Well I finally managed to Hard Brick my A110 a few days back. I was thinking that everything was lost and my A110 was as good as a brick! But I struggled with it for two days and finally managed to bring it back to life! This is how I hard bricked it, but resurrected it too....
Hard brick:
The hard brick happens when you flash a non A110 stock ROM through SP flash. This happens when you get overconfident during ROM development experiments and forget the basic fact that flashing the "pre-loader" accidentally of any other ROM( (even if it is of MT6577) that is different from A110 leads to the phone going dead. The charge LED dies, and the phone is totally in alien land when the PC sees it through the USB cable You cannot flash anything through the SP flash any more. The phone will not power on or boot. Welcome to the land of bricked phones!
Resurrection:
1) First perform an uninstall of the MMX/Mobistel drivers you already have on
your P.C. Install the drivers again.
2) Take a piece of insulated wire (Around 3 cms long) and solder a 10K resistor
to one end. To the other end solder a pin to the pin head so that the tip is
free.
3) Remove your phone battery and keep the phone ready.
4) On the PC/Laptop, start SP flash tool and select the right scatter from the factory stock A110 ROM. un-tick all except the first five (Preloader, DSP_BL, MBR, EBR1, UBOOT) + CWM recovery (You should have replaced default recovery with CWM recovery in the ROM folder). Click "Firmware-upgrade, Download.
5) With battery taken off from your phone connect it to the PC/Lap using the USB cable.
6) Now touch the resistor end to the USB Cable outer part (GND) visible at the point of USB connector connected to the phone.
7) Touch the other part (pin end) to all visible copper terminals one by one.
8) Now without removing the cable, place the battery back.
9) Now keep your fingers crossed. If you have luck, you will see the red, blue, green and finally yellow lines on the SP tool window. You are done!!!
10) If your battery was having good charge when you were bricked, you can now power on to recovery mode and flash your CWM saved ROM or any other ROM.
11) If your battery was low, when you were bricked, leave it to charge for an hour before attempting to flash the entire stock ROM through SP flash or CWM.
Cheers!!!:victory:
Its better u make a video and attached it below. its really helpful. thanxx a lot mate for creating this solution :thumbsup:
i second that suggestion! a video or an orderly series of pics........
skdmech94 said:
Its better u make a video and attach.........
Click to expand...
Click to collapse
wow maan u really are awesome i never had myself in d scenario but now i know that theres always a way thanks to you hats off to u pal
Yap bro u r right....u have to post a video guide......
colors can.....canvas 2
At least a series of pictures are most for such guide.
Great tutorial (please make video or screens)
Will help so many a110 users
Whose devices are in verge of death
From horrible MMX service center guys
Sent from my Micromax A110 using xda premium
Great article!! Video would be extremely helpful!
Sent from my GT-I9300 using xda app-developers app
Hard brick occurs when we flash preloader of different incompatible fone ryt...and hence fone wont detect on spflash tool..
What if we install the preloader drivers of that incompatible device; can we get the fone to detect in spflashtools ? If it wrks, then we can flash back the A110 preloader files ryt ?
Some one with a hardbricked device ,pls try it out if possible, before doing the hardware method suggested by OP
Sent from my Micromax A110
pcoruganti said:
Great article!! Video would be extremely helpful!
Sent from my GT-I9300 using xda app-developers app
Click to expand...
Click to collapse
Will post some snaps
Hi,
Thanks for this wonderful tutorial, Now i am not worried about my phone being bricked when i try new things in my mobile. thanks buddy.
where i can get CWM recovery?
Where i can get that CWM recovery?
I followed all these steps i couldnt do anymore, what i should i do next? Plz help
I followed all these steps i couldnt do anymore, what i should i do next? Plz help
pradipsoman said:
Well I finally managed to Hard Brick my A110 a few days back. I was thinking that everything was lost and my A110 was as good as a brick! But I struggled with it for two days and finally managed to bring it back to life! This is how I hard bricked it, but resurrected it too....
Hard brick:
The hard brick happens when you flash a non A110 stock ROM through SP flash. This happens when you get overconfident during ROM development experiments and forget the basic fact that flashing the "pre-loader" accidentally of any other ROM( (even if it is of MT6577) that is different from A110 leads to the phone going dead. The charge LED dies, and the phone is totally in alien land when the PC sees it through the USB cable You cannot flash anything through the SP flash any more. The phone will not power on or boot. Welcome to the land of bricked phones!
Resurrection:
1) First perform an uninstall of the MMX/Mobistel drivers you already have on
your P.C. Install the drivers again.
2) Take a piece of insulated wire (Around 3 cms long) and solder a 10K resistor
to one end. To the other end solder a pin to the pin head so that the tip is
free.
3) Remove your phone battery and keep the phone ready.
4) On the PC/Laptop, start SP flash tool and select the right scatter from the factory stock A110 ROM. un-tick all except the first five (Preloader, DSP_BL, MBR, EBR1, UBOOT) + CWM recovery (You should have replaced default recovery with CWM recovery in the ROM folder). Click "Firmware-upgrade, Download.
5) With battery taken off from your phone connect it to the PC/Lap using the USB cable.
6) Now touch the resistor end to the USB Cable outer part (GND) visible at the point of USB connector connected to the phone.
7) Touch the other part (pin end) to all visible copper terminals one by one.
8) Now without removing the cable, place the battery back.
9) Now keep your fingers crossed. If you have luck, you will see the red, blue, green and finally yellow lines on the SP tool window. You are done!!!
10) If your battery was having good charge when you were bricked, you can now power on to recovery mode and flash your CWM saved ROM or any other ROM.
11) If your battery was low, when you were bricked, leave it to charge for an hour before attempting to flash the entire stock ROM through SP flash or CWM.
Cheers!!!:victory:
Click to expand...
Click to collapse
pradipsoman said:
Well I finally managed to Hard Brick my A110 a few days back. I was thinking that everything was lost and my A110 was as good as a brick! But I struggled with it for two days and finally managed to bring it back to life! This is how I hard bricked it, but resurrected it too....
Hard brick:
The hard brick happens when you flash a non A110 stock ROM through SP flash. This happens when you get overconfident during ROM development experiments and forget the basic fact that flashing the "pre-loader" accidentally of any other ROM( (even if it is of MT6577) that is different from A110 leads to the phone going dead. The charge LED dies, and the phone is totally in alien land when the PC sees it through the USB cable You cannot flash anything through the SP flash any more. The phone will not power on or boot. Welcome to the land of bricked phones!
Resurrection:
1) First perform an uninstall of the MMX/Mobistel drivers you already have on
your P.C. Install the drivers again.
2) Take a piece of insulated wire (Around 3 cms long) and solder a 10K resistor
to one end. To the other end solder a pin to the pin head so that the tip is
free.
3) Remove your phone battery and keep the phone ready.
4) On the PC/Laptop, start SP flash tool and select the right scatter from the factory stock A110 ROM. un-tick all except the first five (Preloader, DSP_BL, MBR, EBR1, UBOOT) + CWM recovery (You should have replaced default recovery with CWM recovery in the ROM folder). Click "Firmware-upgrade, Download.
5) With battery taken off from your phone connect it to the PC/Lap using the USB cable.
6) Now touch the resistor end to the USB Cable outer part (GND) visible at the point of USB connector connected to the phone.
7) Touch the other part (pin end) to all visible copper terminals one by one.
8) Now without removing the cable, place the battery back.
9) Now keep your fingers crossed. If you have luck, you will see the red, blue, green and finally yellow lines on the SP tool window. You are done!!!
10) If your battery was having good charge when you were bricked, you can now power on to recovery mode and flash your CWM saved ROM or any other ROM.
11) If your battery was low, when you were bricked, leave it to charge for an hour before attempting to flash the entire stock ROM through SP flash or CWM.
Cheers!!!:victory:
Click to expand...
Click to collapse
if you will make video...then u r awesome awesome awesome
Sent from my Demon A110 using xda app-developers app
drsooraj said:
Hard brick occurs when we flash preloader of different incompatible fone ryt...and hence fone wont detect on spflash tool..
What if we install the preloader drivers of that incompatible device; can we get the fone to detect in spflashtools ? If it wrks, then we can flash back the A110 preloader files ryt ?
Some one with a hardbricked device ,pls try it out if possible, before doing the hardware method suggested by OP
Sent from my Micromax A110
Click to expand...
Click to collapse
What an idea.
The only problem is who's gonna hard brick his phone for this experiment.
Matthew_Farrell said:
What an idea.
The only problem is who's gonna hard brick his phone for this experiment.
Click to expand...
Click to collapse
yea ...thats why i am asking it to the next guy who gets a hardbrick and is just about to follow pradip sir's steps following this thread, to just give a try , before doing it the hardwire method!
Resister method works for almost every phone
It will put the phone in download mode
Even it is not booting or charging
guide can be found on xda
Just search it
Jigs methods works as well
Sent from my Micromax A110 using xda premium
In Step 7 which "visible copper terminals" are meant?
The Phone is connected to PC and the other end of data cable is pluged into phone, so there are no copper pins to touch.
is it possible to do same on mmx a87... m8ne is also hard bricked....
Phoenix said:
Resister method works for almost every phone
It will put the phone in download mode
Even it is not booting or charging
guide can be found on xda
Just search it
Jigs methods works as well
Sent from my Micromax A110 using xda premium
Click to expand...
Click to collapse
after getting into the download mode how can I flash a rom in mmx a87.. plz help.. my fone hard bricked...
Related
Hi Experts,
I was successfully able to flash ICS on my LG O3D but only .bin file and after that i tried to root phone was not sucessfully all the time ,restarted later and now my phone is not switching on properly.It shows LG logo then goes blank. PLEASE HELP.
Thanks in Advance.
When connected its showing charging and in device manager-->other devices showing CDC Serial & LGE COSMO USB Device
Did you try reflash it again ???
Try flash it with "lg smartflash" it tooo easy (just select the .bin file and .fls) .
Good Luck
Sent from my LG-P920
OS_Hacking said:
Did you try reflash it again ???
Try flash it with "lg smartflash" it tooo easy (just select the .bin file and .fls) .
Good Luck
Sent from my LG-P920
Click to expand...
Click to collapse
Thanks a lot for the reply.
I tried but nothing happening..its not detecting as usb to change port to 41.
Is there any other way?? Also for flashing when i insert battery and press volume up and then connect it starts and shows LG logo and goes blank.
It is not showing in PORT in device manager when connected pressing volume + button
Does the phone go to download mode ("S/W upgrade mode ) ?? By insert the battery while you hold vol+ ??
You will see two arrows like the sync symbol in your phone screen . And then the phone will still connected with the PC .
Your problem is easy to fix . Just try to enter download mode . And every thing will be fine .
Good Luck
Sent from my LG-P920
No its not going into download mode. COM is not detecting it.
[email protected] said:
No its not going into download mode. COM is not detecting it.
Click to expand...
Click to collapse
Try hold power on and the vol+ together , then plug it with the PC . Then insert the battery .
Sent from my LG-P920
[email protected] said:
Hi Experts,
I was successfully able to flash ICS on my LG O3D but only .bin file and after that i tried to root phone was not sucessfully all the time ,restarted later and now my phone is not switching on properly.It shows LG logo then goes blank. PLEASE HELP.
Thanks in Advance.
Click to expand...
Click to collapse
You hardbricked your phone if it doesn't go into download mode.
But no panic there is always a solution;
http://forum.xda-developers.com/showthread.php?t=1942836
Follow the guide above. (and I mean every step , however small they may seem)
ICS roms are now pre-rooted so you don't have to root.
Flash Xbsall's Ported custom ics (The one in the guide.)
Then install wkpark's recovery img. (Found here ; http://forum.xda-developers.com/showthread.php?t=1978543)
Boot into recovery.
Install Darkroom ICS Int. (It's the best in my opinion) or whatever rom you wish.
They are all pre-rooted.
If you can't i'll guide you through it.
Hope i Helped.
Cheers!
boltthrower56 said:
You hardbricked your phone if it doesn't go into download mode.
But no panic there is always a solution;
http://forum.xda-developers.com/showthread.php?t=1942836
Follow the guide above. (and I mean every step , however small they may seem)
ICS roms are now pre-rooted so you don't have to root.
Flash Xbsall's Ported custom ics (The one in the guide.)
Then install wkpark's recovery img. (Found here ; http://forum.xda-developers.com/showthread.php?t=1978543)
Boot into recovery.
Install Darkroom ICS Int. (It's the best in my opinion) or whatever rom you wish.
They are all pre-rooted.
If you can't i'll guide you through it.
Hope i Helped.
Cheers!
Click to expand...
Click to collapse
Thanks a lot for the help and i really appreciate your willingness to take me out of this trouble, Thanks again
Everything worked fine till step 9..But still not showing anything in Ports
Make sure the drivers are correctly installed. Especially omap4430...
Start the script that has been referred to in the guide.
Shut down the phone , remove the battery , plug usb cable and when you see "waiting for 5 seconds" plug in the battery. That should work.
Keep me posted.
Sent from my LG-P920 using xda app-developers app
Its showing s/w update image in phone but getting message USB device not detected in PC
Thanks alot boltthrower56 .
Finally able to recover my phone and restored 3 month old backup.
By the way may i know your real name .
Can you please help me with upgrading to ICS?
[email protected] said:
Its showing s/w update image in phone but getting message USB device not detected in PC
Click to expand...
Click to collapse
That may mean you have a bad cable.
But if you restored it , it's probably sometimes bad or you changed it or you used the front panel which is a hub (divides bandwidth , slows flashing process) and it's bad for ya.
Since my real name is turkish and hard to spell i'll give one better ;
Call me John.
If you must know my real name is "Dogukan".
And yes i can help you with that although it's relatively easy now that you got a hold of it.
Thanks a lot Dogukan..
Are you into android development? Am a real noob in this and you helped me coming out of really difficult situation.
Now i want to root my phone and everytime its showing 'error no device find'
I'm not into android development... my skills lie in networking so there is not much i can do for android.
But those are common knowledge...
I bricked my phone several times to learn those.
You don't need to root. Follow wkpark's recovery installation and flash a custom rom (Darkroom int is great)
Sent from my LG-P920 using xda app-developers app
please please help to unbrick my Xolo a500
is a hard brick, can not turn on. does not work with the charger or anything
this happened to have installed swapper 2 and reboot. never returned to light or anything.
attempt to Android_AIO_Flasher_1.40 and not recognized even having installed adb drivers
Well,this happened to other people too, if you read the comments.
I guess you either need to somehow hard reset it or something.
hi.same happened here....tried to install custom roms,roms are installed but the phone is not starting...stucked at XOLO logo and after some time it shuts down...tried to flash stock rom also..but the same thing is happening .....
please help me if u know the solution...
daviyankee said:
please please help to unbrick my Xolo a500
is a hard brick, can not turn on. does not work with the charger or anything
this happened to have installed swapper 2 and reboot. never returned to light or anything.
attempt to Android_AIO_Flasher_1.40 and not recognized even having installed adb drivers
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?p=46548211#post46548211
try using SP flash tool and download roms for the dash
USB Jig
daviyankee said:
please please help to unbrick my Xolo a500
is a hard brick, can not turn on. does not work with the charger or anything
this happened to have installed swapper 2 and reboot. never returned to light or anything.
attempt to Android_AIO_Flasher_1.40 and not recognized even having installed adb drivers
Click to expand...
Click to collapse
Hi, to unbrick a device, you can use in general a USB Jig. It is a litile USB you plug in to your device and it gets unbricked in 5s. This looks a little magical but it works. In fact, most companies protect their devices from hard-brick by putting a second, non software reachable memory whith a copy of its bootloader. Inserting a USB with a 300kOhm (called USB Jig) resistance makes it restore the bootloader, and then it become unbricked and you can load a new ROM to your device.
Here are some videos on how to make a USB Jig, and how to use it. (you just have to plug it in reality)
Well, just search "USB jig" on youtube and you'll find tons of good results, especially the three first ones.
PS: you may either create your own USB jig or buy one from a store or the internet.
Xolo q500 softbricked
Can Anyone Help me. My Xolo Q500 is softbricked. It is niether booting normally nor booting to recovery menu. I have tried sp flash tools but the stock rom of my phone which i downloaded does not contain any scatter file, probably because it is a Qualcomm based device. Please help me..................
xolo q500 dead after formated
xolo q500 dead after formated
sir please help me i do have the same problem
xolo q 500 i soft bricked using format while connect in the smart upgared tool
i tried to flash but its ask disk to be formatted i am unaware of it so i mistakenly formatted now the phone is not getting turn on
or in the recovery mode please help or tell me the procedure
an Anyone Help me. My Xolo Q500 is softbricked. It is niether booting normally nor booting to recovery menu.
I have a Micromax A100 mobile which is out of warranty. I tried to update the ICS with Jb 4.1.1 and at that time the mobile got OFF and now I am not able to SWITCH ON the mobile .
I tried with VolDown + Power key at the same time to launch FASTBOOT and so many options like that. The mobile is not ON.
Actually at the time of installation of GRAND ROM V3, downloaded from this site, it got struck, showing the message ""ERROR 7, Installtion Aborted"". I manually operated the options ( dont exactly remember) and tried to REBOOT and then it got OFF and not SWITCHED ON till now for the past 10 days.
When I connect it to PC with USB Cable, it is NOT SHOWN as a device in MY COMPUTER but is showing in Device Manager as "Qualcomm HS-USB QDLoader 9008" . What does this mean and what to do to solve this issue.
If you people say it is BRICKED, what is the solution for this ?
How can I get back my phone back in ON condition ?
Thanking you in anticipation for a solution.
Murthy
vsrkmurthy said:
I have a Micromax A100 mobile which is out of warranty. I tried to update the ICS with Jb 4.1.1 and at that time the mobile got OFF and now I am not able to SWITCH ON the mobile .
I tried with VolDown + Power key at the same time to launch FASTBOOT and so many options like that. The mobile is not ON.
Actually at the time of installation of GRAND ROM V3, downloaded from this site, it got struck, showing the message ""ERROR 7, Installtion Aborted"". I manually operated the options ( dont exactly remember) and tried to REBOOT and then it got OFF and not SWITCHED ON till now for the past 10 days.
When I connect it to PC with USB Cable, it is NOT SHOWN as a device in MY COMPUTER but is showing in Device Manager as "Qualcomm HS-USB QDLoader 9008" . What does this mean and what to do to solve this issue.
If you people say it is BRICKED, what is the solution for this ?
How can I get back my phone back in ON condition ?
Thanking you in anticipation for a solution.
Murthy
Click to expand...
Click to collapse
Actually Ur fone is a110 or a100 .If u r having a100 and flashed grand v3 rom which is for a110 u have hard bricked the fone .Can u enter into the recovery mode ?? Do u have a NANDROID back up ?
You flashed a110 rom on a100? Well then, yes it's partially bricked, since your bootloader is working as per device manager , so you can try to flash stock rom ofA100 on it using a flash tool meant for it.
Sent from my potato chamber using xda app-developers app
mufti.arfan said:
You flashed a110 rom on a100? Well then, yes it's partially bricked, since your bootloader is working as per device manager , so you can try to flash stock rom ofA100 on it using a flash tool meant for it.
Sent from my potato chamber using xda app-developers app
Click to expand...
Click to collapse
Well it may be Hard bricked not Partially bricked As you told the bootloader wont work as per device layout u cant boot the phone :good:
vish97 said:
Well it may be Hard bricked not Partially bricked As you told the bootloader wont work as per device layout u cant boot the phone :good:
Click to expand...
Click to collapse
But it's being detected by his pc. He can try doing some work around to flash stock. But chances are very least.
Sent from my potato chamber using xda app-developers app
Micromax A100 Switch ON Problem.
Friends,
Many of you told many options. My issue is unless it is detected by the PC (as a device under my computer), we will not be able to do anything as per me.
The other day I tried to do something using QPST V.2.7.402 and there also, the phone was detected as per the COM2 but capturing is not done and hence there also I was not able to do .
Understood from our forum only about UNBRICK. What does it mean and will there be any use of having it ? Also downloaded EAZY JTAG today morning using the links from our forum. Is it at all useful for me ?
To let all you guys know, the phone has no problem at all prior to this ROM installation. Now, am not able to SWITCH it ON.
As asked by Mr VISH97, I don't have any backup or I am not able to switch on the phone, so where is the point of entering recovery mode ?
As you guys say BRICKED is there any other solution for get back to working ??
vsrkmurthy said:
Friends,
Many of you told many options. My issue is unless it is detected by the PC (as a device under my computer), we will not be able to do anything as per me.
The other day I tried to do something using QPST V.2.7.402 and there also, the phone was detected as per the COM2 but capturing is not done and hence there also I was not able to do .
Understood from our forum only about UNBRICK. What does it mean and will there be any use of having it ? Also downloaded EAZY JTAG today morning using the links from our forum. Is it at all useful for me ?
To let all you guys know, the phone has no problem at all prior to this ROM installation. Now, am not able to SWITCH it ON.
As asked by Mr VISH97, I don't have any backup or I am not able to switch on the phone, so where is the point of entering recovery mode ?
As you guys say BRICKED is there any other solution for get back to working ??
Click to expand...
Click to collapse
If the board is bricked, nothing can be done, other than jtag method. Which necessarily doesn't work every time.
Sent from my potato chamber using xda app-developers app
Hello guys..
Karbonn A12+ is newly launched Android phone with 1.3GHz processor and 512MB RAM...Still we didn't have Stock ROM for this model...
Now i proudly present Stock jellybean ROM for Karbonn A12+..
I prepared it to flash via SP Flash Tool..
Now don't worry to experiment with your Mobile do experiment and you can recover your karbonn A12+...
So keep learning and Do some intresting experiment and make some custom ROM...
NOTE:- Flashing Process and these type of development process may cause any unwanted and unknown errors...So please Try it at your OWN RISK...I will not Responsible for any damge...
now here are is method to flash.
(Try At Your OWN RISK...)
you Need.
1.An PC (Ofcorse you need and PC or laptop)
2. Karbonn A12+ Stock jellybean ROM (Download)
3. SP_Flash_Tool v3.1312.0.139 (other Version may not work proper)(NOTE:- Flashing Process and these type of development process may cause any unwanted and unknown errors...So please Try it at your OWN RISK...I will not Responsible for any damge...[/COLOR][/B]
Download Links:-
[url]http://a2zandroidrom.blogspot.in/2014/09/karbonn-a12-stock-jellybean-rom.html
Drivers are added...
links are
http://a2zandroidrom.blogspot.in/2014/09/karbonn-a12-stock-jellybean-rom.html
Download file is password protected..password is given in download link page...Download is available in small parts as well as in single part also...
post your review please !!
Good work Bro . . .
suthar88.sunil said:
Good work Bro . . .
Click to expand...
Click to collapse
Thanks
Phone not connecting
greatpapa said:
Hello guys..
Karbonn A12+ is newly launched Android phone with 1.3GHz processor and 512MB RAM...Still we didn't have Stock ROM for this model...
Now i proudly present Stock jellybean ROM for Karbonn A12+..
I prepared it to flash via SP Flash Tool..
Now don't worry to experiment with your Mobile do experiment and you can recover your karbonn A12+...
So keep learning and Do some intresting experiment and make some custom ROM...
NOTE:- Flashing Process and these type of development process may cause any unwanted and unknown errors...So please Try it at your OWN RISK...I will not Responsible for any damge...
now here are is method to flash.
(Try At Your OWN RISK...)
you Need.
1.An PC (Ofcorse you need and PC or laptop)
2. Karbonn A12+ Stock jellybean ROM
3. SP_Flash_Tool v3.1312.0.139 (other Version may not work proper)
Method
1. Download all files on your PC and extract them on one place.
2. now you will have two folder name by "!Files_to_FlashTool" and "SP_Flash_Tool_v3.1312.0.139"
3. Now RUN SP flash Tool.
4. now click on "scatter-loading" tab.
5. now Select "scatter file"....Sp tool will list up all the component to flash.
6.now hit the Download button on SP...you will see an warning something like user data and cache are not loaded or something...just ignore it...and click on "Yes".and now you are ready to flash.
7. Now switchoff your phone (If it is on) and pull out the battery.
8. Connect your phone while battery is out.
9.After connecting your Phone insert your battery...
10. Sp Tool will recognise your Phone and flashing will start.
11. Green circle will show that flash is Done...
Enjoy
NOTE:- Flashing Process and these type of development process may cause any unwanted and unknown errors...So please Try it at your OWN RISK...I will not Responsible for any damge...
Download file is password protected..password is given in download link page...Download is available in small parts as well as in single part also...
post your review please !!
Click to expand...
Click to collapse
My phone is not connecting. i tried many times. help me out plzzz..
Combination
vikphogat said:
My phone is not connecting. i tried many times. help me out plzzz..
Click to expand...
Click to collapse
First of all your have to install VCOM USB drivers for MTK6572 devices....
And then after hitting download button connect your phone while pressing both volume down + up button together....or try this type of different combination....
yes this is most difficult part..i tried 20 times myself....
if not working then try on different machine
As you will be connected there will be an Red and yellow line on SP tool
Next to try..
after hitting download button Press power and volume up button and then connect USB cable while pressing those key together....
Even you can try this new flash tool
http://www.mediafire.com/download/tnas2hjqruf2iht/SP_Flash_Tool_v5.1343.01_by_indiantitaniclover.zip
thanks dude..!!
greatpapa said:
First of all your have to install VCOM USB drivers for MTK6572 devices....
And then after hitting download button connect your phone while pressing both volume down + up button together....or try this type of different combination....
yes this is most difficult part..i tried 20 times myself....
if not working then try on different machine
As you will be connected there will be an Red and yellow line on SP tool
Next to try..
after hitting download button Press power and volume up button and then connect USB cable while pressing those key together....
Even you can try this new flash tool
Click to expand...
Click to collapse
i will try it surely.. can u please also provide me the link to vcom usb drivers for karbonn a12+ ?
thanks in advance.. :laugh::good:
Dri
vikphogat said:
i will try it surely.. can u please also provide me the link to vcom usb drivers for karbonn a12+ ?
thanks in advance.. :laugh::good:
Click to expand...
Click to collapse
New flashtool will recognise direct....Hope so...download new flash tool and try...
greatpapa said:
New flashtool will recognise direct....Hope so...download new flash tool and try...
Click to expand...
Click to collapse
i have tried it nearly 15 16 times. but when i put battery presing and holding volume up + down button phone goes to factory mode. 8 options written in chinese are showing up.
Powrer
vikphogat said:
i have tried it nearly 15 16 times. but when i put battery presing and holding volume up + down button phone goes to factory mode. 8 options written in chinese are showing up.
Click to expand...
Click to collapse
First click on download in flashtool...then press
power + volume up and connect while pressing...Working for me..tested by myself...
hard bricker karbonn a12+........
Great work and nice tutorial some how unbricked my phone 100% working
\\beginers dont post any spam without reading the complete tutorial as I did
thanks a lot for helping
not working
greatpapa said:
First click on download in flashtool...then press
power + volume up and connect while pressing...Working for me..tested by myself...
Click to expand...
Click to collapse
plz help it's not working.installed usb driver & latest sp flash tool.still not working ????
Fastboot
Lovesahota said:
plz help it's not working.installed usb driver & latest sp flash tool.still not working ????
Click to expand...
Click to collapse
Hello....
Try this one..
Switch off your mobile...
Now press volume up + Power button...
Then you will see three option something like Recovery, fastboot, factory...
You have to choose fastboot option...
when fastboot is selected then connect your phone to PC via USB cable...this will install some helpful drivers to your PC....and then again try the flash method without battery...
Stuck at the EYE boot screen of Karbonn A12+. Any help please? Yes, I followed the instructions carefully.
http://playrangers.com/KarbonnA12plus/
in that page the usb drivers of 6577 is provided. Kindly provice MT6572 VCOM drivers.
Process DOne ?
nightcrawler218 said:
Stuck at the EYE boot screen of Karbonn A12+. Any help please? Yes, I followed the instructions carefully.
http://playrangers.com/KarbonnA12plus/
in that page the usb drivers of 6577 is provided. Kindly provice MT6572 VCOM drivers.
Click to expand...
Click to collapse
Did you flashed in proper way ?
means your Sptool recognise your mobile and did you see red and yellow line in sptool and was process done or not ?
greatpapa said:
Did you flashed in proper way ?
means your Sptool recognise your mobile and did you see red and yellow line in sptool and was process done or not ?
Click to expand...
Click to collapse
yeah, everything was according to the tutorial. phone was detected, first red, then blue then yellow progress bar & finally green circle. I removed the usb & reinserted the battery after flashing then pressed the power button. Karbonn animation shown & stuck at the eye screen. After a number of failed attempts I decied to erase the whole device & then flash again. I erased flash+bootloader. The phone is dead now. not powering up. But if I connect the phone via usb to pc a beep sound is heard. Any clue, how to restore the bootloader?
How
nightcrawler218 said:
yeah, everything was according to the tutorial. phone was detected, first red, then blue then yellow progress bar & finally green circle. I removed the usb & reinserted the battery after flashing then pressed the power button. Karbonn animation shown & stuck at the eye screen. After a number of failed attempts I decied to erase the whole device & then flash again. I erased flash+bootloader. The phone is dead now. not powering up. But if I connect the phone via usb to pc a beep sound is heard. Any clue, how to restore the bootloader?
Click to expand...
Click to collapse
How did you erase the Bootloader....??
if you have deleted your bootloader then it would be diffecult to revive the phone
greatpapa said:
How did you erase the Bootloader....??
if you have deleted your bootloader then it would be diffecult to revive the phone
Click to expand...
Click to collapse
I Used SP flash tool to format the device. There was an option for erasing everything (Flash + bootloader).
Will the service center accept my case.?
Ummm
nightcrawler218 said:
I Used SP flash tool to format the device. There was an option for erasing everything (Flash + bootloader).
Will the service center accept my case.?
Click to expand...
Click to collapse
Try again whole method...if you are hearing an beep sound....
Does your mobile is going in recovery mode or fastboot mode ?
Power + volume up (battery is inserted)
greatpapa said:
Try again whole method...if you are hearing an beep sound....
Does your mobile is going in recovery mode or fastboot mode ?
Power + volume up (battery is inserted)
Click to expand...
Click to collapse
Thanks a million times man for your suggestion.
I tried with fastboot but no device shown. I went to device manager & uninstalled-then reinstalled the drivers. That actually helped me to build the serial communication between SP flash tool & Device.
Then I discarded the battery & retried the SP flash tool, this time the phone is finally detected & flashed successfully. red, blue, yellow bar then green circle. DONE.
Now, the same issue. Karbonn boot animation is displayed & stuck at the eye screen. I have covered the halfway but cant be able to get success in the other half (cant see the homescreen or anything.)
---------- Post added at 09:15 PM ---------- Previous post was at 09:07 PM ----------
Phone is OK now but it says INVALID IMEI... any suggestions please...
Good
nightcrawler218 said:
Thanks a million times man for your suggestion.
I tried with fastboot but no device shown. I went to device manager & uninstalled-then reinstalled the drivers. That actually helped me to build the serial communication between SP flash tool & Device.
Then I discarded the battery & retried the SP flash tool, this time the phone is finally detected & flashed successfully. red, blue, yellow bar then green circle. DONE.
Now, the same issue. Karbonn boot animation is displayed & stuck at the eye screen. I have covered the halfway but cant be able to get success in the other half (cant see the homescreen or anything.)
---------- Post added at 09:15 PM ---------- Previous post was at 09:07 PM ----------
Phone is OK now but it says INVALID IMEI... any suggestions please...
Click to expand...
Click to collapse
Don't worry....
Now your phone will be fine....As i will get time i will give you tutorial to write your IMEI number....Till then you can search and google it....your phone is ok...will recover it soon....
Hello to all.
I have a Huawey G700-U00 in my hand that won't boot.
Symptoms:
Alone, push ON button-> nothing
Connected to charger: red light on stable, vibrate every 2 seconds. Stops vibrate only pulling batt out (disconnect don't stop vibrate)
Connected to PC: not recognized at all, rel light stable, vibrate every 2 sec. Stops vibrate only pulling batt out (disconnect don't stop vibrate)
Connected to PC, with VOL+ or VOL- or both VOL pressed: the same as above
In each case display remains black.
Battery is at 3.74 Volts
Water damage indicators are all white.
Anyone has some suggestions?
Thanks in advance.
M.A.
Solved!
I used SP_Flash_Tool to flash a stock ROM.
It's unbrick procedure, discussed along the web for bricked phone with symptoms different from mine.
Have a nice day.
M.A.
dsp_bl
Hello.
the "show" goes on....
Does anyone can sen me a DSP_BL block for this phone, please?
I get in trouble with flash.
I have all blocks ready to flash, but may be I damaged DSP_BL area in the phone.
So phone don't boot and don't accept the flashing
:crying:
Have a nice day.
M.A.
HELLO
maria.aiva said:
Solved!
I used SP_Flash_Tool to flash a stock ROM.
It's unbrick procedure, discussed along the web for bricked phone with symptoms different from mine.
Have a nice day.
M.A.
Click to expand...
Click to collapse
HELLO ,
I have mobile and suffering same problem u had , can u just explain in detail what u did and any links for needed files ,
thanks in advance
maserefiner said:
HELLO ,
I have mobile and suffering same problem u had , can u just explain in detail what u did and any links for needed files ,
thanks in advance
Click to expand...
Click to collapse
This is a clear guide
http://androidmtk.com/fix-huawei-ascend-g700-bootloop
it's for bootloop, but works for bricked also.
(obviously) Hints:
->Flash the RIGHT rom for you mobile
=>Flashing a wrong ROM or wrong PRELOADER results bricked mobile more difficult to unbrik, requires mobile to be open and access the so-known TestPoint on motherboard.
->Ensure your battery is charged enough
Maintain mobile connected to the pc until the end of process
May be you have to swith off Antivirus
Better run FlashTool as administrator (move mouse on file .exe, right click, run as administrator)
(please report if success or not)
Good Luck!
M.A.
P.S.: My mobile is dead now, I suppose due of static electricity of my body/jumper replacing ON/OFF & VOL+/- flex cables...:crying:
didn't work for me
maria.aiva said:
This is a clear guide
http://androidmtk.com/fix-huawei-ascend-g700-bootloop
it's for bootloop, but works for bricked also.
(obviously) Hints:
->Flash the RIGHT rom for you mobile
=>Flashing a wrong ROM or wrong PRELOADER results bricked mobile more difficult to unbrik, requires mobile to be open and access the so-known TestPoint on motherboard.
->Ensure your battery is charged enough
Maintain mobile connected to the pc until the end of process
May be you have to swith off Antivirus
Better run FlashTool as administrator (move mouse on file .exe, right click, run as adm,inistrator)
(please report if success or not)
Good Luck!
M.A.
P.S.: My mobile is dead now, I suppose due of static electricity of my body/jumper replacing ON/OFF & VOL+/- flex cables...:crying:
Click to expand...
Click to collapse
that didn't work for me,
i get error 4008 in sp flash tool
help?
huawei g700 when power on just vibrates. many time try to flash with flash tool but mobile not detect help me plxx