Hey Friends,
You must have seen very good days with Lenovo P2 but when there comes a bad day when your phone stops responding to button holds and restarts. You may or may not have a clue what to do to get your phone working again just like before.
I got into this situation where only thing my phone was able to operate was a RED LED on connecting it to my laptop. Then I had to read tens of pages on XDA to find answers to all my questions. If you are in such a situation and your phone is UNLOCKED then you have come to the right place. Procedure is quite simple but remember, I am writing this guide to define complete process from blackout to complete update so follow this guide as per your needs.
I faced this situation of Total Blackout / Dead Phone (Almost) with only Red LED working and it can be very scary. So, here is the simplest procedure you can follow. I want to appreciate all those people who helped me in finding a way to boot my phone with each and everything working. Long story short, let's get this done.
Tools Required:
I am mentioning here all the Tools you will need. I will urge you to download and save these tools in case you want to unbrick your phone any time:
1. Minimal ADB and Fastboot setup for PC
2. Lenovo USB drivers v1.1.33
3. Qualcomm USB Drivers
4. Qualcomm Flash Image Loader (QFIL) v2.0.1.9 for your PC in case you have corrupted your phone's IMEI and/ or Baseband
5. Blankflash.bat in case you want to recover from total blackout (Attached)
6. Stock MM S048 Firmware for Lenovo P2 in case phone doesn't boot
7. S048_ModemTelephony.zip in case your phone boots through Stock MM S048 but SIM isn't detected and IMEI is missing. I have made a complete modem zip file for installation through recovery.
8. S251_ModemTelephony.zip in case your phone is on latest firmware and doesn't detect SIM and has lost IMEI. I have made a complete modem zip file for installation through recovery.
9. QCN file for recovering baseband version and giving you most precious network signals. (Attached)
10. WinRAR or PeaZip for uncompressing files
I will recommend you to have a specific folder for keeping all these tools in a single place.
Procedure for Unbricking:
Before going with the procedure, make sure you have downloaded all the files you need, updated Lenovo and Qualcomm drivers etc. Here is the procedure:
1. If total blackout with red LED notification when connecting to PC: Unzip blankflash.zip to a folder in C drive. Now connect your P2 to PC through USB, press volume+, volume- and power button simultaneously and double click blankflash.bat. You might have no success in your first try. Just keep trying and it will load your phone to Fastboot. Restart your phone in TWRP if installed and install a working ROM for your phone after doing a wipe. If all is good and phone works OK then great but if you have lost IMEI and baseband then it is better to reinstate your phone through first MM stock ROM S048
2. Install S048 firmware through Minimal ADB and Fastboot - use flash instructions in .txt file.
3. Wait for startup of phone. Check if fingerprint, BT, WIFI and SIM work if all work then OK.
4. If fingerprint, BT, WIFI and SIM are not working then check IMEI through dialer. Dial *#06#. If IMEI is not available then install latest TWRP through Fastboot.
5. Start P2 in TWRP recovery and install S048_ModemTelephony.zip. Restart phone to see if WIFI and SIM work.
6. If SIM is detected but not giving signals and Baseband is shown as unknown then extract 000000_0.qcn file given in .7z and restore through QFIL and restart your phone into Fastboot.
7. Now, install stock recovery of S048 firmware through Fastboot and restart your phone.
8. Use your phone like you normally do and update your P2 till firmware S251 and see if everything works including calls. Update your phone through OTA.
9. After OTA installation, stock recovery may say that update failed. Just press Back, go into Wipe user data menu and Wipe Cache only. Restart your phone which will be updated to latest version and will ask you to update to a newer version. Allow it to download the next update.
10. After installation of S251 update, install latest TWRP through Fastboot and install most recent version of LOS 16 so that your vendor partition is stable and free from any bloated files. Now, use your phone just like you want to.
If you need further clarification then ask in this thread.
Bro my phone is not unlocked can i try thz one
Ranji007 said:
Bro my phone is not unlocked can i try thz one
Click to expand...
Click to collapse
You should download S048 and use flashall.bat inside that archive to install it all. However, if you lose IMEI or baseband then you can use modem and qcn files given in this thread.
alirazaagha said:
You should download S048 and use flashall.bat inside that archive to install it all. However, if you lose IMEI or baseband then you can use modem and qcn files given in this thread.
Click to expand...
Click to collapse
Bro now i wanna use ...minimal adb ..my phone is totally bricked only red light glowing
Ranji007 said:
Bro now i wanna use ...minimal adb ..my phone is totally bricked only red light glowing
Click to expand...
Click to collapse
don't worry just flash blank flash from the link given in the op, you will get the bootloader back
hackiee said:
don't worry just flash blank flash from the link given in the op, you will get the bootloader back
Click to expand...
Click to collapse
Bro how to connect my phone to blank flash...can u PLZZ help
hackiee said:
don't worry just flash blank flash from the link given in the op, you will get the bootloader back
Click to expand...
Click to collapse
Laptop is not detecting my device bro i installed all lenovo and Qualcomm drivers...any idea
Ranji007 said:
Laptop is not detecting my device bro i installed all lenovo and Qualcomm drivers...any idea
Click to expand...
Click to collapse
If red light blinks, your phone can be detected by your laptop. Check ports in device manager settings and you'll see a new port with Qualcomm 9800 series number. If that's there, try blankflash to start in fastboot. It might need some tries before startup. Be patient and keep trying till you are in fastboot.
alirazaagha said:
If red light blinks, your phone can be detected by your laptop. Check ports in device manager settings and you'll see a new port with Qualcomm 9800 series number. If that's there, try blankflash to start in fastboot. It might need some tries before startup. Be patient and keep trying till you are in fastboot.
Click to expand...
Click to collapse
Bro ..thanks for reply....in my phone red blink is glowing continuously ..but after connecting there is no change...can u say which buttons i want to press?
Ranji007 said:
Bro ..thanks for reply....in my phone red blink is glowing continuously ..but after connecting there is no change...can u say which buttons i want to press?
Click to expand...
Click to collapse
Press Volume+, Volume- and Power simultaneously and double click flashblank.bat. It might take some tries to finally install the scripts and start phone in fastboot. It took me 20+ tries to finally detect my phone through blankflash. Please, read OP completely.
alirazaagha said:
Press Volume+, Volume- and Power simultaneously and double click flashblank.bat. It might take some tries to finally install the scripts and start phone in fastboot. It took me 20+ tries to finally detect my phone through blankflash. Please, read OP completely.
Click to expand...
Click to collapse
Bro we want to connect each time removing usb cable and connect again like that ..we wanna do 20 times??
Ranji007 said:
Bro we want to connect each time removing usb cable and connect again like that ..we wanna do 20 times??
Click to expand...
Click to collapse
No. Keep USB connected. Try blankflash. If it doesn't detect phone or go ahead. Close command terminal, double click again and keep doing it till it processes the files. If it is stuck somewhere. Close terminal and try again.
alirazaagha said:
No. Keep USB connected. Try blankflash. If it doesn't detect phone or go ahead. Close command terminal, double click again and keep doing it till it processes the files. If it is stuck somewhere. Close terminal and try again.
Click to expand...
Click to collapse
Bro is there any solution ..i continuously pressed volume and power buttons connected to laptop and opening blank flash continuously for number of times ...but there was no reaction...only waiting for device is showing ? on my pc ...
Ranji007 said:
Bro is there any solution ..i continuously pressed volume and power buttons connected to laptop and opening blank flash continuously for number of times ...but there was no reaction...only waiting for device is showing ? on my pc ...
Click to expand...
Click to collapse
Check if your USB cable is alright and appropriate drivers are installed. Otherwise reinstall drivers, restart your PC and try again.
alirazaagha said:
Check if your USB cable is alright and appropriate drivers are installed. Otherwise reinstall drivers, restart your PC and try again.
Click to expand...
Click to collapse
Bro we want to change any settings in device manager ...?
Ranji007 said:
Bro we want to change any settings in device manager ...?
Click to expand...
Click to collapse
No. Just update drivers.
alirazaagha said:
No. Just update drivers.
Click to expand...
Click to collapse
Bro when u take to service center they said for u motherboard problem or something??
Ranji007 said:
Bro when u take to service center they said for u motherboard problem or something??
Click to expand...
Click to collapse
Fortunately, I never took it there.
alirazaagha said:
Fortunately, I never took it there.
Click to expand...
Click to collapse
My phone was fallen in water then i changed the display..few days after it stopped working ..and when i take to serive centre they said to change motherboard..but it's the 80% of phone price...so iam here ?..iam trying thiz method
Ranji007 said:
My phone was fallen in water then i changed the display..few days after it stopped working ..and when i take to serive centre they said to change motherboard..but it's the 80% of phone price...so iam here ..iam trying thiz method
Click to expand...
Click to collapse
I think you might have damaged some hardware. But anyway if you want to use blankflash, I have a method.
In lenovo p2 we have another mode called QDloader mode, in which we can use blankflash. For entering into this mode, it's little tricky but, can enter in one or two go.
So, here's how:
1. Switch off the mobile.
2. Press the volume up key,
3. While holding the volume up key, insert the usb cable and at the same time press the power button (this is the trick, we have to insert and hit at the same time).
And voila! :highfive: you will see black screen with only red notification led blinking.
we are into QDloader mode. Now use blankflash :good:
Related
I have tried several things mentioned on this forum but to know avail. My LG Optimus 3d P920 isnt coming up after i flashed the rom. When i connect to the system on window 7, it shows omap under unknown driver and withing 2secs disappears again. using one of the methods mentioned here, i was able to install the omap driver but each time i connect the phone, it connects and then disconnect instantly. When i tried it on window xp, i got the same error. I can boot into recovery. The phone is not switching ON atall for me to even consider goin to recovery. Sometimes when am on window xp and i press the recovery button with the battery in (vol- plus Power +3d button) it connects and then instantly disconnects again. Please help with a step by step process as am stumped. Am sure i should be able to get it up. Any help will be greatly appreciated
drwale2000 said:
I have tried several things mentioned on this forum but to know avail. My LG Optimus 3d P920 isnt coming up after i flashed the rom. When i connect to the system on window 7, it shows omap under unknown driver and withing 2secs disappears again. using one of the methods mentioned here, i was able to install the omap driver but each time i connect the phone, it connects and then disconnect instantly. When i tried it on window xp, i got the same error. I can boot into recovery. The phone is not switching ON atall for me to even consider goin to recovery. Sometimes when am on window xp and i press the recovery button with the battery in (vol- plus Power +3d button) it connects and then instantly disconnects again. Please help with a step by step process as am stumped. Am sure i should be able to get it up. Any help will be greatly appreciated
Click to expand...
Click to collapse
It's very simple,you must follow this guide if you want GB http://www.xda-developers.com/android/downgrade-the-lg-optimus-3d-to-gingerbread/ or this guide if you want ICS http://www.google.it/url?sa=t&rct=j...2ICoDA&usg=AFQjCNE1Gq5ak_HIJAFcWnsfgrxK6mf9UQ
Enjoy ^^
Still not clear
Darek96 said:
It's very simple,you must follow this guide if you want GB http://www.xda-developers.com/android/downgrade-the-lg-optimus-3d-to-gingerbread/ or this guide if you want ICS http://www.google.it/url?sa=t&rct=j...2ICoDA&usg=AFQjCNE1Gq5ak_HIJAFcWnsfgrxK6mf9UQ
Enjoy ^^
Click to expand...
Click to collapse
Thanks a bunch for your reply, the sad thing is both explanation arent clear enough. Am sorry to bother you but can i get like an idiot guide as both links especially the one with ics isnt really clear enough and the downgrade isnt helping either. downloaded their files yetdont know hw or what to do with em. Please help
Preferrably i will like a guide with downgrading. The links sent has no step by step method,it naturally assumes that one will know what to do with what file. Waiting for ur response.
Thanks again
drwale2000 said:
I have tried several things mentioned on this forum but to know avail. My LG Optimus 3d P920 isnt coming up after i flashed the rom. When i connect to the system on window 7, it shows omap under unknown driver and withing 2secs disappears again. using one of the methods mentioned here, i was able to install the omap driver but each time i connect the phone, it connects and then disconnect instantly. When i tried it on window xp, i got the same error. I can boot into recovery. The phone is not switching ON atall for me to even consider goin to recovery. Sometimes when am on window xp and i press the recovery button with the battery in (vol- plus Power +3d button) it connects and then instantly disconnects again. Please help with a step by step process as am stumped. Am sure i should be able to get it up. Any help will be greatly appreciated
Click to expand...
Click to collapse
Hi,
study carefully and follow step by step
http://forum.xda-developers.com/showthread.php?t=1942836
You will be up and running!!
please click the thanks button if you think I helped
schubeir
Still Stump
schubeir said:
Hi,
study carefully and follow step by step
http://forum.xda-developers.com/showthread.php?t=1942836
You will be up and running!!
please click the thanks button if you think I helped
schubeir
Click to expand...
Click to collapse
I have tried the method you explained step by step bt i got stuckedd on step 13
"Step 13. Run Steps 3-9 again and you will see your phone being flashed from LG FlashTool.
It will be stopped at 26-30% because phone will turn off on its own BUT the next time you try to enter NORMAL DOWNLOAD MODE it will be available again."
When i do what step 12 says, instead of my LG flash tool flashin my fone, the screeen just stay stuck on the download mode with the korean message on it. Dont know how to move ahead. Thanks for your reply, please help me move past this level. In addition, instead of LGE mobile USB serial port, what i have is LGE CDMA USB serial port.
Am still stumped
drwale2000 said:
I have tried the method you explained step by step bt i got stuckedd on step 13
"Step 13. Run Steps 3-9 again and you will see your phone being flashed from LG FlashTool.
It will be stopped at 26-30% because phone will turn off on its own BUT the next time you try to enter NORMAL DOWNLOAD MODE it will be available again."
When i do what step 12 says, instead of my LG flash tool flashin my fone, the screeen just stay stuck on the download mode with the korean message on it. Dont know how to move ahead. Thanks for your reply, please help me move past this level. In addition, instead of LGE mobile USB serial port, what i have is LGE CDMA USB serial port.
Click to expand...
Click to collapse
Somebody pls help me, i am able to get into the download mode but cant get beyond that stage. I have tried LG flashtool several time to get it fixed bt LG Flashtool is discovering my phone. Even when i click start though its suppose to start automatically, it just doesnt do anything. Or could it be because under my device manager i have LGE CDMA USB serial port instead of LGE mobile USD serial port ? because its my LGE CDMA USB serial port that i turned its port to 41
I need help please
drwale2000 said:
Somebody pls help me, i am able to get into the download mode but cant get beyond that stage. I have tried LG flashtool several time to get it fixed bt LG Flashtool is discovering my phone. Even when i click start though its suppose to start automatically, it just doesnt do anything. Or could it be because under my device manager i have LGE CDMA USB serial port instead of LGE mobile USD serial port ? because its my LGE CDMA USB serial port that i turned its port to 41
I need help please
Click to expand...
Click to collapse
you are absolutely right, that guide of how to flash ICS ported is not so clear enough for noob like us to fallow.
Fallow this guide. i hope it will help you, because it has saved my but for many times. i hope it will do the same for you.
http://www.technopat.net/forum/andr...lg-optimus-3d-ultimate-flash-guide-print.html
drwale2000 said:
Thanks a bunch for your reply, the sad thing is both explanation arent clear enough. Am sorry to bother you but can i get like an idiot guide as both links especially the one with ics isnt really clear enough and the downgrade isnt helping either. downloaded their files yetdont know hw or what to do with em. Please help
Preferrably i will like a guide with downgrading. The links sent has no step by step method,it naturally assumes that one will know what to do with what file. Waiting for ur response.
Thanks again
Click to expand...
Click to collapse
Okay,i will write a small guide
1-Download all the files in the downgrading package
2-Install LG FlashTool
3-Go on the FlashTool directory and change the standard icon with the modified one in the folder
4-Now install all the drivers in the package,if the install fail,uninstall all the lg drivers and do the procedure again
5-Now keep pressing volume UP and connect your phone to the computer
6-On the computer press start and search device manager
7-Open it and search COM Ports and change the LGE etc.. Port to COM41
8-Now you are done to do the procedure,so open LG FlashTool as administrator
9-Will appear a window with the files to put in,select BOOT21E.CP and BOOT21.AP,and select USB Mode
10-Now press ok and connect the phone to your pc pressing Volume UP
11-Go on the icon of ports(looks like a usb port) and select only port 1
12-Now press Start(the yellow arrow)
13-Now disconnect your phone and connect it,without pressing any button
14-The downgrade procedure will start automatically,so keep calm and...Enjoy!
progress but not complete
Darek96 said:
Okay,i will write a small guide
1-Download all the files in the downgrading package
2-Install LG FlashTool
3-Go on the FlashTool directory and change the standard icon with the modified one in the folder
4-Now install all the drivers in the package,if the install fail,uninstall all the lg drivers and do the procedure again
5-Now keep pressing volume UP and connect your phone to the computer
6-On the computer press start and search device manager
7-Open it and search COM Ports and change the LGE etc.. Port to COM41
8-Now you are done to do the procedure,so open LG FlashTool as administrator
9-Will appear a window with the files to put in,select BOOT21E.CP and BOOT21.AP,and select USB Mode
10-Now press ok and connect the phone to your pc pressing Volume UP
11-Go on the icon of ports(looks like a usb port) and select only port 1
12-Now press Start(the yellow arrow)
13-Now disconnect your phone and connect it,without pressing any button
14-The downgrade procedure will start automatically,so keep calm and...Enjoy!
Click to expand...
Click to collapse
Thanks a bunch, i have finally gotten a lil hang of it. The problem now is each time i flash with LG flash tool, once it gets to 82%, the part where the flashtool reads target resetting , my fone disconnects and the LG flashtool brings out this error error_wm_progress_msg and some others. I have tried this 3times now and the error remains the same. When i power the phone, it goes in to clockwod mode and when i try to mount usb, it doesnt do. Even when i try to restore the backup i have, it says md5 error. Waiting for your reply
drwale2000 said:
Thanks a bunch, i have finally gotten a lil hang of it. The problem now is each time i flash with LG flash tool, once it gets to 82%, the part where the flashtool reads target resetting , my fone disconnects and the LG flashtool brings out this error error_wm_progress_msg and some others. I have tried this 3times now and the error remains the same. When i power the phone, it goes in to clockwod mode and when i try to mount usb, it doesnt do. Even when i try to restore the backup i have, it says md5 error. Waiting for your reply
Click to expand...
Click to collapse
That s mean your phone is successfully done flashing , with me it never come to 100% it always on 82% its finish, just reboot your phone and wait for it to start on , and you are good to go, now go to recovery and format, or wipe cache and data and reboot at first time it says that you don't have enough memory left just go to privacy and reset the phone and format everything . and i think everything will be good after that. good luck.
Thanks
:good:
bensmokie said:
That s mean your phone is successfully done flashing , with me it never come to 100% it always on 82% its finish, just reboot your phone and wait for it to start on , and you are good to go, now go to recovery and format, or wipe cache and data and reboot at first time it says that you don't have enough memory left just go to privacy and reset the phone and format everything . and i think everything will be good after that. good luck.
Click to expand...
Click to collapse
Was just bout to tell u its now working. Thanks a million. U saved me buying another phone. By the way i want to flash the new jellybam on it.Any help how to go about it cus the last time i tried, the jellybam keeps hanging, or automatically shutdown. I have to remove the battery to start it again.
Thanks
drwale2000 said:
:good:
Was just bout to tell u its now working. Thanks a million. U saved me buying another phone. By the way i want to flash the new jellybam on it.Any help how to go about it cus the last time i tried, the jellybam keeps hanging, or automatically shutdown. I have to remove the battery to start it again.
Thanks
Click to expand...
Click to collapse
The truth is your phone can not be break just with flashing, it will brick though, unless your hardware is damaged, then you are think to buy new phone.
well about the JellyBam, while you are on GB now, root your phone and install Rom manager flash Bernie's file and you're out of the rebooting. the Barnie's files is the key of JellyBam or other CM10 to work. good luck.
Thanks
bensmokie said:
The truth is your phone can not be break just with flashing, it will brick though, unless your hardware is damaged, then you are think to buy new phone.
well about the JellyBam, while you are on GB now, root your phone and install Rom manager flash Bernie's file and you're out of the rebooting. the Barnie's files is the key of JellyBam or other CM10 to work. good luck.
Click to expand...
Click to collapse
Thanks for the prompt reply, i just noticed that my phone isnt detecting my sim card. Its not showing any network, i just finished installing 3d kongdom rom on it but its not showing network signal. Any help on how to fix that then can u point me to a page where i can follow the instruction of how to install the jellybam cus ijust did and its still giving the same error i mentioned earlier. I luv the interface but importantly, i will love to have network signal back on my fone
drwale2000 said:
Thanks for the prompt reply, i just noticed that my phone isnt detecting my sim card. Its not showing any network, i just finished installing 3d kongdom rom on it but its not showing network signal. Any help on how to fix that then can u point me to a page where i can follow the instruction of how to install the jellybam cus ijust did and its still giving the same error i mentioned earlier. I luv the interface but importantly, i will love to have network signal back on my fone
Click to expand...
Click to collapse
fallow this one it work for JellyBam too. http://forum.xda-developers.com/showthread.php?t=2083013
but don't forget to flash berni's files ,here : http://forum.xda-developers.com/showthread.php?p=35199371]
because if not you will not have the network signal again and it will keep rebooting.
but if i could suggest you Just suggestion . you to flash ICS first to see how is it. i love CM10 too and smoothness of it you can't resist, but it has lotta bugs for now so to avoid all that you should starting using the ICS ported by Xbsall, it work very fine.
U are a life saver
bensmokie said:
fallow this one it work for JellyBam too. http://forum.xda-developers.com/showthread.php?t=2083013
but don't forget to flash berni's files ,here : http://forum.xda-developers.com/showthread.php?p=35199371]
because if not you will not have the network signal again and it will keep rebooting.
but if i could suggest you Just suggestion . you to flash ICS first to see how is it. i love CM10 too and smoothness of it you can't resist, but it has lotta bugs for now so to avoid all that you should starting using the ICS ported by Xbsall, it work very fine.
Click to expand...
Click to collapse
Thanks again for the response. I am goin to have to go with ur advise, Please send me a link to ics rom wit a guide,if possible help me right it out step by step cus the one u did earlier was just amazing. I shall install ICs. please send me the links.
Thanks
drwale2000 said:
Thanks again for the response. I am goin to have to go with ur advise, Please send me a link to ics rom wit a guide,if possible help me right it out step by step cus the one u did earlier was just amazing. I shall install ICs. please send me the links.
Thanks
Click to expand...
Click to collapse
First of all you will need this here: http://www.technopat.net/forum/andr...lg-optimus-3d-ultimate-flash-guide-print.html
Download the ICS ported ,thank you Xbsall for this awesome job, without you, none will have ICS running to their device p920.
download only ROM file XBSA404.rar. here: http://forum.xda-developers.com/showthread.php?t=1956347
once you download it, the extract it in one new folder on ur desktop that way it will easy to find .
Well Start Lg flash tool, and flash both file as you did before , i mean in this way: http://www.technopat.net/forum/andr...lg-optimus-3d-ultimate-flash-guide-print.html
once done you are on ICS.
Root it this way: http://forum.xda-developers.com/showthread.php?t=1905116
Or this way : http://forum.xda-developers.com/showpost.php?p=31963526&postcount=532
they both work for me.
once u done that you need to flash twrp or Cwm.
you in here. http://forum.xda-developers.com/showthread.php?t=1978543
Then you can flash this if you want : http://forum.xda-developers.com/showthread.php?t=1963847
i wish you good luck!
those are the guide that i used, and they did really god job for me, hope they will do the same for you!:good:
I cant download root software
bensmokie said:
First of all you will need this here: http://www.technopat.net/forum/andr...lg-optimus-3d-ultimate-flash-guide-print.html
Download the ICS ported ,thank you Xbsall for this awesome job, without you, none will have ICS running to their device p920.
download only ROM file XBSA404.rar. here: http://forum.xda-developers.com/showthread.php?t=1956347
once you download it, the extract it in one new folder on ur desktop that way it will easy to find .
Well Start Lg flash tool, and flash both file as you did before , i mean in this way: http://www.technopat.net/forum/andr...lg-optimus-3d-ultimate-flash-guide-print.html
once done you are on ICS.
Root it this way: http://forum.xda-developers.com/showthread.php?t=1905116
Or this way : http://forum.xda-developers.com/showpost.php?p=31963526&postcount=532
they both work for me.
once u done that you need to flash twrp or Cwm.
you in here. http://forum.xda-developers.com/showthread.php?t=1978543
Then you can flash this if you want : http://forum.xda-developers.com/showthread.php?t=1963847
i wish you good luck!
those are the guide that i used, and they did really god job for me, hope they will do the same for you!:good:
Click to expand...
Click to collapse
Tanks buddy for all your help. I now have ICS on my phone but its not rooted yet. I tried downloading from one of the links you sent me but the file wasnt there anymore.After reading all comment, i found a page but the problem is my system has been having difficulties downloading from upload.com Its been an issue a very long time ago.Both my systems. Could you help me with a different link pls so i can root it. In additon, my back button is acting like cancel button,instead of taking me back, it takes me home, howcan i fix that
drwale2000 said:
Tanks buddy for all your help. I now have ICS on my phone but its not rooted yet. I tried downloading from one of the links you sent me but the file wasnt there anymore.After reading all comment, i found a page but the problem is my system has been having difficulties downloading from upload.com Its been an issue a very long time ago.Both my systems. Could you help me with a different link pls so i can root it. In additon, my back button is acting like cancel button,instead of taking me back, it takes me home, howcan i fix that
Click to expand...
Click to collapse
Guy,in the ICS OS of LG Optimus 3D,the search button acts as back button and the back button acts as home button,and the camera is upside-down..you can fix only the camera,search on forum,there are many guides
Thanks darek
Darek96 said:
Guy,in the ICS OS of LG Optimus 3D,the search button acts as back button and the back button acts as home button,and the camera is upside-down..you can fix only the camera,search on forum,there are many guides
Click to expand...
Click to collapse
Thanks darek for the info, i found out some hours ago too. Its a pain in the bud. I dont mind the camera bt the search and back button i do mind. Is there a way to go bout that, if not is there any other ics rom that i can try because i doubt i can use this. Pls reply asap
drwale2000 said:
Thanks darek for the info, i found out some hours ago too. Its a pain in the bud. I dont mind the camera bt the search and back button i do mind. Is there a way to go bout that, if not is there any other ics rom that i can try because i doubt i can use this. Pls reply asap
Click to expand...
Click to collapse
For the question of buttons,is only a habit question
No one rom with ICS can solve this problem,so accept it xD
Hello guys..
Karbonn A12+ is newly launched Android phone with 1.3GHz processor and 512MB RAM...Still we didn't have Stock ROM for this model...
Now i proudly present Stock jellybean ROM for Karbonn A12+..
I prepared it to flash via SP Flash Tool..
Now don't worry to experiment with your Mobile do experiment and you can recover your karbonn A12+...
So keep learning and Do some intresting experiment and make some custom ROM...
NOTE:- Flashing Process and these type of development process may cause any unwanted and unknown errors...So please Try it at your OWN RISK...I will not Responsible for any damge...
now here are is method to flash.
(Try At Your OWN RISK...)
you Need.
1.An PC (Ofcorse you need and PC or laptop)
2. Karbonn A12+ Stock jellybean ROM (Download)
3. SP_Flash_Tool v3.1312.0.139 (other Version may not work proper)(NOTE:- Flashing Process and these type of development process may cause any unwanted and unknown errors...So please Try it at your OWN RISK...I will not Responsible for any damge...[/COLOR][/B]
Download Links:-
[url]http://a2zandroidrom.blogspot.in/2014/09/karbonn-a12-stock-jellybean-rom.html
Drivers are added...
links are
http://a2zandroidrom.blogspot.in/2014/09/karbonn-a12-stock-jellybean-rom.html
Download file is password protected..password is given in download link page...Download is available in small parts as well as in single part also...
post your review please !!
Good work Bro . . .
suthar88.sunil said:
Good work Bro . . .
Click to expand...
Click to collapse
Thanks
Phone not connecting
greatpapa said:
Hello guys..
Karbonn A12+ is newly launched Android phone with 1.3GHz processor and 512MB RAM...Still we didn't have Stock ROM for this model...
Now i proudly present Stock jellybean ROM for Karbonn A12+..
I prepared it to flash via SP Flash Tool..
Now don't worry to experiment with your Mobile do experiment and you can recover your karbonn A12+...
So keep learning and Do some intresting experiment and make some custom ROM...
NOTE:- Flashing Process and these type of development process may cause any unwanted and unknown errors...So please Try it at your OWN RISK...I will not Responsible for any damge...
now here are is method to flash.
(Try At Your OWN RISK...)
you Need.
1.An PC (Ofcorse you need and PC or laptop)
2. Karbonn A12+ Stock jellybean ROM
3. SP_Flash_Tool v3.1312.0.139 (other Version may not work proper)
Method
1. Download all files on your PC and extract them on one place.
2. now you will have two folder name by "!Files_to_FlashTool" and "SP_Flash_Tool_v3.1312.0.139"
3. Now RUN SP flash Tool.
4. now click on "scatter-loading" tab.
5. now Select "scatter file"....Sp tool will list up all the component to flash.
6.now hit the Download button on SP...you will see an warning something like user data and cache are not loaded or something...just ignore it...and click on "Yes".and now you are ready to flash.
7. Now switchoff your phone (If it is on) and pull out the battery.
8. Connect your phone while battery is out.
9.After connecting your Phone insert your battery...
10. Sp Tool will recognise your Phone and flashing will start.
11. Green circle will show that flash is Done...
Enjoy
NOTE:- Flashing Process and these type of development process may cause any unwanted and unknown errors...So please Try it at your OWN RISK...I will not Responsible for any damge...
Download file is password protected..password is given in download link page...Download is available in small parts as well as in single part also...
post your review please !!
Click to expand...
Click to collapse
My phone is not connecting. i tried many times. help me out plzzz..
Combination
vikphogat said:
My phone is not connecting. i tried many times. help me out plzzz..
Click to expand...
Click to collapse
First of all your have to install VCOM USB drivers for MTK6572 devices....
And then after hitting download button connect your phone while pressing both volume down + up button together....or try this type of different combination....
yes this is most difficult part..i tried 20 times myself....
if not working then try on different machine
As you will be connected there will be an Red and yellow line on SP tool
Next to try..
after hitting download button Press power and volume up button and then connect USB cable while pressing those key together....
Even you can try this new flash tool
http://www.mediafire.com/download/tnas2hjqruf2iht/SP_Flash_Tool_v5.1343.01_by_indiantitaniclover.zip
thanks dude..!!
greatpapa said:
First of all your have to install VCOM USB drivers for MTK6572 devices....
And then after hitting download button connect your phone while pressing both volume down + up button together....or try this type of different combination....
yes this is most difficult part..i tried 20 times myself....
if not working then try on different machine
As you will be connected there will be an Red and yellow line on SP tool
Next to try..
after hitting download button Press power and volume up button and then connect USB cable while pressing those key together....
Even you can try this new flash tool
Click to expand...
Click to collapse
i will try it surely.. can u please also provide me the link to vcom usb drivers for karbonn a12+ ?
thanks in advance.. :laugh::good:
Dri
vikphogat said:
i will try it surely.. can u please also provide me the link to vcom usb drivers for karbonn a12+ ?
thanks in advance.. :laugh::good:
Click to expand...
Click to collapse
New flashtool will recognise direct....Hope so...download new flash tool and try...
greatpapa said:
New flashtool will recognise direct....Hope so...download new flash tool and try...
Click to expand...
Click to collapse
i have tried it nearly 15 16 times. but when i put battery presing and holding volume up + down button phone goes to factory mode. 8 options written in chinese are showing up.
Powrer
vikphogat said:
i have tried it nearly 15 16 times. but when i put battery presing and holding volume up + down button phone goes to factory mode. 8 options written in chinese are showing up.
Click to expand...
Click to collapse
First click on download in flashtool...then press
power + volume up and connect while pressing...Working for me..tested by myself...
hard bricker karbonn a12+........
Great work and nice tutorial some how unbricked my phone 100% working
\\beginers dont post any spam without reading the complete tutorial as I did
thanks a lot for helping
not working
greatpapa said:
First click on download in flashtool...then press
power + volume up and connect while pressing...Working for me..tested by myself...
Click to expand...
Click to collapse
plz help it's not working.installed usb driver & latest sp flash tool.still not working ????
Fastboot
Lovesahota said:
plz help it's not working.installed usb driver & latest sp flash tool.still not working ????
Click to expand...
Click to collapse
Hello....
Try this one..
Switch off your mobile...
Now press volume up + Power button...
Then you will see three option something like Recovery, fastboot, factory...
You have to choose fastboot option...
when fastboot is selected then connect your phone to PC via USB cable...this will install some helpful drivers to your PC....and then again try the flash method without battery...
Stuck at the EYE boot screen of Karbonn A12+. Any help please? Yes, I followed the instructions carefully.
http://playrangers.com/KarbonnA12plus/
in that page the usb drivers of 6577 is provided. Kindly provice MT6572 VCOM drivers.
Process DOne ?
nightcrawler218 said:
Stuck at the EYE boot screen of Karbonn A12+. Any help please? Yes, I followed the instructions carefully.
http://playrangers.com/KarbonnA12plus/
in that page the usb drivers of 6577 is provided. Kindly provice MT6572 VCOM drivers.
Click to expand...
Click to collapse
Did you flashed in proper way ?
means your Sptool recognise your mobile and did you see red and yellow line in sptool and was process done or not ?
greatpapa said:
Did you flashed in proper way ?
means your Sptool recognise your mobile and did you see red and yellow line in sptool and was process done or not ?
Click to expand...
Click to collapse
yeah, everything was according to the tutorial. phone was detected, first red, then blue then yellow progress bar & finally green circle. I removed the usb & reinserted the battery after flashing then pressed the power button. Karbonn animation shown & stuck at the eye screen. After a number of failed attempts I decied to erase the whole device & then flash again. I erased flash+bootloader. The phone is dead now. not powering up. But if I connect the phone via usb to pc a beep sound is heard. Any clue, how to restore the bootloader?
How
nightcrawler218 said:
yeah, everything was according to the tutorial. phone was detected, first red, then blue then yellow progress bar & finally green circle. I removed the usb & reinserted the battery after flashing then pressed the power button. Karbonn animation shown & stuck at the eye screen. After a number of failed attempts I decied to erase the whole device & then flash again. I erased flash+bootloader. The phone is dead now. not powering up. But if I connect the phone via usb to pc a beep sound is heard. Any clue, how to restore the bootloader?
Click to expand...
Click to collapse
How did you erase the Bootloader....??
if you have deleted your bootloader then it would be diffecult to revive the phone
greatpapa said:
How did you erase the Bootloader....??
if you have deleted your bootloader then it would be diffecult to revive the phone
Click to expand...
Click to collapse
I Used SP flash tool to format the device. There was an option for erasing everything (Flash + bootloader).
Will the service center accept my case.?
Ummm
nightcrawler218 said:
I Used SP flash tool to format the device. There was an option for erasing everything (Flash + bootloader).
Will the service center accept my case.?
Click to expand...
Click to collapse
Try again whole method...if you are hearing an beep sound....
Does your mobile is going in recovery mode or fastboot mode ?
Power + volume up (battery is inserted)
greatpapa said:
Try again whole method...if you are hearing an beep sound....
Does your mobile is going in recovery mode or fastboot mode ?
Power + volume up (battery is inserted)
Click to expand...
Click to collapse
Thanks a million times man for your suggestion.
I tried with fastboot but no device shown. I went to device manager & uninstalled-then reinstalled the drivers. That actually helped me to build the serial communication between SP flash tool & Device.
Then I discarded the battery & retried the SP flash tool, this time the phone is finally detected & flashed successfully. red, blue, yellow bar then green circle. DONE.
Now, the same issue. Karbonn boot animation is displayed & stuck at the eye screen. I have covered the halfway but cant be able to get success in the other half (cant see the homescreen or anything.)
---------- Post added at 09:15 PM ---------- Previous post was at 09:07 PM ----------
Phone is OK now but it says INVALID IMEI... any suggestions please...
Good
nightcrawler218 said:
Thanks a million times man for your suggestion.
I tried with fastboot but no device shown. I went to device manager & uninstalled-then reinstalled the drivers. That actually helped me to build the serial communication between SP flash tool & Device.
Then I discarded the battery & retried the SP flash tool, this time the phone is finally detected & flashed successfully. red, blue, yellow bar then green circle. DONE.
Now, the same issue. Karbonn boot animation is displayed & stuck at the eye screen. I have covered the halfway but cant be able to get success in the other half (cant see the homescreen or anything.)
---------- Post added at 09:15 PM ---------- Previous post was at 09:07 PM ----------
Phone is OK now but it says INVALID IMEI... any suggestions please...
Click to expand...
Click to collapse
Don't worry....
Now your phone will be fine....As i will get time i will give you tutorial to write your IMEI number....Till then you can search and google it....your phone is ok...will recover it soon....
Hello everyone I have a few questions. First to say that I'm not new to android yet I don't think I'm very advanced. Anyway here is my situation: I have brand new chinese phone Cubot x6 which is with MT6592 chipset(or CPU I'm not sure). I rooted the device with Framaroot and everything was OK. Then I found CWM for the device on needrom(dot)com and when I flashed the recovery with "Flashify" it rebooteed but it is now stuck on the kernel logo. I can enter only in recovery which is still the stock one . I can't do anything except entering into the stock recovery. I have the stock ROM but it is NOT in a flashable .zip but in a folder which is used by some flashtool program (not the one for Sony but rather for MT devices) I have the stock boot.img, recovery.img and system.img. When I try to "apply update from sideload" and sideload either the boot or recovery images I get "installation aborted". If you guys can tell me how to enter fastboot mode and from there to flash system.img OR any other way to fix the phone please tell me.
P.S. The hardware buttons are only volume rockers and power button. I also tried to install MUIU but it can't flash it with stock recovery.
Please help me. I would be able to manage it somehow if I'm able to use adb, but I can't within the stock recovery.
hello dont problem use sp flashtool and flash rom stock
http://www.needrom.com/mobile/cubot-x6/
ROM
http://www.needrom.com/wp-content/uploads/2014/05/G807_C1_D1_CUBOT_V0.9.rar
SP FLASH TOOL
http://www.needrom.com/wp-content/uploads/2014/01/SP_Flash_Tool_v5.1348.00.zip
Description
ROM Mobile Cubot X6 – ROM Android 4.2.2
ONLY MT6592
Official ROM Cubot X6 Version: G807_C1_D1_CUBOT_V0.9
Gapps include – No Rooted
Language support: Multilang
Install ROM:
- Unpack FlashTools, and Click on Flash_tool.exe
- Select a the MT6592_Android_scatter_emmc.txt in ROM
- Wait file to be added into Flash Tool
- choose Option->USB Model,click USB Model
–> Choose Option->DA DownLoad All->Speed->High Speed, click High Speed
- Turn off your phone, remove the battery.
- "Press F9 (hit Download button)" OR " if upgrade ROM Firmware->Upgrade "
- and connect your phone into the computer via USB data cable.
- The process will start and a red progress bar will appear after color purple, yellow.
- And green circles display
- Finish !
- You can now safely disconnect your phone and turn it on.
Would it be possible for you to upload it to a different site? it seems that the download just cuts off all the time. I tried about 5 times after 10 mins it just stops. I bricked my phone the first day cuz i didnt know it wasnt compatible with Xposed installer
ZALACAYN2 said:
hello dont problem use sp flashtool and flash rom stock
http://www.needrom.com/mobile/cubot-x6/
ROM
http://www.needrom.com/wp-content/uploads/2014/05/G807_C1_D1_CUBOT_V0.9.rar
SP FLASH TOOL
http://www.needrom.com/wp-content/uploads/2014/01/SP_Flash_Tool_v5.1348.00.zip
Description
ROM Mobile Cubot X6 – ROM Android 4.2.2
ONLY MT6592
Official ROM Cubot X6 Version: G807_C1_D1_CUBOT_V0.9
Gapps include – No Rooted
Language support: Multilang
Install ROM:
- Unpack FlashTools, and Click on Flash_tool.exe
- Select a the MT6592_Android_scatter_emmc.txt in ROM
- Wait file to be added into Flash Tool
- choose Option->USB Model,click USB Model
–> Choose Option->DA DownLoad All->Speed->High Speed, click High Speed
- Turn off your phone, remove the battery.
- "Press F9 (hit Download button)" OR " if upgrade ROM Firmware->Upgrade "
- and connect your phone into the computer via USB data cable.
- The process will start and a red progress bar will appear after color purple, yellow.
- And green circles display
- Finish !
- You can now safely disconnect your phone and turn it on.
Click to expand...
Click to collapse
http://pan.baidu.com/s/1jGn3mvk
Enviado desde mi CUBOT X6 mediante Tapatalk
Thank you very much
ZALACAYN2 said:
http://pan.baidu.com/s/1jGn3mvk
Enviado desde mi CUBOT X6 mediante Tapatalk
Click to expand...
Click to collapse
I know this is an old thread, but please understand that I'm following this and I need help as I have the same phone and I haven't found any other updated threads on this topic.
ZALACAYN2 said:
Install ROM:
- Unpack FlashTools, and Click on Flash_tool.exe
- Select a the MT6592_Android_scatter_emmc.txt in ROM
- Wait file to be added into Flash Tool
- choose Option->USB Model,click USB Model
–> Choose Option->DA DownLoad All->Speed->High Speed, click High Speed
- Turn off your phone, remove the battery.
- "Press F9 (hit Download button)" OR " if upgrade ROM Firmware->Upgrade "
- and connect your phone into the computer via USB data cable.
- The process will start and a red progress bar will appear after color purple, yellow.
- And green circles display
- Finish !
- You can now safely disconnect your phone and turn it on.
Click to expand...
Click to collapse
I'm following this, as I tried to do this before, I was apparently doing something wrong and I couldn't get to the part where the program would actually flash it and it never showed progress bars or even detected the phone, now finally my phone is recognized by the program and it's now stuck on the red progress bar, when I put my mouse over it says "Download DA Now..." ?? what is it?
Should I do something, I don't wanna stop it with fear it may brick completely...
7 mins has passed, do I leave it there? I just saw the red progress bar going up to 100% and stay there... Nothing more, purple, or yellow :crying:
Does it usually takes that much? Another thing is that I don't see the device (usb) showing up in the Device Manager... is something going on? the sp flash tool might have become stuck on it doing nothing, but like I said, I dont wanna stop it with fear it might be actually doing something, and then I break it :S
@0xNOP nop,it doesnt take that long
0xNOP said:
I know this is an old thread, but please understand that I'm following this and I need help as I have the same phone and I haven't found any other updated threads on this topic.
I'm following this, as I tried to do this before, I was apparently doing something wrong and I couldn't get to the part where the program would actually flash it and it never showed progress bars or even detected the phone, now finally my phone is recognized by the program and it's now stuck on the red progress bar, when I put my mouse over it says "Download DA Now..." ?? what is it?
Should I do something, I don't wanna stop it with fear it may brick completely...
7 mins has passed, do I leave it there? I just saw the red progress bar going up to 100% and stay there... Nothing more, purple, or yellow :crying:
Does it usually takes that much? Another thing is that I don't see the device (usb) showing up in the Device Manager... is something going on? the sp flash tool might have become stuck on it doing nothing, but like I said, I dont wanna stop it with fear it might be actually doing something, and then I break it :S
Click to expand...
Click to collapse
sorry but my english is very poor , in the past , i make this tutorial , is in my spanish language but i have pics ,
http://www.htcmania.com/showthread.php?t=833168
[email protected] said:
@0xNOP nop,it doesnt take that long
Click to expand...
Click to collapse
Alright, thanks for letting me know, i know what is causing to behave like that, the thing is that the usb is abruptly getting disconnected, so when it gets detected it starts working like a charm and it starts detecting the phone in the sp flash tool, etc etc but when its about to start really doing anything like flashing or anything concrete the usb simply disconnects and I dont even see it anymore in the Device Manager list... And it appears as "Mt65xx Loader" in the Device Manager, for just few seconds before terminating... Might be that Im using the wrong drivers or The wrong cable ??? Or both??? I'm using an usb cable that was made for an HTC and it had assigned the drivers of my HTC phone... But at the same time, it uses that Mt65xx Loader driver thing that I installed as well...
ZALACAYN2 said:
sorry but my english is very poor , in the past , i make this tutorial , is in my spanish language but i have pics ,
<Link>
Click to expand...
Click to collapse
Hello, my first language is spanish also, so I understood the tutorial, however, you can refer to the reply that i sent to Qwerty, above, since the problem I think is on either the drivers im using or the cable itself....
Hmmmm so your problem is your connection disconnects after flashing starts .I helped a guy who had a similliar problem (his USB disconnected after 3 seconds so the tool doesn't flash ) I'll look it up again .
In the meantime I would like to know the condition of your phone like how you bricked it ,does the phone show any sign of life etc...
[email protected] said:
Hmmmm so your problem is your connection disconnects after flashing starts .I helped a guy who had a similliar problem (his USB disconnected after 3 seconds so the tool doesn't flash ) I'll look it up again .
In the meantime I would like to know the condition of your phone like how you bricked it ,does the phone show any sign of life etc...
Click to expand...
Click to collapse
Yup, Oh Lord, ty, I will really appreciate if you can give me a hand on this one and you're working on it alrdy so I'm really grateful :silly: :good:
Alright, conditions, it does shows signs of life, however, I can get past the boot logo, to the "main screen" where launcher is etc, etc... But the thing is that, since I was working on a rootkit, I disabled many of the processes that I saw were 'suspicious' by suspicious I mean (e.g.) "com.gogle.services" with version: "1.4" instead showing something like process: "com.google.services" with version (e.g.) "version: 4.4.22.493 build: 493823-22-1114" you see.
So I started deleting those processes and installed ES File Manager, which it has a built-in cleaner, so after I finished disabling those processes, I started deleting junk files like a mad man using ES File Manager, and I remember going to the root and deleting the majority of the folders and files that I saw, so probably that's whats happening
Now with that previous story told... Now when I get past the boot logo, I just get this plain black screen, with only the battery status showing up, like literally only that, and the top scrollable menu, I'm able to carry it down but it has no notifications whatsoever, when I plug in the USB (while the phone is on) I get nothing whatsoever from the phone to the computer...
Hope this info helps in debugging whats going on here
Reference: https://youtu.be/jfgDs9eSq0g
Try these and let me know if any of these works
1)try uninstalling the drivers. Then reinstall ,reboot PC and try to flash again
2) does your phone has meta mode? Some mt65xx phone have it. To try accessing it do the following
Load the scatter like usual in sp flash tool ,click download ,now power off your phone(with battery) and connect to pc but hold vol+ button as well .(sometimes you need to hold the vol+ button throughout the whole flashing)
As far as your story goes the final solution is either1) flashing your stock ROM or 2)flash a custom recovery and install a custom rom but both of these require the sp flash tool process to work.
Edit : you know I'm telling you this because I believe you tried factory reset already ,if you havnt try it first.
Sp flash tool is for unbricking mostly.
[email protected] said:
Try these and let me know if any of these works
1)try uninstalling the drivers. Then reinstall ,reboot PC and try to flash again
2) does your phone has meta mode? Some mt65xx phone have it. To try accessing it do the following
Load the scatter like usual in sp flash tool ,click download ,now power off your phone(with battery) and connect to pc but hold vol+ button as well .(sometimes you need to hold the vol+ button throughout the whole flashing)
As far as your story goes the final solution is either1) flashing your stock ROM or 2)flash a custom recovery and install a custom rom but both of these require the sp flash tool process to work.
Click to expand...
Click to collapse
Alright, thanks for the suggestions, I will try to do all of them and get back with results, hopefully with a fixed phone :S :S :S :good:
Just so you know ,I edited my previous post
[email protected] said:
Just so you know ,I edited my previous post
Click to expand...
Click to collapse
Thank you for everything!
Finally got it to work! everything was working good, except the phone itself since it was semi-bricked apparently it couldn't make it to activate the usb system itself... however I went to SP Flash Tool and instead using only "Download" option, I instead used "Format All + Download" ... And then the USB didn't disconnected anymore and then I saw the tool working on it and the progress bars running perfectly! it took like less than 50 seconds to do everything when I saw the big green check mark on my screen!!!!!!!!!!!!!!! AMAZING!! Thanks!
0xNOP said:
Thank you for everything!
Finally got it to work! everything was working good, except the phone itself since it was semi-bricked apparently it couldn't make it to activate the usb system itself... however I went to SP Flash Tool and instead using only "Download" option, I instead used "Format All + Download" ... And then the USB didn't disconnected anymore and then I saw the tool working on it and the progress bars running perfectly! it took like less than 50 seconds to do everything when I saw the big green check mark on my screen!!!!!!!!!!!!!!! AMAZING!! Thanks!
Click to expand...
Click to collapse
Glad it worked for you ,good luck
BTW if you like avoiding the default bloatwares you might wanna try a custom ROM like cyanogen .look up development for your phone in xda or 4pda
Hi, please I need your help. I tried to flash stock ROM but I hard bricked my phone. When I connect phone with computer I'm holding volume up button. In device manager it shows "MediaTek USB Port (COM4)" but after three seconds it disconnect. This is why I can't flash ROM. It's everytime disconnect after three seconds.. Please help me.
Maybe you can try to follow this step :http://www.engineerthink.com/blog/2015/11/how-to-unbrick-hard-bricked-android-phone/
If didnt work,maybe there is a problem in your hardware,try to service your phone to service center.
It didn't work.. Is there a way how to solve hardware problem?
Or trt another ways in this website
http://androidflagship.com/3217-fix-damaged-bricked-android-device
My note 10.1 N8000 have the same problem,i try to fix it,but its hard,so i send my phone to service person,they fix the hardware..
How much did you pay?
Growicek said:
Hi, please I need your help. I tried to flash stock ROM but I hard bricked my phone. When I connect phone with computer I'm holding volume up button. In device manager it shows "MediaTek USB Port (COM4)" but after three seconds it disconnect. This is why I can't flash ROM. It's everytime disconnect after three seconds.. Please help me.
Click to expand...
Click to collapse
What tool are you using to flash the stock firmware .and it will be helpful if you say how exactly you bricked it
I'm using SP Flash Tool for flashing.. I tried to flash stock ROM into my Lenovo A536, when it was done I unplugged phone from computer and tried to power on but there was a problem.. Phone was hard bricked
Growicek said:
I'm using SP Flash Tool for flashing.. I tried to flash stock ROM into my Lenovo A536, when it was done I unplugged phone from computer and tried to power on but there was a problem.. Phone was hard bricked
Click to expand...
Click to collapse
So your saying the flashtool bricked your phone ?
Where did you get the firmware for your phone cuz flash tool can only brick your device if you used firmware not for your phone. Also does your phone shows any sign of life ie vibrate turn on for a sec, bootloop etc...
I don't remember where did I find it.. There is only one sign of phone life. When I connect it with computer, phone connect but only for a while, after a three seconds disconnect.
Growicek said:
I don't remember where did I find it.. There is only one sign of phone life. When I connect it with computer, phone connect but only for a while, after a three seconds disconnect.
Click to expand...
Click to collapse
I know two guys who had this problems.
1) guy took it to service ,they fixed it.
2) installed phone drivers again and tried again and it worked.
If you're confident you have the right firmware load scatter click download and connect your powered off phone without pressing any buttons ,and see if it works.
Anyway I'm narrowing down the cause of the problem to either an incorrect firmware or a sp flash tool version (some version are ****)
Didn't work
Growicek said:
Didn't work
Click to expand...
Click to collapse
Pull out the battery then leave it for 10 min reinsert and see if it boots (give it some time ) .if it doesn't
Or connect your phone to PC(without battery) ,load scatter click download on sp flash tool ,then put in the battery .
First method - didn't work
Second method - device automatically disconnect after three seconds, so SP flash tool says error
Growicek said:
First method - didn't work
Second method - device automatically disconnect after three seconds, so SP flash tool says error
Click to expand...
Click to collapse
What error code?
I bricked my device same as you so I could help you further but my device connected in meta mode and flashed its firmware fine ,so try another USB cord
Ps I've pretty much mentioned all I know about unbricking in this thread so I can't be of further help.https://www.google.co.in/url?sa=t&s...ggeMAA&usg=AFQjCNGkwgZbNQCJFWtm90DM-Mksnzk0dA look this up specifically #9
It didn't work.. Error is: BROM ERROR : S_FT_ENABLE_DRAM_FAIL (4032)
Wow! I did something and then uninstalled driver. When I connected phone, driver automatically installed and now it's not disconnecting, but still can't flash it
Growicek said:
Wow! I did something and then uninstalled driver. When I connected phone, driver automatically installed and now it's not disconnecting, but still can't flash it
Click to expand...
Click to collapse
That's great ,what's the problem now ? Still brom error or download stuck st 0% or any other?
Still same brom error
Growicek said:
Still same brom error
Click to expand...
Click to collapse
Brom error is mostly related to see improper firmware which also explains why you're phone got bricked in the first place .
Try downloading another stock firmware
Man? I love you!!! I tried about four ROMs and the fourth is working!! .. There was a one more problem with flashing again with drivers, idk why but they dissapear, so I installed them again and then tried flash ROM.. Thank you very much! You saved my money!
So I recently changed phones, as one of my main hobbies is tinkering with Smartphones and their respective OS's , I decided to Unlock my Xiaomi Redmi 9A (My previous phone) and flashed Ubuntu Touch to it as it was stated as a supported device, using their prebuilt simple installer app seemed to work but midway through the install the installer crashed and the phone powered off, When I turned it I realised it was stuck in a Bootloop, I tried Power + Vol Up for Recovery, that didn't work and neither did Power + Vold Down for Fastboot i tried ADB to push a command to enter EDL (Qualcomm Emergency Download Mode) but that didn't work either. Does any body have any suggestions for how I could get this device running again?
Hector_GH11 said:
Hector_GH11 said:
So I recently changed phones, as one of my main hobbies is tinkering with Smartphones and their respective OS's , I decided to Unlock my Xiaomi Redmi 9A (My previous phone) and flashed Ubuntu Touch to it as it was stated as a supported device, using their prebuilt simple installer app seemed to work but midway through the install the installer crashed and the phone powered off, When I turned it I realised it was stuck in a Bootloop, I tried Power + Vol Up for Recovery, that didn't work and neither did Power + Vold Down for Fastboot i tried ADB to push a command to enter EDL (Qualcomm Emergency Download Mode) but that didn't work either. Does any body have any suggestions for how I could get this device running again?
Click to expand...
Click to collapse
Yea sure, try flashing with Sp Flash Tool
(Btw this device isn't a Qualcomm procesor so no EDL).
You can solve it with Sp Flash Tool
Needs:
- Pc/Laptop
- Usb Cable
- Miui Rom ( Choose your version : https://xiaomifirmwareupdater.com/miui/dandelion/ )
- Mtk Bypass Tool + LibUsb : https://www.bypassfrpfiles.com/2021/02/mediatek-bypass-tool-mct/
( You have some steps to do here - see the website)
-----------------------------------------------------------------
Flashing :
1. Download all the things I gived to you + drivers.
2. Extract and open Sp Flash Tool and MTK Bypass Tool ( Be sure to install the libusb driver)
3.Open MTK Bypass Tool and click on Bypass button.
4. Hold all the buttons from the phone ( or try power + vol up / down, if all doesn't work)
5. When holding the buttons, connect the phone to the pc, wait a few seconds until it finishes to bypass ( Wait ~2 seconds more after bypassing - holding the buttons) ( Hold buttons - connect phone --> PC with usb cable -- wait like 2 seconds after bypassing to work properly.)
6. Open Sp Flash Tool.
7. Select your download agent ( MTK_AllinOne) - from program folder
8. Select your rom in scatter file section ( to be more exactly, choose the mt6765...... File from the rom)
9. Be sure to check Sp Flash Tool Settings - check if u have selected your device port
10. Where it shows - *"Download Only*" ( you can use that, but for me worked Firmware upgrade) - NOT Format
11. Press download button from up
12. If you need help, here is my discord :
raresgabriel #4803
Click to expand...
Click to collapse
Click on " Click to expand" to see the instructions
Rares6567 said:
Click on " Click to expand" to see the instructions
Click to expand...
Click to collapse
Thanks, Will Try!
Hector_GH11 said:
Thanks, Will Try!
Click to expand...
Click to collapse
Ok, Good Luck!!!!
Rares6567 said:
Ok, Good Luck!!!!
Click to expand...
Click to collapse
It's stuck on a Red Bar saying Downloading DA 100%, and it doesn't do anything else. The phone shows up on Mediatek COM Port 5.
It now says USB Device not Recognised. Yada yada yada, USB device corrupted.
Hector_GH11 said:
It now says USB Device not Recognised. Yada yada yada, USB device corrupted.
Click to expand...
Click to collapse
Ok so discord
Rares6567 said:
Ok so discord
Click to expand...
Click to collapse
I still have this problem my pc does not tell me (usb not recognized) What I wanted to do was downgreade from 12.5.6 to 12.0.5. but my redmi is dead
N0tvich said:
I still have this problem my pc does not tell me (usb not recognized) What I wanted to do was downgreade from 12.5.6 to 12.0.5. but my redmi is dead
Click to expand...
Click to collapse
You need to take the phone case and unplug the battery, and try to flash again.
Rares6567 said:
You need to take the phone case and unplug the battery, and try to flash again.
Click to expand...
Click to collapse
The battery thing worked for me (now I can't go from there, Mr. disconnects and Mr. connects) I was able to get there, I don't know how to continue
N0tvich said:
The battery thing worked for me (now I can't go from there, Mr. disconnects and Mr. connects) I was able to get there, I don't know how to continue
Click to expand...
Click to collapse
Unplug and plug the battery and connect phone.
Try reinstalling drivers