When replacing my S4's lcd I also decided to replace the frame/chassis. I used double sidded 3mm tape around the edges so the glass would stick to the frame/chassis, though some of the tape has lost it's stickyness. The glass has somewhat lifted up (I can get my nail underneath and lift the glass, i'm unsure if the lcd lifts up too), the areas of which have lost their stick is around the top corners (mainly around where the LED is but i've noticed it along the whole top of the phone). I've tried lifting the glass slightly and putting some more tape underneath it which has not work, also, i've tried heating it up with a heat gun which also did not. I am contemplating using hot glue but a the time being I am still undecided if it will be effective.
Has anyone else face a problem similar to mine? If so how do you correct it? Does anyone have a solution or any tips? (please note that this device is not under warranty of any sort)
Hi, thank you for using XDA assist. The best place to ask is in your device specific forum. I'm not sure what version of the S4 you have so try one of these, http://forum.xda-developers.com/galaxy-s4-att or, http://forum.xda-developers.com/galaxy-s4
Thread closed.
Related
So I just took out my sensation from the box and noticed the stock screen protector was off set and already peeling back a great amount on the top corner. I looked closely and noticed that the small tab at the top of the screen protector is actually inside the ridge of the phone, in that small thin crack where the front-screen ends. That was what cause the screen protector to not lay flat and started bending inward. I slowly peeled the protector back and when it came to the part that was "stuck" or jammed into the crack it took a good tug (I guess it was the adhesive...or it was really in there) for it to pop out. This couldn't have done any damage right? The small crack leads to nothing does it?
Probably just means it got caught in the gap when being fitted. I assume when you say 'crack' you mean the gap where the screen meets the rest of the body of the phone?
Yeah, where the black part ends.
Also, I have removed it and replaced it on more accurately since then and noticed it sticks to the screen very well, even attaching itself to parts that I have not even smoothed my fingers over yet, must be the static? Are there any disadvantages in using this as opposed to buying a new screen protector?
If it works then continue using it. We don't get them pre-fitted in the UK so I bought a 3rd party one
edit: delete this thread please mod thank you
Hey, I've done extensive searching on Google and these forums, something that is always left out is ABOUT GLUE.
I had a broken Nexus S screen and I changed my screen on the phone with a new one bought on eBay, the new screen works flawlessly but the OEM screen has a sort of adhesive tape that would make it adhere to the phone frame. And usually, all instructions for removing the screen talks about using some kind of a heat gun to make the glue loose.
Well the problem is that the new screens don't have this adhesive, I was wondering if anyone can suggest a kind of glue that would do the job for attaching the new screen to the phone. Right now as it is, the screen is only held in place to my phone by the wire which connects it to the phone's circuitboard.
on a german forum i've read a users experience... he used regular "super-glue" that you can buy everywhere. the one that makes your fingers stick in like 4-5 seconds.
he put little spots of glue everywhere the screen touches the plastic and quickly pushed the screen onto it. seems legit if you ask me - the screen doesnt weigh that much after all.
http://www.repairsuniverse.com/adhesive-strips-for-touch-screens.html
murfi said:
on a german forum i've read a users experience... he used regular "super-glue" that you can buy everywhere. the one that makes your fingers stick in like 4-5 seconds.
he put little spots of glue everywhere the screen touches the plastic and quickly pushed the screen onto it. seems legit if you ask me - the screen doesnt weigh that much after all.
Click to expand...
Click to collapse
That is ideally what I would really like to do instead of dealing with adhesive strips and then cutting the pieces to fit. I live in Germany now and the electronic store here said you can absolutely not use superglue and suggested instead that I used double-sided tape you buy from a photo store (Doppelseitiges, dünnes Klebeband).
What is the name of this 'super-glue' in Germany?
JoeyZazza said:
That is ideally what I would really like to do instead of dealing with adhesive strips and then cutting the pieces to fit. I live in Germany now and the electronic store here said you can absolutely not use superglue and suggested instead that I used double-sided tape you buy from a photo store (Doppelseitiges, dünnes Klebeband).
What is the name of this 'super-glue' in Germany?
Click to expand...
Click to collapse
Sekundenkleber
What if it broke again? I doubt you would be able to remove it if super glue it's used
Evo_Shift said:
What if it broke again? I doubt you would be able to remove it if super glue it's used
Click to expand...
Click to collapse
You're probably right but if it breaks again I'll just write off the phone as fully depreciated in my head.
Was the replacement one of these:
http://www.ebay.com/itm/All-New-Out...773?pt=LH_DefaultDomain_0&hash=item3a77cd07e5
or was it a full unit that go over $100?
So it's all about a Sensation with a defective digitizer. There are countless videos, DIYs, forums posts and blog articles on how to take the phone apart and to separate the digitizer form the screen. However, there is nothing on how to glue the new digitizer back in place. The options I've seen so far are:
1. Use 3M 2mm tape
2. Use what's left of the original glue (reheat and try to make it adhere to the new digitizer)
3. Use super glue
I live in Germany and it turns out that it's almost impossible to find 3M 2mm tape out here. So, could I just use any available type of double-sided tape and just cut it in 2mm stripes? What's the thickness of this 3M tape (need to know so that I can find a proper alternative).
However, the bigger question is, which of the three options mentioned above is the best? I guess that trying to make it work with the old adhesive leftovers is the worst thing to do, but is 3M (or equivalent) tape better than super glue? I mean, it's important that no dust comes through between the digitizer glass and the lcd screen... and that the newly fitted digitizer withstands the influence of high and low temperatures (hot sun in the summer, cold ice in the winter).
So, what would you say is best? I've never done this before, so I guess you have much more experience than I do...
Thanks
PS. Please excuse the typo in the thread title
icu___ said:
So it's all about a Sensation with a defective digitizer. There are countless videos, DIYs, forums posts and blog articles on how to take the phone apart and to separate the digitizer form the screen. However, there is nothing on how to glue the new digitizer back in place. The options I've seen so far are:
1. Use 3M 2mm tape
2. Use what's left of the original glue (reheat and try to make it adhere to the new digitizer)
3. Use super glue
I live in Germany and it turns out that it's almost impossible to find 3M 2mm tape out here. So, could I just use any available type of double-sided tape and just cut it in 2mm stripes? What's the thickness of this 3M tape (need to know so that I can find a proper alternative).
However, the bigger question is, which of the three options mentioned above is the best? I guess that trying to make it work with the old adhesive leftovers is the worst thing to do, but is 3M (or equivalent) tape better than super glue? I mean, it's important that no dust comes through between the digitizer glass and the lcd screen... and that the newly fitted digitizer withstands the influence of high and low temperatures (hot sun in the summer, cold ice in the winter).
So, what would you say is best? I've never done this before, so I guess you have much more experience than I do...
Thanks
Click to expand...
Click to collapse
Its not quite the same but I had this problem when replacing a LCD screen on a nintendo ds lite (bottom touch screen). I just went with the double sided sticky tape as I felt I could be far more accurate with it compared to super glue. I just cut it into the sizes I needed with a sharp knife and fitted it to the digitizer And then to the LCD. I have had no issues with it so far, its not slid or anything but then again it is housed in casing... if I was you I would try the tape first and if it seems unreliable try for the glue, just make sure you don't miss as it will muck up the digitizer if its no placed right I believe.
Good luck
Tapped out from my sexy nexus 7
I'd also say that the double sided sticky tape is probably the best thing to try out.. However, I'd like to know how thick the tape is. It should be thick enough to make the glas digitizer stick and also as thin as possible so that the new screen isn't appear to be higher than the old one...
My Tab 2 7 had a swirling crack on the digitizer (touchscreen). Looked for a tutorial on how to replace it in vain. Saw the teardown at Tech Republic, but that's it. No mention anywhere that I could find about how to do it. Decided to bite the bullet and ventured to fit a new one. Successful. Wrote down a quick guide thinking it might help someone since I saw a bunch of tabs with smashed digitizers on Ebay. Some claim it's gorilla glass, which makes me kind of wonder why they shatter so readily. I know, gorilla glass only scratch-resistant, but still...
Samsung sticks the digitizer to the bezel-frame with a tough double-sided tape, similar to the kind Asus uses on its tabs. A tutorial for the Tab 2 10 shows the use of a putty knife to scrape the digitizer off its frame, which wouldn't work with the 7, as its bezel-frame almost totally covers the edge of the glass back side. On the other hand, inserting anything metal in between from the front would scuff it badly.
The LCD display was taped to the magnesium frame, but is separate from the touchscreen, which need not be removed when replacing the digitizer.
What you need to do is to follow the steps in the teardown referred to above. As Tech Republic correctly pointed out, the internal layout is quite neat, unlike some of the tabs I've had the chance to disassemble. There are many thin cables, however, and you need to proceed with patience.
You must remove all components, so that only the frame with the digitizer and LCD is left. Eventually, you'd have to employ some source of heat, be it a heat gun, a hair dryer or a heat lamp to soften or to some extent melt the adhesive of the digitizer. Leaving any electronic component in place and the heat might destroy it. You can use brute force to separate the digitizer from the frame, but you'd more likely than not damage the LCD in the process.
What I did was use a heat gun at ~500 F, held at about 1 to 2 inches from the edge of the digitizer, and went back and forth over it, one side at a time, for no more than 30 to 35 seconds. I used a blunt object to push the glass out at spots plainly visible as illustrated in the attached thumbs below, then slid a plastic tool with a flared end to pry it from the bezel along its edge. Be careful how you handle the frame, since it would get burning hot at this point. As I moved from one side to another, I wedged a guitar pick between the glass and the frame to prevent them from sticking back together. You might pulverize parts of the glass as you go along, but in general it flexes quite a bit and wouldn't shatter.
Once you get it out, you need to remove the residual tape on the frame. The digitizer I bought was lined with new tape so I didn't have use any extra adhesive. It doesn't bind as strongly as the original tape, but enough to hold everything in place.
Putting it back is just the reverse. I took the extra step of reassembling the whole thing first with just the digitizer hanging loose, plugged it in, turned the tab on to make sure it functioned correctly before bonding it to the frame.
Basically, the process is nothing new. However, just the fact that someone has done it might give confidence to other DIYers in the future. Feel free to ask if any questions.
http://www.techrepublic.com/photos/cracking-open-the-samsung-galaxy-tab-2-70/6360139?
Thanks im going to give it a go. Any walkthrough tips by anyone else appreciated
Replacing the digitizer on this device is among the easiest ive seen. With no heat or taking anything off except the back I fixed one with only an isesamo
Hello, does anybody experiences in changing the Xperia E3 Digitizer Glass panel. Not the whole Display. Only the frontglass.
I didnt found any video or tutorial.
Maybe anybody knows a similar xperia device from where I can use its tutorial? Which xperia E devices have a similar the same kind of display assambley .
Any tip is welcome
thanks in advise
With phones that have the digitizer stuck onto the LCD, it isn't normally possible to replace one of the pieces without replacing the other. All those people selling just the glass on eBay and Amazon are just scams. However, if you have already bought a glass, just can try your luck by heating the screen with a hair dryer or a heat gun for a minute or two, then (with gloves, I learnt the hard way, REALLY hot) with a nylon string (the kind you use with fishing canes) slowly slide it back and forth in a corner between the LCD and and the glass, until you can remove the LCD easily. You may have to re-heat the screen several times. Now, there will be layer of glue on both the screen and the LCD. Try removing the glue. I can't tell you how, as I don't know how to. WARNING: Don't use alcohol or nail-polish remover to try to remove the glue, as it doesn't remove it well, and it damages the screen. Once that is done, you can try to somehow glue the LCD to the new screen. Once again, I can't tell you how as I don't know how to.
If you are successful, please write back saying how.