ood evening friends, I ask for your support, I need to load prl to a kyocera c5170 achieved and enable mobile boss, set sid, nid, number, min etc, and I have the spc too, here my problem is that I want to load prl using QPST or workshop but neither reconose the device in my file manager detects KC02US KYOCERA USB serial port, but I never detected any program to work the equipment and charge prl, could explain the correct procedure please, for your attention to my fellow post thank you very much.
Related
hello i have a problem with the change of carrier x.x
i use QPST because i cant use CDMA WORKSHOP because i dont buy it $99 0.o
qpst detect xoom but with the wrong ESN: 7FFFFFFF
when i select in qpst "service programming" i select xoom and then i "read from phone" now i have charged the info and i change the info that i need change
now i "write to phone" and then the ESN change for the real ESN ( i know that is the real because i use CDMA WORKSHOP to watch my ESN)
however the "write to phone" didnt cancel and still charging when the charging finish the xoom disconnect and connect and the ESN still 7FFFFFF and the phone number dont change and when i "read from phone" this charge the old info the verizon info... im trying but i have the same result...
someone please helpme
hello? someone help me x.x
Hi! Are you from Mexico ? What QPST version are you using ?
helloo yeah im from mexico the qpst version is 2.7 build 362
I have Samsung Mesmerize I500.04
Build SCH-I500.EI20
Firmware Version 2.3.5
I'm using CDMA Workshop 3.8
Debug mode is activated.
I Installed Samsung Kies (Will not recognize phone)
At first the phone was recognized in CDMA Workshop and my only problem was being unable to get the SPC....
Now, CDMA workshop says 'phone failed to respond' and wont read anything!
Ive tried factory reset..
Ive tried re-installing drivers
resetting phone, and computer...
idk what else to do!!
I need to know how to make CDMA recognize the phone and then i need to retrieve the SPC as well so that I can make changes to the phone.
Any help would be greatly appreciated.
kevinjmckenzie said:
I have Samsung Mesmerize I500.04
Build SCH-I500.EI20
Firmware Version 2.3.5
I'm using CDMA Workshop 3.8
Debug mode is activated.
I Installed Samsung Kies (Will not recognize phone)
At first the phone was recognized in CDMA Workshop and my only problem was being unable to get the SPC....
Now, CDMA workshop says 'phone failed to respond' and wont read anything!
Ive tried factory reset..
Ive tried re-installing drivers
resetting phone, and computer...
idk what else to do!!
I need to know how to make CDMA recognize the phone and then i need to retrieve the SPC as well so that I can make changes to the phone.
Any help would be greatly appreciated.
Click to expand...
Click to collapse
What exactly are you trying to do? if your just trying to reprogram the phone and it is attached to your line just USCC made it so all you have to do is *228 and it will automatically provision itself. I cant think of another reason why you would possibly want the spc code. I dont visit this forum often anymore so if you want a quicker reply go through my profile i guess to send message.
Still need help!
I PM'd you. Anyone else who has any ideas?
UPDATE: I just need to know how to make the phone respond to CDMA Workshop.
pmd you back... are you sure you have appropriate drivers installed?
is your phone in modem mode and dial up?
bought cdma workshop nov. 2011, free upgrade until nov. 2012. interested in transfering the license to you please leave a private message
I lost the ability to send text messages and make/receive phone calls (but data is fine-email, web, etc) after flashing LiquidSmooth RC9(first I didnt have wireless-rebooted and had wireless and then lost my mobile) from CleanRom 5.0--I'm assuming I lost my IMEI. I tried using the IMEI repair tool but when I select the COM port my phone is on and press "Connect", the program locks up and I get a "Not Responding." I tried the tool on three different Windows computers. I do have a backup of a .qcn file(at the time that was the only method mentioned here).
Should I be good to go if I use the QPST method? Or should I go back to stock and unrooted and ask Verizon for a new SIM card?
Thanks. Any help would be appreciated. And yes I have searching through the forum help/answers but I dont know why the tool is not responding. In the video it connects instantaneously...
I want to flash the Pantech Breakout to work on PagePlus. I have rooted it with CWM recovery and read this thread for instructions to flash the Thunderbolt
http://forum.xda-developers.com/showthread.php?t=1294179
So far, I have,
-Verizon Pantech Breakout, clean, no issues
-New unactivated Verizon LTE sim card (if necessary)
-CDMA Workshop 3.9.0 demo
The questions I have are,
1. How to enter Diag mode in the Breakout?
2. To activate a new phone on PagePlus, it requires an ESN or MEID number. How can I get it before I place the activation? Can CDMA workshop identify the MEID number?
3. To acquire 3G data, I read somewhere that it might work if I obtain the MIN # from PagePlus after activation and use CDMA to write it. Is this correct?
4. Will there be a problem if the MEID # starts with 99000?
Any other roadblocks to consider?
Thanks for any help.
Rooted, but need to flash to PP
Can anyone help?
Ok ok... I would help but mimited data so let me hit up my man jason here. Not sure what he'll charge you
Sent from an Apple killing JellyBean
ota looping with sim card
I need help too. The sim card won't provision and keeps the 3G from working. I can see the signal in the signal meter menu but I cannot get the phone to think it's provisioned. That's where I'm stuck. HELP!!!:crying:
Gtalk me @ [email protected]
Sent from an Apple killing JellyBean
3G data needs
moparfreak426 said:
Ok ok... I would help but mimited data so let me hit up my man jason here. Not sure what he'll charge you
Sent from an Apple killing JellyBean
Click to expand...
Click to collapse
Ok, I used CDMA Flasher to flash to Page Plus 3 months ago. Verizon just issued an OTA update and I need to flash Page Plus again (I have also blocked future OTA updates). My problem is that I only had 1g data. I want to reflash with 3G data. CDMA Flasher support says they are working on 3G data for Page Plus, but it's not ready yet. Will it ever be ready? I don't know. How to flash Pantech Breakout to Page Plus (originally Verizon) with 3G data?
I have a boost moto G XT1031 flashed to Verizon XT1028. I upgrade the bootloader to 41.19 and flashed CM12.1. Everything was fine except that I couldn't make outbound calls. After reading a post about someone with similar situation, I flashed KK 4.4.4 radio XT1028_Verizon_US_CDMA_390.81.01P.zip. But after that all my information under SIM Status and IMEI Info were lost. Now it just says NO SIM Card.
How do I restore it? I have tried to use DFS but after CM12.1 was installed the PC won't install COM ports for the phone so it can't be recognized by DFS.
Any help would be greatly appreciated.
Thank you.
UPDATE: I managed to install stock KK 4.4.4 and now I am back to be able to receive calls, but not making outbound calls. Also, I can now connect to it using DFS. But I have no idea what to change in DFS. My phone #, MIN, MEID are back, but my PRL is wrong. It's 61010 but I think it's supposed to be 5xxxx something. Also, Network is Unknown and Mobile network type is Unknown. When I dial *228 it says "the number or code you dial is incorrect, please check the code and try again."
Since now I can use DFS, what can I do to make it work on Verizon/PagePlus again?
Thank you.
kliu888 said:
I have a boost moto G XT1031 flashed to Verizon XT1028. I upgrade the bootloader to 41.19 and flashed CM12.1. Everything was fine except that I couldn't make outbound calls. After reading a post about someone with similar situation, I flashed KK 4.4.4 radio XT1028_Verizon_US_CDMA_390.81.01P.zip. But after that all my information under SIM Status and IMEI Info were lost. Now it just says NO SIM Card.
How do I restore it? I have tried to use DFS but after CM12.1 was installed the PC won't install COM ports for the phone so it can't be recognized by DFS.
Any help would be greatly appreciated.
Thank you.
UPDATE: I managed to install stock KK 4.4.4 and now I am back to be able to receive calls, but not making outbound calls. Also, I can now connect to it using DFS. But I have no idea what to change in DFS. My phone #, MIN, MEID are back, but my PRL is wrong. It's 61010 but I think it's supposed to be 5xxxx something. Also, Network is Unknown and Mobile network type is Unknown. When I dial *228 it says "the number or code you dial is incorrect, please check the code and try again."
Since now I can use DFS, what can I do to make it work on Verizon/PagePlus again?
Thank you.
Click to expand...
Click to collapse
Bump c'mon need help
byrneout420 said:
Bump c'mon need help
Click to expand...
Click to collapse
byrneout420, if you are still having the same problem, this is how I got mine working again. I have another Moto G so I use DFS to save its PRL file to the hard drive, then connect the broken Moto G, and load that PRL file to it. After that I was able to do *228 to restore phone function. Eventually I got CM 12.1 installed and everything works including 3G. During the process, I made MIN, PRL, MEID, etc. disappear again several times, but I never went back to DFS. I just reflash the radio zip, and flashed it several times in a row - I saw this on the forum where someone mentioned to flash the radio zip several times to make it work.
Hope this helps.