Related
I got my lovely droid 2 global (white) today, which is amazing. However, when I turned on the phone, it required me to activate. How can I activate it in Toronto, Canada without in US? Thanks.
Exit that wizard, switch to GSM/UMTS and you are ready to go (assuming you unlocked)
hi all,
i've been using my lovely Droid 2 Global outside US for quite a while (unlocked and using GSM network), and it worked all fine till today...
i tried to install fission today, and it didn't work for me (it just won't boot up), so i restore to 2.3.29, and finally managed to boot it up...
but after i power up, and enter PIN for my SIM, it requires me to Activate the phone...when i hit Activate, it immediately show "Phone Activation not supported on this network"...any suggestion on what i should do? i think i have the unlock code that i got from the buyer, but the phone doesn't even give me a chance to enter it!!!
i don't need to use Verizon network, i just want to use my D2G under GSM!! Please help!
i should have asked: why i need to re-activate again simply bcs i restore from a SBF??? I thought it shall stay as activated and unlocked once it was done...am i thinking wrongly?!
Don't freak up. Activation is only for CDMA radio. Every time you do factory restore (wipe data) CDMA programming gets erased too. GSM radio doesn't need activation. Simply ignore this, switch to GSM/UMTS mode and start using your phone.
If you have US account and you want to reactivate so you can use CDMA roaming feature, you need to do manual activation, but you may need Verizon's support to help you with some numbers you need to put up in programming.
BTW - the boot loop happened because you didn't wipe data after SBF. Fission (and any other non-stock ROM) will cause boot loop if you don't wipe data after SBF flash. (SBF flash process does not wipe data as part of the flashing).
GSM radio need to activate to use outside USA ! You need to contact with Verizon to get unlock code or use some unlock sim
tigerboy said:
GSM radio need to activate to use outside USA ! You need to contact with Verizon to get unlock code or use some unlock sim
Click to expand...
Click to collapse
You are mistaking unlocking with activation process. On GSM you activate the SIM card (Subscriber Identification Module), while on CDMA the "SIM" is integrated in the radio, hence you activate the radio.
For Droid 2 Global since it has essentially 2 radios - a GSM and a CDMA one, for GSM you need active SIM card to activate and for CDMA you need to make sure phone's MEID is active on your Verizon account then you program it (activte) either automatically while on Verizon network by dialling *228 or manually by calling Verizon support.
For the GSM radio in D2G, in order to use non-Verizon SIM in it, you need to unlock the phone first. Once unlocked, phone remains permanently unlocked and no SBF or wipe or anything will change this status.
Hey guys. I just bought an unlocked D2G on ebay so I thought I would share my experiences.
I got to the same screen where I was told "phone activation not supported on this network" and it was extremely frustrating. my only option was to hit ok and go back to the "touch the android" screen. I tried everything including the menu button. Nothing worked. This was with my SIM card inserted.
So I took out my SIM card and tried again. this time the menu button worked; it brought up the wireless options menu. I wanted to switch to "GSM only" as I had a feeling that would fix the problem. But I was told "no GSM card, must use CDMA mode". So, feeling stuck, I called Verizon, and after waiting on hold with the first CSR, and getting about 30 seconds into the phone call with the high up tech guy, I was in the middle of telling him about how in CDMA mode the wireless options menu would come up, but not with a SIM card inserted, the wireless options menu actually did come up. So I switched to "GSM only" and I was in!
Well, sorta. I had to get the phone linked with my google account via wifi, because the phone had no internet at all. A quick search of the internet revealed that this was a common problem - "I can talk on my D2G, but no data!" I called Rogers and sure enough, there were some settings I had to change to make this work.
Go into wireless options, then mobile network settings, then GSM/UMTS options (I assume you have a D2G because you want a droid you can put your SIM card in, right?) and then to Access Point Names. As this phone is unlocked, there are no APNs listed and your phone is neutered until one is added. I had no idea because my last phone was straight from Rogers and was of course hardwired to know this stuff.
Setting up the APN is really easy. just give it any name, list the APN as internet.com, MCC is 302, and MNC is 720. That's all. Back out. You will notice nothing is showing there. Don't do it again. It's there, but it's not showing up until you reboot. On my first reboot I had the 3G icon pop up in the notification bar and just about filled my pants. finally, the phone I paid $400 for was fully functional! No issues since then. Smooth as butter.
Thanks for the information and sharing leobg and seventieslord!
Gingerbread's rolling out, I'm planning to update my dad's D2G, but we're outside the US with an unlocked phone using GSM. I was worried after updating to Gingerbread, the phone would ask for a reactivation. This thread put my mind to rest
seventieslord said:
Hey guys. I just bought an unlocked D2G on ebay so I thought I would share my experiences.
I got to the same screen where I was told "phone activation not supported on this network" and it was extremely frustrating. my only option was to hit ok and go back to the "touch the android" screen. I tried everything including the menu button. Nothing worked. This was with my SIM card inserted.
So I took out my SIM card and tried again. this time the menu button worked; it brought up the wireless options menu. I wanted to switch to "GSM only" as I had a feeling that would fix the problem. But I was told "no GSM card, must use CDMA mode". So, feeling stuck, I called Verizon, and after waiting on hold with the first CSR, and getting about 30 seconds into the phone call with the high up tech guy, I was in the middle of telling him about how in CDMA mode the wireless options menu would come up, but not with a SIM card inserted, the wireless options menu actually did come up. So I switched to "GSM only" and I was in!
Well, sorta. I had to get the phone linked with my google account via wifi, because the phone had no internet at all. A quick search of the internet revealed that this was a common problem - "I can talk on my D2G, but no data!" I called Rogers and sure enough, there were some settings I had to change to make this work.
Go into wireless options, then mobile network settings, then GSM/UMTS options (I assume you have a D2G because you want a droid you can put your SIM card in, right?) and then to Access Point Names. As this phone is unlocked, there are no APNs listed and your phone is neutered until one is added. I had no idea because my last phone was straight from Rogers and was of course hardwired to know this stuff.
Setting up the APN is really easy. just give it any name, list the APN as internet.com, MCC is 302, and MNC is 720. That's all. Back out. You will notice nothing is showing there. Don't do it again. It's there, but it's not showing up until you reboot. On my first reboot I had the 3G icon pop up in the notification bar and just about filled my pants. finally, the phone I paid $400 for was fully functional! No issues since then. Smooth as butter.
Click to expand...
Click to collapse
God damned life saver ...... It is such a small change.... Add a APN.....
THANK YOU !
Just got my Nexus 5 today.
However, in Wireless&networks / Mobile networks / Network Mode, I can only set it as 2G or LTE but not 3G.
I am currently on b-mobile in Japan and my Nexus 4 works fine on the network.
Wondering is it some sort of bug of KitKat or is it somewhat related to the SIM card I am using...
seanyseansean said:
Probably the sim card. Mine gives me the option, but another n5 on a different network (o2/UK) doesn't.
Click to expand...
Click to collapse
hmm, in my case, I can see the 3G option, just that whenever I select the 3G option, the system would automatically reset it when I navigate to other page.
Is that also the case on your N5 with O2/UK sim card?
On the other hand, I will test my N5 on different sim card tomorrow.
I have the same issue. If I select 4g, the dot stays when I go back, but I only get a full bar 2g connection. If I select 3g and go back, no dot is there but I only get a 2g connection.
Sometimes this was solved in previous handsets by going into the service menu and selecting 3g/2g from there.
MarkMcLovin said:
I have the same issue. If I select 4g, the dot stays when I go back, but I only get a full bar 2g connection. If I select 3g and go back, no dot is there but I only get a 2g connection.
Sometimes this was solved in previous handsets by going into the service menu and selecting 3g/2g from there.
Click to expand...
Click to collapse
I also tried forcing the N5 to use 3G only (by going into the test menu with "*#*#4636#*#*" code) but it still does not work...
OK, so I tried the SIM cards from my colleges, and my N5 can connect to 3G without problem.
It's weird that my SIM card works perfectly well on N4 but NOT N5...
Did not experience such SIM card computability issue before...
httimchen said:
I also tried forcing the N5 to use 3G only (by going into the test menu with "*#*#4636#*#*" code) but it still does not work...
Click to expand...
Click to collapse
Works for me now. Went into that test menu and selected GSM/CDMA auto PRL and I now have 3g. Didn't have to reboot.
3G cannot set for Virgin UK Sim
MarkMcLovin said:
Works for me now. Went into that test menu and selected GSM/CDMA auto PRL and I now have 3g. Didn't have to reboot.
Click to expand...
Click to collapse
I am also having the same problem, purchased the Nexus 5 from carphonewarehouse, can set on 4G or 2G, but when i set to 3G and comeback, it resets. Is that a SIM card problem? I tried to go on testing mode and apply GSM/CDMA auto PRL, that also not working. Is that a KitKat bug?
Same problem on Orange/EE in the UK. I can see the 3G option but phone won't let me change to 3G. Option never sticks. Just stays on 2G. Any ideas? Is this a known bug?
Thanks 101
101_North said:
Same problem on Orange/EE in the UK. I can see the 3G option but phone won't let me change to 3G. Option never sticks. Just stays on 2G. Any ideas? Is this a known bug?
Thanks 101
Click to expand...
Click to collapse
i think it's not a bug.i think it's a hardware problem. i'm having it with vodafone italy.
Same here on T-Mobile Austria :/
Already changed SIM card, without success. Maybe provider related issues?
unexist said:
Same here on T-Mobile Austria :/
Already changed SIM card, without success. Maybe provider related issues?
Click to expand...
Click to collapse
I'm on straight talk TT&T with a new SIM card, but sometimes the network mode doesn't stick. No idea why...
replaced a new 3G SIM, no luck
Just replaced a new 3G SIM Card didn't work the 3G option for me - Chunghwa Telecom Taiwan.
But I can select 2G, and dial number to make a phone call, so the SIM slot seem works fine, maybe just configuration issue?!
And, also I find a very annoying defect of my Nexus 5 32G(White), when hard-reset or flash to Factory Image, my Nexus 5 32G white goes crazy!! it just keep stuck and loop at Google Logo (not even show the 4 circle animation), and won't boot at all!
And I finally find a way to make it boot, by keep trying repeat flash factory, erasing userdata, erasing cache etc. is every had this issue?
EE/T-Mobile (uk) and I can't select 3g either, well I can but it doesn't stick.
I have a similar problem, except I can only select 3G / 4G, and not 2G because the 2G option isn't even displayed!! So infuriating. It still works through the *#*#4636#*#* menu, if I select GSM only then it does indeed go to 2G.
Is it possible that the SIM is somehow telling the phone OS it can't do 2G only? This didn't happen with my old carrier (same phone, only just switched). I have a feeling it's caused by the same thing that makes my phone number show up as 'unknown' now, too.
I have the same issue, I tried two different SIM, on is a Straight Talk sim that is set up to use the ATT network and used a T-Mobile sim card, both were unable to keep 3G as a setting.
My Nexus 5 seems that reluctant to drop from 3g to 2g when 4g is selected i have given up and now just manually select 2g to make sure i have a signal (im out in the sticks a bit). Sat at the PC with 4g selected i get no signal whatsoever, with 2g selected i get an indicated full signal strength.
Why on earth the N5 is so reluctant to dip its toe in the 2g territory when no data is on is beyond me.
I bought an Unlocked Canadian S6 recently, and it just won't let me connect to the LTE network.
Model Numer : SM-G920W8
Android Version : 5.0.2
Baseband : G920W8VLU1AOCG
Connecting to the LTE is not even an option. When I go in the Network Options, I get the choice between :
-WDCMA/GSM (auto connect)
- WDCMA only
- GSM only
I know for a fact that I am in the coverage zone, so no need to ask that silly question
I've tried different SIM cards, played in the options a bit, and factory reset the phone about 5 times now, yet nothing seems to work.
Also, when I try to do the update, it just reboots and gives me an Android logo and a failed Icon
I've only seen one other post like this from a carrier's support website, but no solutions were found.
**Update : For a reason, after a recovery, it will connect to the LTE for a bit or until next boot, then go back to what it is now.
First question, who did you buy the phone from? Second, Is it second hand? By default, Wind mobile does not allow the LTE option to be displayed in system settings as they as a carrier don't have LTE. It is blocked by the CSC setting for the carrier. As for other carriers It should leave you the option to connect in settings where you say it is not. If it is a Wind phone, You would need to change the CSC to enable the LTE selection. There is a method to force LTE even without option in settings, but I think it is removed in the latest firmware. Try dialing *#2263# in the dialer. It may bring you to menu that will allow you to select LTE. This is not a permanent method though as it will need to be done every boot. The other way, (If you are in fact a Wind/Mobilicity phone) is to enter dialer and enter *#272*IMEI# with IMEI being your devices unique code. If at all possible, take a full nand and Titanium Backup before doing this and be sure to transfer everything off the phone to a PC. This method wipes everything and I mean everything off the phone buy is a surefire way to enable LTE.
Yes, it was second hand. I didn't ask who was his carrier simply because it was unlocked.
I'll try it tomorrow, thanks for the information
Here is the menu you will see when you type the *#272*imei# code into your dialer. The codes are the carrier names. Mine which is GLW is Wind, BMC is Bell, RWC is Rogers, etc.
Maybe there is no LTE in your area...
roydok said:
Maybe there is no LTE in your area...
Click to expand...
Click to collapse
It would still be visible in the Settings/Mobile Networks/Network Mode menu which it is not. His problem is more than that.
BCSC said:
First question, who did you buy the phone from? Second, Is it second hand? By default, Wind mobile does not allow the LTE option to be displayed in system settings as they as a carrier don't have LTE. It is blocked by the CSC setting for the carrier. As for other carriers It should leave you the option to connect in settings where you say it is not. If it is a Wind phone, You would need to change the CSC to enable the LTE selection. There is a method to force LTE even without option in settings, but I think it is removed in the latest firmware. Try dialing *#2263# in the dialer. It may bring you to menu that will allow you to select LTE. This is not a permanent method though as it will need to be done every boot. The other way, (If you are in fact a Wind/Mobilicity phone) is to enter dialer and enter *#272*IMEI# with IMEI being your devices unique code. If at all possible, take a full nand and Titanium Backup before doing this and be sure to transfer everything off the phone to a PC. This method wipes everything and I mean everything off the phone buy is a surefire way to enable LTE.
Click to expand...
Click to collapse
Sweet! It works :good: Thanks man
Now, would you have any ideas on why the update won't work? I didn't get much into it yet, but I will soon.
I'm not sure why it wouldn't update, but now that you have changed the CSC you can download the update and flash with Odin. Pick your carrier and go to town. The guy running the following thread runs his own firmware host. He's got amazing DL speeds. Usually takes me 6 or so minutes to do the 1.6gb file. http://forum.xda-developers.com/showthread.php?t=3086387
I'm having the same issue.
Scurbs said:
Sweet! It works :good: Thanks man
Now, would you have any ideas on why the update won't work? I didn't get much into it yet, but I will soon.
Click to expand...
Click to collapse
Connected with someone selling a G920W8 version. LTE is disabled and the codes aren't working. Can you reaffirm which unlock code worked for you? I'm on Fido, what LTE network are you using?
hi BCSC
Thanks for the details. I searched complete net and read all articles but nothing set me up with the proper thing. i read your solution i dialled *#2263# and all i got is service mode and in that i went to band selection , LTE and the all ....... Yes and its showing LTE in mobile data. THanks so much.
But now another issue, network is showing perfect but no outgoing and incoming calls.
in incoming its showing busy and on outgoing its not connecting to another phone.
And, Lte is not showing in mobile networks, There only 3 options still are showing.
Mine is same Wind S6 but i had to use in India.
Let Me know
Thanks once again
Cheeerzzzzz
Varun
Picking LTE from the service mode will note make it visible from the settings menu. Its more of a workarpund instead of a way of permanently enabling it. As for the issue of no out/in calls, my best guess is that it could be due to which LTE bands are being used or are available in India. Unfortunatly I have no way to test that option. I only was successful in getting the Wind LTE option on Canadian carriers.
Sent from my SM-G935W8 using XDA-Developers mobile app
I'm on PD1 6.0.1 with a G920R7 nTelos. I rooted using CF-Auto root, flashed TWRP for the g920p, and installed the zip file from this thread... http://forum.xda-developers.com/showthread.php?t=2394689
After that I installed Phone INFO ★Samsung★ and used it to access the hidden menus. Went to the 2263 menu and set all band preferences to all and selected the LTE/GSM mode only, then went to the 4636 menu and set the radio to GSM/LTE (prl) auto. I've tried GSM only and it switches back to GSM/LTE (prl) auto on its own.
I now have access to a mess of options in the network mode selection screen in settings, and setting it to GSM only and 3g only still does not allow me to catch signal. In network operators it shows AT&T, yet if you try to manually select the network it never goes through. *#0011# still shows it switching through LTE bands and not staying on one or registering on the network. In the device info screen (4636 menu) it shows the correct phone number and AT&T for current network, but under cellinfo still shows it switching between LTE bands and under GSM disconnects it shows ======DATA======.
At this point I'm not quite sure what to try next. Please let me know if anyone has any ideas to try. Thank you.
EDIT: I've also tried the G920P domestic unlock and G920R4 unlock with a box, but no luck with either as expected.
i can do remotely if u want
blazie151 said:
I'm on PD1 6.0.1 with a G920R7 nTelos. I rooted using CF-Auto root, flashed TWRP for the g920p, and installed the zip file from this thread... http://forum.xda-developers.com/showthread.php?t=2394689
After that I installed Phone INFO ★Samsung★ and used it to access the hidden menus. Went to the 2263 menu and set all band preferences to all and selected the LTE/GSM mode only, then went to the 4636 menu and set the radio to GSM/LTE (prl) auto. I've tried GSM only and it switches back to GSM/LTE (prl) auto on its own.
I now have access to a mess of options in the network mode selection screen in settings, and setting it to GSM only and 3g only still does not allow me to catch signal. In network operators it shows AT&T, yet if you try to manually select the network it never goes through. *#0011# still shows it switching through LTE bands and not staying on one or registering on the network. In the device info screen (4636 menu) it shows the correct phone number and AT&T for current network, but under cellinfo still shows it switching between LTE bands and under GSM disconnects it shows ======DATA======.
At this point I'm not quite sure what to try next. Please let me know if anyone has any ideas to try. Thank you.
EDIT: I've also tried the G920P domestic unlock and G920R4 unlock with a box, but no luck with either as expected.
Click to expand...
Click to collapse
Stifilz does remote unlocks also for free
asadnow2k said:
i can do remotely if u want
Click to expand...
Click to collapse
I have a box but the device isn't supported, it's not locked I must just be missing something. Anyway you could private message me what I'm missing? I've been through all the settings messing with it and all, even flashed the CDMA to GSM zip floating around here. I know I'm missing something silly. Any help would be appreciated and I don't mind sending you a donation provided I can do this myself next time.
TheMadScientist420 said:
Stifilz does remote unlocks also for free
Click to expand...
Click to collapse
I just messaged him on Hangouts. I don't know if its something he can help with or not because I believe we have the same box and the g900r7 isn't supported. This isn't even answered on that Voldemort website.
Did you figure this one out? I'm also interested in GSM unlocking this phone.
Messing around with it I was able to get an ATT Sim card to pull 3g data but no call/text or lte.
I'm customer of the local carrier "Drei" (Hutchison) but my Pixel (bought in Germany) does not connect to the 4G / LTE network.
The support of Drei is not able to help me. LTE is working fine with the same SIM on the OnePlus One.
Any clue how to fix that?
There is regional problem I came across. In India here we dont have VOLTE support on pixel
FallinHigh said:
I'm customer of the local carrier "Drei" (Hutchison) but my Pixel (bought in Germany) does not connect to the 4G / LTE network.
The support of Drei is not able to help me. LTE is working fine with the same SIM on the OnePlus One.
Any clue how to fix that?
Click to expand...
Click to collapse
What LTE bands do they use on Drei?
Same happen to me in Portugal with MEO. I can't seem to solve it. Talked with my carrier support, they don't know why I don't have 4G/LTE.
I never got 4G, but my SIMCard has no issues with iPhone getting 4G right away.
Is it Pixel issue? I start to think it is..
3/Drei is listed here: https://en.wikipedia.org/wiki/List_of_LTE_networks_in_Europe#Commercial_deployments
The specs of the Pixel are listed here: https://madeby.google.com/phone/specs/
That is all information I have got.
Is there any possibility to display information about nearby LTE senders via an app?
After activating "LTE only" via *#*#4636#*#* it works. Everytime I search for networks or reboot my phone it still connects via 3G and switches back to "LTE UMTS auto (PRL)".
Seems to be a software issue.
FallinHigh said:
After activating "LTE only" via *#*#4636#*#* it works. Everytime I search for networks or reboot my phone it still connects via 3G and switches back to "LTE UMTS auto (PRL)".
Seems to be a software issue.
Click to expand...
Click to collapse
I use the phone on Verizon and don't have any problems connecting to LTE using any available mode (Global, LTE/CDMA or LTE/GSM/UMTS). However, if I set the mode to LTE-only via the menu, it will also reset when I either reboot the phone or if I just open the "Cellular networks" menu. I think it's how it supposed to work because that menu doesn't have the LTE-only option, so it resets the mode to whatever you see there. The solution is simple - if you reboot the phone change the mode again and don't go to the "Cellular networks" menu
Regarding why it doesn't work with "LTE UMTS auto (PRL)", it might be because Drei didn't configure a handover from UMTS to LTE on the cell site you're connected to. It looks like Pixel finds UMTS signal first, but doesn't know that LTE signal exists due to a missing handover. Another phone might be fine if it searches for LTE signal first. But if you can see another phone switching from UMTS to LTE in the same spot, my theory is wrong.