Related
im trying to crack the transformer open and do u think the back is glued on or is it screwed on? im thinking theres probrably some screws behind the lable but cant seams to find anything here that wont scratch it to remove it. hit me up with ideas and hopfully I can post some kind of video on how to dissacemble the transformer.
It will most likely be fastened with screws. I think if it had been glue peoples cases wouldnt be 'creaky'. There were some pics on a Chinese site showing it open. I saved them to my pc, If I find them I'll upload.
Edit: Well I found them but they're not really showing the case. I'll attach them anyways and you can see if they help or not. It looks like once you get the bezel off the back just slides clean off.
Ok well scratch screws under the asus logo, thanks very much for those pics. I already have the screws out from the bottom. I'm guessing the back seals with some type of clips
Looking at there tools in second picture seams they used a guitar pic to losses it from its edges
cowballz69 said:
Looking at there tools in second picture seams they used a guitar pic to losses it from its edges
Click to expand...
Click to collapse
Maybe try a credit card?
Ha tore up my room looking for my guitar pic lol. Ill try my credit card
When in doubt use a hammer.
stuntdouble said:
When in doubt use a hammer.
Click to expand...
Click to collapse
Lol, tryed to use a credit card but its to thick, going to stop at the store tomorrow and pick one up
cowballz69, pm sent
If you have one, your best bet is a Stanley knife (boxcutter, I think you call them). Should be thin enough, you'll just have to be careful not to nick any internal crap.
If it were me, I'd use a scalpel, but I know most people don't have one handy.
ok well heres my mini review untill i get a guitar pick, i got the bottom half to crack open with a credit card(to thick but i did it), i was then able to slide the card from one end to the other. The plastic clips holding the metal are very very crappy. the metal was extreemly easy to bend and by just putting the card threw the bottom was enough to bend it. i was however; able to put it back together with out making it look as if i opened it, but u would need a ULTRA Thin piece of plastic to complete the mission(DO NOT USE ANYTHING ELSE BUT PLASTIC,,THE METAL AROUND THE EDGE IS SUPER FRAGLE). seams all ASUS does is pop the plastic backing in and screw the bottom and its off to who every buys it.
(Losining the bottom screws lowerd the light bleed that was there by 30% ( i was a full brightness and back screen and loosining the screwes made a big impact so the issue with the light bleed is to much pressure on those areas)
seams this is easy enough just need the right tools.
cowballz69 said:
(Losining the bottom screws lowerd the light bleed that was there by 30% ( i was a full brightness and back screen and loosining the screwes made a big impact so the issue with the light bleed is to much pressure on those areas)
seams this is easy enough just need the right tools.
Click to expand...
Click to collapse
Interesting. That seems to be the very spot where my screen has a little backlight bleeding. I'll try it out in a few minutes.
Youtube it
If this is the fix. A youtube vid would be awesome. Ready set go
paleridr said:
If this is the fix. A youtube vid would be awesome. Ready set go
Click to expand...
Click to collapse
thats not the only spot i have light bleed, i also have bleeding on the top portion and theres no screw to losen so must be on to tight from the inside. however this does prove that the bleeding is from pressure not the screen itself
You need these spudgers,
http://www.dealextreme.com/p/professional-premium-precision-phone-disassembly-tool-7-piece-set-23050
Get a few sets (if you're planning on opening up electronics on a regular basis). These are soft plastic, and will wear out after a few uses. You don't want to use anything harder like a knife, as then you will mar the 'lips' on the device shells. Aesthetics aside, that will show up as evidence of tampering, meaning goodbye warranty.
Most electronics use plastic snap-in clips to hold the shells, along with screws and possibly soft glue. Going slow will prevent the clips from snapping off, but not always.
You can find these same tools on Amazon and eBay. Just search on 'spudger', which is their name.
Use the guitar pick to get the initial crease, push one of the thicker wedges into the crease, and slide it along the seam. This assumes you've gotten all of the (hidden) screws.
e.mote said:
You need these spudgers,
http://www.dealextreme.com/p/professional-premium-precision-phone-disassembly-tool-7-piece-set-23050
Get a few sets (if you're planning on opening up electronics on a regular basis). These are soft plastic, and will wear out after a few uses. You don't want to use anything harder like a knife, as then you will mar the 'lips' on the device shells. Aesthetics aside, that will show up as evidence of tampering, meaning goodbye warranty.
Most electronics use plastic snap-in clips to hold the shells, along with screws and possibly soft glue. Going slow will prevent the clips from snapping off, but not always.
You can find these same tools on Amazon and eBay. Just search on 'spudger', which is their name.
Use the guitar pick to get the initial crease, push one of the thicker wedges into the crease, and slide it along the seam. This assumes you've gotten all of the (hidden) screws.
Click to expand...
Click to collapse
breaking a clip is def possible in this case
How did you get the screws on the bottom off? Do you have the right screw driver (any ideas where I can get one)?
jrac86 said:
How did you get the screws on the bottom off? Do you have the right screw driver (any ideas where I can get one)?
Click to expand...
Click to collapse
it's a torx.
jrac86 said:
How did you get the screws on the bottom off? Do you have the right screw driver (any ideas where I can get one)?
Click to expand...
Click to collapse
Use a Torx T6 bit.
When you opened it up, was there anything to suggest there was any way Asus would know you had opened it up please (if you hadnt bent the bezel ofc) if you needed to send it back under warranty for some reason?
opening is not recomended threw my experiance * I used the thinnest guitar pic today*,and the metal around the edge;any slight flex and it ends up staying that way and wont go back on straight no matter how carefull u are, also the clips that hold the plastic back to the bezil is ULTRA CRAPPY to a point u have a 50 50 chance of it not holding the plastic cover anymore. ON the plus side; if u loosen the bolts in the bottom, u can relieve the light bleed there. so reguarding the light bleed its best to just send it back to ASUS to get it fixed.
MY Next step is having ASUS fix my light bleed on my own tablet and not have them give me a replacement.
I will be posting a before picture of the light bleed when i send it out , and a After picture on when i recieve it back from them. good idea??
OK, so today I threw my Incredible (AMOLED if it matters at all) into my backpack and some keys in there scratched it a little bit. The scratches are not too deep, and you can't feel them or anything, so I was hoping there might be a way to fix it. I looked around a little bit and saw that toothpaste can help for getting scratches out of things like CD's and such. Has anyone tried this on their phone? I don't think anything bad would happen, but I don't really know...
Also, I know that I should have bought a screen protector, so please don't remind me about that.
'Getting scratches out' sounds like a bit of a oxymoron. You don't have something IN your screen, a scratch is more like a bit of surface screen missing.
I can't see why toothpaste would harm the screen. Just don't get the phone wet, turn it off, clean up afterwards, etc.
Really can't see how it would help either...
I have never heard of using toothpaste to fix scratches, but since the scratches are not to deep I try this product that has done wonders it is called apple sauce and was originally made to fix iPod scratches. Look it up on amazon.
If this helped please press the thanks button
Yes! It works well, rub it in tiny little circles starting in the center of the screen and working your way out. BUT BE CAREFUL. don't push hard ar all, and don't do the same part more than 2 or 3 little "circles" or you may destroy the screen. if you do it right though, it should work fine.
Nilurun said:
Yes! It works well, rub it in tiny little circles starting in the center of the screen and working your way out. BUT BE CAREFUL. don't push hard ar all, and don't do the same part more than 2 or 3 little "circles" or you may destroy the screen. if you do it right though, it should work fine.
Click to expand...
Click to collapse
What do you mean "destroy the screen"? How easily can I accidentally do this? I don't want it to get worse!
They say you can do it on CD's it acts like a polish. I think it all depends on the surface of the screen and what kind of metirial it is made up of.
Good luck though!
Vaseline. lol
Yes, it will probably work since toothpaste is the same as a car polish in general
Sent out of my Free Candy Van.
Mustard works better than toothpaste. It turns into glass when you use it to remove scratches on your phones screen. If you rub it on your face every night before going to bed you'll grow a proper manly beard too. Really, there's no limit to the things you can do with mustard with it's amazing properties.*
*All of the above is patently untrue in the same way that turning lead into gold is pure fiction. Toothpaste contains mild abrasives. Would you use sandpaper on your screen?
DirkGently1 said:
Mustard works better than toothpaste. It turns into glass when you use it to remove scratches on your phones screen. If you rub it on your face every night before going to bed you'll grow a proper manly beard too. Really, there's no limit to the things you can do with mustard with it's amazing properties.*
*All of the above is patently untrue in the same way that turning lead into gold is pure fiction. Toothpaste contains mild abrasives. Would you use sandpaper on your screen?
Click to expand...
Click to collapse
Nice! I tried the mustard, and it looks like it worked! My screen looks brand new! Also, I think I can already see stubble after just one night!!! The only problem is now my pillow is stained yellow...
Anyways, I thought that the toothpaste helped because of the slight abrasiveness of it...?
There are products here in the UK made under the Duraglit brand as Brasso and Silvo. These are metal polishes, but are also available as a cotton wad roll impregnated with the stuff. I do not know if they are sold in the USA, but there may be something similar from US manufacturers. As their name suggests they are made to clean and polish brassware and silverware.
It is a very fine abrasive suspension, but it also contains ammonia to remove any tarnish, and white spirit to act as a lubricant. They are quite good at removing scratches from watch glasses etc., by gently cutting into the surface, down to the level of the scratch.
On touch screen devices, the touch screen sensitive layer lives above the screen glass, but under a plastic protective layer. It will be this top layer that you have scratched. The product above or something similar may work, but check that the white spirit does not attack the protective plastic layer.
As mentioned above small, circular movements, a little at a time may work. If you cut through the protective layer, you are in trouble.
patrick848 said:
Nice! I tried the mustard, and it looks like it worked! My screen looks brand new! Also, I think I can already see stubble after just one night!!! The only problem is now my pillow is stained yellow...
Anyways, I thought that the toothpaste helped because of the slight abrasiveness of it...?
Click to expand...
Click to collapse
Nice to see people getting into the spirit of things Anyway, i hope you find a solution that works. I personally might be tempted to ask the manufacturer to replace the digitizer, as long as the cost wasn't too prohibitive. I tried changing one myself on an old phone and it didn't work out too well
Am not sure about what kind of display cover your phone has. But, if it's capacitive or IR and the top layer is glass, take it to the local wrist-watch merchant/repair center and they could fix it for you using H2SO4 and some filler.
Alternatively, you can have the top layer of the touch panel replaced.
And, next time, do use a screen protector. =D
saintmagician said:
'Getting scratches out' sounds like a bit of a oxymoron. You don't have something IN your screen, a scratch is more like a bit of surface screen missing.
I can't see why toothpaste would harm the screen. Just don't get the phone wet, turn it off, clean up afterwards, etc.
Really can't see how it would help either...
Click to expand...
Click to collapse
I am not sure if toothpaste would help the screen scratches, its not a tooth scratch.. LMAO
Is it true that tooth paste works like sand paper on glass, does that mean that it contain something harder than glass? I don't have scratch just want to remove paint between my screen protector. Want to know if tooth paste actually micro scratch the glass.
I have a blue Verizon S3. I recently dropped it and it of course landed such that there are a few chips in two corners. The damage is just cosmetic, but I'd like to fix it if possible. My understanding is that the bezel is attached to the screen,requiring either a difficult bezel replacement or a complete screen replacement, but both of which I'd prefer to avoid.
So, my guess is that the best plan would be to fill in the chips (if necessary) with epoxy and paint over it with nail polish or paint. But I don't know what would be the best match.
Has anyone tried doing this and had success with a particular type of nail polish/paint?
Thanks.
My recommendation is to buy a case that covers the phone completely, you'll forget about it...
I have a Diztronic case arriving Wednesday, but need to use it with my car dock without the case. It's not a big deal, but given that its trivial to do (except for finding the right paint) I would like to do it.
Well you're definately right, a simple cosmetic fix would be best, here's your part...
Not sure what to tell you man, maybe someone will chime in with some info or similar experience... It's just cheap plastic...
I found this on eHow:
How to Repair Chipped Plastic
You can actually get the bezel separately for $17, but the screen needs to be heated to come off - not easy. Plastic repair is easier (as you pointed out) but a good job requires good paint. Hopefully someone has already tried.
Thanks for the suggestions.
I remembered this thread from cappy section... With people making modifications to their housings... possibly you can msg one of them...
dblevitan said:
I have a blue Verizon S3. I recently dropped it and it of course landed such that there are a few chips in two corners. The damage is just cosmetic, but I'd like to fix it if possible. My understanding is that the bezel is attached to the screen,requiring either a difficult bezel replacement or a complete screen replacement, but both of which I'd prefer to avoid.
So, my guess is that the best plan would be to fill in the chips (if necessary) with epoxy and paint over it with nail polish or paint. But I don't know what would be the best match.
Has anyone tried doing this and had success with a particular type of nail polish/paint?
Thanks.
Click to expand...
Click to collapse
did you ever find a solution to this problem? I just recently scratched my bezel on my s3 as well...
littlele87 said:
did you ever find a solution to this problem? I just recently scratched my bezel on my s3 as well...
Click to expand...
Click to collapse
It's all kitted up into one part... the solution is a $250 front part of the phone...
Repairing the bezel itself is pretty hard which is also attached to the metal frame of the phone.
You will need to heat up the screen/metal frame then take the screen off, there is a high risk you could damage the screen.
If you do so, you will need to purchase a new screen which is around $200-250
If you look on ebay, you can find some that are preassembled (screen + bezel + frame) for $250
emckai said:
Repairing the bezel itself is pretty hard which is also attached to the metal frame of the phone.
You will need to heat up the screen/metal frame then take the screen off, there is a high risk you could damage the screen.
If you do so, you will need to purchase a new screen which is around $200-250
If you look on ebay, you can find some that are preassembled (screen + bezel + frame) for $250
Click to expand...
Click to collapse
thanks for repeating exactly what i said an hour before...
emckai said:
Repairing the bezel itself is pretty hard which is also attached to the metal frame of the phone.
You will need to heat up the screen/metal frame then take the screen off, there is a high risk you could damage the screen.
If you do so, you will need to purchase a new screen which is around $200-250
If you look on ebay, you can find some that are preassembled (screen + bezel + frame) for $250
Click to expand...
Click to collapse
Make it easier on yourself next time, kid. Just copy/paste...
Sent from my rooted Mayan calendar
littlele87 said:
did you ever find a solution to this problem? I just recently scratched my bezel on my s3 as well...
Click to expand...
Click to collapse
I looked in some drug stores for some nail polish that would match, but never found anything. It's currently in a case, so I rarely notice it. Maybe sometime when I have energy, I'll try to replace the bezel, but not for now.
Well I cracked the glass on my Galaxy S3 and there is some other superficial damage around the bezel. As I am going to be getting another phone shortly anyway I was thinking about this problem and how I could get my phone as possible to "new." After consideration I'm leaning to using an automotive paint/scratch repair pen as opposed to nailpolish. Depending on how it turns out, I'll upload my process, materials, and pictures.
Alright, I did send sms on my bicycle which resulted in I did drop the phone on the ground. Luckily I had ad NILLKIN glass screen protector, which did save most of the phone . I have ordered a new Nillkin screen protector from Aliexpress. And I hope to patch up this phone so it looks good again. How would you have done ?
As you can see at the bottom in the pictures there is physically damage, you can you see the screen bleeding thru also the huwawei logo is damaged.
My idea is UNDER the NEW Nillkin screen protector I will try to mask these "holes" so the screen is not beelding thru anymore. What material should I use to patch up these holes.. also.. how to repar the logo ? can I print it out on my computer printer ? it might look **** on paper but UNDER the glass protector it might look a lot better.
All creative ideas are appreciated, I have high hopes the phone will look good again..
And hopefully my phone will surrive until the M8 release.
Just to let you know desipite the glass look damaged like this the phone is still fully functional!!
ouch i can feel with you.
How about some black film, black paper or everything else that is black and thin
Yes some black material for sure.. Black film would be perfect in guess.. Just wonder where to get it also some black glue at the sides also..
Maybe you can find a front replacement? - http://www.ebay.com/itm/New-Front-O...-Parts-For-Huawei-Ascend-Mate-7-/201270995814
http://www.ebay.com/itm/Original-Re...s-Lens-For-Huawei-Ascend-Mate-7-/141549809429
Don't put a huawei printed logo there lol it will look bad and cheap.
alexre123 said:
Maybe you can find a front replacement? - http://www.ebay.com/itm/New-Front-O...-Parts-For-Huawei-Ascend-Mate-7-/201270995814
http://www.ebay.com/itm/Original-Re...s-Lens-For-Huawei-Ascend-Mate-7-/141549809429
Don't put a huawei printed logo there lol it will look bad and cheap.
Click to expand...
Click to collapse
Nice man might be a very good alternative! But how easy is it to change it really?
Do I need a heat gun for that?
Don't know. I don't advise to do it yourself , just go with the phone to any service, I'm sure they know how to do the operation. Or maybe you have an huawei service near you.
Or...if you have the courage go for it ) - https://www.youtube.com/watch?v=nDiaQOzCvfE & https://www.youtube.com/watch?v=lUl8dCuhBGw
Joke man, don't do it yourself if you don't have experience
alexre123 said:
Don't know. I don't advise to do it yourself , just go with the phone to any service, I'm sure they know how to do the operation. Or maybe you have an huawei service near you.
Click to expand...
Click to collapse
I have done some smartphone repair myself, I changed the USB board on my old Galaxy Note 1.
I bought a smartphone repair kit with a few tools and very small screwdrivers. To change the glass is probably not much harder, but I need to know if I need a heat gun since I do not own any yet Hopefully it is not needed..but I would assume so...
I might also add the reason I bought a screen protector was that the original glass underneeth have a small crack too that goes accross the entire screen but it s quite invisible besides from certain angels.. so to change that screen to would actually be amazing..and it would make the secondary value when I sell this when M8 is released be a lot higher..
I think you need one. Look at the second yt movie at 22:34. Have an hair dryer?
https://meta.ifixit.com/Answers/View/3523/Using+a+hairdryer+instead+of+a+heat+gun
Hair Dryer vs Heat Gun
https://www.youtube.com/watch?v=9ELHDYjpLoc
If I was me I would go with the phone to a service. Anyway good to know Nilkin tempered glass do the job, I have one also on my screen
alexre123 said:
I think you need one. Look at the second yt movie at 22:34. Have an hair dryer?
https://meta.ifixit.com/Answers/View/3523/Using+a+hairdryer+instead+of+a+heat+gun
Hair Dryer vs Heat Gun
https://www.youtube.com/watch?v=9ELHDYjpLoc
If I was me I would go with the phone to a service. Anyway good to know Nilkin tempered glass do the job, I have one also on my screen
Click to expand...
Click to collapse
Yes the Nillkin glass did its job but I think I was unlucky, that the bottom of the phone got under my bicycle tire.. it felt like it...
I recommend Nillkin, IT has very good Oleophobic coating, which makes the whole device a lot more enjoyable to use, but be careful whren you put it on non 100% straight surfaces it will slip onto the floor.
Alright it is more or less decided I will buy a new front cover with glass, I will make sure to get original parts with gorilla glass. Since the ebay link you linked to are chipped from china I guess I can just order straight from alixpress instead...
I have heard singapore post have quite fast shipping compared to china post.
just one question is hard to see in the videos.. but do I really need to disassembly every component all the circuits boards just to change the front screen ? do I need to open the case at all when using the heat gun/hair dryer ?
If as in the every component and circuit board has to be disassembled it is over my competence probably... unless I am super careful..
Mutch better if you want to purchase an original front to replace it. Don,t know if you really need to take all the components of for replacing the front screen, but you can make some research on it or you can ask on other forums, maybe are others with more experience.
yes I understand..must decide tomorrow then.. because of shipping times a fast decision need to be made otherwise I will have to wait too long..
blackinfinity said:
yes I understand..must decide tomorrow then.. because of shipping times a fast decision need to be made otherwise I will have to wait too long..
Click to expand...
Click to collapse
Man I was repairing the whole Mate7 from the scratch!
If u shattered the screen ;
1.You will need new one which cost £40-£60 2.You will have to strip the WHOLE phone which is pain!
3.You will have to open the back cover,which is very hard process.You will need hard force to pop back cover from hinges.(first you need to remove small bottom cover which is plastic.)You will have to pry it underneath is adhesive which holds that small cover firmly.
4.Once you manage to remove back cover you have to disconnect all flex cables.There are 3 black screws and 4 chrome screws(smae like two at bottom) which holds motherboard.
There is small black cover which covers all connectors and it is tricky to remove it,because left side is kind of locked under chrome metalic cover plate! You need to pry it slightly to the right to flip it upwards.Be careful! One black screw holds that small black plate!
Once you remove the motherboard, another and very very hard part awaits you!
5.Removing the battery!
You will need heat gun to remove battery but even that heat gun might ot help you to remove BIG battery without damage !!
I tried to remove battery without damage but no luck.So I will advise you to buy new battery for mate7 mine cost me just £8 from china but I had to wait almost a month to deliver! Disaster shipping from china!
So if you apply lot of heat you might be lucky remove battery without damage.
But I was scared to apply too much heat on battery it could result in explosion or fire!!!
So I rather purchased one.
Once you remove battery, you can remove bottom part of phone which is usb board with speaker and plastics. It is up to you you dont need to remove it.
6.Removing the damaged screen from (middle) supporting frame!
This can be easy depends how screen is damaged. BUT
Here you have 2 options to replace screen.
A:You can buy screen without supporting frame which is harder and more work and heat gunning around the screen and prying screen from middle frame.Needs like 30-40 seconds of heating around the screen not in the middle.
B:You can buy s reen with middle frame which is very easy.Screen is already fited in frame so you dont need to mess with very slim adhesive srtips around the screen(which I done)
Then you will have to remove all parts from middle frame. Ear speaker ,loud speaker usb board and replace it to new housing.
Once you will set the new screen you can put all parts back together..
Replacing screen for this phone is PAIN!
It really needs skills and be careful because it is very easy to scratch back cover.
XDADEVX said:
Man I was repairing the whole Mate7 from the scratch!
If u shattered the screen ;
1.You will need new one which cost £40-£60 2.You will have to strip the WHOLE phone which is pain!
3.You will have to open the back cover,which is very hard process.You will need hard force to pop back cover from hinges.(first you need to remove small bottom cover which is plastic.)You will have to pry it underneath is adhesive which holds that small cover firmly.
4.Once you manage to remove back cover you have to disconnect all flex cables.There are 3 black screws and 4 chrome screws(smae like two at bottom) which holds motherboard.
There is small black cover which covers all connectors and it is tricky to remove it,because left side is kind of locked under chrome metalic cover plate! You need to pry it slightly to the right to flip it upwards.Be careful! One black screw holds that small black plate!
Once you remove the motherboard, another and very very hard part awaits you!
5.Removing the battery!
You will need heat gun to remove battery but even that heat gun might ot help you to remove BIG battery without damage !!
I tried to remove battery without damage but no luck.So I will advise you to buy new battery for mate7 mine cost me just £8 from china but I had to wait almost a month to deliver! Disaster shipping from china!
So if you apply lot of heat you might be lucky remove battery without damage.
But I was scared to apply too much heat on battery it could result in explosion or fire!!!
So I rather purchased one.
Once you remove battery, you can remove bottom part of phone which is usb board with speaker and plastics. It is up to you you dont need to remove it.
6.Removing the damaged screen from (middle) supporting frame!
This can be easy depends how screen is damaged. BUT
Here you have 2 options to replace screen.
A:You can buy screen without supporting frame which is harder and more work and heat gunning around the screen and prying screen from middle frame.Needs like 30-40 seconds of heating around the screen not in the middle.
B:You can buy s reen with middle frame which is very easy.Screen is already fited in frame so you dont need to mess with very slim adhesive srtips around the screen(which I done)
Then you will have to remove all parts from middle frame. Ear speaker ,loud speaker usb board and replace it to new housing.
Once you will set the new screen you can put all parts back together..
Replacing screen for this phone is PAIN!
It really needs skills and be careful because it is very easy to scratch back cover.
Click to expand...
Click to collapse
ehhm... good luck OP
XDADEVX said:
Man I was repairing the whole Mate7 from the scratch!
If u shattered the screen ;
1.You will need new one which cost £40-£60 2.You will have to strip the WHOLE phone which is pain!
3.You will have to open the back cover,which is very hard process.You will need hard force to pop back cover from hinges.(first you need to remove small bottom cover which is plastic.)You will have to pry it underneath is adhesive which holds that small cover firmly.
4.Once you manage to remove back cover you have to disconnect all flex cables.There are 3 black screws and 4 chrome screws(smae like two at bottom) which holds motherboard.
There is small black cover which covers all connectors and it is tricky to remove it,because left side is kind of locked under chrome metalic cover plate! You need to pry it slightly to the right to flip it upwards.Be careful! One black screw holds that small black plate!
Once you remove the motherboard, another and very very hard part awaits you!
5.Removing the battery!
You will need heat gun to remove battery but even that heat gun might ot help you to remove BIG battery without damage !!
I tried to remove battery without damage but no luck.So I will advise you to buy new battery for mate7 mine cost me just £8 from china but I had to wait almost a month to deliver! Disaster shipping from china!
So if you apply lot of heat you might be lucky remove battery without damage.
But I was scared to apply too much heat on battery it could result in explosion or fire!!!
So I rather purchased one.
Once you remove battery, you can remove bottom part of phone which is usb board with speaker and plastics. It is up to you you dont need to remove it.
6.Removing the damaged screen from (middle) supporting frame!
This can be easy depends how screen is damaged. BUT
Here you have 2 options to replace screen.
A:You can buy screen without supporting frame which is harder and more work and heat gunning around the screen and prying screen from middle frame.Needs like 30-40 seconds of heating around the screen not in the middle.
B:You can buy s reen with middle frame which is very easy.Screen is already fited in frame so you dont need to mess with very slim adhesive srtips around the screen(which I done)
Then you will have to remove all parts from middle frame. Ear speaker ,loud speaker usb board and replace it to new housing.
Once you will set the new screen you can put all parts back together..
Replacing screen for this phone is PAIN!
It really needs skills and be careful because it is very easy to scratch back cover.
Click to expand...
Click to collapse
Hello and thanks, I appreciate your detailed instructions.
But I need to say one really IMPORTANT THING
IT IS NOT THE SCREEN THAT I NEED TO CHANGE THE ACTUAL SCREEN AND LCD IS WORKING PERFECTLEY WHAT I NEED TO CHANGE IS THE Front Screen Outer Glass Lens. i HAVE HIGH HOPES THAT IF I ONLY CHANGE THIS I DO NOT NEED TO DO ALL THE INSTRUCTIONS YOU DO SINCE I AM ONLY CHANGING THE GLASS NOT THE ACTUAL SCREEN, IT IS A VERY IMPORTANT DIFFERENCE BETWEEN SCREEN AND OUTER GLASS AND FRONT. I HOPE YOU WILL READ MY POST AND GIVE ME AN UPDATE BEFORE I PUSH THE BUY BUTTON THANKS!
This is the part I was going to order it is just the glass no lcd screen.
blackinfinity said:
Hello and thanks, I appreciate your detailed instructions.
But I need to say one really IMPORTANT THING
IT IS NOT THE SCREEN THAT I NEED TO CHANGE THE ACTUAL SCREEN AND LCD IS WORKING PERFECTLEY WHAT I NEED TO CHANGE IS THE Front Screen Outer Glass Lens. i HAVE HIGH HOPES THAT IF I ONLY CHANGE THIS I DO NOT NEED TO DO ALL THE INSTRUCTIONS YOU DO SINCE I AM ONLY CHANGING THE GLASS NOT THE ACTUAL SCREEN, IT IS A VERY IMPORTANT DIFFERENCE BETWEEN SCREEN AND OUTER GLASS AND FRONT. I HOPE YOU WILL READ MY POST AND GIVE ME AN UPDATE BEFORE I PUSH THE BUY BUTTON THANKS!
This is the part I was going to order it is just the glass no lcd screen.
Click to expand...
Click to collapse
Sorry but you are like 10 year old child..
So u wanna change your ''front Screen Outer Glass Lens'' ??? (that is damn long name for glass )
You have so much hopes ? OK .. go on .. I leave you to it ..
I wish you very best of luck ..
''''IT IS A VERY IMPORTANT DIFFERENCE BETWEEN SCREEN AND OUTER GLASS AND FRONT''
DDDDDD this was so funny :laugh: :good:
Fingers :fingers-crossed:
You was talking about changing the lcd not only the front Glass. I just wanted to make sure you need to do all the instructions to change only front glass. The lcd is working..
blackinfinity said:
You was talking about changing the lcd not only the front Glass. I just wanted to make sure you need to do all the instructions to change only front glass. The lcd is working..
Click to expand...
Click to collapse
And I will give you one last advice ; that my detailed post above I explained you how difficult it is .. YOU want to change glass only ??
And what you think, you can just do it without stripping phone apart ?? Are you magician ? You would have to open phone anyway !
And replacing glass on your screen, do you have any idea how you gonna do it? Removing glass from LCD is x10 TIMES hard that my instructions above man !
So you basically adding even more, harder work to hard work ..!
Do you even have
1.LCD separator heat machine ??
2.Cutting line wire ??
3.Cleaning alcohol chemicals ??
4.Optical clear adhesive glue ??
5.Ultraviolet curing lamp ??
Come oon man ...
I told you I wish you very best of luck..
This guy want to do the exact same thing - https://www.youtube.com/watch?v=O8HNBtl9MwI
You have the all process here - https://www.youtube.com/watch?v=nDiaQOzCvfE & https://www.youtube.com/watch?v=lUl8dCuhBGw
Take a look and decide if you want do it yourself and risk to mess things up or go with the phone and the replacing part to a service and let someone who did this before.
Just got the s5 from a family member..great phone..the bezel is chipped quite heavily .. the replacement part seems cheap enough but I don't know if it's worth the risk..maybe just case it up and be done with it..
russy23 said:
Just got the s5 from a family member..great phone..the bezel is chipped quite heavily .. the replacement part seems cheap enough but I don't know if it's worth the risk..maybe just case it up and be done with it..
Click to expand...
Click to collapse
Your best bet for a guide to follow that also has images is on the following link.
https://www.ifixit.com/Device/Samsung_Galaxy_S5
Good Luck!
~~~~~~~~~~~~~~~
I DO NOT PROVIDE SUPPORT VIA PM UNLESS ASKED/REQUESTED BY MYSELF.
PLEASE KEEP IT IN THE THREADS WHERE EVERYONE CAN SHARE
russy23 said:
Just got the s5 from a family member..great phone..the bezel is chipped quite heavily .. the replacement part seems cheap enough but I don't know if it's worth the risk..maybe just case it up and be done with it..
Click to expand...
Click to collapse
No, it isn't if you've never done this before.
Reasons are the next:
1. The risk to damage LCD-assembly is very high.
2. The risk to buy a non-suitable bezel (middle frame, or "rear case" how Samsung calls this part) is very high. They are different for different variants of S5 and contain different main antennas inside gray plastic.
Your best bet is to wait for a crack in the screen. You're also gonna screw up the adhesive around the screen and you could literally break keys underneath (no backlight anymore)
Unless you can pop in a nail and try to lift up the screen yourself... as it happens when device is old.
As of now new Original screen is around 100€, which is one of the best display today.
I'll just stick a case on and be done with it..just get a new charge port cover and that'll do..haha
I just installed a new charger port cover. Cost me $3.50 and took 5 minutes to install.. If you really want to change the bezel do a google search on how to do it.. There are plenty of videos which will show you the steps..
russy23 said:
Just got the s5 from a family member..great phone..the bezel is chipped quite heavily .. the replacement part seems cheap enough but I don't know if it's worth the risk..maybe just case it up and be done with it..
Click to expand...
Click to collapse
after watching several instructional videos on how to disassemble my s5, i realized its not worth it. they water-proofed the crap out of it with multiple layers of adhesive. using a heat gun to soften the glue is a pain, and can also damage the components.
if you use some kind of very soft heat gun and a "sucker" while sliding in a small credit card, you can do it. it is all about being delicate...
The bad thing to replace the bezel frame is that you have to unmount the whole phone, and at last remove the screen. It's glued to the frame with an adhesive band and it's very difficult to remove it without breaking it. And probably you'll need a new adhesive to mount it again to the frame, otherwise parts of the screen will remain elevated from the bezel.
And it's very easy to break the AMOLED screen connector between the mainboard and the screen if you don't know where it is. First, you'll have to watch several youtube vids to get to know how to disasemble the phone and where the connector is.
And if you dare to replace it and you fail, there're cheap alternatives like this: https://lltrader.com/collections/s5/products/samsung-galaxy-s5-display-assembly-no-frame but it's not an original AMOLED, it's a LCD and very fragile, keep it in mind.