Okay so i just got my replacement today, upgraded to JB and now when i try to flash anything with odin it fails at nand write.
Show for odin status
<OSM> All threads completed. (succeed 0 / failed 0)
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> 7z¼¯'
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
CovXX said:
Okay so i just got my replacement today, upgraded to JB and now when i try to flash anything with odin it fails at nand write.
Show for odin status
<OSM> All threads completed. (succeed 0 / failed 0)
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> 7z¼¯'
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
From what I have seen in ODIN none of this is right. Added should be 1rst line. Whole script line looks bad to me. Can't tell what you are doing. May need to PM me to avoid a brick.
---------- Post added at 02:48 AM ---------- Previous post was at 02:46 AM ----------
Since post was yesterday Mod may want to close this one. He got it or bricked it. :laugh:
nope didn't get it and isnt bricked either. Tryed again
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> VRBLK3_Bootchain_CWM.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> recovery.img
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
Saw the updated instructions just hours after I posted that. Everything is up and running great!
***********************************
Oh funny I ran across this tread. I just bought an s3 off contract, did the OTA update, and now it seems I can't get root or figure out even what I am doing wrong.
I have spent the better part of a day, bouncing between 3 computers and 4 software environments trying to get all the different guides I have found off of here to work. I have used the toolkit which I realizes states that you must have unlocked bootloader. I try to unlock bootloader, which the instructions seem to suggest that you must root first, I can't get any sort of file permissions to write root files. tried 3 different guides, all at the top of the forum lists.
Below is what I get when I try to flash file in odin per root instructions in tool kit:
*********
<ID:0/005> Removed!!
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> boot.img
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!
jerrt010 said:
Saw the updated instructions just hours after I posted that. Everything is up and running great!
***********************************
Oh funny I ran across this tread. I just bought an s3 off contract, did the OTA update, and now it seems I can't get root or figure out even what I am doing wrong.
I have spent the better part of a day, bouncing between 3 computers and 4 software environments trying to get all the different guides I have found off of here to work. I have used the toolkit which I realizes states that you must have unlocked bootloader. I try to unlock bootloader, which the instructions seem to suggest that you must root first, I can't get any sort of file permissions to write root files. tried 3 different guides, all at the top of the forum lists.
Below is what I get when I try to flash file in odin per root instructions in tool kit:
*********
<ID:0/005> Removed!!
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> boot.img
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!
Click to expand...
Click to collapse
Updated instructions where? I keep getting the same thing. How did you fix it?
Where did you get the updated instructions? Please Tell
Sent from my SCH-I535 using xda app-developers app
so i downloaded the 4.4.2 firmware i did all the steps with odin.. and i keep getting this
<OSM> Please wait..
<OSM> G900A_Downgrade_to_NCE.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1005)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> boot.img
<ID:0/003> NAND Write Start!!
<ID:0/003> recovery.img
<ID:0/003> persist.img.ext4
<ID:0/003> system.img.ext4
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
IF ANYONE CAN TELL ME WHAT IM DOING WRONG THAT WOULD BE GREAT... THANKS
Hi
Please explain your issue in the Q&A section of your device: http://forum.xda-developers.com/att-galaxy-s5/help
Do not hesitate to share more information about your situation (which files you have used, Odin version, checkboxes in Odin and so on). It will help others to help you
Thank you for using XDA Assist.
Good luck!
Hi guys, i have flashed Russia firmware[I9500XXUHOH7_I9500SERHOH7_SER - if it does even matter ] for i9500 ( i'm from romania ) and i can't find the right modem to flash as mobile data doesn't work and wi-fi wouldn't turn on at all. My baseband is XXUHOD4 and i couldn't find it on the i9500 modem threads or anywhere similar, like XXUH*** as i heard it's compatible aswell.
Please read everything before doing anything else. Ask for more information, i'd appreciate some fast help
UP : I have tried to flash some modems, XXUHOD7 and XXUHOE2 but odin fails everytime, here is the log.
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Can't open the serial(COM) port.
<OSM> All threads completed. (succeed 0 / failed 1)
<OSM> All threads completed. (succeed 0 / failed 0)
<ID:0/003> Removed!!
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> modem.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> Transmission Complete..
<ID:0/003> Now Writing.. Please wait about 2 minutes
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Receive Response from boot-loader
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
I did nothing else to phone but to root it and backup EFS. I have TWRP !
Hi and thank you for using XDA Assist
I saw you already posted into a right section so i'm gonna close this thread now.
Good luck!
Hello,
i have an issue with my Galaxy S6 (SM-G920F UK VOD) i believe it to be bricked, and not soft bricked. i can't get the phone to boot no matter what i try.
It all started after i had rooted the device, the root was successful and worked a treat until i decided i would like to play about with twrp. now i can't locate E/ and there does not seem to be any contents inside of the system folder.
Any help would be greatly appreciated and sorry if i have left out any important info.
I don't know if this is important but i have a recovery log.
pastebin com /PKE5fzgJ
trying to flash stock firmware using odin v3.10
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1005)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1005)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
odin 3.10 says this when i try to install firmware on my bricked s6 edge.
<ID:0/004> Added!!
<ID:0/004> Odin engine v(ID:3.1005)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sboot.bin
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Can someone please help me.
Mate ur failed is at bootloader means u Trying to flash old bootloader on newer one then knox wont let u install it success so download the latest fw from sammobile firmweare then flash it again ok
Good luck,,