Hello everyone , I bought this tablet China a few months ago . After a short time began to not work and the screen is not lit more . After it resumed but not the speaker that don't work. Then I opened the back cover and tried to release the speaker from his position and I noticed that very warming . I would like to change it but I can not find the spare parts . You know where to find them ? They go well with other parts ?
Related
Last night I was going to bed and tried to set up an alarm for the morning after. I then noticed that my PDA doesn't respond to touches. Everything else works just fine. There are some ripples on the screen and they can be noticed if you view it at a low angle. Here's how it looks:
As a new user I'm not allowed to post a link so here is the image address-> img694.imageshack.us/i/csc0717.jpg
The devise hasn't been abuse in any way. It hasn't been exposed to high nor too low temperatures(outside yesterday evening was around -2 ~ -3 degrees Celsius). Although I think that the short call I made(less than 10 seconds) couldn't have been enough to let the cold damage it. After and before that it has been in my trousers pocket.
Can anyone tell me what could have done this?
P.S. Digitizer - my mistake
Can't tell you what is the problem with your device but if it's digitizer you can get a cheap one here http://www.dealextreme.com/details.dx/sku.32150
it's just you have to wait a few weeks for it to come (at least I had to with some other things I bought on DX)
and I didn't buy this digitiser so I can't tell you more about it.
Hi!
have you put the screen protector on it anytime recently? If so, remove it and try again. I had this also once - bought and screen protector from the local HTC dealer, put it on (done it always so it wasn't the first time) and after a while I had the same problem as you. I did everyhting, hard resets, put a new ROM on..nothing. I also noticed the "oily spots" so I was frustrated. Finally I removed the protector and all of the sudden everything worked again.
I then bought a new protector and put it on very gently, I almost didn't push the portector on the screen and it works again. Still don't know if it was just a bad protector or what ws wrong. Try it..much simpler and easier than to go for a new digitizer.
[email protected]
The last time I've put a new one was November and to be honest I didn't expect it to last this long... after all a six-pack cost about $4
Can't try it now though cause the device is still in warranty and I returned in the shop for repair. I'm going to phone the guys there and inform them and I hope it works, cause they said that the problem is from the OS and reinstalling it will fix the problem. Don't think that it'll help but after giving it to them it's their problem to fix it I just want it working and if possible - faster
P.S. Did your digitizer stopped working at all or you'd have to push really hard to respond?
I have the same problem, I heated the screen with a air blower and the screen started responding. I don t think it is a permanent repair but at least it saves the day. This is my first day of repair so I don't know how long it will last.
End of april I tried extreme heat and cold on the screen and all of a sudden it started responding again. I still have that oily look on the lcd but it is working properly for almost 2 months now. (Just a quick update) (In the meantime I ordered spare LCD to replace it next time it stops responding)
Greetings!
Today my phone dropped of the desk and closed...i powered it on again vibration was working but screen was black!I tried my old lcd same thing...
For what part should i search t find or it's pointless...??
probably a hardware problem,the clue that the software works that it vibtrates,ry and buy a new scren or go to a shop to fix it
I've change screen i tried my old one(touch(digitizer) problem)..so i think this ( cgi.ebay.co.uk/Keypad-PCB-Flex-Cable-HTC-TOUCH-PRO-T7272-/320597490986?pt=UK_Mobiles_Accessories_RL&hash=item4aa5197d2a ) will solve the problem...
PS: Cant post link cause of forum restrictions.
Hello Dimgr
I lost my Touch Pro last month ( MB gave up) other part are perfectly working. As HTC service center said MB is gone i got courage to look inside deeply.
Therefore i can can the link is NaviCap assembly which is noway handles screen.
What i can guess i could be BD Slide
I though it would be that cause the screen connects with navikey.My phone hit the floor with the screen and keyboard was on!(i cant explain it sorry for my bad english :/) Any other suggestions??I dont want to rip my phone .
Just one day my TP stopped responding to touch, everything else working.
After few days screen went black, but phone was starting Navi key were glowing while charging, even phone was getting detected by PC.
I gave my TP to HTC service center they said Mother Board has gone & it was costing almost a new phone.
So i decided to sale the parts.
I sold Navi key to one of member on this forum only & its working perfectly, this confirms my doubt that Navi key is not the bug in your case as well.
Three things could have happened.
1. The best scenario is the jolt from the drop just dislodged the ribbon cable connecting to the screen. Resolution: Reseat ribbon cable on screen and on body of the phone (requires to open the phone)
2. The screen simple is busted and needs to be replaced.
3. The motherboard got busted and needs to be replaced.
1. The phone is open i even tried another screen all ribbon cables are checked :/
2. The screen seems to be ok... I dont think that both screes are faulty!!!
3.R.I.P. Htc touch pro...
My situation was same & HTC service center concluded that motherboard is gone.
So i believe your motherboard is also gone & this means there something which stops working after physical.
Because after my phone stopped responding to Touch i gave some shock with a hope that it may help in case of loose connection, but next day screen gone black.
I Everyone,
I notice this issue after i had replaced my touchscreen from a local dealer he has installed Chinese touchscreen is of ok quality as it provide 3 touch points after that day my phone proximity sensor started showing problems like sometime while receiving call my proximity sensor didnt work and some time screen use to go blank and didnt wake till the other guy didnt cut the line or have to continually press the power or home button to wake it up ... and then disconnect the call..
1.) I did sensor test for my phone and found that only after pressing at the place were sensor is situated it worked but only till your pressing it ther later it wont ...
2.) I did try to this http://forum.xda-developers.com/showthread.php?t=1313232 but it didnt work
3.) I tried to half Dissemble ( that mean i had opened the black panel were camera sensor is situated i didn't went further as i am not well known with such soc ) and reassemble my phone but it didnt work as there was no improvement .
Can someone help me how to fix this issue / and also if required i have tools to dissemble it and needed guide to do it.
Reserved
tanmoyc said:
I Everyone,
I notice this issue after i had replaced my touchscreen from a local dealer he has installed Chinese touchscreen is of ok quality as it provide 3 touch points after that day my phone proximity sensor started showing problems like sometime while receiving call my proximity sensor didnt work and some time screen use to go blank and didnt wake till the other guy didnt cut the line or have to continually press the power or home button to wake it up ... and then disconnect the call..
1.) I did sensor test for my phone and found that only after pressing at the place were sensor is situated it worked but only till your pressing it ther later it wont ...
2.) I did try to this http://forum.xda-developers.com/showthread.php?t=1313232 but it didnt work
3.) I tried to half Dissemble ( that mean i had opened the black panel were camera sensor is situated i didn't went further as i am not well known with such soc ) and reassemble my phone but it didnt work as there was no improvement .
Can someone help me how to fix this issue / and also if required i have tools to dissemble it and needed guide to do it.
Click to expand...
Click to collapse
Did you found a solution for that? I have the same problem with my Landvo L800!
Thanks!
eteles said:
Did you found a solution for that? I have the same problem with my Landvo L800!
Thanks!
Click to expand...
Click to collapse
No i didn't because replacing the touch screen wud cost me around 3500+ rupee from Samsung were as in local market you would get new phones for 4500+ rupee with much better hardware and latest OS which was ginger bread and ICS during those days so i didn't go for repairing it and when i tried inquire to second phone retailing shop cost of this phone if i buy second hand it was sold for 1500 rupee so.... it was not worth investment .
Hi guys,
I'm looking for some help and advice ! Long story short (will try), I purchased a used z5 with a display/screen issue (I guess).
The first owner told me he dropped the phone and that screen was cracked and not working anymore, so he brought it to the repair store... they replaced the screen with a new one, but they told him that the new screen was broken / dead on arrival, and that they would order a new one to replace it again. The guy couldn't wait another month to get is phone back working again, so he quit with the phone like that and purchased a used samsung.
I purchased the standard sony z5 from him. The screen have color lines in it... sometimes purple lines on the left of the screen, all from top to bottom, sometimes it's different (like right now it's alonost all white), but it is not working at all - I don't see anything useful on the screen.
The phone seems to be working though because the flash/photo work with the lower button on the left side... there is an alarm after midnight on it (I wake up like an idiot the first time it came up, trying to stop the alarm, but fingerprint is not mine and screen is not working... I was at the hotel, and damn it was loud... I think it waked up everyone in the other rooms around me before stopping it with power/fingerprint + volume up ;p)
So, I'm wondering if there's only the screen to replace again (with a good one), or if it's worst...
Does anyone know about that kind of issue, and which kind of screen would you put on it ? I want to put a good quality one to use the phone after that.
Thanks in advance for any help and advices !
Hello Everyone
I am having a Mi pad 1st generation 16gb version , which i bought way back in 2015 via flipkart. But for the last one and a half year the device has been laying idle in my table because of a display problem. The display is having a black shadow/line all through it. This problem started to creep two years back, at first it was not permanent (used to come and sometimes seem alright, turns to be normal) but later on it turned out to be worse.
**There has been no water damage
**have fell down few times without a case and tempered glass but was working perfectly alright even after that.
Went to a local repair shop, but they told to replace the whole display module with a new one.
Contacted mi service in my area to check, but they no idea of this product.
Did hard reset multiple times but nothing changed
Is this a problem which can be fixed without a lcd swap , like a fixing loose lcd ribbon connection .
Or should i need to go for an lcd change ?
** tried posting image urls ,but unable to do so because I am a new member and this is my first post.
Thanks & Regards