Database Info

Fuze Problem (Help)

My Fuze got a wet.
I shook out the water
I powered it on. It came on and everything.
It reset itself.
Then I played with it for a while.
Everything seemed fine until I hit the power button. The screen turned off.
I pressed it again and it wouldn't turn on.
Nothing gets the phone back on at this stage, except taking the battery out and powering up again.
I then decided to do the bowl of rice thing and let it sit for about 7 hours.
It is still the same. If I press the power button at the top of device, it turns off.
If I press it quickly after, it turns back on but if I wait a while, lets say 3-5 seconds, it doesn't turn back on.
Also, the water damage sticker has turned light pink, like 65% of it.

any suggestions

I'm afraid there is probably no help. Even if the water dried completely before turning it back on the impurities in the water probably will cause problems.
I had one drop in some water. Powered it off, disassembled it and dried completely. I let it sit for 8 hours, reassembled it and powered it on. It worked for a couple of hours.
Luckily I had insurance on it.

oh ok
what about warranty, i am still covered
the little white box is still white but mostly pink

its kinda crazii that it turns on and everything works
its just that if i turn off the phone or it turns off automatically due to the power settings, it can't turn on.
the soft reset doesn't work and the power buttton atop the phone doesnt work either

w0w!!!
i just powered on my waater damaged 8525 from 2 yrs ago (had a tilt & fuze since) & it works!!!
b4 it would turn on but the screen wouldnt work
you would have to position it @ a certain angle in order to make anything out
it works now, besides needing to hooked up to the charger in order to load up
fuze is still sitting in a bowl of rice
any more ideas, suggestions...etc

ok, i just realizedthat the soft reset button @ da bottom doesnt function @ all
any idea on how to go about fixing this??
itsjust the screen doesnt come back on but device isnt off because the scroll wheel lights still show up
but it shouldnt because the device isnt charging

Can you warranty a device if the sticker is partially pink?

You can try the warranty, but when they see the water sticker is colored, you're likely to be charged for the cost of the phone. Water won't be covered by warranty, only insurance.
If you want to avoid replacing the phone at your cost, then about the only thing I can think of doing is pulling the battery out and cleaning it thouroughly with distilled water (in other words, another dunking). Do that 2-3 times with fresh distilled water to get rid of as many impurities from the other water as you can. Then let it dry for 24-48 hours (getting some dessicants wouldn't hurt to suck out as much water as you can). Then put a battery in and see what happens.
Odds aren't good this will improve things, but it's possible. It's more likely you'll need to get your hands on a new phone.

You could also try to find a broken fuze online, maybe eBay, but no water damage, and swap stickers.

thanks guys
do the silica packs count?
how would you go about switching the stickers?
is there a particular part i can switch from a used fuze to fix my problem?

wutitizshorty said:
thanks guys
do the silica packs count?
how would you go about switching the stickers?
is there a particular part i can switch from a used fuze to fix my problem?
Click to expand...
Click to collapse
For the sticker, just carefully take it off a different Fuze, hell maybe even a different phone as long as the sticker fits. Take off the pink one on your Fuze and glue on the new one. Should be good as new.
As for swapping parts, it would probably be too much money and trouble to do that, that'll void your warranty right there anyways and there's a chance you'll never assemble the phone back perfectly. Trust me, it has happened to me a lot when I thought I could swap parts.

I've seen a friend of mine do something with one he got wet that actually worked ... he dipped his entire phone in a bowl of rubbing alochol for a few seconds - the pulled it back out & let it dry out for about 24 hours and it's worked. Obviously take the battery out when you do that....

kinda scared about the rubbing alcohol because the phone works for the most part, just not the reset button
i have other devices so im gonna try the sticker swap for now

well the concepton the alcohol dunk is that you need alcohol that is as close to pure alcohol as possible. rubbing is great as previously mentioned. what it does is that it takes the water and vaporizes with the water. the same concept as adding wine or spirits into a soup. it makes the soup thicker and creamier because there is less water in it.. and it also can be used to fix a situation where you use too much water or something....

potential long term damage?...

Yesterday my phone got wet, the screen is howing some kind of wet spot under in, but heres the thing?
At the edges it seems the water damage is lightening the screen, yet in the middle theres a dark shadowy patch!
Any advice is great thanks?

take the battery out put the phone at a bowl with a dry rice give it a 48 hours
and your phone will be like new (tried a lot of times)

roytev said:
take the battery out put the phone at a bowl with a dry rice give it a 48 hours
and your phone will be like new (tried a lot of times)
Click to expand...
Click to collapse
This. Do this.
And do not delay.
If the phone works at all now it's because you're lucky and the water didn't get to anything sensitive yet. But the key word is 'yet'. It only takes a drop of water on a circuit board to ruin the device. If you don't have any rice at home right now, turn the phone off and pull the battery out NOW. Then go get rice. Don't leave the phone on to go to the store. The sooner the power is off, the better.
What happens is that the board gets slightly wet and when electricity is introduced there's a short. And tiny little circuit boards aren't designed to deal with electrical shorts. It hurts them. Badly. And quickly. And irreparably.
So taking the battery out is key as there's still electrical power in part of the circuits when the power to the phone is off. (Something's got to be polling the power button to know what to do when it's pressed. Something has to regulate the charging that works when the power is off, etc)What the rice does is creates a very dry environment by absorbing moisture.
In 2 days the rice will have sucked the water right out from under the screen.
And once you put it in the rice, don't touch it. Don't test it. Don't fuss with it. Just leave it there for 2 days and use another phone.

jamiee6610 said:
Yesterday my phone got wet, the screen is howing some kind of wet spot under in, but heres the thing?
At the edges it seems the water damage is lightening the screen, yet in the middle theres a dark shadowy patch!
Any advice is great thanks?
Click to expand...
Click to collapse
DO NOT RUN YOUR PHONE IF IT GETS WET. PULL THE BATTERY RIGHT NOW.
Even if your phone gets wet it is usually only damaged by running it after it is wet. If you let your phone dry for a few days it should be fine.

Thanks for the advice, that much i was already aware of - it was the dark area that appeared on the screen.
I have had the phone back on and run it with the screen max brightness and the dark patch has almost gone theres 2 small dots that are slightly lighter.
I will see what its like tomorrow.

jamiee6610 said:
Thanks for the advice, that much i was already aware of - it was the dark area that appeared on the screen.
I have had the phone back on and run it with the screen max brightness and the dark patch has almost gone theres 2 small dots that are slightly lighter.
I will see what its like tomorrow.
Click to expand...
Click to collapse
It should go away completely. I got mine where it was dark all the way around,and a fairly large spot in the middle. I just left my phone off four 24 hours, then used it, the spots were still there, but they went completely away.
Sent from my HTC Sensation 4G using XDA

[Q] moto g fell in water

my moto g fell in water. it is not working. will it come under warranty . if not how much it costs for repair..........................................

I believe that all manufacturers state in their standard warranty that water damage is not covered. If you take the rear cover off and take a look towards the bottom, you'll see there's a small red mark that indicates water damage. If this is present, you're out of luck with regards to an in-warranty repair.
My suggestion would be to store the phone in a container with dried, brown rice, for two days. Perhaps place the container on top of a radiator or similar heat source, to speed up the evaporation process. You don't want to induce too much heat to further damage the device.
Also possible is a bag of silica gel crystals that you usually get in pairs of shoes - place this in an airtight container with the phone and they'll soak up some moisture.
My girlfriend recently dropped the Moto G in water and within two days it was fully repaired, now works perfectly. Don't give up on it yet!

Got similar problem, my daughter drop her Motorola into bath. Left to dry for more than day next to boiler. Now not turning on, when plug charger LED flash white and goes off. After few seconds again and again just flashes and no more.
Thinking that battery gone as manage to turn on phone after incident and spotted that battery was on 0%.

bartmw said:
Got similar problem, my daughter drop her Motorola into bath. Left to dry for more than day next to boiler. Now not turning on, when plug charger LED flash white and goes off. After few seconds again and again just flashes and no more.
Thinking that battery gone as manage to turn on phone after incident and spotted that battery was on 0%.
Click to expand...
Click to collapse
plug it into the charger and hold the power button for 2-3minutes. then leave it charging for an hour and than try to turn it on.

Put it in a bowl of uncooked rice and cover it, leave it there for 2 days. It's serious, check YouTube if you don't believe it. It works, it dries the water out!
Sent from my XT1032 using xda app-developers app

This is the easiest way
Just get some dried rice and put your moto g/any phone dropped in water in a container and close it.Let it in there for overnight and tupp your pgone is alright

Moto Go falls into closet.
This happened yesterday noon. It was submerged for around 6-8 secs b4 I pulled it out. It looked like it was working fine. Nevertheless I took off the cover and tried drying it with a towel before I switched it off. (Total time till here 30-40 secs). Being quite an impatient guy, I turned it on after a few mins. (Let's say under 10 mins so far). It turned on with no problem. As calls were to be made, I dialed a number. As I heard the ringing on the other side, I assumed all was fine. But tht was not yet to be. Notice me saying yet?! Yes, this one has a happy ending.
Moving on. The person on the other end of the line could not hear me other than in short bursts, like having a 1 sec break/pause in between conversations. I tried calls with the speaker phone switched on. But it kept turning off and on again between the ringing. I switched it off and took out the sim. I did not do that the first time (Very foolish of me). It was clearly damp. I went on to dry it with a towel. I turned the phone bck on. Calls were made but the same issues persisted. I tried playing some music but it would stop right after it started. This was where I started to get a bit worried. I took off the cover and vigorously swung/waved the phone about trying to force out any excess water. The effort was not futile. The song continued playing. I immediately make a call but the break was still very much there. This went on till late evening.
Before the day was over, everything was working fine. There were lags but tht was there when I bought the phone (28/05/14). I used a 4S before this, so forgive if I seem a bit harsh. Tht too was dropped in a river, drenched with curd milk and submerged in beer. It still worked fine till a guy snatched it from me.
Cheers!
PS: I did not have access to a blower/dryer or any rice but that is the way it should be done. I'm just posting here so those who don't have tht around might get a confidence boost. Hope this helps.

Adam Outler had a pretty good video about this. It basically said to remove power ASAP (i.e. open up the phone and disconnect the battery) and submerge everything in high purity ethyl or isopropyl alcohol to displace the water and dry it out much faster.

Moto g Accedentally dropped in water
Hi,
I own a moto g which accedentally dropped in water. i took it off and it was working fine for few min. After some time i noticed some water inside my screen and my touch was not working. I left my phone for some time. After an hour when i restarted my phone my touch was working. To dry down the water, i kept my phone under shady sun light for about 2 hours. Now when i try to switch it on the led light is blinking 3 times as if it do when the battery drains. I tried to charge my phone and now the LED light is blinking and later it stopped.
If my circuits are crashed will the LED light blink. Because i used my phone before if completely dried off.

Hi , I dropped my moto g2 in to water tub ...It took a few seconds before I took it out ... Then i dried it for about an hour in sun light and kept it switched off for about almost a day .... Now it works fine but some time it gives sound like water in a hot pan..... Any suggestion would b much appreciated... Thanks in advancr

Water Damaged Phone, Help!

Hey!
So On Saturday I dropped my phone down the toilet by accident, i removed it from the toilet, after about 5-10 seconds, and it was still on, it seemed fine, so I was like ohh okay...i dried it ect ect and it was working fine, but some parts of the touch wasn't working so I left it on as i could not switch it off. On that night i dried it with the hair dryer as well, didn't work, so wrapped it in a towel and but it in the boiler cubard to keep warm for around 12 hours maybe more...tried to switch it on and it didn't work again.
the day later (Sunday) decided to take it apart, and dry the insides, still wasn't working, but the notification light is on and sometimes flickers so i slept with it under my pillow as it would keep warm over night, on Monday, i put the charger in and the screen came on to that battery charging screen for around 5-6 seconds and it said it was on 0%....the notification light was still on.
I Put the phone in some rice in a box, wrapped it in a towel and left it in the boiler cubard again until Wednesday, afternoon....
what can i do?? will this work?? how much would it cost to get fixed?
is the touch screen broke? do i need new battery? ect ect
THANKS!

Best thing to do if you get a phone wet is turn it off and leave it off for at least a week. The problem is that moisture gets inside the phone itself and just takes time to evaporate. If you turn it on or leave it on after water gets in you run the risk of shorting something out and killing the phone (which is what sounds like happened). As far as repairing it is concerned, might as well get a new one, it'll cost less.

your phone should survive just give it some time in the rice, my brothers samsung ace went through something similar and he put it in rice and it was fine after a day buried in it, there is videos of the moto g submerged in water for a while and still works fine
good luck

Water Damage OP0

Hello All,
I mistakenly placed my OPO in a small puddle of water last Friday morning (3 days ago) and I didn't notice the damage done till the screen started flickering and that's when I noticed the water strains under the screen..Phone calls wouldn't go and the phone shutdown eventually. I searched around and somebody on this forum mentioned they put their phone in a rice bag for a few days after being damaged by tea.. ..that's exactly what i did on Friday evening- placed it in a rice bag and semi sealed it.
It lay in the rice bag till today morning and I intermittently checked couple of times on saturday and Sunday.. Yesterday I noticed that the red light was blinking and the phone would vibrate in my hands upon pressing the power button(under charge). That was the case till now, but just half an hour ago, the battery started charging and i could seen the white charge indicator! When it charged to about 5 %, I tuned it on and everything seems to work - the screen, phone calls, data, wifi..
But I still see the water strains under the screen. Do you recommend that I start using it again or does it need the rice bag treatment for some more time?
I tried removing the back cover to disconnect the battery but I was just not able to..
Thanks for the help guys- and thanks for the suggestions in some of the other threads that I followed.
Regards,
Tej

My opo accidentally submerged into sea water twice... but it survived