Hi, please I need your help. I tried to flash stock ROM but I hard bricked my phone. When I connect phone with computer I'm holding volume up button. In device manager it shows "MediaTek USB Port (COM4)" but after three seconds it disconnect. This is why I can't flash ROM. It's everytime disconnect after three seconds.. Please help me.
Maybe you can try to follow this step :http://www.engineerthink.com/blog/2015/11/how-to-unbrick-hard-bricked-android-phone/
If didnt work,maybe there is a problem in your hardware,try to service your phone to service center.
It didn't work.. Is there a way how to solve hardware problem?
Or trt another ways in this website
http://androidflagship.com/3217-fix-damaged-bricked-android-device
My note 10.1 N8000 have the same problem,i try to fix it,but its hard,so i send my phone to service person,they fix the hardware..
How much did you pay?
Growicek said:
Hi, please I need your help. I tried to flash stock ROM but I hard bricked my phone. When I connect phone with computer I'm holding volume up button. In device manager it shows "MediaTek USB Port (COM4)" but after three seconds it disconnect. This is why I can't flash ROM. It's everytime disconnect after three seconds.. Please help me.
Click to expand...
Click to collapse
What tool are you using to flash the stock firmware .and it will be helpful if you say how exactly you bricked it
I'm using SP Flash Tool for flashing.. I tried to flash stock ROM into my Lenovo A536, when it was done I unplugged phone from computer and tried to power on but there was a problem.. Phone was hard bricked
Growicek said:
I'm using SP Flash Tool for flashing.. I tried to flash stock ROM into my Lenovo A536, when it was done I unplugged phone from computer and tried to power on but there was a problem.. Phone was hard bricked
Click to expand...
Click to collapse
So your saying the flashtool bricked your phone ?
Where did you get the firmware for your phone cuz flash tool can only brick your device if you used firmware not for your phone. Also does your phone shows any sign of life ie vibrate turn on for a sec, bootloop etc...
I don't remember where did I find it.. There is only one sign of phone life. When I connect it with computer, phone connect but only for a while, after a three seconds disconnect.
Growicek said:
I don't remember where did I find it.. There is only one sign of phone life. When I connect it with computer, phone connect but only for a while, after a three seconds disconnect.
Click to expand...
Click to collapse
I know two guys who had this problems.
1) guy took it to service ,they fixed it.
2) installed phone drivers again and tried again and it worked.
If you're confident you have the right firmware load scatter click download and connect your powered off phone without pressing any buttons ,and see if it works.
Anyway I'm narrowing down the cause of the problem to either an incorrect firmware or a sp flash tool version (some version are ****)
Didn't work
Growicek said:
Didn't work
Click to expand...
Click to collapse
Pull out the battery then leave it for 10 min reinsert and see if it boots (give it some time ) .if it doesn't
Or connect your phone to PC(without battery) ,load scatter click download on sp flash tool ,then put in the battery .
First method - didn't work
Second method - device automatically disconnect after three seconds, so SP flash tool says error
Growicek said:
First method - didn't work
Second method - device automatically disconnect after three seconds, so SP flash tool says error
Click to expand...
Click to collapse
What error code?
I bricked my device same as you so I could help you further but my device connected in meta mode and flashed its firmware fine ,so try another USB cord
Ps I've pretty much mentioned all I know about unbricking in this thread so I can't be of further help.https://www.google.co.in/url?sa=t&s...ggeMAA&usg=AFQjCNGkwgZbNQCJFWtm90DM-Mksnzk0dA look this up specifically #9
It didn't work.. Error is: BROM ERROR : S_FT_ENABLE_DRAM_FAIL (4032)
Wow! I did something and then uninstalled driver. When I connected phone, driver automatically installed and now it's not disconnecting, but still can't flash it
Growicek said:
Wow! I did something and then uninstalled driver. When I connected phone, driver automatically installed and now it's not disconnecting, but still can't flash it
Click to expand...
Click to collapse
That's great ,what's the problem now ? Still brom error or download stuck st 0% or any other?
Still same brom error
Growicek said:
Still same brom error
Click to expand...
Click to collapse
Brom error is mostly related to see improper firmware which also explains why you're phone got bricked in the first place .
Try downloading another stock firmware
Man? I love you!!! I tried about four ROMs and the fourth is working!! .. There was a one more problem with flashing again with drivers, idk why but they dissapear, so I installed them again and then tried flash ROM.. Thank you very much! You saved my money!
Related
i am loosing it....
i tried every thread about bricked phone - and nothing solved my problem.
it all started when i tried to use th LG FLASH TOOL to upgrade firmware and by mistake i checked "Erase Entire AP" and since than my phone wont turn on.
when i connect the usb cable - i get a notification of OMAP443 but it goes on and off rapidly like it is connecting and disconnecting at the same time - not stable.
i download all drivers, even tried to manual fix the driver with the inf file, but nothing - still unstable.
i also bought a special usb cable that has 56K-130K-910K - i tried all modes but did not get the download mode screen as shown in one of the guides here.
i need to stable the connection between the phone and the pc so i can flash the firmware.
any suggestions ?
please help - anyone :crying:
You have probably used Smartflash,not Lg flashtool.
I can make your phone to stay connected to pc but you won't be able to flash anything
Your phone's cpu is in debug mode now.
Signed bootloaders are needed to recover it with Linux, or a script for omapflash for recovering with windows..
tsvikariz said:
i am loosing it....
i tried every thread about bricked phone - and nothing solved my problem.
it all started when i tried to use th LG FLASH TOOL to upgrade firmware and by mistake i checked "Erase Entire AP" and since than my phone wont turn on.
when i connect the usb cable - i get a notification of OMAP443 but it goes on and off rapidly like it is connecting and disconnecting at the same time - not stable.
i download all drivers, even tried to manual fix the driver with the inf file, but nothing - still unstable.
i also bought a special usb cable that has 56K-130K-910K - i tried all modes but did not get the download mode screen as shown in one of the guides here.
i need to stable the connection between the phone and the pc so i can flash the firmware.
any suggestions ?
please help - anyone :crying:
Click to expand...
Click to collapse
uses this method recovers bricked
http://www.htcspain.com/roms-lg-opt...cambiar-baseband-por-el-metodo-del-fls-53449/
will get my phone back in a couple of days and will give it a try - i hope those methods will help.
tsvikariz said:
will get my phone back in a couple of days and will give it a try - i hope those methods will help.
Click to expand...
Click to collapse
Does it work?
I was upgrading my Xperia TO 5.1 and was flashing recovery. TWRP was flashed but I was not able to flash any zip through it.
I tried unlocking bootloader but nothing happened. I tried this 3-4 times and suddenly my Phone gone blank.
Now the condition is neither LED or any kind of vibration is working. Phone is detected as Qualcomm Qloader 9008. I tried figuring out and found that bootloader is corrupt. Many person having Snapdragon Chipset have same problem. I found EMMC DL Tool which can repair this but in version 5.2.0.r I am getting invalid user error.
Then I tried Tool studio EMMC tool from ZTE but I am getting error while downloading the Hex file. Phone is detected but unfortunately I am not able to fix it.
Please go through screenshot.
Someone please help me to fix. Either using this emmc tool or anyother.
P.S. Went to SC they said to replace MB which will cost around 6500-7500. But I don't think to spend such money for repairing when I can but much better phone in that price segment.
I am not able to post image. Help me. I don't have 10 post count yet.
nik_123 said:
I was upgrading my Xperia TO 5.1 and was flashing recovery. TWRP was flashed but I was not able to flash any zip through it.
I tried unlocking bootloader but nothing happened. I tried this 3-4 times and suddenly my Phone gone blank.
Now the condition is neither LED or any kind of vibration is working. Phone is detected as Qualcomm Qloader 9008. I tried figuring out and found that bootloader is corrupt. Many person having Snapdragon Chipset have same problem. I found EMMC DL Tool which can repair this but in version 5.2.0.r I am getting invalid user error.
Then I tried Tool studio EMMC tool from ZTE but I am getting error while downloading the Hex file. Phone is detected but unfortunately I am not able to fix it.
Please go through screenshot.
Someone please help me to fix. Either using this emmc tool or anyother.
P.S. Went to SC they said to replace MB which will cost around 6500-7500. But I don't think to spend such money for repairing when I can but much better phone in that price segment.
Click to expand...
Click to collapse
So, you cannot get into flashmode or fastboot? Power off your phone, hold volume up and plug it into your pc without hitting the power button. Do you get any blue led or quick led flash at all? I'm not sure about your device's condition but I can surely try getting you files from my phone.
Try installing flashtool and see if flashtool recognizes your phone at all.
Agent_fabulous said:
So, you cannot get into flashmode or fastboot? Power off your phone, hold volume up and plug it into your pc without hitting the power button. Do you get any blue led or quick led flash at all? I'm not sure about your device's condition but I can surely try getting you files from my phone.
Try installing flashtool and see if flashtool recognizes your phone at all.
Click to expand...
Click to collapse
Only red LED glows while I plug it in PC. Flashtool can not recognize. EMMC tool recognize but can't find/download the files.
I am pretty sure once I get the tool running it will bring back my phone alive.
nik_123 said:
Only red LED glows while I plug it in PC. Flashtool can not recognize. EMMC tool recognize but can't find/download the files.
I am pretty sure once I get the tool running it will bring back my phone alive.
Click to expand...
Click to collapse
Hmm, can QPST find your phone? I'm trying to get a QPST/QCN backup which could be helpful. However, fastboot, flashmode, recovery or device running, I get ports empty. Can anyone help me out here? I can try draining my battery so I have the little phase of the dull red led where the device won't power on until it's a little charged.
Agent_fabulous said:
Hmm, can QPST find your phone? I'm trying to get a QPST/QCN backup which could be helpful. However, fastboot, flashmode, recovery or device running, I get ports empty. Can anyone help me out here? I can try draining my battery so I have the little phase of the dull red led where the device won't power on until it's a little charged.
Click to expand...
Click to collapse
I guess yes, but I don't remember exactly. Switch off your phone and connect may be it should detect.
nik_123 said:
I guess yes, but I don't remember exactly. Switch off your phone and connect may be it should detect.
Click to expand...
Click to collapse
Tried that but it ends up turning on and goes to the charging animation. (Which is after the Sony Logo.) Waiting for my phone to drain
nik_123 said:
I was upgrading my Xperia TO 5.1 and was flashing recovery. TWRP was flashed but I was not able to flash any zip through it.
I tried unlocking bootloader but nothing happened. I tried this 3-4 times and suddenly my Phone gone blank.
Now the condition is neither LED or any kind of vibration is working. Phone is detected as Qualcomm Qloader 9008. I tried figuring out and found that bootloader is corrupt. Many person having Snapdragon Chipset have same problem. I found EMMC DL Tool which can repair this but in version 5.2.0.r I am getting invalid user error.
Then I tried Tool studio EMMC tool from ZTE but I am getting error while downloading the Hex file. Phone is detected but unfortunately I am not able to fix it.
Please go through screenshot.
Someone please help me to fix. Either using this emmc tool or anyother.
P.S. Went to SC they said to replace MB which will cost around 6500-7500. But I don't think to spend such money for repairing when I can but much better phone in that price segment.
Click to expand...
Click to collapse
Jesus Christ, you installed a ROM without unlocking the bootloader first?... yare yare daze...
stuckbootloader said:
Jesus Christ, you installed a ROM without unlocking the bootloader first?... yare yare daze...
Click to expand...
Click to collapse
I unlocked it but the ROM zip was not flashing through TWRP. After 2-3 tries my phone went full dead. If you can help it will be great.
nik_123 said:
I unlocked it but the ROM zip was not flashing through TWRP. After 2-3 tries my phone went full dead. If you can help it will be great.
Click to expand...
Click to collapse
I'm afraid I can't...
Agent_fabulous said:
Tried that but it ends up turning on and goes to the charging animation. (Which is after the Sony Logo.) Waiting for my phone to drain
Click to expand...
Click to collapse
eh... if your device is showing loading anymation this means charger is loaded.... so no you dont have a hardbrick... try to reach fastbootmode over and over again
Sent from my Xperia T using XDA Free mobile app
SdtBarbarossa said:
eh... if your device is showing loading anymation this means charger is loaded.... so no you dont have a hardbrick... try to reach fastbootmode over and over again
Sent from my Xperia T using XDA Free mobile app
Click to expand...
Click to collapse
My phone is working fine. However, I've no idea how to get a QPST/QCN Backup (which I guess could) help out @nik_123
Agent_fabulous said:
My phone is working fine. However, I've no idea how to get a QPST/QCN Backup (which I guess could) help out @nik_123
Click to expand...
Click to collapse
nope... even if we have a snapdragon... since this is a semcflash device a backup is useless...
Sent from my Xperia T using XDA Free mobile app
Hello sir,
I had the same problem a month ago and I fixed my bricked Xperia L.
Just go to this thread and follow the steps ^^
http://forum.xda-developers.com/showthread.php?t=2695344
The thread says u need to download WMSHUA, but its in chinese language. If you don't know what it means just reply to this and i will translate it.
Good luck!
If it didn't worked, or u need help reply.
Good day gents and ladies
Well let me start from the beginning.
I'm was using mi-globe 6.12.22
Last week Friday evening downloaded 7.2.9 mi-globe,read around the mi-globe forum.Didn't see anything funny so flashed via twrp on Saturday morning.Hmmmmmmmm this is when all my problems started.
Basically what I should of done is download 7.2.9,new 3.0.3 twrp for norgat,go into recovery flash new recovery, restart recovery,flash 7.2.9 and then have happy days.But it wasn't to be and now I'm basically sitting with a useless mi4c device.
The device works but warms up and I only get about 4 hours battery life.
If I try boot into recovery I just get black screen.
If I connect device to PC it is not recognized, have tried 3 x different laptop/PC's and different cables.
So fastboot,mi-flash,mi-unlock are all not possible as device is not recognized.
I have been trying different solutions without any success.
I think if it would be possible to root device directly without PC then maybe it will be possible to get flashfire working and I can flash new norgat recovery?
Any suggestions would be greatly appreciated?
NB.I have tried loading Qualcomm drivers ,google drivers etc etc.no luck can't connect my device too PC,either get device not recognized or the PC doesn't even see the device.Enable USB debugging etc etc nothing works.Been fiddling for 4 days!!!!!!!
Tried to root with kingoroot,framaroot directly on device etc nothing works?
Please help,else device is a nice piece of plastic that holds paper down on my table.lol
BR
Ant
have you tried fastboot
fastboot oem edl
Click to expand...
Click to collapse
then MiFlash to flash official rom
Fastboot don't work,as PC don't see the phone?
DeAntman said:
Fastboot don't work,as PC don't see the phone?
Click to expand...
Click to collapse
Is usb charging via pc working and have you tried miui updater? , This seems weird state you have ... If none working might be tried deep flash cable flashing ... Or go to nearest service center. Hope that help. Best luck.
Hi,yes USB chargers device via PC but that's all.
How does one deep flash,could you post link please?
I bought the device in China about 18 months ago,Xiaomi never sold mi4c in my country so doubt they could help me locally.
Seems I have soft bricked the device?Tried every thing no solution.
If it would possible to root without USB cable I could maybe try flash new twrp via flash fire?Then could wipe all and try start again?
DeAntman said:
Hi,yes USB chargers device via PC but that's all.
How does one deep flash,could you post link please?
I bought the device in China about 18 months ago,Xiaomi never sold mi4c in my country so doubt they could help me locally.
Seems I have soft bricked the device?Tried every thing no solution.
If it would possible to root without USB cable I could maybe try flash new twrp via flash fire?Then could wipe all and try start again?
Click to expand...
Click to collapse
You havent answered the miui updater part, have you tried flash miui rom.zip, using miui updater apps ?
Does fastboot mode boot on your phone ? i mean the bunny sceen showed up ?
For dfc here the link http://xiaomitips.com/guide/miui-deep-flash-engineering-cable-solution-to-non-edl-device/
Please take dfc as last resort. And do research more on this... Do with your own risk. Good luck
Hi,
Yes sorry I have tried updater, I download rom start updater it starts but after about 2 minutes stops and phones shuts down.
I then have to restart phone with long press of power button. It restarts but nothing has changed.
Wrt fastboot it goes into fastboot but this is useless cause no Pc can see my device and if it sees it it sees unknown device, spent countless hours trying different things without any success.
Seems have soft bricked the device, phone works but gets hot and battery life maybe 4 hours if I'm lucky?
Not sure what more today?
DeAntman said:
Hi,
Yes sorry I have tried updater, I download rom start updater it starts but after about 2 minutes stops and phones shuts down.
I then have to restart phone with long press of power button. It restarts but nothing has changed.
Wrt fastboot it goes into fastboot but this is useless cause no Pc can see my device and if it sees it it sees unknown device, spent countless hours trying different things without any success.
Seems have soft bricked the device, phone works but gets hot and battery life maybe 4 hours if I'm lucky?
Not sure what more today?
Click to expand...
Click to collapse
Before this has your pc able to use the miflash ? Try to follow this guide to setup it correctly http://en.miui.com/thread-136188-1-1.html ... I follow this guide and the adb n fastboot even works on an old pentium 4, 512mb ram, win xp laptop.
Ps: I think, its only a matter of incorrect driver setup on your side, best luck.
Looks like I killed my Z5. The model is 6683 (Z5 dual), and I flashed with E6533 (Z3+ dual).
The phone is completely dead, cannot turn on, not vibrating on power button etc.
When I connect to my laptop, it says "unable to recognize USB device", in detail VID_0000&PID_0000.
But if I disconnect the battery, it recognized as "SOMC Flash device", VID_0FCE&PID_DDDE
Is it possible to resurrect it?
I hope if I can flash with correct bootloader in this state, it will enought to boot up and able to flash with the right firmware.
Macs1209 said:
Looks like I killed my Z5. The model is 6683 (Z5 dual), and I flashed with E6533 (Z3+ dual).
The phone is completely dead, cannot turn on, not vibrating on power button etc.
When I connect to my laptop, it says "unable to recognize USB device", in detail VID_0000&PID_0000.
But if I disconnect the battery, it recognized as "SOMC Flash device", VID_0FCE&PID_DDDE
Is it possible to resurrect it?
I hope if I can flash with correct bootloader in this state, it will enought to boot up and able to flash with the right firmware.
Click to expand...
Click to collapse
Are you able to connect it in flashmode and fastboot ?
With battery, no.
Without battery, my laptop recognize as "SOMC Flash device", but no tool can connect to it (like FlashTool).
(I think then different PID is the reason)
Macs1209 said:
With battery, no.
Without battery, my laptop recognize as "SOMC Flash device", but no tool can connect to it (like FlashTool).
(I think then different PID is the reason)
Click to expand...
Click to collapse
it seems to me that you are an advanced person in playing with your mobile, this kind of issues is beyond of my knowledge but I was replying to your thread hopefully someone here can help, I'm fearing that you have messed up with your mobile
Well, you could try to flash it from Ubuntu (NOT inside Windows 10 !) via FlashTool,
under windows there are limitations with different device IDs that separate drivers would be needed (and if only "wrong" ID is detected under Linux it doesn't really matter, since it's detected anyway),
perhaps under Linux operating systems you have more luck
Thank you for idea, but not working.
Finally I found an old SETool3 box , and successfully flashed with it without battery
Somehow it can fixed it.
Macs1209 said:
Thank you for idea, but not working.
Finally I found an old SETool3 box , and successfully flashed with it without battery
Somehow it can fixed it.
Click to expand...
Click to collapse
I am facing a similar situation, can you help me by telling me what exactly did you do to solve the issue step by step?
Same Problem With Me PLZ HELP
Dear Bro Ive same problem with my Xperia e6683 Total Dead After Wrong Flash with Xperia Z3+ File... SO Plz help me how to fit step by step guide plz....
As on 20 Jan 2017
I've Flash Successfully It With Setool fusion Box Without Battery Use Test Pin Method. Now My My Phone Again Alive..
[email protected] said:
Dear Bro Ive same problem with my Xperia e6683 Total Dead After Wrong Flash with Xperia Z3+ File... SO Plz help me how to fit step by step guide plz....
As on 20 Jan 2017
I've Flash Successfully It With Setool fusion Box Without Battery Use Test Pin Method. Now My My Phone Again Alive..
Click to expand...
Click to collapse
Dear Bro Ive same problem with my Xperia x Total Dead After Wrong Flash
The phone is completely dead, cannot turn on, not vibrating on power button etc.
When I connect to my laptop, it says "unable to recognize USB device"
using test pin method it is recognized as "SOMC Flash device"
i have backup ta partition and ftf firmware of my xperia i can't find any tool to flash
can you guide me please
Flashtool Doesn't Recognise This Device. U can use Setool/ Setool Fusion Box to Repai
bma1973 said:
Dear Bro Ive same problem with my Xperia x Total Dead After Wrong Flash
The phone is completely dead, cannot turn on, not vibrating on power button etc.
When I connect to my laptop, it says "unable to recognize USB device"
using test pin method it is recognized as "SOMC Flash device"
i have backup ta partition and ftf firmware of my xperia i can't find any tool to flash
can you guide me please
Click to expand...
Click to collapse
Bro
In this Condition Flashtool Not Recognised Ur Device. There is only a best solution U Can Use SETOOL/SETOOL FUSION BOX To Repair/ Flash Ur Device.
[email protected] said:
Dear Bro Ive same problem with my Xperia e6683 Total Dead After Wrong Flash with Xperia Z3+ File... SO Plz help me how to fit step by step guide plz....
As on 20 Jan 2017
I've Flash Successfully It With Setool fusion Box Without Battery Use Test Pin Method. Now My My Phone Again Alive..
Click to expand...
Click to collapse
bma1973 said:
Dear Bro Ive same problem with my Xperia x Total Dead After Wrong Flash
The phone is completely dead, cannot turn on, not vibrating on power button etc.
When I connect to my laptop, it says "unable to recognize USB device"
using test pin method it is recognized as "SOMC Flash device"
i have backup ta partition and ftf firmware of my xperia i can't find any tool to flash
can you guide me please
Click to expand...
Click to collapse
wrong flash means wrong kernel!
you might be stuck on black screen when you frist switchon device! the device is running! but since its stuck on bootloops no interface is open!
press power and volume up button for 15+ seconds and let it JERK 3 times , this if force shutdown. the device should get connected now in flashmode
Hey Friends,
You must have seen very good days with Lenovo P2 but when there comes a bad day when your phone stops responding to button holds and restarts. You may or may not have a clue what to do to get your phone working again just like before.
I got into this situation where only thing my phone was able to operate was a RED LED on connecting it to my laptop. Then I had to read tens of pages on XDA to find answers to all my questions. If you are in such a situation and your phone is UNLOCKED then you have come to the right place. Procedure is quite simple but remember, I am writing this guide to define complete process from blackout to complete update so follow this guide as per your needs.
I faced this situation of Total Blackout / Dead Phone (Almost) with only Red LED working and it can be very scary. So, here is the simplest procedure you can follow. I want to appreciate all those people who helped me in finding a way to boot my phone with each and everything working. Long story short, let's get this done.
Tools Required:
I am mentioning here all the Tools you will need. I will urge you to download and save these tools in case you want to unbrick your phone any time:
1. Minimal ADB and Fastboot setup for PC
2. Lenovo USB drivers v1.1.33
3. Qualcomm USB Drivers
4. Qualcomm Flash Image Loader (QFIL) v2.0.1.9 for your PC in case you have corrupted your phone's IMEI and/ or Baseband
5. Blankflash.bat in case you want to recover from total blackout (Attached)
6. Stock MM S048 Firmware for Lenovo P2 in case phone doesn't boot
7. S048_ModemTelephony.zip in case your phone boots through Stock MM S048 but SIM isn't detected and IMEI is missing. I have made a complete modem zip file for installation through recovery.
8. S251_ModemTelephony.zip in case your phone is on latest firmware and doesn't detect SIM and has lost IMEI. I have made a complete modem zip file for installation through recovery.
9. QCN file for recovering baseband version and giving you most precious network signals. (Attached)
10. WinRAR or PeaZip for uncompressing files
I will recommend you to have a specific folder for keeping all these tools in a single place.
Procedure for Unbricking:
Before going with the procedure, make sure you have downloaded all the files you need, updated Lenovo and Qualcomm drivers etc. Here is the procedure:
1. If total blackout with red LED notification when connecting to PC: Unzip blankflash.zip to a folder in C drive. Now connect your P2 to PC through USB, press volume+, volume- and power button simultaneously and double click blankflash.bat. You might have no success in your first try. Just keep trying and it will load your phone to Fastboot. Restart your phone in TWRP if installed and install a working ROM for your phone after doing a wipe. If all is good and phone works OK then great but if you have lost IMEI and baseband then it is better to reinstate your phone through first MM stock ROM S048
2. Install S048 firmware through Minimal ADB and Fastboot - use flash instructions in .txt file.
3. Wait for startup of phone. Check if fingerprint, BT, WIFI and SIM work if all work then OK.
4. If fingerprint, BT, WIFI and SIM are not working then check IMEI through dialer. Dial *#06#. If IMEI is not available then install latest TWRP through Fastboot.
5. Start P2 in TWRP recovery and install S048_ModemTelephony.zip. Restart phone to see if WIFI and SIM work.
6. If SIM is detected but not giving signals and Baseband is shown as unknown then extract 000000_0.qcn file given in .7z and restore through QFIL and restart your phone into Fastboot.
7. Now, install stock recovery of S048 firmware through Fastboot and restart your phone.
8. Use your phone like you normally do and update your P2 till firmware S251 and see if everything works including calls. Update your phone through OTA.
9. After OTA installation, stock recovery may say that update failed. Just press Back, go into Wipe user data menu and Wipe Cache only. Restart your phone which will be updated to latest version and will ask you to update to a newer version. Allow it to download the next update.
10. After installation of S251 update, install latest TWRP through Fastboot and install most recent version of LOS 16 so that your vendor partition is stable and free from any bloated files. Now, use your phone just like you want to.
If you need further clarification then ask in this thread.
Bro my phone is not unlocked can i try thz one
Ranji007 said:
Bro my phone is not unlocked can i try thz one
Click to expand...
Click to collapse
You should download S048 and use flashall.bat inside that archive to install it all. However, if you lose IMEI or baseband then you can use modem and qcn files given in this thread.
alirazaagha said:
You should download S048 and use flashall.bat inside that archive to install it all. However, if you lose IMEI or baseband then you can use modem and qcn files given in this thread.
Click to expand...
Click to collapse
Bro now i wanna use ...minimal adb ..my phone is totally bricked only red light glowing
Ranji007 said:
Bro now i wanna use ...minimal adb ..my phone is totally bricked only red light glowing
Click to expand...
Click to collapse
don't worry just flash blank flash from the link given in the op, you will get the bootloader back
hackiee said:
don't worry just flash blank flash from the link given in the op, you will get the bootloader back
Click to expand...
Click to collapse
Bro how to connect my phone to blank flash...can u PLZZ help
hackiee said:
don't worry just flash blank flash from the link given in the op, you will get the bootloader back
Click to expand...
Click to collapse
Laptop is not detecting my device bro i installed all lenovo and Qualcomm drivers...any idea
Ranji007 said:
Laptop is not detecting my device bro i installed all lenovo and Qualcomm drivers...any idea
Click to expand...
Click to collapse
If red light blinks, your phone can be detected by your laptop. Check ports in device manager settings and you'll see a new port with Qualcomm 9800 series number. If that's there, try blankflash to start in fastboot. It might need some tries before startup. Be patient and keep trying till you are in fastboot.
alirazaagha said:
If red light blinks, your phone can be detected by your laptop. Check ports in device manager settings and you'll see a new port with Qualcomm 9800 series number. If that's there, try blankflash to start in fastboot. It might need some tries before startup. Be patient and keep trying till you are in fastboot.
Click to expand...
Click to collapse
Bro ..thanks for reply....in my phone red blink is glowing continuously ..but after connecting there is no change...can u say which buttons i want to press?
Ranji007 said:
Bro ..thanks for reply....in my phone red blink is glowing continuously ..but after connecting there is no change...can u say which buttons i want to press?
Click to expand...
Click to collapse
Press Volume+, Volume- and Power simultaneously and double click flashblank.bat. It might take some tries to finally install the scripts and start phone in fastboot. It took me 20+ tries to finally detect my phone through blankflash. Please, read OP completely.
alirazaagha said:
Press Volume+, Volume- and Power simultaneously and double click flashblank.bat. It might take some tries to finally install the scripts and start phone in fastboot. It took me 20+ tries to finally detect my phone through blankflash. Please, read OP completely.
Click to expand...
Click to collapse
Bro we want to connect each time removing usb cable and connect again like that ..we wanna do 20 times??
Ranji007 said:
Bro we want to connect each time removing usb cable and connect again like that ..we wanna do 20 times??
Click to expand...
Click to collapse
No. Keep USB connected. Try blankflash. If it doesn't detect phone or go ahead. Close command terminal, double click again and keep doing it till it processes the files. If it is stuck somewhere. Close terminal and try again.
alirazaagha said:
No. Keep USB connected. Try blankflash. If it doesn't detect phone or go ahead. Close command terminal, double click again and keep doing it till it processes the files. If it is stuck somewhere. Close terminal and try again.
Click to expand...
Click to collapse
Bro is there any solution ..i continuously pressed volume and power buttons connected to laptop and opening blank flash continuously for number of times ...but there was no reaction...only waiting for device is showing ? on my pc ...
Ranji007 said:
Bro is there any solution ..i continuously pressed volume and power buttons connected to laptop and opening blank flash continuously for number of times ...but there was no reaction...only waiting for device is showing ? on my pc ...
Click to expand...
Click to collapse
Check if your USB cable is alright and appropriate drivers are installed. Otherwise reinstall drivers, restart your PC and try again.
alirazaagha said:
Check if your USB cable is alright and appropriate drivers are installed. Otherwise reinstall drivers, restart your PC and try again.
Click to expand...
Click to collapse
Bro we want to change any settings in device manager ...?
Ranji007 said:
Bro we want to change any settings in device manager ...?
Click to expand...
Click to collapse
No. Just update drivers.
alirazaagha said:
No. Just update drivers.
Click to expand...
Click to collapse
Bro when u take to service center they said for u motherboard problem or something??
Ranji007 said:
Bro when u take to service center they said for u motherboard problem or something??
Click to expand...
Click to collapse
Fortunately, I never took it there.
alirazaagha said:
Fortunately, I never took it there.
Click to expand...
Click to collapse
My phone was fallen in water then i changed the display..few days after it stopped working ..and when i take to serive centre they said to change motherboard..but it's the 80% of phone price...so iam here ?..iam trying thiz method
Ranji007 said:
My phone was fallen in water then i changed the display..few days after it stopped working ..and when i take to serive centre they said to change motherboard..but it's the 80% of phone price...so iam here ..iam trying thiz method
Click to expand...
Click to collapse
I think you might have damaged some hardware. But anyway if you want to use blankflash, I have a method.
In lenovo p2 we have another mode called QDloader mode, in which we can use blankflash. For entering into this mode, it's little tricky but, can enter in one or two go.
So, here's how:
1. Switch off the mobile.
2. Press the volume up key,
3. While holding the volume up key, insert the usb cable and at the same time press the power button (this is the trick, we have to insert and hit at the same time).
And voila! :highfive: you will see black screen with only red notification led blinking.
we are into QDloader mode. Now use blankflash :good: