Can't Flash Stock ROM - G920F - Galaxy S6 Q&A, Help & Troubleshooting

Been trying to flash Gaakxy s6 back to stock for hours. I get this message in ODIN
<ID:0/013> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G920FXXU2POFC_G920FVFG2BOF2_G920FXXU2POFC_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/013> Odin engine v(ID:3.1005)..
<ID:0/013> File analysis..
<ID:0/013> SetupConnection..
<ID:0/013> Initialzation..
<ID:0/013> Get PIT for mapping..
<ID:0/013> Firmware update start..
<ID:0/013> SingleDownload.
<ID:0/013> sboot.bin
<ID:0/013> NAND Write Start!!
<ID:0/013> cm.bin
<ID:0/013> boot.img
<ID:0/013> recovery.img
<ID:0/013> system.img
<ID:0/013> modem.bin
<ID:0/013> cache.img
<ID:0/013> hidden.img
<ID:0/013> FAIL!
<ID:0/013>
<ID:0/013> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Do i need to flash pit to the phone?
Any help is much appreciated

Try redownloading the ROM from yor source website and flash.

roydok said:
Try redownloading the ROM from yor source website and flash.
Click to expand...
Click to collapse
I found a solution, but I cant seem to get one part of it to work -.-
Read to extract the recovery.img and to change the file to recovery.img.tar. However the file type wont change

after extracting the hidden.img and changing it to hidden.img.tar (finally got it to work)
It says the odin communicator has stopped working..
Anyone have any suggestions?

Related

Sprint - Issues when downgrading to 4.4.4

Has anyone tried to downgrade a note edge from Android 5.0.1 to Android 4.4.4?
It is currently on N915PVPU2BOC8. I tried flashing N915PVPU1ANK1 downloaded from sammobile. But it fails in ODIN
Below is the log file. Any help will be highly appreciated.
<ID:0/008> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N915PVPU1ANK1_N915PSPT1ANK1_N915PVPU1ANK1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/008> Odin v.3 engine (ID:8)..
<ID:0/008> File analysis..
<ID:0/008> SetupConnection..
<ID:0/008> Initialzation..
<ID:0/008> Get PIT for mapping..
<ID:0/008> Firmware update start..
<ID:0/008> SingleDownload.
<ID:0/008> aboot.mbn
<ID:0/008> NAND Write Start!!
<ID:0/008> sbl1.mbn
<ID:0/008> rpm.mbn
<ID:0/008> FAIL! (Auth)
<ID:0/008>
<ID:0/008> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
You cant just odin back to kitkat. The bootloader is the issue. Once you update the bootloader to lollipop, you're stuck. Unless, chainfire would update his mobile odin to be compatible to our devices. Then we would have a shot.

Help Me with my phone

Hello
i had installed G920i INDIA 5.1.1 but today i downloaded G920i Trinidad and Tobago 5.1.1 (best firmware) and when i was installing it ODIN says FAIL and i forced device to reboot and it shows to me: error updating firmware, connect device to SmartSwitch.
- i was no downgrading my device in ODIN i dont know why it sayed to me FAIL.. WTF?
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G920IDVU2COF8_G920IUUB2COF9_G920IDVU2COF8_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/008> Added!!
<ID:0/008> Odin engine v(ID:3.1005)..
<ID:0/008> File analysis..
<ID:0/008> SetupConnection..
<ID:0/008> Initialzation..
<ID:0/008> Get PIT for mapping..
<ID:0/008> Firmware update start..
<ID:0/008> SingleDownload.
<ID:0/008> sboot.bin
<ID:0/008> NAND Write Start!!
<ID:0/008> cm.bin
<ID:0/008> boot.img
<ID:0/008> recovery.img
<ID:0/008> system.img
<ID:0/008> cache.img
<ID:0/008> hidden.img
<ID:0/008> FAIL!
<ID:0/008>
<ID:0/008> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
WHAT SHOULD I DO?

[Completed] Error while using ODIN to flash to stock rom on note 4

ive tried using Odin v3.09 and v1.85 did't have any luck with either one. Ive used Sammobile to get the stock rom for my verizon note 4. it starts but then fails. the message i get from Odin reads:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N910VVRU1BOAF_N910VVZW1BOAF_N910VVRU1BOAF_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl1.mbn
<ID:0/003> rpm.mbn
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
jmor97 said:
ive tried using Odin v3.09 and v1.85 did't have any luck with either one. Ive used Sammobile to get the stock rom for my verizon note 4. it starts but then fails. the message i get from Odin reads:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N910VVRU1BOAF_N910VVZW1BOAF_N910VVRU1BOAF_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl1.mbn
<ID:0/003> rpm.mbn
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Greetings and welcome to assist. Are you trying to flash an older firmware than your current bootloader ? You can download the latest firmwares here on updato
https://forum.xda-developers.com/galaxy-s7/how-to/updato-largest-online-firmware-archive-t3413785
or you can use kies/smartswitch to flash latest firmware/emergency firmware recovery
Good Luck
Sawdoctor

How to upadate Nougat to the latest version???

Hello,
i have the DPLT nougat firmware and I want to update to the latest one. The only option is using Odin? Can I do it thru zip file?
I have twrp. Will I nee to put it again, and root, and clean the data partition and everything...?
Thanks
dari-woka said:
Hello,
i have the DPLT nougat firmware and I want to update to the latest one. The only option is using Odin? Can I do it thru zip file?
I have twrp. Will I nee to put it again, and root, and clean the data partition and everything...?
Thanks
Click to expand...
Click to collapse
Check for OTA update first from settings menu If that does not work, flash "HOME_CSC" from the new firmware via Odin and your data should not be affected.
mrd0pe said:
Check for OTA update first from settings menu If that does not work, flash "HOME_CSC" from the new firmware via Odin and your data should not be affected.
Click to expand...
Click to collapse
thanks for the answer, but it does not update the system when I check it on the phone
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/008> Added!!
<ID:0/008> Odin engine v(ID:3.1203)..
<ID:0/008> File analysis..
<ID:0/008> SetupConnection..
<ID:0/008> Initialzation..
<ID:0/008> Set PIT file..
<ID:0/008> DO NOT TURN OFF TARGET!!
<ID:0/008> Get PIT for mapping..
<ID:0/008> Firmware update start..
<ID:0/008> SingleDownload.
<ID:0/008> cache.img
<ID:0/008> hidden.img
<ID:0/008> RQT_CLOSE !!
<ID:0/008> RES OK !!
<ID:0/008> Removed!!
<ID:0/008> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
dari-woka said:
thanks for the answer, but it does not update the system when I check it on the phone
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/008> Added!!
<ID:0/008> Odin engine v(ID:3.1203)..
<ID:0/008> File analysis..
<ID:0/008> SetupConnection..
<ID:0/008> Initialzation..
<ID:0/008> Set PIT file..
<ID:0/008> DO NOT TURN OFF TARGET!!
<ID:0/008> Get PIT for mapping..
<ID:0/008> Firmware update start..
<ID:0/008> SingleDownload.
<ID:0/008> cache.img
<ID:0/008> hidden.img
<ID:0/008> RQT_CLOSE !!
<ID:0/008> RES OK !!
<ID:0/008> Removed!!
<ID:0/008> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
Click to expand...
Click to collapse
My bad, I guess i wrote that reply a little too fast.. It's the AP file you should flash.

GT-i9105p can't flash stock rom

Hello, i am having a problem flashing the stock rom on GT-i9105P, i tried alot of roms but still none of them works.
I tried 4 Files repair firmware 4.1.2 and this is the log:
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> BcmBoot.img
<ID:0/005> NAND Write Start!!
<ID:0/005> HEDGE_RF_LE_SS_CAPRI_00.bin
<ID:0/005> sysparm_dep.img
<ID:0/005> sysparm2_dep_blob.img
<ID:0/005> sboot.bin
<ID:0/005> param.lfs
<ID:0/005> dt-blob
<ID:0/005> vc-firmware.img
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> system.img
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
---------------------------------------------------------------
4.1.2 Stock rom 1 file, flash log:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9105PXXAMC2_I9105POXXAMB5_I9105PXXAMC1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> vc-firmware.img
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> BcmCP.img
<ID:0/005> dt-blob
<ID:0/005> cache.img
<ID:0/005> system.img
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
-------------------------------------------------------
4.2.2 Stock rom 1 file, flash log:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9105PXXUBNB1_I9105POXABNA1_I9105PXXUBNB1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I also trie alot of Odin versions, but none works :/
Help me please, i've been trying to flash it from 2 days ago
Have you tried flashing RedRom, made by me?
It's stock 4.2.2 + extra optimizations.
Johnny TDN said:
Have you tried flashing RedRom, made by me?
It's stock 4.2.2 + extra optimizations.
Click to expand...
Click to collapse
First, thanks for replying.
No, i didn't try it..i would like to ask if you can give me it!
Goat678 said:
First, thanks for replying.
No, i didn't try it..i would like to ask if you can give me it!
Click to expand...
Click to collapse
Check my threads on my.profile. You will find RedRom there.
Johnny TDN said:
Check my threads on my.profile. You will find RedRom there.
Click to expand...
Click to collapse
Well, thx i already found it..
But still having a problem in odin while flashing TWRP/CWM recoveries...
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> TWRP-2.6.30_4.2.2_ODIN-s2vep.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> recovery.img
<ID:0/003> NAND Write Start!!
<ID:0/003> Complete(Write) operation failed.
<ID:0/003> Added!!
Can you help me please?
Goat678 said:
Well, thx i already found it..
But still having a problem in odin while flashing TWRP/CWM recoveries...
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> TWRP-2.6.30_4.2.2_ODIN-s2vep.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> recovery.img
<ID:0/003> NAND Write Start!!
<ID:0/003> Complete(Write) operation failed.
<ID:0/003> Added!!
Can you help me please?
Click to expand...
Click to collapse
If you have root on your phone, use Flashify.
...
Johnny TDN said:
If you have root on your phone, use Flashify.
Click to expand...
Click to collapse
Well, the phone is not turning on.
While turning on shows this message "Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again."
and i cannot boot to recovery mode on my device and cannot flash any thing :/
Goat678 said:
Well, the phone is not turning on.
While turning on shows this message "Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again."
and i cannot boot to recovery mode on my device and cannot flash any thing :/
Click to expand...
Click to collapse
Try this one
https://m.youtube.com/watch?v=7zEhC4kvMUE
Goat678 said:
Well, the phone is not turning on.
While turning on shows this message "Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again."
and i cannot boot to recovery mode on my device and cannot flash any thing :/
Click to expand...
Click to collapse
You fixed your problem?
Johnny TDN said:
You fixed your problem?
Click to expand...
Click to collapse
Unfortunately, no.
I still can't fix it
Goat678 said:
Unfortunately, no.
I still can't fix it
Click to expand...
Click to collapse
Then i'm afraid that you must buy a new motherboard. Sorry.
Johnny TDN said:
Then i'm afraid that you must buy a new motherboard. Sorry.
Click to expand...
Click to collapse
Well, i kept trying till i just flashed TWRP recovery, then installed your RedRom
and its very good!
Thanks ♥

Categories

Resources