installed drivers Qualcomm (in the cap is, install)
- run DiskGenius (be careful! You get access to all the connected drives, do not remove too much!))
- Delete partitions SBL1 (Right-click to select the recycle symbol ), confirm the removal (Yes) to apply your changes
(the first icon in the menu, vaguely reminiscent of the character Commander floppy or Total).
3-disconnected and reconnected body to USB, and lo and behold - found new hardware,
Windows itself installs the necessary drivers. In Device Manager,
we see Qualcomm HS-USB QDLoader 9008 (COMx) or (phone driver)
4-THEN open your flash file Tool( QFIL )
in QFIL OPEN YOUR PROGRAM FILE THEN FLASH YOUR PHONE W8 UNTIL ITS WILL FLASH
AFTER FLASHING COMPLETE DISCCONNECT CABLE AND RESTART YOUR PHONE
watch my video swipe elite dead
any QUERRY COMMENT BELOW