Database Info

[Q] Urgent Help needed

Hi Experts,
I was successfully able to flash ICS on my LG O3D but only .bin file and after that i tried to root phone was not sucessfully all the time ,restarted later and now my phone is not switching on properly.It shows LG logo then goes blank. PLEASE HELP.
Thanks in Advance.

When connected its showing charging and in device manager-->other devices showing CDC Serial & LGE COSMO USB Device

Did you try reflash it again ???
Try flash it with "lg smartflash" it tooo easy (just select the .bin file and .fls) .
Good Luck
Sent from my LG-P920

OS_Hacking said:
Did you try reflash it again ???
Try flash it with "lg smartflash" it tooo easy (just select the .bin file and .fls) .
Good Luck
Sent from my LG-P920
Click to expand...
Click to collapse
Thanks a lot for the reply.
I tried but nothing happening..its not detecting as usb to change port to 41.
Is there any other way?? Also for flashing when i insert battery and press volume up and then connect it starts and shows LG logo and goes blank.

It is not showing in PORT in device manager when connected pressing volume + button

Does the phone go to download mode ("S/W upgrade mode ) ?? By insert the battery while you hold vol+ ??
You will see two arrows like the sync symbol in your phone screen . And then the phone will still connected with the PC .
Your problem is easy to fix . Just try to enter download mode . And every thing will be fine .
Good Luck
Sent from my LG-P920

No its not going into download mode. COM is not detecting it.

[email protected] said:
No its not going into download mode. COM is not detecting it.
Click to expand...
Click to collapse
Try hold power on and the vol+ together , then plug it with the PC . Then insert the battery .
Sent from my LG-P920

[email protected] said:
Hi Experts,
I was successfully able to flash ICS on my LG O3D but only .bin file and after that i tried to root phone was not sucessfully all the time ,restarted later and now my phone is not switching on properly.It shows LG logo then goes blank. PLEASE HELP.
Thanks in Advance.
Click to expand...
Click to collapse
You hardbricked your phone if it doesn't go into download mode.
But no panic there is always a solution;
http://forum.xda-developers.com/showthread.php?t=1942836
Follow the guide above. (and I mean every step , however small they may seem)
ICS roms are now pre-rooted so you don't have to root.
Flash Xbsall's Ported custom ics (The one in the guide.)
Then install wkpark's recovery img. (Found here ; http://forum.xda-developers.com/showthread.php?t=1978543)
Boot into recovery.
Install Darkroom ICS Int. (It's the best in my opinion) or whatever rom you wish.
They are all pre-rooted.
If you can't i'll guide you through it.
Hope i Helped.
Cheers!

boltthrower56 said:
You hardbricked your phone if it doesn't go into download mode.
But no panic there is always a solution;
http://forum.xda-developers.com/showthread.php?t=1942836
Follow the guide above. (and I mean every step , however small they may seem)
ICS roms are now pre-rooted so you don't have to root.
Flash Xbsall's Ported custom ics (The one in the guide.)
Then install wkpark's recovery img. (Found here ; http://forum.xda-developers.com/showthread.php?t=1978543)
Boot into recovery.
Install Darkroom ICS Int. (It's the best in my opinion) or whatever rom you wish.
They are all pre-rooted.
If you can't i'll guide you through it.
Hope i Helped.
Cheers!
Click to expand...
Click to collapse
Thanks a lot for the help and i really appreciate your willingness to take me out of this trouble, Thanks again

Everything worked fine till step 9..But still not showing anything in Ports

Make sure the drivers are correctly installed. Especially omap4430...
Start the script that has been referred to in the guide.
Shut down the phone , remove the battery , plug usb cable and when you see "waiting for 5 seconds" plug in the battery. That should work.
Keep me posted.
Sent from my LG-P920 using xda app-developers app

Its showing s/w update image in phone but getting message USB device not detected in PC

Thanks alot boltthrower56 .
Finally able to recover my phone and restored 3 month old backup.
By the way may i know your real name .
Can you please help me with upgrading to ICS?

[email protected] said:
Its showing s/w update image in phone but getting message USB device not detected in PC
Click to expand...
Click to collapse
That may mean you have a bad cable.
But if you restored it , it's probably sometimes bad or you changed it or you used the front panel which is a hub (divides bandwidth , slows flashing process) and it's bad for ya.
Since my real name is turkish and hard to spell i'll give one better ;
Call me John.
If you must know my real name is "Dogukan".
And yes i can help you with that although it's relatively easy now that you got a hold of it.

Thanks a lot Dogukan..
Are you into android development? Am a real noob in this and you helped me coming out of really difficult situation.
Now i want to root my phone and everytime its showing 'error no device find'

I'm not into android development... my skills lie in networking so there is not much i can do for android.
But those are common knowledge...
I bricked my phone several times to learn those.
You don't need to root. Follow wkpark's recovery installation and flash a custom rom (Darkroom int is great)
Sent from my LG-P920 using xda app-developers app

Soft brick Cubot x6/MT6592 device

Hello everyone I have a few questions. First to say that I'm not new to android yet I don't think I'm very advanced. Anyway here is my situation: I have brand new chinese phone Cubot x6 which is with MT6592 chipset(or CPU I'm not sure). I rooted the device with Framaroot and everything was OK. Then I found CWM for the device on needrom(dot)com and when I flashed the recovery with "Flashify" it rebooteed but it is now stuck on the kernel logo. I can enter only in recovery which is still the stock one . I can't do anything except entering into the stock recovery. I have the stock ROM but it is NOT in a flashable .zip but in a folder which is used by some flashtool program (not the one for Sony but rather for MT devices) I have the stock boot.img, recovery.img and system.img. When I try to "apply update from sideload" and sideload either the boot or recovery images I get "installation aborted". If you guys can tell me how to enter fastboot mode and from there to flash system.img OR any other way to fix the phone please tell me.
P.S. The hardware buttons are only volume rockers and power button. I also tried to install MUIU but it can't flash it with stock recovery.

Please help me. I would be able to manage it somehow if I'm able to use adb, but I can't within the stock recovery.

hello dont problem use sp flashtool and flash rom stock
http://www.needrom.com/mobile/cubot-x6/
ROM
http://www.needrom.com/wp-content/uploads/2014/05/G807_C1_D1_CUBOT_V0.9.rar
SP FLASH TOOL
http://www.needrom.com/wp-content/uploads/2014/01/SP_Flash_Tool_v5.1348.00.zip
Description
ROM Mobile Cubot X6 – ROM Android 4.2.2
ONLY MT6592
Official ROM Cubot X6 Version: G807_C1_D1_CUBOT_V0.9
Gapps include – No Rooted
Language support: Multilang
Install ROM:
- Unpack FlashTools, and Click on Flash_tool.exe
- Select a the MT6592_Android_scatter_emmc.txt in ROM
- Wait file to be added into Flash Tool
- choose Option->USB Model,click USB Model
–> Choose Option->DA DownLoad All->Speed->High Speed, click High Speed
- Turn off your phone, remove the battery.
- "Press F9 (hit Download button)" OR " if upgrade ROM Firmware->Upgrade "
- and connect your phone into the computer via USB data cable.
- The process will start and a red progress bar will appear after color purple, yellow.
- And green circles display
- Finish !
- You can now safely disconnect your phone and turn it on.

Would it be possible for you to upload it to a different site? it seems that the download just cuts off all the time. I tried about 5 times after 10 mins it just stops. I bricked my phone the first day cuz i didnt know it wasnt compatible with Xposed installer
ZALACAYN2 said:
hello dont problem use sp flashtool and flash rom stock
http://www.needrom.com/mobile/cubot-x6/
ROM
http://www.needrom.com/wp-content/uploads/2014/05/G807_C1_D1_CUBOT_V0.9.rar
SP FLASH TOOL
http://www.needrom.com/wp-content/uploads/2014/01/SP_Flash_Tool_v5.1348.00.zip
Description
ROM Mobile Cubot X6 – ROM Android 4.2.2
ONLY MT6592
Official ROM Cubot X6 Version: G807_C1_D1_CUBOT_V0.9
Gapps include – No Rooted
Language support: Multilang
Install ROM:
- Unpack FlashTools, and Click on Flash_tool.exe
- Select a the MT6592_Android_scatter_emmc.txt in ROM
- Wait file to be added into Flash Tool
- choose Option->USB Model,click USB Model
–> Choose Option->DA DownLoad All->Speed->High Speed, click High Speed
- Turn off your phone, remove the battery.
- "Press F9 (hit Download button)" OR " if upgrade ROM Firmware->Upgrade "
- and connect your phone into the computer via USB data cable.
- The process will start and a red progress bar will appear after color purple, yellow.
- And green circles display
- Finish !
- You can now safely disconnect your phone and turn it on.
Click to expand...
Click to collapse

http://pan.baidu.com/s/1jGn3mvk
Enviado desde mi CUBOT X6 mediante Tapatalk

Thank you very much
ZALACAYN2 said:
http://pan.baidu.com/s/1jGn3mvk
Enviado desde mi CUBOT X6 mediante Tapatalk
Click to expand...
Click to collapse

I know this is an old thread, but please understand that I'm following this and I need help as I have the same phone and I haven't found any other updated threads on this topic.
ZALACAYN2 said:
Install ROM:
- Unpack FlashTools, and Click on Flash_tool.exe
- Select a the MT6592_Android_scatter_emmc.txt in ROM
- Wait file to be added into Flash Tool
- choose Option->USB Model,click USB Model
–> Choose Option->DA DownLoad All->Speed->High Speed, click High Speed
- Turn off your phone, remove the battery.
- "Press F9 (hit Download button)" OR " if upgrade ROM Firmware->Upgrade "
- and connect your phone into the computer via USB data cable.
- The process will start and a red progress bar will appear after color purple, yellow.
- And green circles display
- Finish !
- You can now safely disconnect your phone and turn it on.
Click to expand...
Click to collapse
I'm following this, as I tried to do this before, I was apparently doing something wrong and I couldn't get to the part where the program would actually flash it and it never showed progress bars or even detected the phone, now finally my phone is recognized by the program and it's now stuck on the red progress bar, when I put my mouse over it says "Download DA Now..." ?? what is it?
Should I do something, I don't wanna stop it with fear it may brick completely...
7 mins has passed, do I leave it there? I just saw the red progress bar going up to 100% and stay there... Nothing more, purple, or yellow :crying:
Does it usually takes that much? Another thing is that I don't see the device (usb) showing up in the Device Manager... is something going on? the sp flash tool might have become stuck on it doing nothing, but like I said, I dont wanna stop it with fear it might be actually doing something, and then I break it :S

@0xNOP nop,it doesnt take that long

0xNOP said:
I know this is an old thread, but please understand that I'm following this and I need help as I have the same phone and I haven't found any other updated threads on this topic.
I'm following this, as I tried to do this before, I was apparently doing something wrong and I couldn't get to the part where the program would actually flash it and it never showed progress bars or even detected the phone, now finally my phone is recognized by the program and it's now stuck on the red progress bar, when I put my mouse over it says "Download DA Now..." ?? what is it?
Should I do something, I don't wanna stop it with fear it may brick completely...
7 mins has passed, do I leave it there? I just saw the red progress bar going up to 100% and stay there... Nothing more, purple, or yellow :crying:
Does it usually takes that much? Another thing is that I don't see the device (usb) showing up in the Device Manager... is something going on? the sp flash tool might have become stuck on it doing nothing, but like I said, I dont wanna stop it with fear it might be actually doing something, and then I break it :S
Click to expand...
Click to collapse
sorry but my english is very poor , in the past , i make this tutorial , is in my spanish language but i have pics ,
http://www.htcmania.com/showthread.php?t=833168

[email protected] said:
@0xNOP nop,it doesnt take that long
Click to expand...
Click to collapse
Alright, thanks for letting me know, i know what is causing to behave like that, the thing is that the usb is abruptly getting disconnected, so when it gets detected it starts working like a charm and it starts detecting the phone in the sp flash tool, etc etc but when its about to start really doing anything like flashing or anything concrete the usb simply disconnects and I dont even see it anymore in the Device Manager list... And it appears as "Mt65xx Loader" in the Device Manager, for just few seconds before terminating... Might be that Im using the wrong drivers or The wrong cable ??? Or both??? I'm using an usb cable that was made for an HTC and it had assigned the drivers of my HTC phone... But at the same time, it uses that Mt65xx Loader driver thing that I installed as well...
ZALACAYN2 said:
sorry but my english is very poor , in the past , i make this tutorial , is in my spanish language but i have pics ,
<Link>
Click to expand...
Click to collapse
Hello, my first language is spanish also, so I understood the tutorial, however, you can refer to the reply that i sent to Qwerty, above, since the problem I think is on either the drivers im using or the cable itself....

Hmmmm so your problem is your connection disconnects after flashing starts .I helped a guy who had a similliar problem (his USB disconnected after 3 seconds so the tool doesn't flash ) I'll look it up again .
In the meantime I would like to know the condition of your phone like how you bricked it ,does the phone show any sign of life etc...

[email protected] said:
Hmmmm so your problem is your connection disconnects after flashing starts .I helped a guy who had a similliar problem (his USB disconnected after 3 seconds so the tool doesn't flash ) I'll look it up again .
In the meantime I would like to know the condition of your phone like how you bricked it ,does the phone show any sign of life etc...
Click to expand...
Click to collapse
Yup, Oh Lord, ty, I will really appreciate if you can give me a hand on this one and you're working on it alrdy so I'm really grateful :silly: :good:
Alright, conditions, it does shows signs of life, however, I can get past the boot logo, to the "main screen" where launcher is etc, etc... But the thing is that, since I was working on a rootkit, I disabled many of the processes that I saw were 'suspicious' by suspicious I mean (e.g.) "com.gogle.services" with version: "1.4" instead showing something like process: "com.google.services" with version (e.g.) "version: 4.4.22.493 build: 493823-22-1114" you see.
So I started deleting those processes and installed ES File Manager, which it has a built-in cleaner, so after I finished disabling those processes, I started deleting junk files like a mad man using ES File Manager, and I remember going to the root and deleting the majority of the folders and files that I saw, so probably that's whats happening
Now with that previous story told... Now when I get past the boot logo, I just get this plain black screen, with only the battery status showing up, like literally only that, and the top scrollable menu, I'm able to carry it down but it has no notifications whatsoever, when I plug in the USB (while the phone is on) I get nothing whatsoever from the phone to the computer...
Hope this info helps in debugging whats going on here
Reference: https://youtu.be/jfgDs9eSq0g

Try these and let me know if any of these works
1)try uninstalling the drivers. Then reinstall ,reboot PC and try to flash again
2) does your phone has meta mode? Some mt65xx phone have it. To try accessing it do the following
Load the scatter like usual in sp flash tool ,click download ,now power off your phone(with battery) and connect to pc but hold vol+ button as well .(sometimes you need to hold the vol+ button throughout the whole flashing)
As far as your story goes the final solution is either1) flashing your stock ROM or 2)flash a custom recovery and install a custom rom but both of these require the sp flash tool process to work.
Edit : you know I'm telling you this because I believe you tried factory reset already ,if you havnt try it first.
Sp flash tool is for unbricking mostly.

[email protected] said:
Try these and let me know if any of these works
1)try uninstalling the drivers. Then reinstall ,reboot PC and try to flash again
2) does your phone has meta mode? Some mt65xx phone have it. To try accessing it do the following
Load the scatter like usual in sp flash tool ,click download ,now power off your phone(with battery) and connect to pc but hold vol+ button as well .(sometimes you need to hold the vol+ button throughout the whole flashing)
As far as your story goes the final solution is either1) flashing your stock ROM or 2)flash a custom recovery and install a custom rom but both of these require the sp flash tool process to work.
Click to expand...
Click to collapse
Alright, thanks for the suggestions, I will try to do all of them and get back with results, hopefully with a fixed phone :S :S :S :good:

Just so you know ,I edited my previous post

[email protected] said:
Just so you know ,I edited my previous post
Click to expand...
Click to collapse
Thank you for everything!
Finally got it to work! everything was working good, except the phone itself since it was semi-bricked apparently it couldn't make it to activate the usb system itself... however I went to SP Flash Tool and instead using only "Download" option, I instead used "Format All + Download" ... And then the USB didn't disconnected anymore and then I saw the tool working on it and the progress bars running perfectly! it took like less than 50 seconds to do everything when I saw the big green check mark on my screen!!!!!!!!!!!!!!! AMAZING!! Thanks!

0xNOP said:
Thank you for everything!
Finally got it to work! everything was working good, except the phone itself since it was semi-bricked apparently it couldn't make it to activate the usb system itself... however I went to SP Flash Tool and instead using only "Download" option, I instead used "Format All + Download" ... And then the USB didn't disconnected anymore and then I saw the tool working on it and the progress bars running perfectly! it took like less than 50 seconds to do everything when I saw the big green check mark on my screen!!!!!!!!!!!!!!! AMAZING!! Thanks!
Click to expand...
Click to collapse
Glad it worked for you ,good luck
BTW if you like avoiding the default bloatwares you might wanna try a custom ROM like cyanogen .look up development for your phone in xda or 4pda

Help me, to fix dead bricked Xperia C c2305

I flashed a wrong recovery img from Mobileuncle tools,from then the phone is not booting,it is not getting detected in Sony pc companion and wmshua flash tools.
Only red led glows for some time,,when connected to pc.
Plz help me

Try this
baselrabia said:
I flashed a wrong recovery img from Mobileuncle tools,from then the phone is not booting,it is not getting detected in Sony pc companion and wmshua flash tools.
Only red led glows for some time,,when connected to pc.
Plz help me
Click to expand...
Click to collapse
I am not a power user. However, It happened to me once. I did the following
1- Open the wmshua flash tools, select the ROM file.
2- Connect a usb.
3- Keep rebooting by holding volume down and Power.
I did not know how it worked for me but it did.
Good luck.
---------- Post added at 04:26 AM ---------- Previous post was at 04:09 AM ----------
Visit this link please.
I cannot post outside link so try this,
Search informationlord dot com
---> ultimate-guide-to-fix-bricked-xperia-c

thutchai said:
I am not a power user. However, It happened to me once. I did the following
1- Open the wmshua flash tools, select the ROM file.
2- Connect a usb.
3- Keep rebooting by holding volume down and Power.
I did not know how it worked for me but it did.
Good luck.
---------- Post added at 04:26 AM ---------- Previous post was at 04:09 AM ----------
Visit this link please.
I cannot post outside link so try this,
Search informationlord dot com
---> ultimate-guide-to-fix-bricked-xperia-c
Click to expand...
Click to collapse
Help Me I Am In Huge Problem , I Had Rooted My Sony Xperia C And Installed 5.0.2 Lollipop Custom Rom But After Somedays The Phone Started Bootlooping Automatically And Now Its Battery Is Fully Drained , I Charged The Phone But Switched Off Charging Battery Symbol Is Not Showing , So I Tried To Flash Sony Xperia C With Flashtool But Flashtool Shows Drivers Not Found m Then I Used WMSHUA Flash Tool But Phone Is Not Detecting , In Device Manager After Connecting Sony Xperia C It Shows "Unknown Device" . i Tried Sony Companion Too,Still Phone Didnt Get Detected , On Device While Charging Or Connecting To Computer Red Led Glows Out , Help Me Please

i keep pushing the buttons.
When it happened to me once. I did the
following,
1- Open the wmshua flash tools,
** I knew that wmshua should detect
phone first, but forget it. **
2- select the ROM file.
3- Connect a usb.
4- Keep rebooting (this is important)
by holding volume down and Power.
keep doing this. In my case i took me
some time. At that moment i have
nothing to lose, so i keep doing this.
And by the way, did you check
the information overlord out?

you need to go to Sony Service Center .
they will charge you around 5k for The New F***G motherboard .
datz all folks .................. mark my word , "DON'T EVER TRY TO MESS WITH ROM'S , KERNAL AND BOOTLOADER" .
if u want to upgrade try buying a new f***ing phone :silly::silly: :good:

Asish RP said:
you need to go to Sony Service Center .
they will charge you around 5k for The New F***G motherboard .
datz all folks .................. mark my word , "DON'T EVER TRY TO MESS WITH ROM'S , KERNAL AND BOOTLOADER" .
if u want to upgrade try buying a new f***ing phone :silly::silly: :good:
Click to expand...
Click to collapse
No, don't mess with the system if there isn't much support or development for it. I regret buying the C3 now because of the horrible camera quality and the fact that the lack of activity is clear. But, it's still a fast phone with good battery management so rooting won't help much.

baselrabia said:
I flashed a wrong recovery img from Mobileuncle tools,from then the phone is not booting,it is not getting detected in Sony pc companion and wmshua flash tools.
Only red led glows for some time,,when connected to pc.
Plz help me
Click to expand...
Click to collapse
Hi.. Have you got this problem solved? Cause i got the same now.. Please any help..
Sent from my Redmi Note 3 using Tapatalk

For me, I've encountered almost the same thing too when flashing my XperiaZ, here's how I fixed it:
Pre-1. To make sure your phone has enough battery left, when holding down the "VolUp" button, connect your phone to a charger. This charges your phone in fastboot mode. It will be slow.
1. In flashtool, open up flashmode, let it load the files (since its a system only flash, you don't need to tick anything) until it prompts you to connect your phone. If the phone is in a boot loop, hold down "Power + VolUp +VolDown" at the same time until it vibrates the hell out of it.
2. When the phone is switched off, hold down the "VolDown" button then quickly connect your phone to your computer. A green light should flash and the phone starts flashing.
3. If this doesn't work, tick the "Wipe Userdata" column so that it can wipe throughly.
Cheers!

KwongTN said:
For me, I've encountered almost the same thing too when flashing my XperiaZ, here's how I fixed it:
Pre-1. To make sure your phone has enough battery left, when holding down the "VolUp" button, connect your phone to a charger. This charges your phone in fastboot mode. It will be slow.
1. In flashtool, open up flashmode, let it load the files (since its a system only flash, you don't need to tick anything) until it prompts you to connect your phone. If the phone is in a boot loop, hold down "Power + VolUp +VolDown" at the same time until it vibrates the hell out of it.
2. When the phone is switched off, hold down the "VolDown" button then quickly connect your phone to your computer. A green light should flash and the phone starts flashing.
3. If this doesn't work, tick the "Wipe Userdata" column so that it can wipe throughly.
Cheers!
Click to expand...
Click to collapse
Thx bro.. I m gonna try it...
Sent from my Redmi Note 3 using Tapatalk

[Guide/Info] [How To] Unbrick your Bricked MTK Devices (Dead Brick)

This thread is about how to recover the MTK Android phone, if it has gone Bricked (soft/hard/dead/etc)
THIS IS FOR INFORMATION ONLY.
Q. How Phone gets Bricked?
Ans : Basically, phone get bricked during the installation of Android OS (flashing).
Reason/why it happens
- If flashing is interrupted by low battery or loose cable connection during flashing.
- Using wrong firmware or a custom ROM (unstable) to flash your phone.
Result:
* Phone will not boot even after holding the power key and it will not accept charging. (Hard Brick / Dead Brick)
* Boot-Loop
* Restart loop
* No Recovery (In this situation, Hard Reset will not work)
Q. - Why Phone becomes dead (MTK Android Phone) ?
Ans : While installing Custom ROM or Stock firmware (unstable), Preloader (.bin) file becomes corrupted.
PRELOADER - It is the file in MTK android phone which helps to boot the phone.
Tools & Software Required:
SP Flash tool
Android Stock ROM
MTK USB Driver
PC / Laptop
Dead MTK Phone
USB cable.
NOTE: SP Flash tool has 3 Dropdown, Its meaning & How to use:
MOTA SIU : while choosing this function before clicking on Download, only boot, recovery and Android will be updated.
Format All + Download : while choosing this function before clicking on Download, it first erases the old Firmware then install new firmware. (Recommended when MTK phone stuck at logo & hard reset fails)
Firmware Upgrade: while choosing this function before clicking on Download, its update the Android version. (Recommended when installing a higher or lower version of Android manually)
Steps to Fix/Unbrick Dead Android (MTK) Phone​
1- Install MTK driver.
2- Download the tool.
3- Unzip it and double click on Flash_tool.exe.
4- It will launch the tool.
5- Download Android stock ROM, unzip it.
6- Click on Scatter-Loading and assign the path of file (Select Firmware i.e. {.txt extension}).
7- Click on Download.
8- Switch off Mobile and connect it to PC using USB cable by pressing Volume down as boot key.
9- Flashing starts and when completed, Download OK will appear.
Also check Here for more Understanding, Special Thanks to @yuweng
Please let me know if anything is wrong here, so that I can make correction and help other member for better understanding.
Also hit THANKS button if you find this as useful info.
If you found this post helpful then don’t forget to share this post with other Android users so that they could get their dead phones working in few easy steps without paying few dollars on it.

Reserved

Nice Guide, Can you please list MTK devices ????

421rahman said:
Nice Guide, Can you please list MTK devices ????
Click to expand...
Click to collapse
OK, Will be adding attachments later, Thanks
Salman

--

Thanks @Salman Al-Badgail for this use full info.

Deena Khanam said:
Thanks @Salman Al-Badgail for this use full info.
Click to expand...
Click to collapse
welcome & Thanks

@jamsubzero check this guide

@jamsubzero I saw your post and thread regarding Dead Bricked
Hey guys.
I own a lenovo A328. For the past couple of months my phone, gets poping up "com.google.etc.etc has stopped".
I tried doing a factory reset, but no luck. Then I learn that I can flash it using SPflash tool with the stock firmware.
And luckily, I did it, my phone back to normal. But then, a few couple of weeks, it started to pop up the same error messages again until I can't do anything on my phone, and unitl it boot loops. So, I reflash again with the same firmware (stock).. and it works again. And same thing keeps repeating and repeating;
until I thought I can try to change the options in sp flash tool..
Instead of "Download only", I choose, "Firmware upgrade".... the flashing finished successfully.
BUT when I press the power button to turn it on, nothing happens, and when I charge it, I cant see the charging screen (or it's not actually charging). I'm sure that it is charging before the flashing, and the power button is working.
When I connect it to the computer, i hear a "connected" sound, then "disconnected", and repeating.
i also tried to reflash it, both the "DL only" and "Firmware upgrade", even the "Format all + ...."
and it flashed successfully (meaning, computer still recognized it), but still not turning on.
Please help me. please.
Click to expand...
Click to collapse
NEVER DOWNLOAD ROM NOT MEANT FOR YOUR PHONE. IT WILL BRICK IT !
What you did is you flashed wrong firmware to your device and the result you in Dead Brick, However there is still solution for your problem. Please Please Please do a proper search first and download correct firmware and other necessary files for your device. Please check firmware number ok.
You can Flash it again but you need to open phone and try, Check here for better understanding.
GUIDE : HERE. Or else please go to any mobile shop and ask them to flash. Dont tell the original reason that you tried to flash or etc. Tell them that it stop suddenly and for now I am unable to access it. They charge you about 5-15 USD based on your country, for me they had charged 10U$D me for lenovo A3500-HV dead flashing. Hope this help you.

i got no scatter file in stock rom pls help!

Aller retour si flash tool

Hard bricked Lenovo a7000
**Hi I got problem on yesterday I was install ing new Rom but suddenly my Lenovo a7000 hard brick
It is not responding any point .even charging .and charging light also .it's dead
But it when I connet to my pc it's connecting sound conning from pc ....My phone is dead plaease help

Salman Al-Badgail said:
This thread is about how to recover the MTK Android phone, if it has gone Bricked (soft/hard/dead/etc)
THIS IS FOR INFORMATION ONLY.
Q. How Phone gets Bricked?
Ans : Basically, phone get bricked during the installation of Android OS (flashing).
Reason/why it happens
- If flashing is interrupted by low battery or loose cable connection during flashing.
- Using wrong firmware or a custom ROM (unstable) to flash your phone.
Result:
* Phone will not boot even after holding the power key and it will not accept charging. (Hard Brick / Dead Brick)
* Boot-Loop
* Restart loop
* No Recovery (In this situation, Hard Reset will not work)
Q. - Why Phone becomes dead (MTK Android Phone) ?
Ans : While installing Custom ROM or Stock firmware (unstable), Preloader (.bin) file becomes corrupted.
PRELOADER - It is the file in MTK android phone which helps to boot the phone.
Tools & Software Required:
SP Flash tool
Android Stock ROM
MTK USB Driver
PC / Laptop
Dead MTK Phone
USB cable.
NOTE: SP Flash tool has 3 Dropdown, Its meaning & How to use:
MOTA SIU : while choosing this function before clicking on Download, only boot, recovery and Android will be updated.
Format All + Download : while choosing this function before clicking on Download, it first erases the old Firmware then install new firmware. (Recommended when MTK phone stuck at logo & hard reset fails)
Firmware Upgrade: while choosing this function before clicking on Download, its update the Android version. (Recommended when installing a higher or lower version of Android manually)
Steps to Fix/Unbrick Dead Android (MTK) Phone
1- Install MTK driver.
2- Download the tool.
3- Unzip it and double click on Flash_tool.exe.
4- It will launch the tool.
5- Download Android stock ROM, unzip it.
6- Click on Scatter-Loading and assign the path of file (Select Firmware i.e. {.txt extension}).
7- Click on Download.
8- Switch off Mobile and connect it to PC using USB cable by pressing Volume down as boot key.
9- Flashing starts and when completed, Download OK will appear.
Also check Here for more Understanding, Special Thanks [email protected]
Please let me know if anything is wrong here, so that I can make correction and help other member for better understanding.
Also hit THANKS button if you find this as useful info.
If you found this post helpful then don’t forget to share this post with other Android users so that they could get their dead phones working in few easy steps without paying few dollars on it.
Click to expand...
Click to collapse
S
Sir please help me out
I have Micromax a120 device. Few days back it got bricked it stuck on bootloop and not working even after factory reset moreover my pc is not recognizing mobile and display message as device descriptor request failed. I have installed all drivers
---------- Post added at 07:47 PM ---------- Previous post was at 07:47 PM ----------
Salman Al-Badgail said:
Reserved
Click to expand...
Click to collapse
Sir please help me out
I have Micromax a120 device. Few days back it got bricked it stuck on bootloop and not working even after factory reset moreover my pc is not recognizing mobile and display message as device descriptor request failed. I have installed all drivers

im having mt8127 mtk device it is not flashing iam having corrupted preloader i tried to flash the preloader it is not flashing , can any body knows to fix it??

How can a phone that's bricked be switched off? Am a bit confused.

Salman Al-Badgail said:
This thread is about how to recover the MTK Android phone, if it has gone Bricked (soft/hard/dead/etc)
THIS IS FOR INFORMATION ONLY.
Q. How Phone gets Bricked?
Ans : Basically, phone get bricked during the installation of Android OS (flashing).
Reason/why it happens
- If flashing is interrupted by low battery or loose cable connection during flashing.
- Using wrong firmware or a custom ROM (unstable) to flash your phone.
Result:
* Phone will not boot even after holding the power key and it will not accept charging. (Hard Brick / Dead Brick)
* Boot-Loop
* Restart loop
* No Recovery (In this situation, Hard Reset will not work)
Q. - Why Phone becomes dead (MTK Android Phone) ?
Ans : While installing Custom ROM or Stock firmware (unstable), Preloader (.bin) file becomes corrupted.
PRELOADER - It is the file in MTK android phone which helps to boot the phone.
Tools & Software Required:
SP Flash tool
Android Stock ROM
MTK USB Driver
PC / Laptop
Dead MTK Phone
USB cable.
NOTE: SP Flash tool has 3 Dropdown, Its meaning & How to use:
MOTA SIU : while choosing this function before clicking on Download, only boot, recovery and Android will be updated.
Format All + Download : while choosing this function before clicking on Download, it first erases the old Firmware then install new firmware. (Recommended when MTK phone stuck at logo & hard reset fails)
Firmware Upgrade: while choosing this function before clicking on Download, its update the Android version. (Recommended when installing a higher or lower version of Android manually)
Steps to Fix/Unbrick Dead Android (MTK) Phone​
1- Install MTK driver.
2- Download the tool.
3- Unzip it and double click on Flash_tool.exe.
4- It will launch the tool.
5- Download Android stock ROM, unzip it.
6- Click on Scatter-Loading and assign the path of file (Select Firmware i.e. {.txt extension}).
7- Click on Download.
8- Switch off Mobile and connect it to PC using USB cable by pressing Volume down as boot key.
9- Flashing starts and when completed, Download OK will appear.
Also check Here for more Understanding, Special Thanks to @yuweng
Please let me know if anything is wrong here, so that I can make correction and help other member for better understanding.
Also hit THANKS button if you find this as useful info.
If you found this post helpful then don’t forget to share this post with other Android users so that they could get their dead phones working in few easy steps without paying few dollars on it.
Click to expand...
Click to collapse
i am trying to flash vivo s7 and the cable shake and since then the phone is dead, have flashed it several time, it complete but it refuse to on

I need help please
Basically I was flashing updates for my CUBOT Nova and everything was going fine and I tried out this custom recovery which wouldn't mount any partition so it didn't really suit me. And I did this a dozen of times with other recoveries and if anything happened I had the firmware in SP tools ready to be flashed and if I could save going to it I just used the fastboot to flash it, and so I decided to completly stop and just put my phone back to normal and because I done it before I formatted the whole flash, (and FYI every 2 times I plugged in the phone powered off my computer always searched for drivers in the windows update but it failed and so everything still worked) but after I formatted it and plugged it out and in to download the firmware, my computer successfully installed the drivers and at this moment I was like shoot so I tried to download and it didnt recognise my phone and so I uninstalled the driver my computer installed and see if it worked and it kept installing it again, so I decided to uninstall every mtk driver I had and rebooted, when I installed every single driver again it tried to download drivers from the windows update but it failed and on the sp flash tools it goes to 100% on the Downloading DA (so the red bar) and stays like that for a while and I get notifications that I have a unrecognisable usb device and after a while it gives me randomly 2 errors 0xC0050005 and 0XC0060001 and I know someone is going to tell me I dont have the right firmware or that it's not the right ones but it isn't I got from the official Cubot website and I got an early versions from firmwarefiles I think and none of them work, now I just have a phone without anything on it and I cant flash anything on it until I just hope someone would walk me through what to do I would appreciate so much I'm sorry I wrote so much as I had to explain in max detail as I could what happened!

netcrafy said:
How can a phone that's bricked be switched off? Am a bit confused.
Click to expand...
Click to collapse
i wanted to say the same thing, also i tried enter EDL for 2 days DD (helio G80) LMFAO

Hi there
I would like to know if you can help me in repairing my device.
So i wanted to do an upgrade on the tablet and i messed it up.
I was on CMW recovery at first and then i did a format on cache system and data. but when i wanted to flash the rom CM14.1 it fail and the devices restarted.
the screen goes on but i can see faint lines on the screen.
I did make a back up of the rom and tried to flash it back but it didnt work.
I used all the roms and it still didnt work. I tried many SP flash tool and formating and still not working. every single rom has been flash and all are green but the phone does not want to boot. i have youtube and followed the instructions and every single step i can think of but u have a gut feeling i am mssing something.
I cannot write SN on the fone as it will not work. i have uninstalled all the drivers re-install all the drivers did all the instruction that you have provided but still it will work.
the tablet does still detect on the PC and it does work. so basically it is in a bootloop but its not powering up. Some suggested using MRT TOOLS or MIRACLES but i have a problem with that as it always have a virus attached it to and when i download it the pc removes it. so i dont know where i can get a good crack tool.
i really need your help if you can.

Hello Guys
i closed SP tool while flashing
my phone : infinix hot 10s
i cant power on it and cant join fastboot and cant join bootloader
When i connect phone by orginial usb
computer said (USB not recoginzed)
i installed all drivers but now phone is dead and he was rooted so i cant going to warranty
how i fix it?

[Guide] Unbrick Your UNLOCKED Lenovo P2a42

Hey Friends,
You must have seen very good days with Lenovo P2 but when there comes a bad day when your phone stops responding to button holds and restarts. You may or may not have a clue what to do to get your phone working again just like before.
I got into this situation where only thing my phone was able to operate was a RED LED on connecting it to my laptop. Then I had to read tens of pages on XDA to find answers to all my questions. If you are in such a situation and your phone is UNLOCKED then you have come to the right place. Procedure is quite simple but remember, I am writing this guide to define complete process from blackout to complete update so follow this guide as per your needs.
I faced this situation of Total Blackout / Dead Phone (Almost) with only Red LED working and it can be very scary. So, here is the simplest procedure you can follow. I want to appreciate all those people who helped me in finding a way to boot my phone with each and everything working. Long story short, let's get this done.
Tools Required:
I am mentioning here all the Tools you will need. I will urge you to download and save these tools in case you want to unbrick your phone any time:
1. Minimal ADB and Fastboot setup for PC
2. Lenovo USB drivers v1.1.33
3. Qualcomm USB Drivers
4. Qualcomm Flash Image Loader (QFIL) v2.0.1.9 for your PC in case you have corrupted your phone's IMEI and/ or Baseband
5. Blankflash.bat in case you want to recover from total blackout (Attached)
6. Stock MM S048 Firmware for Lenovo P2 in case phone doesn't boot
7. S048_ModemTelephony.zip in case your phone boots through Stock MM S048 but SIM isn't detected and IMEI is missing. I have made a complete modem zip file for installation through recovery.
8. S251_ModemTelephony.zip in case your phone is on latest firmware and doesn't detect SIM and has lost IMEI. I have made a complete modem zip file for installation through recovery.
9. QCN file for recovering baseband version and giving you most precious network signals. (Attached)
10. WinRAR or PeaZip for uncompressing files
I will recommend you to have a specific folder for keeping all these tools in a single place.
Procedure for Unbricking:
Before going with the procedure, make sure you have downloaded all the files you need, updated Lenovo and Qualcomm drivers etc. Here is the procedure:
1. If total blackout with red LED notification when connecting to PC: Unzip blankflash.zip to a folder in C drive. Now connect your P2 to PC through USB, press volume+, volume- and power button simultaneously and double click blankflash.bat. You might have no success in your first try. Just keep trying and it will load your phone to Fastboot. Restart your phone in TWRP if installed and install a working ROM for your phone after doing a wipe. If all is good and phone works OK then great but if you have lost IMEI and baseband then it is better to reinstate your phone through first MM stock ROM S048
2. Install S048 firmware through Minimal ADB and Fastboot - use flash instructions in .txt file.
3. Wait for startup of phone. Check if fingerprint, BT, WIFI and SIM work if all work then OK.
4. If fingerprint, BT, WIFI and SIM are not working then check IMEI through dialer. Dial *#06#. If IMEI is not available then install latest TWRP through Fastboot.
5. Start P2 in TWRP recovery and install S048_ModemTelephony.zip. Restart phone to see if WIFI and SIM work.
6. If SIM is detected but not giving signals and Baseband is shown as unknown then extract 000000_0.qcn file given in .7z and restore through QFIL and restart your phone into Fastboot.
7. Now, install stock recovery of S048 firmware through Fastboot and restart your phone.
8. Use your phone like you normally do and update your P2 till firmware S251 and see if everything works including calls. Update your phone through OTA.
9. After OTA installation, stock recovery may say that update failed. Just press Back, go into Wipe user data menu and Wipe Cache only. Restart your phone which will be updated to latest version and will ask you to update to a newer version. Allow it to download the next update.
10. After installation of S251 update, install latest TWRP through Fastboot and install most recent version of LOS 16 so that your vendor partition is stable and free from any bloated files. Now, use your phone just like you want to.
If you need further clarification then ask in this thread.

Bro my phone is not unlocked can i try thz one

Ranji007 said:
Bro my phone is not unlocked can i try thz one
Click to expand...
Click to collapse
You should download S048 and use flashall.bat inside that archive to install it all. However, if you lose IMEI or baseband then you can use modem and qcn files given in this thread.

alirazaagha said:
You should download S048 and use flashall.bat inside that archive to install it all. However, if you lose IMEI or baseband then you can use modem and qcn files given in this thread.
Click to expand...
Click to collapse
Bro now i wanna use ...minimal adb ..my phone is totally bricked only red light glowing

Ranji007 said:
Bro now i wanna use ...minimal adb ..my phone is totally bricked only red light glowing
Click to expand...
Click to collapse
don't worry just flash blank flash from the link given in the op, you will get the bootloader back

hackiee said:
don't worry just flash blank flash from the link given in the op, you will get the bootloader back
Click to expand...
Click to collapse
Bro how to connect my phone to blank flash...can u PLZZ help

hackiee said:
don't worry just flash blank flash from the link given in the op, you will get the bootloader back
Click to expand...
Click to collapse
Laptop is not detecting my device bro i installed all lenovo and Qualcomm drivers...any idea

Ranji007 said:
Laptop is not detecting my device bro i installed all lenovo and Qualcomm drivers...any idea
Click to expand...
Click to collapse
If red light blinks, your phone can be detected by your laptop. Check ports in device manager settings and you'll see a new port with Qualcomm 9800 series number. If that's there, try blankflash to start in fastboot. It might need some tries before startup. Be patient and keep trying till you are in fastboot.

alirazaagha said:
If red light blinks, your phone can be detected by your laptop. Check ports in device manager settings and you'll see a new port with Qualcomm 9800 series number. If that's there, try blankflash to start in fastboot. It might need some tries before startup. Be patient and keep trying till you are in fastboot.
Click to expand...
Click to collapse
Bro ..thanks for reply....in my phone red blink is glowing continuously ..but after connecting there is no change...can u say which buttons i want to press?

Ranji007 said:
Bro ..thanks for reply....in my phone red blink is glowing continuously ..but after connecting there is no change...can u say which buttons i want to press?
Click to expand...
Click to collapse
Press Volume+, Volume- and Power simultaneously and double click flashblank.bat. It might take some tries to finally install the scripts and start phone in fastboot. It took me 20+ tries to finally detect my phone through blankflash. Please, read OP completely.

alirazaagha said:
Press Volume+, Volume- and Power simultaneously and double click flashblank.bat. It might take some tries to finally install the scripts and start phone in fastboot. It took me 20+ tries to finally detect my phone through blankflash. Please, read OP completely.
Click to expand...
Click to collapse
Bro we want to connect each time removing usb cable and connect again like that ..we wanna do 20 times??

Ranji007 said:
Bro we want to connect each time removing usb cable and connect again like that ..we wanna do 20 times??
Click to expand...
Click to collapse
No. Keep USB connected. Try blankflash. If it doesn't detect phone or go ahead. Close command terminal, double click again and keep doing it till it processes the files. If it is stuck somewhere. Close terminal and try again.

alirazaagha said:
No. Keep USB connected. Try blankflash. If it doesn't detect phone or go ahead. Close command terminal, double click again and keep doing it till it processes the files. If it is stuck somewhere. Close terminal and try again.
Click to expand...
Click to collapse
Bro is there any solution ..i continuously pressed volume and power buttons connected to laptop and opening blank flash continuously for number of times ...but there was no reaction...only waiting for device is showing ? on my pc ...

Ranji007 said:
Bro is there any solution ..i continuously pressed volume and power buttons connected to laptop and opening blank flash continuously for number of times ...but there was no reaction...only waiting for device is showing ? on my pc ...
Click to expand...
Click to collapse
Check if your USB cable is alright and appropriate drivers are installed. Otherwise reinstall drivers, restart your PC and try again.

alirazaagha said:
Check if your USB cable is alright and appropriate drivers are installed. Otherwise reinstall drivers, restart your PC and try again.
Click to expand...
Click to collapse
Bro we want to change any settings in device manager ...?

Ranji007 said:
Bro we want to change any settings in device manager ...?
Click to expand...
Click to collapse
No. Just update drivers.

alirazaagha said:
No. Just update drivers.
Click to expand...
Click to collapse
Bro when u take to service center they said for u motherboard problem or something??

Ranji007 said:
Bro when u take to service center they said for u motherboard problem or something??
Click to expand...
Click to collapse
Fortunately, I never took it there.

alirazaagha said:
Fortunately, I never took it there.
Click to expand...
Click to collapse
My phone was fallen in water then i changed the display..few days after it stopped working ..and when i take to serive centre they said to change motherboard..but it's the 80% of phone price...so iam here ?..iam trying thiz method

Ranji007 said:
My phone was fallen in water then i changed the display..few days after it stopped working ..and when i take to serive centre they said to change motherboard..but it's the 80% of phone price...so iam here ..iam trying thiz method
Click to expand...
Click to collapse
I think you might have damaged some hardware. But anyway if you want to use blankflash, I have a method.
In lenovo p2 we have another mode called QDloader mode, in which we can use blankflash. For entering into this mode, it's little tricky but, can enter in one or two go.
So, here's how:
1. Switch off the mobile.
2. Press the volume up key,
3. While holding the volume up key, insert the usb cable and at the same time press the power button (this is the trick, we have to insert and hit at the same time).
And voila! :highfive: you will see black screen with only red notification led blinking.
we are into QDloader mode. Now use blankflash :good: