Database Info

Update Samsung Galaxy FIT S5670 with Official Gingerbread DDKT1 2.3.6 Firmware

pre Requisites:
- All the data present in your Galaxy FIT needs to be backed up ONLY by following the below mentioned steps so as to ensure that just in case if the data gets lost or corrupted.
- Charge left in the device should be minimum 60% so as to make sure that the phone doesn’t get turned Off in the middle of firmware update. Enable the USB Debugging in your device from the path “Settings > Applications > Development > USB debugging”
So,assuming that you have followed all the instructions mentioned above you now need to proceed further for procedure.
Procedure to Update
- Download Gingerbread 2.3.6 Package & odin-beni-ss.dll for Fit.zip in your computer after which you need to extract the same.If Promted For Password then You Should Enter Password as “sampro.pl”.
For 2.3.6 Update Package- http://hotfile.com/dl/140199372/0b98375/GT-S5670_INU_S5670DDKT1_S5670ODDKT1_S5670DDKT1.rar.html
- Match the extracted files from the below shown screen capture, even if single file is missing then you need to check with the extraction or download process.
- From extracted files, open Odin executable file and turn Off the phone so as to enter the device in the download mode.
- Now, you need to enter the by holding the Volume Down button + the Home key button (the middle button). While holding these both buttons, you need to switch ON your device. Just in case if the device boots in the normal mode then you will have to again try the process of entering into the download mode
- After entering the phone in the download mode, connect the device to the computer while keeping the Odin opened. Within a minute, the ID : COM section will turn yellow which will mean that all the drivers have been successfully installed and you are now ready to proceed to the next step.
- Click on the “OPS” option in the Odin to select the below mentioned file, tick on “One Package” option and then select the One Package option as mentioned below.
OPS – BENI_v1.0.ops
One Package – S5670DDKT1_S5670ODDKT1_S5670DDKT1_HOME.tar.md5
- Click on Start and then wait for the device to get restarted. Once the device gets restarted, you will be asked to enter the Google Account credentials. Once you see the home screen in your phone, disconnect the connected phone.
Congratulations!!! You have successfully update ur android with 2.3.6 Gingerbread Firmware
_______________________________________________________________
Press THANKS button If I help U in any manner

Hi!
Does this firmware includes greek language?Thanks!

may be no...
Because DD is for india:thumbup:
Sent from my GT-S5670 using xda app-developers app

Do you know where i can find or what is the name for the firmware to search?Also i have a greek galaxy fit with 2.3.6,do you know how to make a full backupo of this firmware?Thanks!

i guess everyone knows this

zafisinl said:
Do you know where i can find or what is the name for the firmware to search?Also i have a greek galaxy fit with 2.3.6,do you know how to make a full backupo of this firmware?Thanks!
Click to expand...
Click to collapse
http://www.sammobile.com/firmware/
In search write s5670.

password
what is the password for this file????

It's witten over there on sammobile
Sent Via XDA™ Premium

Password
rajmi said:
what is the password for this file????
Click to expand...
Click to collapse
Read the first post carefully
Pasword : sampro.pl

The rar file just has the md5 file, where can I find the other files? I tried manually downloading the files from different locations but it just sits at downloading mibib and doesn't do anything. The flashing process just sits at downloading MIBIB and doesn't go anywhere, I have tried waiting for as long as 30mins, now the mobile doesn't even start with the previous firmware. When started it shows an icon like connection problem between a computer and mobile right after the initial samsung logo and sits there.Please help

zafisinl said:
Hi!
Does this firmware includes greek language?Thanks!
Click to expand...
Click to collapse
Most probably it does.I flashed mine with a stock russian rom.the phone started in russian but you can easily navigate through the icons to settings and change the language.I turned it to greek

[How To] Install Jellybean 4.1.2 +Root

Install XXLPY Android 4.1.2 Jelly Bean Firmware on I9070 Galaxy S Advance
LINK-
http://www.hotfile.com/dl/187838919/fd98d34/I9070XXLPY_I9070SERLPY_SER.zip.html
STEPS-
Android 4.1.2 Official Firmware
1.Extract Firmware zip file that you downloaded already from above link, you will get a .tar file and some other files.
2.Extract Odin zip file and you will get Odin3 v3.07.exe along with few other files.
3.Power off your phone. Wait 5-6 seconds for vibration to confirm complete switch off.
4.Now, put the Galaxy S Advance I9070 phone in Download Mode by pressing pressing and holding down the Volume Down and Home buttons while pressing the Power button until you are welcomed by a green robot indicating you are in Download Mode.
5.Now run Odin3 v3.07.exe (see Step 2) as an Administrator because Admin privileges is required to complete the process smoothly.
6.Now connect your Galaxy S Advance GT-I9070 with your PC using USB cable. A message will arrive under Odin’s message box in the bottom left saying “Added!!”. If you don’t get the same then you should try another USB port (try USB port located in back in your desktop PC). If that too don’t work then you should then reinstall the driver. If you successfully see the “Added!!” message in Odin then you are ready to go in next step. You should also see COM port with a number in Yellow if you successfully added your device.
7.Select these files in Odin at respective buttons from extracted I9070XXLPY firmware folder :
a)Click the PDA Button, and select the .tar file here with *code* appearing in its name
8.in Odin window, make sure Auto Reboot and F. Reset Time checkboxes are selected. Also, make sure that Re-Partition checkbox is selected, only if you are using a .pit file (see Step 7.4).
9.Double check everything that we mentioned in Step 7 & Step 8 above. Now, once satisfied hit the START button to begin the flashing process.
10.Once flashing completed, the phone will reboot automatically and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can then unplug the USB cable to disconnect your device from computer.
NOTE-If you have PARAMETER ERROR delete.md5,extension should end with .tar and put it in PDA.
ROOT(by shaaan)
How to :
1. Download the zip and place it in the root of your sd card.
PS : SD Card is a must.
2. Reboot to the stock recovery.
3. Select install update from external storage.
4. Select the root.zip file.
5. Viola
Enjoy your rooted JB.
LINK- http://d-h.st/ook

Thread already there under general.
http://forum.xda-developers.com/showthread.php?t=2086965
Reported.

hmm
thats was not a proper guide,
you edited it later.

Perform a factory reset after booting 4.1.2 ... else you will get "Insert SIM card" error.

Thread closed, its pretty much the same as this one >>> http://forum.xda-developers.com/showthread.php?t=2086965

Tuto : install Galaxy S7 Edge Nougat firmware

Your dreams are now reality!
You can install Nougat easily on your Galaxy s7 edge!!
1)Download Odin 3.12.3 .zip file and run/open Odin3 v3.12.3.exe file from the extracted files on your PC.
2)Download the Nougat firmware for your device from the downloads section above, and unzip the .zip file to get the files starting with AP, CSC, Home_CSC, BL and CP in the beginning of their name.
3)Enable OEM unlock on your phone:
Go to Settings » About phone » and tap Build number seven times to enable Developer options.
4)Go back to main Settings page, scroll to bottom and select Developer options from there.
Under Developer options, look for Enable OEM unlock checkbox/toggle and enable it.
5) Boot your device into Download mode:
Switch off your device.
Press and hold “Home + Power + Volume down” buttons for a few seconds until you see a warning screen.
Press Volume Up on the warning screen to accept it and boot into Download mode.
6) Once your device is in download mode, connect it to the PC with a USB cable. The Odin window on PC should detect the device and show an “Added!!” message.
7) Now we’ll select each firmware file (from files we got in Step 2 above) into the appropriate box in Odin.
Click on CSC tab and select the firmware file starting with HOME_CSC in its name.
└ Note: Do NOT select the regular CSC file that starts with CSC in its name, as that would replace your CSC and thus would result factory data reset of the device.
Click on CP tab and select file starting with CP in its name.
Click on BL tab and select the file starting with BL in its name.
Click on AP tab and select the file starting with AP in its name.
└ Note: DON’T play with any other options on Odin the screen. You’re only required to connect your device and select the firmware files as instructed above.
Click the Start button on Odin and wait for it to finish the process. Once it has finished successfully, you’ll see a pass message on the Odin screen.
8) Your device will automatically reboot when Odin is done flashing. You can then disconnect your device.
└ It might take some time for the first boot after flashing a stock firmware.
That’s it. Your Galaxy S7/Galaxy S7 Edge is now rocking Android Nougat update.
9) enjoy
-------------
download section
-------------
Odin : http://www.theandroidsoul.com/download-odin/
firmware : http://downloadmirror.co/1KtK/G935FXXU1ZPK4-thanks-samfirm.net.zip
Source : http://www.theandroidsoul.com/download-galaxy-s7-and-s7-edge-nougat-firmware-odin-tar/

Thanks, but there are already multiple discussions on this.
EG the dedicated Nougat thread: https://forum.xda-developers.com/s7-edge/how-to/android-7-0-s7-edge-uk-beta-program-apk-t3493696

Experience Flashing Galaxy S6 Stock Rom

My phone currently will not boot, cannot enter recovery and I can only access Odin. From my research so far I've been getting fairly mixed results as to whether flashing the stock s6 rom will erase my photos (which is what Im trying to recover).
I'm considering flashing now but I was wondering if any of you have had experience with flashing the samsung galaxy s6 using a stock rom via Odin and whether it deleted your photos from your gallery.

bump

If your device SM-G920F;
Download and run this;
https://forum.xda-developers.com/attachment.php?attachmentid=3803841&d=1467715462
When you open the program, type the values given here;
Model: SM-G920F
Region: PHN
Auto: Selected
Manual: Unselected
Binary Nature: Unselected
Check CRC32: Selected
Decrypt automatically: Selected
When you write and select options given above, press "Check Update" and then press "Download" to download full firmware for your device.
Once the download has been finished, extract the zip file that you've downloaded via SamFirm.
After unzip it, download and run this;
https://forum.xda-developers.com/attachment.php?attachmentid=3804544&d=1467772303
When you open it, press AP and select file which starts with G920 from downloaded (from Samfirm) and extacted zip folder.
When you set the file to Odin, press and hold volume down + home button + power button until you see a warning screen on your phone. When you see it, release the buttons and press volume up button once. You'll see a big android logo and big "Downloading..." text.
Connect your phone to your PC in download mode (the "Downloading..." screnn) and click "Start" on Odin.
When you see "PASS" text on Odin, disconnect the cable.
This method will reflash the firmware of your device WITHOUT messing any personal data on your device.

hi, how are you? I'm also trying to flash the stock rom on a SM-G920F but I get the following error when I follow your steps:
SamFirm v0.3.6.0
Could not fetch info for SM-G920F/PHN. Please verify the input or use manual info

Cacha21 said:
hi, how are you? I'm also trying to flash the stock rom on a SM-G920F but I get the following error when I follow your steps:
SamFirm v0.3.6.0
Could not fetch info for SM-G920F/PHN. Please verify the input or use manual info
Click to expand...
Click to collapse
It's working just fine for me;

Will this work on the SM-G920W8? as that's what my model is. More specifically G920W8VLU2AOG2

You have to download too:
Microsoft Visual C++ 2010 Redistributable Package (x86)
and
Microsoft Visual C++ 2008 Redistributable Package (x86)

Update Samsung Galaxy On5 SM-G550FY (non-Pro) to Nougat Pro firmware - Detailed

As one of the previous threads in this section mentioned the same (that On5 Pro firmwares work on non-Pro On5 models also), I can confirm that it works on Samsung Galaxy On5 SM-G550FY (2015 non-Pro) model. The downloaded firmware was a latest On5-Pro Nougat version that I could find on https://updato.com but works with old non-Pro On5 model as well.
This post is "only" meant to chalk out the complete process.
Detailed instructions for people who've not rooted their Samsung devices before:
Steps to replicate the process:
Preparation for rooting first:
Make sure your phone battery is charged to 70% or more
Backup your device data
Make sure you install Samsung's Android USB Driver for Windows on your PC, if you haven’t already. >> Official link
Download the latest .tar image of TWRP for Galaxy On5 (it is compatible) >> Official link
Download and Unzip the latest version of Odin version >> Official link
Download the latest Super SU >> Official link
Now follow the instructions:
First you should enabled Developer options. If Developers Option is hidden, go to Settings > About Phone > Built Number (tap on it for 5-8 times)
Enabled USB Debugging and OEM unlock.
Install Android USB Drivers on your PC.
Connect the phone to you PC using the USB cable and copy the SuperSU.zip file into any directory of your internal storage.
Turn off your Samsung Galaxy Boot the device into Download Mode as follows: press and hold Volume Down, Home and Power buttons together.
When a warning triangle appears on screen, press Volume Up button to enter Download Mode.
Launch Odin.exe by click right and run as administrator on computer.
Connect your phone to the computer. Odin will automatically detect your phone and show the “added" message.
In Odin, tap AP button and find the TWRP Recovery file you downloaded earlier and select it.
Uncheck Auto-reboot in the options tab in Odin
Click Start in Odin.
Once the root installation is done, your phone will reboot and soon a PASS message with a green background appears in the left-most box at the very top of Odin.
Remove the battery and then re-insert it again.
Boot into “recovery mode”, by pressing and hold Volume Up + Home +Power buttons simultaneously
In the TWRP mode Swipe to Allow Modification
Tap ‘Install’
Select Storage and scroll to location of SuperSU.zip file.
Select the .zip file and swipe the bar to confirm. This will start flashing the .zip file.
Once the flashing finished you will see the ‘Reboot System’ option, click it to reboot your device.
After reboot, if the SuperSU App exist on your Application Menu on your smartphone it means you’ve successfully rooted your device.
Can take further help from here (works for this On5 model as well) >> https://forum.xda-developers.com/sa...nt/updated-root-instructions-samsung-t3747435
After rooting:
You can remove the bloatware first using any "root uninstaller" app from the Play Store. Be careful as to not uninstall any vital system apps.
Now go to >> https://updato.com and download the latest On5 SM-G550FY firmware (>1GB) by searching "On5" and sorting firmwares by date and selecting the region (for my model make the region was India (INS) >> You can use this Working link directly, as well
The above version is an On5 Pro Nougat version but works in old On5 models as well.
Final Steps:
Now again launch Odin.exe by click right and run as administrator on computer.
Connect your phone to the computer. Odin will automatically detect your phone and show the “added" message.
In Odin, tap AP button and find the firmware file you downloaded earlier and select it. You might need to first extract the firmware file.
Click Start in Odin.
The phone will reboot and you'll have updated your Lollipop/Marshmallow device to Nougat.