Related
help pls problem with root on p6200
when i was root by this way i have issue
1) Install USB driver for Samsung Galaxy Tab 7.0 Plus to transfer files between the Android device and computer.
2) Enable USB Debugging Mode on the tablet to connect the Android device with the computer and use the Android SDK with it. [Press Menu>> Settings>> Applications. From there navigate and click on Development option and ensure the USB Debugging Mode is turned on.]
3) As the tutorial might wipe all data of the phone, create a backup. If the device is having any custom recoveries such as CWM/TWRP already installed then backup data using the recovery.
4) The device should have above 80 per cent of battery charge.
5) The Galaxy tablet should be factory unlocked and not locked to a particular carrier.
6) The tablet will lose manufacturer's warranty once it is rooted. However, users can reclaim the warranty back by unrooting the device later.
7) The recovery file and the Superuser file work only on the Samsung Galaxy Tab 7.0 Plus P6200. Applying these on any incorrect variant might brick the device. Therefore, verify the model number of the Galaxy device by selecting Settings>> About device>> Model number.
Steps to root Samsung Galaxy Tab 7.0 Plus GT-P6200 on Android 4.1.2 Jelly Bean and Install CWM Recovery
Step-1: Download CWM recovery file for Samsung Galaxy Tab 7.0 Plus to the computer
File name: GT-P6200-Recovery-tar.md5
Step-2: Download CWM flashable SuperUser zip. Copy it to the SD card of the tablet
File name: Superuser-3.1.3-arm-signed.zip
Step-3: Download Odin 3.07 and extract the downloaded zip to the computer
Step-4: Switch off the Galaxy tablet and boot it into Download Mode by pressing and holding Volume Down and Power buttons together
Step-5: Launch Odin on the computer
Step-6: Connect the Galaxy Tab 7.0 Plus to the computer using USB cable while it is in the Download Mode. Wait until Odin detects the tablet. When the tablet is connected successfully, the ID: COM will turn yellow with COM port number. Also, an Added message will appear in Odin indicating successful connection
Note: If the Added message does not come then try another USB port, try the one located at the back side of the computer. If that too does not work then re-install USB driver.
Step-7: In Odin, click the PDA button and select GT-P6200-recovery.tar.md5 file
Step-8: Verify the Auto Reboot and F.Reset Time checkboxes are selected in Odin. But uncheck the Re-Partition option
Step-9: Finally click the Start button in Odin to begin the installation process which would take few minutes to complete. Once the installation process is completed, a PASS message will appear under Odin indicating successful installation. The tablet will then reboot automatically
Step-10: Once the tablet boots up, turn it off. Then boot the device into recovery mode by pressing and holding Volume Up and Power buttons together
Note: In recovery mode, use the Volume keys to scroll between options and use Power button to select the desired option.
Step-11: In recovery mode, scroll down to and select install zip from sdcard then select choose zip from sdcard. Now navigate to the Superuser-3.1.3-arm-signed.zip file which was earlier copied to the SD card of the tablet
Step-12: Select it using the Power button and confirm installation by selecting Yes on the next screen
Step-13: Once the installation process is completed, return to the main recovery menu and reboot the tablet by selecting reboot system now
Samsung Galaxy Tab 7.0 Plus should be now rooted successfully on Android 4.1.2 Jelly Bean with ClockworkMod recovery installed. To verify the root, open the app drawer of the tablet and look for an app called SuperSU from the list. Also, to ensure the root access, install Root Checker app from Google Play Store.
when select Superuser-3.1.3-arm-signed.zip says
e:failed to verify whole-file signature
e:failed to verify whole-file signature
e:signature verification failed
thats all
plz hlp me
can somebody with a recovery that I can mode to run on my phone help? I am tired of using 360root.apk I want to use SuperSU and not these apps with Chinese interface
Here are the steps I followed after some extensive reading of other peoples methods and trying every possible app that would not work:
How to install TWRP and root the Samsung Galaxy J1 Mini (SM-J105F)
The device is powered by a Spreadtrum chipsets and Android 5.1.1
Basically what you need to do to root your Samsung, is to install/flash a custom recovery such as TWRP, which other than the limited functions of the OEM recovery, has all the features you need to flash a custom rom. You then boot into this TWRP recovery and use the touch menu to install/flash the SuperSu xx.zip file to give you root. It seems that other methods to root do not work on this specific phone.
Here is an Odin3 flashable *.tar md5 TWRP file that will also make it possible to root your Samsung Galaxy J1 SM-J105F, unfortunately it has to be paid for. Find it here: http://www.saroms.co.za/product/samsung-galaxy-j1-mini-j105f-root-file/ - and follow the bellow steps to flash the TWRP custom recovery and after rooting your J105F Samsung Galaxy J1 Mini.
Note: Odin3 only flashes with xxxx.tar or xxxx.tar.md5 files. TWRP can also flash xxxx.zip files.
To get into Odin mode or Download mode on the phone, switch off phone and unplug any cable to your PC or charger. Now hold in the Home button, the lower part of the volume button (V-) and the power button simultaneously. The phone will boot into a recovery screen and if you push the top part of the volume button (V+) you will switch to the Download screen. Only now can you plug your phone into the PC and run Odin3
Once TWRP recovery has been loaded, do the following to boot into TWRP recovery: Disconnect any cables to charger or PC. Switch off the phone. Now hold in the Home button, the upper part of the volume button (V+) and the power button simultaneously. The phone will boot showing the Teamwin screen and then the menu buttons which work from the touchscreen.
If you do not want to pay for the correct TWRP recovery for your specific device, then use Google to search for the file: TWRP SM-J105H_F_M_Y 5.1.1.tar
1. Download the following files:
(i) OEM Samsung firmware for your phone in case you have to fall back and reinstall the firmware i.e.
XFV-J105FXXU0AQA3-20170329071250.zip
(ii) TWRP SM-J105H_F_M_Y 5.1.1.tar or any other custom TWRP recovery file for your model phone.
(iii) UPDATE-SuperSU-v2.79-20161211114519.zip
2. Go to Settings > About device > Software Info > and tap on Build number a few times until you are a developer.
3. You should now see and tap on 'Developer options' if you go back to Settings.
4. In Developer options. turn on 'OEM Unlock' by moving the slider to the right, Enable. Never set that setting to off once you have loaded a custom firmware or TWRP custom recovery! You phone will brick and only show *“Custom binary blocked by FRP lock” after the next reboot!! (FRP = Factory Reset Protection)
* If so install OEM firmware with Odin3 and start again.
5. Copy the UPDATE-SuperSU-v2.79-20161211114519.zip file to the root of your internal storage SD card (not external). This will be installed by using TWRP recovery. Use your PC to do this.
6. Turn the device off and boot into "Download Mode” (V- and Home and Power ... and then V+)
7. Run the Odin3 application on your PC and load the recovery *.md5 file under 'AP' or load the file: TWRP SM-J105H_F_M_Y 5.1.1.tar.
8. Connect the MS-J105f to your PC and let Odin3 connect and ID:COM will go blue and show i.e. 0 : (COM4) > then click Start.
9. The SM-J105F will power on when done. Disconnect cable and power it off again.
10. Boot into recovery (V+ and Home and Power) will now boot into TWRP.
11. You will now see the TWRP menu touch screen.
12. Tap Install > scroll to the "UPDATE-SuperSU-v2.79-20161211114519.zip" file you downloaded and copied to the phone memory tap it.
13. Swipe at the bottom slider to confirm install.
14. Tap Reboot to system when done and you should be rooted.
15. Install and run SuperSU from the app store and run.
16. Install and run Root Checker Basic.
To reinstall the OEM firmware, download the proper xxxx.zip from the Samsung website.
You must the extract the xxx.tar.MD5 file from the download
If you can get into the Download screen on your SM-J105F then use Odin3 as above, just under PA select the OEM file xxxx.tar.MD5 (it takes a short while to select properly as it a very large 2 gb file after extracting)
Hope this helps someone else. Thanks to all whose posts and contributions helped me.
Your dreams are now reality!
You can install Nougat easily on your Galaxy s7 edge!!
1)Download Odin 3.12.3 .zip file and run/open Odin3 v3.12.3.exe file from the extracted files on your PC.
2)Download the Nougat firmware for your device from the downloads section above, and unzip the .zip file to get the files starting with AP, CSC, Home_CSC, BL and CP in the beginning of their name.
3)Enable OEM unlock on your phone:
Go to Settings » About phone » and tap Build number seven times to enable Developer options.
4)Go back to main Settings page, scroll to bottom and select Developer options from there.
Under Developer options, look for Enable OEM unlock checkbox/toggle and enable it.
5) Boot your device into Download mode:
Switch off your device.
Press and hold “Home + Power + Volume down” buttons for a few seconds until you see a warning screen.
Press Volume Up on the warning screen to accept it and boot into Download mode.
6) Once your device is in download mode, connect it to the PC with a USB cable. The Odin window on PC should detect the device and show an “Added!!” message.
7) Now we’ll select each firmware file (from files we got in Step 2 above) into the appropriate box in Odin.
Click on CSC tab and select the firmware file starting with HOME_CSC in its name.
└ Note: Do NOT select the regular CSC file that starts with CSC in its name, as that would replace your CSC and thus would result factory data reset of the device.
Click on CP tab and select file starting with CP in its name.
Click on BL tab and select the file starting with BL in its name.
Click on AP tab and select the file starting with AP in its name.
└ Note: DON’T play with any other options on Odin the screen. You’re only required to connect your device and select the firmware files as instructed above.
Click the Start button on Odin and wait for it to finish the process. Once it has finished successfully, you’ll see a pass message on the Odin screen.
8) Your device will automatically reboot when Odin is done flashing. You can then disconnect your device.
└ It might take some time for the first boot after flashing a stock firmware.
That’s it. Your Galaxy S7/Galaxy S7 Edge is now rocking Android Nougat update.
9) enjoy
-------------
download section
-------------
Odin : http://www.theandroidsoul.com/download-odin/
firmware : http://downloadmirror.co/1KtK/G935FXXU1ZPK4-thanks-samfirm.net.zip
Source : http://www.theandroidsoul.com/download-galaxy-s7-and-s7-edge-nougat-firmware-odin-tar/
Thanks, but there are already multiple discussions on this.
EG the dedicated Nougat thread: https://forum.xda-developers.com/s7-edge/how-to/android-7-0-s7-edge-uk-beta-program-apk-t3493696
Hi! After struggling in rooting my C9 pro (SM-C9000, TGY) due to the lack of a proper guide, I decided to provide my guide to the community.
Of course, I don't take responsibility for damages etc. etc. Read the entirety of the guide before doing anything.
Useful shortcuts: Holding down power+volume down for a couple seconds force reboots from almost anywhere. Vol up+home+power while booting boots into recovery. Vol down+home+power boots into download (odin) mode.
Step 1) Fetch the required files(sorry I can't post direct links):
Nougat 7.1.1 firmware from sammobile
Oreo 8.0 firmware from sammobile
Odin https://www.xda-developers.com/update-firmware-any-samsung-phone/
Magisk Manager https://www.xda-developers.com/how-to-install-magisk/ (The link that says "Download the latest Magisk Manager APK here")
ADB https://www.xda-developers.com/install-adb-windows-macos-linux/
CROM Service apk from apkmirror
Step 2) Prepare the files
Unlock developer options on your phone by spamming Build Number in Settings> About Phone> Software Information. Enable USB debugging from developer options. Connect your phone to your PC via cable. Extract ADB (platform-tools) on your desktop (or other location). Extract Oreo firmware. There should be 5 files. Copy the one that starts with AP into platform-tools folder. Open the platform-tools folder. Hold down shift and right click inside the folder. Choose "Open PowerShell window here" from the context menu. Type or copy-paste
Code:
.\adb devices
to start ADB. On your phone, check "always allow on this PC" and click OK when prompted. Enter the code again and check if a device appears on the list. Then type
Code:
.\adb push AP_C9000ZHU1CSC1_CL14667562_QB22709761_REV00_user_low_ship_MULTI_CERT_meta.tar.md5 /sdcard/
.(Change the name of the file corresponding to yours. You can change the destination to another folder in your phone. Ex. /sdcard/download/) This will transfer the file from your PC to your phone. Do not drag and drop the file. This might corrupt it, causing a bootloop upon installiation. (Happened to me initially. Recovered & used the push command to get it to work.). Transfer Magisk Manager's apk to your phone or download it directly from your phone(you can drag and drop this one, as it won't install if corrupted(it won't corrupt)). Install Magisk Manager on the phone(Enable sideloading if asked). In the app, touch the topmost install button and touch install again in the next screen. You will have two options: "Download zip only" and "Select and patch a file". Choose "Select and patch a file", then locate the AP file you transferred to the device. Magisk manager will patch the file and generate magisk_patched.tar in /sdcard/download/. In ADB, type
Code:
.\adb pull /sdcard/download/magisk_patched.tar
This will transfer it to the platform-tools folder. Again, don't use windows explorer to transfer. That will most certainly corrupt the file.
Step 2.5) Backup
Backup your data (you can use smart switch desktop program paired with mobile app to backup most of the stuff). Remove your google account from the device.
Step 3) Install Nougat 7.1.1
Extract Nougat 7.1.1 firmware. Extract odin. Run Odin.exe (might have version in name). Click OK. Factory reset your phone (You can do so from settings or recovery mode.). After the reset, reboot into download mode. It will ask if you're sure you want to install unofficial software, choose continue (If I don't recall incorrectly, the button for that was vol up). Plug your phone into your PC. Odin log should say "added!!" and you should see your device in one of the rectangles above. Now select the tar.md5 files extracted from the 7.1.1 firmware. Click the BL button, locate the BL_etcetc.tar.md5 file, click open. It will check the md5 for a second then let you click the next button. After choosing the BL(bootloader), AP(system), CP(radio) and CSC(localization) files (USERDATA button should remain empty, HOME_CSC file has no use) make sure only F.reset time and auto reboot are selected in options. Click start to begin. After flashing, it will do another factory reset and show you the setup.
Step 4) Unlock Bootloader
Skip everything in setup, then unlock develper options and you should see "OEM Unlocking" option that was removed in OREO firmware in there. Enable it. Next transfer the CROM service apk to your device (or download it directly). Install the app. Open it. Unlock the bootloader. (This step is required because C9000 is a Chinese phone)
Step 5) Install Oreo again
Boot into download and connect to odin. You can use the reset button to empty the buttons. Now select BL, CP and CSC files from the extracted oreo firmware. For AP, choose magisk_patched.tar . Start. If the installiation fails, you didn't unlock the Bootloader properly. The phone will reboot and factory reset a couple times. When it boots up, you'll have magisk installed.
Step 6) Things to do after rooting(optional)
First of all, magisk can hide root from Google, but not Samsung. Samsung Health, Knox secure container, Maximum power saving mode and Samsung pay won't work after you root. NFC will keep turning on on its own unless you uninstall Samsung pay. A samsung package (I'm not sure about the name but I think it was security log agent) will keep sending an unblockable notification offering to unroot. Uninstall that too, and you'll have a stable experience.
Recovering from fails:
If download mode refuses to install because of unofficial binaries, the bootloader isn't properly unlocked. Wait a couple seconds and force reboot with the key combination. Since it couldn't flash the system, that should reboot back to download mode (or recovery. in that case, choose "reboot to bootloader"). Install the official firmware, unlock bootloader and try again.
If the magisk_patched.tar file gets corruped and you flash the corrupted file successfully, your device will get into a bootloop. After the install, odin orders the phone to reboot into recovery to factory reset, but since the system image is corrupted, it won't be able to boot and produce a kernel panic. This will cause the phone to reboot, which will fail and cause it to try to reboot again. Since the phone doesn't get past the splash screen, this bootloop cannot be interrupted by button shortcuts. You should wait for the battery to die out for the bootloop to end. (It should take a day at max. Wrap a towel around it to block the vibration sounds if you want) After battery gets depleted, you need to perform a quick maneuver. You should plug the phone into a power supply (preferably your computer) while holding down volume down+home+power buttons. If you do it right, it will boot into download mode. (Otherwise, it will bootloop again. Simply unplug, wait for it to stop and try again) Flash the official firmware and repatch the AP file. Just in case you run into this issue, I recommend having less than 10% charge in your phone while flashing, just to make the wait time shorter.
Important: Check your firmware's baseband version from settings before flashing. In C9000ZHU1CSC1, CSC1 is the system and U1 is the bootloader version. Compare the bootloader version to the firmware you're going to flash and make sure they match. You can't downgrade bootloader versions. Flashing a previous version will brick your phone. (Probably permanently) This shouldn't be an issue since sm-C9000 has only one bootloader version, but check it anyways just to be sure.
Lojcs said:
Hi! After struggling in rooting my C9 pro (SM-C9000, TGY) due to the lack of a proper guide, I decided to provide my guide to the community.
Of course, I don't take responsibility for damages etc. etc. Read the entirety of the guide before doing anything.
Useful shortcuts: Holding down power+volume down for a couple seconds force reboots from almost anywhere. Vol up+home+power while booting boots into recovery. Vol down+home+power boots into download (odin) mode.
Step 1) Fetch the required files(sorry I can't post direct links):
Nougat 7.1.1 firmware from sammobile
Oreo 8.0 firmware from sammobile
Odin https://www.xda-developers.com/update-firmware-any-samsung-phone/
Magisk Manager https://www.xda-developers.com/how-to-install-magisk/ (The link that says "Download the latest Magisk Manager APK here")
ADB https://www.xda-developers.com/install-adb-windows-macos-linux/
CROM Service apk from apkmirror
Step 2) Prepare the files
Unlock developer options on your phone by spamming Build Number in Settings> About Phone> Software Information. Enable USB debugging from developer options. Connect your phone to your PC via cable. Extract ADB (platform-tools) on your desktop (or other location). Extract Oreo firmware. There should be 5 files. Copy the one that starts with AP into platform-tools folder. Open the platform-tools folder. Hold down shift and right click inside the folder. Choose "Open PowerShell window here" from the context menu. Type or copy-paste to start ADB. On your phone, check "always allow on this PC" and click OK when prompted. Enter the code again and check if a device appears on the list. Then type .(Change the name of the file corresponding to yours. You can change the destination to another folder in your phone. Ex. /sdcard/download/) This will transfer the file from your PC to your phone. Do not drag and drop the file. This might corrupt it, causing a bootloop upon installiation. (Happened to me initially. Recovered & used the push command to get it to work.). Transfer Magisk Manager's apk to your phone or download it directly from your phone(you can drag and drop this one, as it won't install if corrupted(it won't corrupt)). Install Magisk Manager on the phone(Enable sideloading if asked). In the app, touch the topmost install button and touch install again in the next screen. You will have two options: "Download zip only" and "Select and patch a file". Choose "Select and patch a file", then locate the AP file you transferred to the device. Magisk manager will patch the file and generate magisk_patched.tar in /sdcard/download/. In ADB, type This will transfer it to the platform-tools folder. Again, don't use windows explorer to transfer. That will most certainly corrupt the file.
Step 2.5) Backup
Backup your data (you can use smart switch desktop program paired with mobile app to backup most of the stuff). Remove your google account from the device.
Step 3) Install Nougat 7.1.1
Extract Nougat 7.1.1 firmware. Extract odin. Run Odin.exe (might have version in name). Click OK. Factory reset your phone (You can do so from settings or recovery mode.). After the reset, reboot into download mode. It will ask if you're sure you want to install unofficial software, choose continue (If I don't recall incorrectly, the button for that was vol up). Plug your phone into your PC. Odin log should say "added!!" and you should see your device in one of the rectangles above. Now select the tar.md5 files extracted from the 7.1.1 firmware. Click the BL button, locate the BL_etcetc.tar.md5 file, click open. It will check the md5 for a second then let you click the next button. After choosing the BL(bootloader), AP(system), CP(radio) and CSC(localization) files (USERDATA button should remain empty, HOME_CSC file has no use) make sure only F.reset time and auto reboot are selected in options. Click start to begin. After flashing, it will do another factory reset and show you the setup.
Step 4) Unlock Bootloader
Skip everything in setup, then unlock develper options and you should see "OEM Unlocking" option that was removed in OREO firmware in there. Enable it. Next transfer the CROM service apk to your device (or download it directly). Install the app. Open it. Unlock the bootloader. (This step is required because C9000 is a Chinese phone)
Step 5) Install Oreo again
Boot into download and connect to odin. You can use the reset button to empty the buttons. Now select BL, CP and CSC files from the extracted oreo firmware. For AP, choose magisk_patched.tar . Start. If the installiation fails, you didn't unlock the Bootloader properly. The phone will reboot and factory reset a couple times. When it boots up, you'll have magisk installed.
Step 6) Things to do after rooting(optional)
First of all, magisk can hide root from Google, but not Samsung. Samsung Health, Knox secure container, Maximum power saving mode and Samsung pay won't work after you root. NFC will keep turning on on its own unless you uninstall Samsung pay. A samsung package (I'm not sure about the name but I think it was security log agent) will keep sending an unblockable notification offering to unroot. Uninstall that too, and you'll have a stable experience.
Recovering from fails:
If download mode refuses to install because of unofficial binaries, the bootloader isn't properly unlocked. Wait a couple seconds and force reboot with the key combination. Since it couldn't flash the system, that should reboot back to download mode (or recovery. in that case, choose "reboot to bootloader"). Install the official firmware, unlock bootloader and try again.
If the magisk_patched.tar file gets corruped and you flash the corrupted file successfully, your device will get into a bootloop. After the install, odin orders the phone to reboot into recovery to factory reset, but since the system image is corrupted, it won't be able to boot and produce a kernel panic. This will cause the phone to reboot, which will fail and cause it to try to reboot again. Since the phone doesn't get past the splash screen, this bootloop cannot be interrupted by button shortcuts. You should wait for the battery to die out for the bootloop to end. (It should take a day at max. Wrap a towel around it to block the vibration sounds if you want) After battery gets depleted, you need to perform a quick maneuver. You should plug the phone into a power supply (preferably your computer) while holding down volume down+home+power buttons. If you do it right, it will boot into download mode. (Otherwise, it will bootloop again. Simply unplug, wait for it to stop and try again) Flash the official firmware and repatch the AP file. Just in case you run into this issue, I recommend having less than 10% charge in your phone while flashing, just to make the wait time shorter.
Important: Check your firmware's baseband version from settings before flashing. In C9000ZHU1CSC1, CSC1 is the system and U1 is the bootloader version. Compare the bootloader version to the firmware you're going to flash and make sure they match. You can't downgrade bootloader versions. Flashing a previous version will brick your phone. (Probably permanently) This shouldn't be an issue since sm-C9000 has only one bootloader version, but check it anyways just to be sure.
Click to expand...
Click to collapse
Have you tried this method and phone working fine will there will be any problem if i use this method for rooting c9000?
khankk42 said:
Have you tried this method and phone working fine will there will be any problem if i use this method for rooting c9000?
Click to expand...
Click to collapse
Yes, I did root my SM-C9000 using this method, and it is working nicely. Obviously I lost access to Secure Folder and Samsung Pay. You should be able to install the Play Store version of Samsung Health. Maximum Power Saving froze the phone the first two times I enabled it, but it's working fine now. One unexpected caveat is that mobile hotspot started to turn itself off if mobile data is enabled even though my carrier has no restrictions on using hotspot. You can't share your data connection using Bluetooth or usb cable neither. You can still use the hotspot for creating a local network. Other than those, I didn't experience any problems after rooting. While I was rooting, I did the mistake of using MTP to transfer the image and as a result my phone bootlooped for half a day but if you follow the instructions, that won't be a problem.
Of course, I don't guarantee anything and don't take responsibility, but there is no reason anything should go wrong.
My base band R16NW.C9000ZHU1CSC1, model number SM-C9000, android 8.0.0...
I have never rooted any phones in my life. What should i do? I search on internet but i didnt found any spesific things about "R16NW.C9000ZHU1CSC1" can you help me? Those options will work for me to ?
otocu said:
My base band R16NW.C9000ZHU1CSC1, model number SM-C9000, android 8.0.0...
I have never rooted any phones in my life. What should i do? I search on internet but i didnt found any spesific things about "R16NW.C9000ZHU1CSC1" can you help me? Those options will work for me to ?
Click to expand...
Click to collapse
Sorry for responding late. Yes, that is the exact model that I have and rooted using the method in the post. If you feel confident, you can follow trough it and root your phone. You can grab the required firmware from Sammobile. Keep in mind that after rooting some features might stop working (like hotspot and knox-related features). Good luck!
I got the same model of Samsung phone. I follow the steps but till step five, when i press open the files in odin and press start button, the odin will disappear in my computer. Then i try again and it failed. My phone shows: unsuppoted dev types. Here are my photos. Do you have any ideas? And i dunno how can i redo it again to root my phone. Would love to see helps from you, thanks!
cherrio128 said:
I got the same model of Samsung phone. I follow the steps but till step five, when i press open the files in odin and press start button, the odin will disappear in my computer. Then i try again and it failed. My phone shows: unsuppoted dev types. Here are my photos. Do you have any ideas? And i dunno how can i redo it again to root my phone. Would love to see helps from you, thanks!
Click to expand...
Click to collapse
Sorry for the late response. Searching that on the internet, it seems you might be using an old version of Odin. Please make sure you're using 3.13.1 and try again
Code:
Your warranty is now void.
If you root your device, Your KNOX status will be tripped.
You can still pass the safety net after you root if you follow the instructions.
I am not responsible for bricked devices, dead SD cards although it is not really possible
Please do some research if you have any concerns about doing this to your device
How to flash official firmware? (not the root and unlock bootloader part!)
You will need:
A Galaxy A22 5G and common sense
Samsung Odin (the flashing tool of the official firmware)
https://dl2018.sammobile.com/Odin3-v3.14.1.zip
You need to extract the zip file and you are going to use the file Odin3_v3.14.1.exe inside the folder.
Samsung Android USB Driver for Windows
Samsung Android USB Driver | Samsung Developers
You need the driver only if you are developing on Windows and want to connect a Samsung Android device to your development environment over USB.
developer.samsung.com
Double-click and install the exe file.
Samsung Official Firmware
Release 1.0.3 · zacharee/SamloaderKotlin
Contribute to zacharee/SamloaderKotlin development by creating an account on GitHub.
github.com
Download the platform you want to download to. (Windows)
You need to extract the zip and double click open the file Bifrost.exe inside the folder.
You need to fill in the Model, Region, press the Check for Updates button and the Download button.
How to find the Model: on your phone → Settings → About Phone → The third row says the Model number and you need to remove the part with the part of /xx, for example, SM-A226B/DS and you only need to type SM-A226B
How to find the Region: You can check the Region at this link https://samfrew.com/model/SM-S908B/
You need to find find a three-letter word depending on your carrier and country and type it in Bifrost, for example, EVR
Press the Check for Update button and download it with the Download button.
Put it to a place you can easily find, ie. Desktop.
After downloading it, find the file SM-xxxxx_x_xxxxxxxx_xxx.zip.enc4 on the place you put it and change the document format from .enc4 to .zip. Then, double click and extract the file.
Open Odin3_v3.14.1.exe and turn off your phone. Connect a side of your USB to your PC/Laptop, keep pressing volume up and down together until you go to Download Mode. Put another side of the USB into your phone. When you arrived at Download Mode press volume up. Go back to Odin3_v3.14.1.exe:
-Click on BL and select BL_xxxxxxxxxx.tar.md5
-Click on AP and select AP_xxxxxxxxxxx.tar.md5
-Click on CP and select CP_xxxxxxxxxx.tar.md5
(If you want to keep your data don't flash CSC).
-Click on CSC and select CSC_OMC_xxxxxxxxxx.tar.md5
-Click on USERDATA and select HOME_CSC_OMC_xxxxxxxxxx.tar.md5
Press Start to flash the firmware, after done, your device will automatically reboot to the system.
How to unlock the bootloader?
Go to your phone → Settings → About Phone → Software information → Press Build number 6 times until you see the notice “You’re now a developer”
Go in Settings → Developer options → enable OEM unlocking
Power off your phone first. Then, connect a side of your USB to your PC/Laptop, keep pressing volume up and down together until you go to Download Mode. Put another side of the USB into your phone.
When you arrived at Download Mode, long press volume up until you see the black screen. Confirm to unlock the bootloader and you will erase your device.
How to root your phone?
After you unlock your bootloader, you set up your phone and make sure you do not sign in google account first. Install Magisk https://github.com/topjohnwu/Magisk/releases/download/v24.1/Magisk-v24.1.apk on your phone. Oh yes, in case you do not know, you need to allow the app to install apps so that you can install the apk.
Transfer AP_xxxxxxxxxx.tar.md5 in the firmware you download from your PC/Laptop to your phone.
Open Magisk on your phone and press the install button in the Magisk column. Select 'Select and Patch a File', 'Let's Go' and find the AP_xxxxxxxxxx.tar.md5 and select it. You can have a cup of coffee if you like when you waiting for the patching of the file.
After finishing the patching, you need to transfer the file magisk_patched-24xxx_xxxxx.tar in the Downloads folder back to your PC/Laptop.
Turn off your phone. Connect a side of your USB to your PC/Laptop, keep pressing volume up and down together until you go to Download Mode. Put another side of the USB into your phone. When you arrived at Download Mode press volume up. Open Odin3_v3.14.1.exe on your PC/Laptop:
Click on BL and select BL_xxxxxxxxxx.tar.md5
-Click on AP and select magisk_patched-24xxx_xxxxx.tar
-Click on CP and select CP_xxxxxxxxxx.tar.md5
(If you want to keep your data don't flash CSC).
-Click on CSC and select CSC_OMC_xxxxxxxxxx.tar.md5
-Click on USERDATA and select HOME_CSC_OMC_xxxxxxxxxx.tar.md5
When it finishes flashing it, it will automatically reboot and you can gain root access.
Optional: If you want to have the safety net passed (most of the banking apps use it), then you need to install the zip
as a Magisk module in Magisk https://github.com/kdrag0n/safetynet-fix/releases
How? Go to Magisk → Modules → install from storage and select the zip you downloaded.
Or you could just get your AP file and extract your boot.img.lz4 (use lz4 from github), put it on your phone and patch it with Magisk, then flash the VBMeta that this thread has in Odin, reboot and erase the cache and data in the stock recovery, rebooting to download mode again and flashing your magisk patched boot img in a tar file.
Platypus Enthusiast said:
Or you could just get your AP file and extract your boot.img.lz4 (use lz4 from github), put it on your phone and patch it with Magisk, then flash the VBMeta that this thread has in Odin, reboot and erase the cache and data in the stock recovery, rebooting to download mode again and flashing your magisk patched boot img in a tar file.
Click to expand...
Click to collapse
I agree with you. You can also use this way. However, using Magisk does all the jobs makes life easier and I am a bit lazy
Hi! I'm new into rooting and I just wanted to know, What's the risk of bricking when using magisk? I've rooted an old phone successfully via TWRP tho this way seems a bit more direct, and can I choose any region during the official firmware download?
MateoElias said:
Hi! I'm new into rooting and I just wanted to know, What's the risk of bricking when using magisk? I've rooted an old phone successfully via TWRP tho this way seems a bit more direct, and can I choose any region during the official firmware download?
Click to expand...
Click to collapse
The worst that would happen is a bootloop, which you can easily fix with a factory reset (not a good solution, but at least it works). The only dangerous part is installing the wrong TWRP version or a failed Odin flash, but no bricks. Odin mode will almost always work. Just make sure you have a charger in good condition.
As for picking regions, I'd just pick the phone's original region, if I were you. I'm not actually sure if region is tied to the device itself but better safe than sorry.
Greetings...
To check your Buld Number or Build Version, before you proceed doing any stuffs, type on the phone keypad this >>> *#1234#* and it will show on your device screen
Just tried to follow the guide, but I'm getting an error while flashing:
Custom binary blocked by OEM Lock: vbmeta
Firmware used:
A226BXXU4AVB1_A226BOXM4AVB1_NEE
Patched AP with Magisk 24.3.
Edit: NVM, LONG press volume up...
tried to follow the guide my A22 is rooted. But i have problem.
no application recognizes the root. I installed root checker and he says my phone is rooted but superuser binary files it not installed
Any one can help please?
Alpa475 said:
tried to follow the guide my A22 is rooted. But i have problem.
no application recognizes the root. I installed root checker and he says my phone is rooted but superuser binary files it not installed
Any one can help please?
Click to expand...
Click to collapse
I suppose you may have installed to sbin, but I am not really sure
Can you update the link to the Magisk release?
Leonardo Green said:
You can root Galaxy A22 and A22 5G in TWRP.
Click to expand...
Click to collapse
I am not familiar with the A22 series, but I will say this: I'm rather wary of questionable root solutions, especially those that aren't open source. This is why I personally prefer Magisk - it is completely open source, so anyone who would like to examine the code can do so.
Sorry, when i See this tutorial, my phone has updated to android 13. Could this step possible to do now with this android version?
Very much thank you for the information!
have successfully run the tutorial above. even already using GSI rom android 13 from pixelExperience. but the network you get is stuck on 4G. are there any tools or tutorials to restore the 5g network.
Williamtung said:
Code:
Your warranty is now void.
If you root your device, Your KNOX status will be tripped.
You can still pass the safety net after you root if you follow the instructions.
I am not responsible for bricked devices, dead SD cards although it is not really possible
Please do some research if you have any concerns about doing this to your device
How to flash official firmware? (not the root and unlock bootloader part!)
You will need:
A Galaxy A22 5G and common sense
Samsung Odin (the flashing tool of the official firmware)
https://dl2018.sammobile.com/Odin3-v3.14.1.zip
You need to extract the zip file and you are going to use the file Odin3_v3.14.1.exe inside the folder.
Samsung Android USB Driver for Windows
Samsung Android USB Driver | Samsung Developers
You need the driver only if you are developing on Windows and want to connect a Samsung Android device to your development environment over USB.
developer.samsung.com
Double-click and install the exe file.
Samsung Official Firmware
Release 1.0.3 · zacharee/SamloaderKotlin
Contribute to zacharee/SamloaderKotlin development by creating an account on GitHub.
github.com
Download the platform you want to download to. (Windows)
You need to extract the zip and double click open the file Bifrost.exe inside the folder.
You need to fill in the Model, Region, press the Check for Updates button and the Download button.
How to find the Model: on your phone → Settings → About Phone → The third row says the Model number and you need to remove the part with the part of /xx, for example, SM-A226B/DS and you only need to type SM-A226B
How to find the Region: You can check the Region at this link https://samfrew.com/model/SM-S908B/
You need to find find a three-letter word depending on your carrier and country and type it in Bifrost, for example, EVR
Press the Check for Update button and download it with the Download button.
Put it to a place you can easily find, ie. Desktop.
After downloading it, find the file SM-xxxxx_x_xxxxxxxx_xxx.zip.enc4 on the place you put it and change the document format from .enc4 to .zip. Then, double click and extract the file.
Open Odin3_v3.14.1.exe and turn off your phone. Connect a side of your USB to your PC/Laptop, keep pressing volume up and down together until you go to Download Mode. Put another side of the USB into your phone. When you arrived at Download Mode press volume up. Go back to Odin3_v3.14.1.exe:
-Click on BL and select BL_xxxxxxxxxx.tar.md5
-Click on AP and select AP_xxxxxxxxxxx.tar.md5
-Click on CP and select CP_xxxxxxxxxx.tar.md5
(If you want to keep your data don't flash CSC).
-Click on CSC and select CSC_OMC_xxxxxxxxxx.tar.md5
-Click on USERDATA and select HOME_CSC_OMC_xxxxxxxxxx.tar.md5
Press Start to flash the firmware, after done, your device will automatically reboot to the system.
How to unlock the bootloader?
Go to your phone → Settings → About Phone → Software information → Press Build number 6 times until you see the notice “You’re now a developer”
Go in Settings → Developer options → enable OEM unlocking
Power off your phone first. Then, connect a side of your USB to your PC/Laptop, keep pressing volume up and down together until you go to Download Mode. Put another side of the USB into your phone.
When you arrived at Download Mode, long press volume up until you see the black screen. Confirm to unlock the bootloader and you will erase your device.
How to root your phone?
After you unlock your bootloader, you set up your phone and make sure you do not sign in google account first. Install Magisk https://github.com/topjohnwu/Magisk/releases/download/v24.1/Magisk-v24.1.apk on your phone. Oh yes, in case you do not know, you need to allow the app to install apps so that you can install the apk.
Transfer AP_xxxxxxxxxx.tar.md5 in the firmware you download from your PC/Laptop to your phone.
Open Magisk on your phone and press the install button in the Magisk column. Select 'Select and Patch a File', 'Let's Go' and find the AP_xxxxxxxxxx.tar.md5 and select it. You can have a cup of coffee if you like when you waiting for the patching of the file.
After finishing the patching, you need to transfer the file magisk_patched-24xxx_xxxxx.tar in the Downloads folder back to your PC/Laptop.
Turn off your phone. Connect a side of your USB to your PC/Laptop, keep pressing volume up and down together until you go to Download Mode. Put another side of the USB into your phone. When you arrived at Download Mode press volume up. Open Odin3_v3.14.1.exe on your PC/Laptop:
Click on BL and select BL_xxxxxxxxxx.tar.md5
-Click on AP and select magisk_patched-24xxx_xxxxx.tar
-Click on CP and select CP_xxxxxxxxxx.tar.md5
(If you want to keep your data don't flash CSC).
-Click on CSC and select CSC_OMC_xxxxxxxxxx.tar.md5
-Click on USERDATA and select HOME_CSC_OMC_xxxxxxxxxx.tar.md5
When it finishes flashing it, it will automatically reboot and you can gain root access.
Optional: If you want to have the safety net passed (most of the banking apps use it), then you need to install the zip
as a Magisk module in Magisk https://github.com/kdrag0n/safetynet-fix/releases
How? Go to Magisk → Modules → install from storage and select the zip you downloaded.
Click to expand...
Click to collapse
Hi, Thanks for sharing this but unfortunately my camera is not working after doing all this. Please suggest what should i do
Praveenbha said:
Hi, Thanks for sharing this but unfortunately my camera is not working after doing all this. Please suggest what should i do
Click to expand...
Click to collapse
Have you tried Universal Safetynet fix? https://github.com/kdrag0n/safetynet-fix
I rooted the phone according to your guide
But after everything I can't connect to the internet
Youtube, system update doesn't work
MAGISK itself was able to update without any problem
Chrome will turn on pages, but without images and displays error about unsecured connection