[how to make a scatter file for any android][MTK devices]

[how to make a scatter file for any android][MTK devices] - General Topics

In this post I will teach you how to make your own scatter file
Requirements:
1. Mtk device
2. PC or laptop
3. MTKdroid tools
Procedure:
1. From your android device, enable USB debugging
For that go to ->Settings ->Developer options
2. Connect your android device to you
computer via USB cable. Drivers must be
Installed in your system.
3. From your computer, run MTKdroid
application as administrator (except for
Windows XP).
4. Wait for MTK Droid Tools to load your
android device's info. Just wait few
seconds.
5. If the tool is done loading your device,
click on Blocks Map
6. A new window will appear, click on Create scatter file
7. Now, navigate to where do you want to
save the scatter file of your device. Save
it to somewhere safe because it can be
used for future flashing.
8. Now you are Done..
Enjoy flashing..
Hit thanks button if this post helped you

hi
i have iris alfa rooted
i want to install stock rom which needs scatter file
now if i create a scatter file with the above steps, would it be the same as the stock scatter file

Related

Micromax a 45 - ALL THINGS ROOT !

I've decided to open this thread for development md mmx ninja a45 .
Rom dump :
http://www.mediafire.com/?gla8fgpwl0r0hvf
ROOTING (credits:rishu)
pre requisites *a45 drivers and *superoneclick
firstly dissable ur antivirus...
1)download drivers available at micromax's site
2)Connect your device on your PC and be sure that USB Debugging is enabled.
Your PC will ask on how will you install the driver, choose “Install from a specific location” then navigate to where you had downloaded earlier.
3)After drivers has been already installed, open super one click.
4)Click the “Root” button.
Then rooting will start automatically....
Installing CWM: (credits antonysabish)
Micromax A45 Clockworkmod
Recovery
Here's how to get Clockworkmod recovery
with SP Flash Tool:
1. Download SP Flash Tool.
2. Download MT6573_Android_scatter.txt.
3. Download a45recovery-cwm.zip and extract it.
4. Extract SPF Tool.zip and Run
Flash_tool.exe from there.
5. Click File->Open Scatter-loading file and
select the MT6573_Android_scatter.txt you
downloaded.
6. Now uncheck everything except
RECOVERY . Click on recovery and select
a45recovery-cwm.img you downloaded.
7. Now turn off your Micromax A45,
remove battery and put it back( DONT
switch it back on).
8. Press Download in the SP Flash Tool
window, then When the countdown starts,
connect your phone to PC.
9. After it's done, disconnect the phone,
remove battery and put it back. Boot the
phone into Recovery mode, You should
have Clockworkmod v5.8.1.9
download super one click : http://205.196.120.108/ll71hms5t67g/l291ej5damzoujk/SuperOneClickv2.3.3-ShortFuse.rar
Anyone interested please join

[GUIDE] [ROOT] Alcatel One Touch T' Pop

Hello again XDA, kirito9 here with another guide on how to root the Alcatel One Touch T'pop. I decided to make a guide because i have not seen any guide on XDA concerning this phone and rooting.
Disclaimer: Your warranty is now void. You do this in your own risk. I do not take any responsibility to your device.
BACKUP YOUR DEVICE BEFORE DOING ANYTHING IN THE EVENT SOMETHING GOES WRONG.
Requirements:
- Windows 7 PC ( tested only on this)
- ADB drivers
- MTK drivers
- MT6575 Scatter file
- CWM or TWRP recovery
- SP Flash Tools
- SuperSU
Lets Begin
Flashing CWM or TWRP
1. First thing to do is to make sure all required drivers are installed. Do that by downloading the Universal ADB driver from this link and install it.
2. Then install the MTK drivers so that SP flash tools can work. Get those here, extract and install the drivers for windows 7.
3. Download your preferred recovery either CWM or TWRP below and place somewhere on your computer where you can find it easily.
4. Download the SP flash tools here and extract them.
5. Download the MT6575 Scatter file attached below.
6. Download the SuperSU zip file and place it either on internal or external of the phone.
6. Go to the sp flash tools folder and run flashtool.exe as administrator.
7. Click on scatter loading and select the MT6575 scatter file you downloaded.
8. Click on the recovery checkbox and then click on the white space in location. Select the recovery of your choice.
9. Turn off the phone, remove the battery then reinsert it.
10. Click on download and then connect the phone.
11. Wait for the flashing to complete then remove your phone.
Rooting the phone.
1. Boot into recovery then go to install, select the SuperSu zip file and install it.
2. After the flashing is complete, reboot your phone and see the SuperSU app in the app drawer
Credits
- me
-Chainfire for his SuperSu

May you also upload any stock ROM for OT-4010D ???

[ROOT][RECOVERY][ROM] LAVA iris 300 style

Root : JB 4.2
Root LAVA iris 300
1. Download The Framaroot APK here and install it to your phone.
2. Goto Settings > Security > and tick “Unknown Sources“.
3. Run Framaroot, choose Superuser or SuperSU.
4. Select Boromir or Bahamir.
5. You will see Success.
6. Reboot device, Done. :good:
OR
1. Download The Kingoroot APK here and install it to your phone.
2. Run King Root application.
3. Click on Root button. It take sometime for the rooting process.
4. Reboot device, done. :good:
Stock Rom : JB 4.2
Unbrick your LAVA iris 300
1. Download Stock Rom from here (by xdafirmware)and extract it.
2. Download mtk_usb driver from here and install it.
3. Open Sp flash tool, select scatter.txt.
4. Click on download.
5. Power off your device (confirm off), then connect usb cable. (dnt press any key, flash with battery).
6. System will detect your device as mediatek_preloader_com.
7. Sp Tool will recognise your Phone and flashing will start.
8. Once the flashing process is completed, a green ring will appear on your system.
9. Dissconnect, Power On, Done :good:
Full Instructions with images here (by techsultan).
Nandroid Backup/restore (recommended)
Take Full backup of your LAVA iris 300
You can take full backup with Custom recovery (Carliv/TWRP).
OR
1. Download Mtkdroid tool here (by gsmhosting)and extract it.
2. Download Pdanet+ andoid usb driver from here and install it.
3. Install BusyBox.apk in your device from playstore.
4. Enable debugging mode on your phone > Settings > Development. Tap 'android usb debugging' and make sure it's checked.
(if there is no option for development then go to setting > about phone > build number, tap on it 7 times, Go back to Settings menu and now you'll be able to see “Developer options” there.)
5. Open MTK Droid Tools folder with right-click on 'MTKdroidTools.exe' and Select 'Run as administrator'.
6. Wait several seconds while MTK Droid Tools communicates with your device. give root permission to adb-shell on your device.
7. Click the 'root' button in MTK Droid Tools to get temporary root shell.
8. Now get nvram backup. For full backup go to 2nd tab click on backup.
9. Here will be saved all backup \MtkDroidTools\backups.
10. Prepare this backup to make it flashable through SP Flash Tool. To do it, click on To 'prepare blocks for Flash Tool.'
11. A new windows will appear asking for a .md5 file of the backup. So navigate to the MTK Droid Tools folder where your backup is found. Open the backup that your have created earlier and select the files.md5 click open.
12. Wait for MTK Droid Tools to copy the files for SP Flash Tool, check the status messages until the copying/task is complete. Done
Full Instructions with images here (by rajit).
Restore :
1. Open , SP Flash Tool.exe run as administrator. Load the scatter file (click scatter-loading) which you have prepared from MTK Droid Tools to be flashable through SP Flash Tool.
2. After you loaded scatter file, All must checked except for Cache and USERDATA and most importantly, do not check DSP_BL or Preloader else you'll brick it.
3. To restore device, click Download from SP Flash Tool, a prompt will appear, just click Yes. Immediately connect your Power OFF device to your computer via USB .
4. Wait for the tool to detect your device and restore the Stock ROM that you have made. An alert with a green circle appears after successfully downloading the restore.
Full Instructions with images here (by MTK Hacker Pro).
Custom Recovery : TWRP/CTR
( Download and flash it with Sp FLash tool. Press Vol up and Power Key to boot in Recovery. )
Twrp for LAVA iris 300
TWRP2.8.0 alpha here
Note : There is lots of bug in it. pls post here.
CTR for LAVA iris 300
Carliv 2.4 alpha here
Note : Flipped Screen Bug.

wahh! Now just make a best kitkat rom for 300 plz!! ur gr8

[Resolved] How to root Vodafone Smart Tab 7 (Tablet) VFD 1100 (Solved)

Hello,
After i searched almost 24 hours on the web for a way to root this stupid tablet, i find an unusual one.
I try to make it clear for all of you.
Requirements:
- PC running Windows 7/8/8.1/10 | You can use linux but I cannot guide you as how to setup adb drivers or preloader drivers,
- USB Cable,
- ADB-Setup file (see below),
- TWRP recovery aka recovery.img.zip,
- SP_Flash_Tool (SPFT),
- MT6580_Android_scatter.txt (see below),
- MTK_USB_All preloader usb vcom drivers,
- superuser.zip (don't confuse this file with phh superuser, they are not the same),
- phh superuser (install it at the end, on the tablet).
DO NOT EXTRACT the superuser.zip !!
You can extract all other files.
Flashing TWRP
1. Download the MTK_USB_All preloader drivers from the archive of this post and follow the guide on how to install.
2. Download the new SP_Flash_Tool from the archive of this post and extract it anywhere.
3. Open the SPFT folder and locate flash_tool.exe and RUN it as Administrator.
4. If it says anything like cannot locate scatter, press ok and ignore that message. Go to scatter loading and select your MT6580_Android_scatter file you downloaded.
5. Download TWRP recovery aka recovery.img.zip from the archive of this post.
Extract the archive to get the recovery.img file.
5.1 After you open the flash_tool.exe, look on the list from the scatter file for recovery; Follow step 6.
6. Select the recovery by pressing the little box next to it and then move over to location of the recovery and choose the recovery.img.
7. Power off your tablet, wait 1-2 minutes and then connect your usb cable to your PC.
8. Press Download at the top and then connect your tablet to your PC throught the USB Cable.
If you have the battery in and it doesn't work, wait until the logo of the tablet shows up then try again. If that doesn't work then try again without the battery.
8.1 When the Download is finished (you will see a red bar, then a green bar to confirm), if the tablet doesn't open up, remove the USB Cable from it and wait for few seconds.
Then the TWRP menu should appear. This should do the magic.
Rooting:
1. Download superuser.zip from the attached files and place it on your SD card.
1.1 ADB arhive has in it a ADB Drivers installer that only needs 15 seconds to do the trick. Please follow the instructions from there.
1.2 ADB folder will be located from default on partition C, or if you have another one, on the OS partition.
2. Reboot your phone to recovery using the command "adb reboot recovery" from a CMD runned as administrator from the ADB folder, or do it via external buttons.
2.1 When you execute the command "adb reboot recovery" the TWRP Menu will appear.
3. Navigate using volume buttons and select using power button, or touch if you want. Go to install from the TWRP Menu then choose superuser.zip from SD card.
Flashing should take only few secconds, then reboot your tablet.
4. Install phh superuser app from the arhive of this post and that's it. You will be rooted.:good:
* I hope this will help you to do this step more easily then me. Be well !
Password for archive is: vfd1100

DevOpsXDA said:
Hello,
After i searched almost 24 hours on the web for a way to root this stupid tablet, i find an unusual one.
I try to make it clear for all of you.
Requirements:
- PC running Windows 7/8/8.1/10 | You can use linux but I cannot guide you as how to setup adb drivers or preloader drivers,
- USB Cable,
- ADB-Setup file (see below),
- TWRP recovery aka recovery.img.zip,
- SP_Flash_Tool (SPFT),
- MT6580_Android_scatter.txt (see below),
- MTK_USB_All preloader usb vcom drivers,
- superuser.zip (don't confuse this file with phh superuser, they are not the same),
- phh superuser (install it at the end, on the tablet).
DO NOT EXTRACT the superuser.zip !!
You can extract all other files.
Flashing TWRP
1. Download the MTK_USB_All preloader drivers from the archive of this post and follow the guide on how to install.
2. Download the new SP_Flash_Tool from the archive of this post and extract it anywhere.
3. Open the SPFT folder and locate flash_tool.exe and RUN it as Administrator.
4. If it says anything like cannot locate scatter, press ok and ignore that message. Go to scatter loading and select your MT6580_Android_scatter file you downloaded.
5. Download TWRP recovery aka recovery.img.zip from the archive of this post.
Extract the archive to get the recovery.img file.
5.1 After you open the flash_tool.exe, look on the list from the scatter file for recovery; Follow step 6.
6. Select the recovery by pressing the little box next to it and then move over to location of the recovery and choose the recovery.img.
7. Power off your tablet, wait 1-2 minutes and then connect your usb cable to your PC.
8. Press Download at the top and then connect your tablet to your PC throught the USB Cable.
If you have the battery in and it doesn't work, wait until the logo of the tablet shows up then try again. If that doesn't work then try again without the battery.
8.1 When the Download is finished (you will see a red bar, then a green bar to confirm), if the tablet doesn't open up, remove the USB Cable from it and wait for few seconds.
Then the TWRP menu should appear. This should do the magic.
Rooting:
1. Download superuser.zip from the attached files and place it on your SD card.
1.1 ADB arhive has in it a ADB Drivers installer that only needs 15 seconds to do the trick. Please follow the instructions from there.
1.2 ADB folder will be located from default on partition C, or if you have another one, on the OS partition.
2. Reboot your phone to recovery using the command "adb reboot recovery" from a CMD runned as administrator from the ADB folder, or do it via external buttons.
2.1 When you execute the command "adb reboot recovery" the TWRP Menu will appear.
3. Navigate using volume buttons and select using power button, or touch if you want. Go to install from the TWRP Menu then choose superuser.zip from SD card.
Flashing should take only few secconds, then reboot your tablet.
4. Install phh superuser app from the arhive of this post and that's it. You will be rooted.:good:
* I hope this will help you to do this step more easily then me. Be well !
Password for archive is: vfd1100
Click to expand...
Click to collapse
Hi, i can use this way Also for Vodafone Smart Tab 10?

Question [Guide] How to use SP Flash tool [Windows Only!]

Today I'm going to write how to use so flash tool for OnePlus Nord CE 2
Before you begin download: https://drive.google.com/file/d/1fL8qqu_pBK1YU5xbgugLax7ZKU-k3ex7/view?usp=drivesdk
This includes sp flash tool for our MTK version, drivers and MTK Bypass files!
Requirements: PC or Laptop
Internet connection
USB cable
Take a backup of your data, Just in case if any error happens.
Windows Method
Requirements:
SP_Flash_Tool_5.2112.00.zip
drive.google.com
Decrypted OFP for our device! You can find it on Google!
Install Python from Windows Store
https://sourceforge.net/projects/li...ibusb-win32-devel-filter-1.2.6.0.exe/download
libusb-win32 - Having Issues? Click Here
Steps:
1) Extract the zip
2) Use the bundled QcomMtk_Driver_Setup_3.1.9.exe from the zip. for MTK Preloader USB VCOM driver it should be installed within windows 8 and above?
3)Download this file and install it, after installing power off phone and connect to pc while holding Vol+- (don't leave the buttons after connecting) . You might need this driver as well if it's not detected.
Press next, connect your device to PC while holding Vol+- buttons (your device needs to be powered off, and don't leave the buttons) and you will see the mtkdriver down below. Install it.
Choose MediaTek USB Port and install it.
4)Then run the brom.bat under Bypass folder (spflashtool/mtk-bypass/bypass). (for Linux, When available) use command: python3 mtk payload to start the BROM exploit!
5) Now power off the phone and connect the phone while holding volume + and - (Don't leave the buttons until the bypass is done)
6)After the above step Go into Flash Tool folder and open the SPFlash tool and launch flash_tool.exe
7) Click on Options>Options and go to Connections and select UART and set Baud Rate to 921600
8)Now in Sp flash tool select the scatter file which you have extracted from Partitions.zip and make sure that prealoder, lk, and lk2 is selected.
9) You don't need to select auth file as authorization is disabled. Once you do it, it should look like this. ALWAYS MAKE SURE DOWNLOAD ONLY MODE IS SELECTED! DON'T SELECT OTHER MODES!
Make SURE "Download Only" is selected. Don't select ANYTHING ELSE! You will lose your IMEIs, Serial Numbers, Capability of Hardware Attestation etc. if you choose "Format data + Download" make SURE you selected "Download Only".
10) Now, you can start downloading with the button and after that a checkmark will appear. You can reboot your phone
After flashing it should look like this. Download has been complete.
Credits:
B. Kerler for MTK Bypass
@Saksham Antil (aka Tony Stark) for original guide

Reserved for updates:
When Linux Version will be available for our devices it will be posted
Edit it looks like it is, only my who uses old source

Database Info

welcome