Database Info

O2 XDA Exec Won't Power On after Unccessfull ROM Upgrade

Hi...
I was trying to Upgrade my O2 XDA Exec Rom with Windows Mobile 6.5 by explode. The process went successfully till 99% and after that it ended up with Error. Then I unplugged my pda from the pc and tried to restart the device. I was surprised that the device did not respond to any of the following
Soft Reset
Hard Rest
Boot Loader mode Start (Bulb + Power + Reset)
It is totally blank screen whatever you do.
When I connected the device to the pc with usb cable, a Red Light is shown for 2 seconds and then goes off and a message comes up on the pc that "USB DEVICE NOT RECOGNIZED".
Then I tried to Remove battery from the device for a whole night and the next day morning i did all the above procedures again to get no results.
Kindly Help me out
Thanks
Dinesh Kumaar

I think you have been bricked your device...

dineshkumaar said:
Hi...
I was trying to Upgrade my O2 XDA Exec Rom with Windows Mobile 6.5 by explode. The process went successfully till 99% and after that it ended up with Error. Then I unplugged my pda from the pc and tried to restart the device. I was surprised that the device did not respond to any of the following
Soft Reset
Hard Rest
Boot Loader mode Start (Bulb + Power + Reset)
It is totally blank screen whatever you do.
When I connected the device to the pc with usb cable, a Red Light is shown for 2 seconds and then goes off and a message comes up on the pc that "USB DEVICE NOT RECOGNIZED".
Then I tried to Remove battery from the device for a whole night and the next day morning i did all the above procedures again to get no results.
Kindly Help me out
Thanks
Dinesh Kumaar
Click to expand...
Click to collapse
if it's not recognized, remove the SIM card, the SD card, and on the PC open activesync and disable usb connections. for more info open this link
http://wiki.xda-developers.com/index.php?pagename=Uni_Stuck_Bootloader_Serial

what if the device is bricked
Thanks for your quick reply
Kindly let me know what could be done with the bricked device. Can it be repaired again.
Thanks again
Dinesh Kumaar

dineshkumaar said:
Thanks for your quick reply
Kindly let me know what could be done with the bricked device. Can it be repaired again.
Thanks again
Dinesh Kumaar
Click to expand...
Click to collapse
you have to find another rom and try to flash it to your PDA.
ARE YOU RUNNING windows XP on your PC?

Yes ! I have Windows XP SP2 and Active Sync Version 4.5.0 (Build 5096)
Thanks

dineshkumaar said:
Yes ! I have Windows XP SP2 and Active Sync Version 4.5.0 (Build 5096)
Thanks
Click to expand...
Click to collapse
have you tried to upgrade another ROM, and if you did, is your PDA now working?

I cannot update my rom as my pc cannot recognize my device. is there any other way to update rom?

dineshkumaar said:
I cannot update my rom as my pc cannot recognize my device. is there any other way to update rom?
Click to expand...
Click to collapse
Have you read here?
http://wiki.xda-developers.com/index.php?pagename=Uni_Stuck_Bootloader_Serial
Try to reflash with another ROM
Hope it helped
And don´t forget to vote!

I had already done those steps to get no results.
its my badluck.

If you cannot get into bootloader and you have done the steps above, then you cannot flash to another rom.......it would seem you now have a paperweight im afraid

I am still not able to revive my device. I know that it is just due to corrupt bootloader but don't know how to repair it.
If anybody ever has solution for this... kindly let me know.
Regards

Have you tested mtty?
I would recommend to PM a chef on Universal forum
Good luck,

Mtty is not detecting my device
it says can't open usb port

One More thing I have noted is that when I keep the device connected with the pc, at a certain interval of about 10-15 mintues my device's Led shows RED Light for few seconds and then turns off followed by the the "USB device not recognized" on my pc.
I hope this can be used as a hint towards reviving my device.
Regards

have you followed orbs advise above and pm a chef on that section, they maybe able to help. From my knowledge (limited on that device) i ddont think there is any recovery proceedure that you have not tried. Have u downloaded offical wm5 rom and tried it. I know and appreciate that it will probably not work due to corrupt bootloader, but what else is there to do??
To understand more, what did you do PRIOR to trying to flash to 6.5.
Did you hardspl correctly? Had you already flashed to another rom and just felt like flashing to another new rom?? Give us more detail.

Thanks for your reply
I dont know how to PM Chef.
I had used 3 other Rom versions of WM6.1 on my device. They ran very much fine on my device. But When i found WM6.5 xplode, I wished to try that too. But the rom update procedure went successfully till 99% and after that it showed an error that upgrade was not successfull. I pulled out the device and tried to restart if by all methods but I wasnt able to power on at all.
Thanks
Regards

ok, goto the thread that you got the rom off, click the chefs name and you will get a menu there to send pm, do it, he might have seen a similar problem or know how to correct bootloader.
good luck

noup really no...
Is bricked
my bro has bricked an Universal and the same led turns red no power off no bootloar no power it means the flash chip is dead!
Sorry to heard that.
He waits too long for the upgrade it tooks at least 40 minutes
then ERROR... but you know... the batt was died in middle process ( th batt was ****ed up, it say full charged but no! it was on 60 or 50%) then the stupid thing is make a hardreset.. i told him dont hR your device... justa simple reste and reinit the process... and huh! its bricked.
if you are interested on sell your parts
maybe my bro want some parts.

my advice(similar to other people):
1. Charge your batery somehow (in other device or anything else)
2. put your devce in bootloader mode and connect it to pc - it wll be detected like microsoft usb sync
3. use mtty try difrend versions becuse sometimes 1.42 does not detect it properly - read here for what to do with mtty
IMO this may be battery problem or nand chip problem - in both cases it is hardware fail

[help] sp flash tool usb problems

Hello all,
I have been trying to use the SP FLASH tool to obviously flash the recovery img to my mobile which is teh Prestigio 4500tduo
When ever I click the download button and then connect my mobile it picks it up for about 4-5seconds and disconnects from device manager repeatedly.
things I have tried,
Taking the battery out and holding VOL UP & POWERBUTTON
Leaving the battery in and doing the same above
Trying various of drivers
Tried different USB cables & USB ports
Does anybody know how to fix this ? as when it detects the phone the bar at the bottom of FLASH tool go's to RED & 100% then get an error of 4050 which is probably because it didn't flash correctly.
Hope someone can help me as I nearly through the mobile out of the window in frustration ha
Kind regards
Jadc

bump

Right click on sp flash tool and run it as administrator hopefully it works for you and always use latest version of sp flash tool
Sent from my GT-N7100 using xda premium

Jadc007 said:
Hello all,
I have been trying to use the SP FLASH tool to obviously flash the recovery img to my mobile which is teh Prestigio 4500tduo
When ever I click the download button and then connect my mobile it picks it up for about 4-5seconds and disconnects from device manager repeatedly.
things I have tried,
Taking the battery out and holding VOL UP & POWERBUTTON
Leaving the battery in and doing the same above
Trying various of drivers
Tried different USB cables & USB ports
Does anybody know how to fix this ? as when it detects the phone the bar at the bottom of FLASH tool go's to RED & 100% then get an error of 4050 which is probably because it didn't flash correctly.
Hope someone can help me as I nearly through the mobile out of the window in frustration ha
Kind regards
Jadc
Click to expand...
Click to collapse
If your device appears and then disappears in device manager in 3-4 seconds, then this is normal. i think the problem is with your scatter file. download MTKDroidTool and extract scatter file from your phone, then use this file to flash recovery.

Help me, to fix dead bricked Xperia C c2305

I flashed a wrong recovery img from Mobileuncle tools,from then the phone is not booting,it is not getting detected in Sony pc companion and wmshua flash tools.
Only red led glows for some time,,when connected to pc.
Plz help me

Try this
baselrabia said:
I flashed a wrong recovery img from Mobileuncle tools,from then the phone is not booting,it is not getting detected in Sony pc companion and wmshua flash tools.
Only red led glows for some time,,when connected to pc.
Plz help me
Click to expand...
Click to collapse
I am not a power user. However, It happened to me once. I did the following
1- Open the wmshua flash tools, select the ROM file.
2- Connect a usb.
3- Keep rebooting by holding volume down and Power.
I did not know how it worked for me but it did.
Good luck.
---------- Post added at 04:26 AM ---------- Previous post was at 04:09 AM ----------
Visit this link please.
I cannot post outside link so try this,
Search informationlord dot com
---> ultimate-guide-to-fix-bricked-xperia-c

thutchai said:
I am not a power user. However, It happened to me once. I did the following
1- Open the wmshua flash tools, select the ROM file.
2- Connect a usb.
3- Keep rebooting by holding volume down and Power.
I did not know how it worked for me but it did.
Good luck.
---------- Post added at 04:26 AM ---------- Previous post was at 04:09 AM ----------
Visit this link please.
I cannot post outside link so try this,
Search informationlord dot com
---> ultimate-guide-to-fix-bricked-xperia-c
Click to expand...
Click to collapse
Help Me I Am In Huge Problem , I Had Rooted My Sony Xperia C And Installed 5.0.2 Lollipop Custom Rom But After Somedays The Phone Started Bootlooping Automatically And Now Its Battery Is Fully Drained , I Charged The Phone But Switched Off Charging Battery Symbol Is Not Showing , So I Tried To Flash Sony Xperia C With Flashtool But Flashtool Shows Drivers Not Found m Then I Used WMSHUA Flash Tool But Phone Is Not Detecting , In Device Manager After Connecting Sony Xperia C It Shows "Unknown Device" . i Tried Sony Companion Too,Still Phone Didnt Get Detected , On Device While Charging Or Connecting To Computer Red Led Glows Out , Help Me Please

i keep pushing the buttons.
When it happened to me once. I did the
following,
1- Open the wmshua flash tools,
** I knew that wmshua should detect
phone first, but forget it. **
2- select the ROM file.
3- Connect a usb.
4- Keep rebooting (this is important)
by holding volume down and Power.
keep doing this. In my case i took me
some time. At that moment i have
nothing to lose, so i keep doing this.
And by the way, did you check
the information overlord out?

you need to go to Sony Service Center .
they will charge you around 5k for The New F***G motherboard .
datz all folks .................. mark my word , "DON'T EVER TRY TO MESS WITH ROM'S , KERNAL AND BOOTLOADER" .
if u want to upgrade try buying a new f***ing phone :silly::silly: :good:

Asish RP said:
you need to go to Sony Service Center .
they will charge you around 5k for The New F***G motherboard .
datz all folks .................. mark my word , "DON'T EVER TRY TO MESS WITH ROM'S , KERNAL AND BOOTLOADER" .
if u want to upgrade try buying a new f***ing phone :silly::silly: :good:
Click to expand...
Click to collapse
No, don't mess with the system if there isn't much support or development for it. I regret buying the C3 now because of the horrible camera quality and the fact that the lack of activity is clear. But, it's still a fast phone with good battery management so rooting won't help much.

baselrabia said:
I flashed a wrong recovery img from Mobileuncle tools,from then the phone is not booting,it is not getting detected in Sony pc companion and wmshua flash tools.
Only red led glows for some time,,when connected to pc.
Plz help me
Click to expand...
Click to collapse
Hi.. Have you got this problem solved? Cause i got the same now.. Please any help..
Sent from my Redmi Note 3 using Tapatalk

For me, I've encountered almost the same thing too when flashing my XperiaZ, here's how I fixed it:
Pre-1. To make sure your phone has enough battery left, when holding down the "VolUp" button, connect your phone to a charger. This charges your phone in fastboot mode. It will be slow.
1. In flashtool, open up flashmode, let it load the files (since its a system only flash, you don't need to tick anything) until it prompts you to connect your phone. If the phone is in a boot loop, hold down "Power + VolUp +VolDown" at the same time until it vibrates the hell out of it.
2. When the phone is switched off, hold down the "VolDown" button then quickly connect your phone to your computer. A green light should flash and the phone starts flashing.
3. If this doesn't work, tick the "Wipe Userdata" column so that it can wipe throughly.
Cheers!

KwongTN said:
For me, I've encountered almost the same thing too when flashing my XperiaZ, here's how I fixed it:
Pre-1. To make sure your phone has enough battery left, when holding down the "VolUp" button, connect your phone to a charger. This charges your phone in fastboot mode. It will be slow.
1. In flashtool, open up flashmode, let it load the files (since its a system only flash, you don't need to tick anything) until it prompts you to connect your phone. If the phone is in a boot loop, hold down "Power + VolUp +VolDown" at the same time until it vibrates the hell out of it.
2. When the phone is switched off, hold down the "VolDown" button then quickly connect your phone to your computer. A green light should flash and the phone starts flashing.
3. If this doesn't work, tick the "Wipe Userdata" column so that it can wipe throughly.
Cheers!
Click to expand...
Click to collapse
Thx bro.. I m gonna try it...
Sent from my Redmi Note 3 using Tapatalk

[SOLVED]Lenovo A536 Hard bricked

Hi, please I need your help. I tried to flash stock ROM but I hard bricked my phone. When I connect phone with computer I'm holding volume up button. In device manager it shows "MediaTek USB Port (COM4)" but after three seconds it disconnect. This is why I can't flash ROM. It's everytime disconnect after three seconds.. Please help me.

Maybe you can try to follow this step :http://www.engineerthink.com/blog/2015/11/how-to-unbrick-hard-bricked-android-phone/
If didnt work,maybe there is a problem in your hardware,try to service your phone to service center.

It didn't work.. Is there a way how to solve hardware problem?

Or trt another ways in this website
http://androidflagship.com/3217-fix-damaged-bricked-android-device
My note 10.1 N8000 have the same problem,i try to fix it,but its hard,so i send my phone to service person,they fix the hardware..

How much did you pay?

Growicek said:
Hi, please I need your help. I tried to flash stock ROM but I hard bricked my phone. When I connect phone with computer I'm holding volume up button. In device manager it shows "MediaTek USB Port (COM4)" but after three seconds it disconnect. This is why I can't flash ROM. It's everytime disconnect after three seconds.. Please help me.
Click to expand...
Click to collapse
What tool are you using to flash the stock firmware .and it will be helpful if you say how exactly you bricked it

I'm using SP Flash Tool for flashing.. I tried to flash stock ROM into my Lenovo A536, when it was done I unplugged phone from computer and tried to power on but there was a problem.. Phone was hard bricked

Growicek said:
I'm using SP Flash Tool for flashing.. I tried to flash stock ROM into my Lenovo A536, when it was done I unplugged phone from computer and tried to power on but there was a problem.. Phone was hard bricked
Click to expand...
Click to collapse
So your saying the flashtool bricked your phone ?
Where did you get the firmware for your phone cuz flash tool can only brick your device if you used firmware not for your phone. Also does your phone shows any sign of life ie vibrate turn on for a sec, bootloop etc...

I don't remember where did I find it.. There is only one sign of phone life. When I connect it with computer, phone connect but only for a while, after a three seconds disconnect.

Growicek said:
I don't remember where did I find it.. There is only one sign of phone life. When I connect it with computer, phone connect but only for a while, after a three seconds disconnect.
Click to expand...
Click to collapse
I know two guys who had this problems.
1) guy took it to service ,they fixed it.
2) installed phone drivers again and tried again and it worked.
If you're confident you have the right firmware load scatter click download and connect your powered off phone without pressing any buttons ,and see if it works.
Anyway I'm narrowing down the cause of the problem to either an incorrect firmware or a sp flash tool version (some version are ****)

Didn't work

Growicek said:
Didn't work
Click to expand...
Click to collapse
Pull out the battery then leave it for 10 min reinsert and see if it boots (give it some time ) .if it doesn't
Or connect your phone to PC(without battery) ,load scatter click download on sp flash tool ,then put in the battery .

First method - didn't work
Second method - device automatically disconnect after three seconds, so SP flash tool says error

Growicek said:
First method - didn't work
Second method - device automatically disconnect after three seconds, so SP flash tool says error
Click to expand...
Click to collapse
What error code?
I bricked my device same as you so I could help you further but my device connected in meta mode and flashed its firmware fine ,so try another USB cord
Ps I've pretty much mentioned all I know about unbricking in this thread so I can't be of further help.https://www.google.co.in/url?sa=t&s...ggeMAA&usg=AFQjCNGkwgZbNQCJFWtm90DM-Mksnzk0dA look this up specifically #9

It didn't work.. Error is: BROM ERROR : S_FT_ENABLE_DRAM_FAIL (4032)

Wow! I did something and then uninstalled driver. When I connected phone, driver automatically installed and now it's not disconnecting, but still can't flash it

Growicek said:
Wow! I did something and then uninstalled driver. When I connected phone, driver automatically installed and now it's not disconnecting, but still can't flash it
Click to expand...
Click to collapse
That's great ,what's the problem now ? Still brom error or download stuck st 0% or any other?

Still same brom error

Growicek said:
Still same brom error
Click to expand...
Click to collapse
Brom error is mostly related to see improper firmware which also explains why you're phone got bricked in the first place .
Try downloading another stock firmware

Man? I love you!!! I tried about four ROMs and the fourth is working!! .. There was a one more problem with flashing again with drivers, idk why but they dissapear, so I installed them again and then tried flash ROM.. Thank you very much! You saved my money!

Accidental wrong flash with Flashtool

Looks like I killed my Z5. The model is 6683 (Z5 dual), and I flashed with E6533 (Z3+ dual).
The phone is completely dead, cannot turn on, not vibrating on power button etc.
When I connect to my laptop, it says "unable to recognize USB device", in detail VID_0000&PID_0000.
But if I disconnect the battery, it recognized as "SOMC Flash device", VID_0FCE&PID_DDDE
Is it possible to resurrect it?
I hope if I can flash with correct bootloader in this state, it will enought to boot up and able to flash with the right firmware.

Macs1209 said:
Looks like I killed my Z5. The model is 6683 (Z5 dual), and I flashed with E6533 (Z3+ dual).
The phone is completely dead, cannot turn on, not vibrating on power button etc.
When I connect to my laptop, it says "unable to recognize USB device", in detail VID_0000&PID_0000.
But if I disconnect the battery, it recognized as "SOMC Flash device", VID_0FCE&PID_DDDE
Is it possible to resurrect it?
I hope if I can flash with correct bootloader in this state, it will enought to boot up and able to flash with the right firmware.
Click to expand...
Click to collapse
Are you able to connect it in flashmode and fastboot ?

With battery, no.
Without battery, my laptop recognize as "SOMC Flash device", but no tool can connect to it (like FlashTool).
(I think then different PID is the reason)

Macs1209 said:
With battery, no.
Without battery, my laptop recognize as "SOMC Flash device", but no tool can connect to it (like FlashTool).
(I think then different PID is the reason)
Click to expand...
Click to collapse
it seems to me that you are an advanced person in playing with your mobile, this kind of issues is beyond of my knowledge but I was replying to your thread hopefully someone here can help, I'm fearing that you have messed up with your mobile

Well, you could try to flash it from Ubuntu (NOT inside Windows 10 !) via FlashTool,
under windows there are limitations with different device IDs that separate drivers would be needed (and if only "wrong" ID is detected under Linux it doesn't really matter, since it's detected anyway),
perhaps under Linux operating systems you have more luck

Thank you for idea, but not working.
Finally I found an old SETool3 box , and successfully flashed with it without battery
Somehow it can fixed it.

Macs1209 said:
Thank you for idea, but not working.
Finally I found an old SETool3 box , and successfully flashed with it without battery
Somehow it can fixed it.
Click to expand...
Click to collapse
I am facing a similar situation, can you help me by telling me what exactly did you do to solve the issue step by step?

Same Problem With Me PLZ HELP
Dear Bro Ive same problem with my Xperia e6683 Total Dead After Wrong Flash with Xperia Z3+ File... SO Plz help me how to fit step by step guide plz....
As on 20 Jan 2017
I've Flash Successfully It With Setool fusion Box Without Battery Use Test Pin Method. Now My My Phone Again Alive..

[email protected] said:
Dear Bro Ive same problem with my Xperia e6683 Total Dead After Wrong Flash with Xperia Z3+ File... SO Plz help me how to fit step by step guide plz....
As on 20 Jan 2017
I've Flash Successfully It With Setool fusion Box Without Battery Use Test Pin Method. Now My My Phone Again Alive..
Click to expand...
Click to collapse
Dear Bro Ive same problem with my Xperia x Total Dead After Wrong Flash
The phone is completely dead, cannot turn on, not vibrating on power button etc.
When I connect to my laptop, it says "unable to recognize USB device"
using test pin method it is recognized as "SOMC Flash device"
i have backup ta partition and ftf firmware of my xperia i can't find any tool to flash
can you guide me please

Flashtool Doesn't Recognise This Device. U can use Setool/ Setool Fusion Box to Repai
bma1973 said:
Dear Bro Ive same problem with my Xperia x Total Dead After Wrong Flash
The phone is completely dead, cannot turn on, not vibrating on power button etc.
When I connect to my laptop, it says "unable to recognize USB device"
using test pin method it is recognized as "SOMC Flash device"
i have backup ta partition and ftf firmware of my xperia i can't find any tool to flash
can you guide me please
Click to expand...
Click to collapse
Bro
In this Condition Flashtool Not Recognised Ur Device. There is only a best solution U Can Use SETOOL/SETOOL FUSION BOX To Repair/ Flash Ur Device.

[email protected] said:
Dear Bro Ive same problem with my Xperia e6683 Total Dead After Wrong Flash with Xperia Z3+ File... SO Plz help me how to fit step by step guide plz....
As on 20 Jan 2017
I've Flash Successfully It With Setool fusion Box Without Battery Use Test Pin Method. Now My My Phone Again Alive..
Click to expand...
Click to collapse
bma1973 said:
Dear Bro Ive same problem with my Xperia x Total Dead After Wrong Flash
The phone is completely dead, cannot turn on, not vibrating on power button etc.
When I connect to my laptop, it says "unable to recognize USB device"
using test pin method it is recognized as "SOMC Flash device"
i have backup ta partition and ftf firmware of my xperia i can't find any tool to flash
can you guide me please
Click to expand...
Click to collapse
wrong flash means wrong kernel!
you might be stuck on black screen when you frist switchon device! the device is running! but since its stuck on bootloops no interface is open!
press power and volume up button for 15+ seconds and let it JERK 3 times , this if force shutdown. the device should get connected now in flashmode