Database Info

Archos 7 Home Tablet bricked ;(

Hi, I tried to install a rom such as an update (I took the update.img into the root of my archos and It started to update) but when it rebooted It did not start ... So I bricked my Archos 7 HT ;(
Do you know how can I unbrick my archos 7 ht, please ???
(Sorry for my poor english, but I am italian...)
Sent from my iPhone using Tapatalk

Anyone can help me ???
;((
Sent from my iPhone using Tapatalk

Hi,
look here:
http://forum.archosfans.com/viewforum.php?f=59
Then also watch "unbrick APAD" these are the same platforms RK2808.
http://www.slatedroid.com/index.php?topic=5092.0
http://www.youtube.com/watch?v=rqSydpZumno
Good luck

anyone knows where can i download rmandroiddm.exe ?

I restored it using this tuto
If you have a device which is not recognizable by the PC:
You need a 32-bit Windows (I used WinXP VMware player image from my Win7 64-bit)
In my case connecting the device to the PC did not resulted in access to the memory, only the drive letters appeared, but could not be mounted.
At the same time, the RKandroid tool did not recognize the device at all.
So, we need to reflash the archos 7ht. For this we need to enter update mode - and here is the trick:
1. Shutdown the tablet (in my case - pin reset shutdowns it)
2. LOCK the sliding button (for me this was the tricky part to find out)
3. Connect the USB cable and the powercable.
4. The winXP should detect a new USB device. Make him happy - give him the rk28usb-new drivers to install.
5. Now the RKAndroidTool.exe should be able to detect the RKandroid USB device.
Ok, if you've got this far, now we need to re-flash it. For safety, let's do this with the default Archos 7HT update image (which can be downloaded from the Archos website)
I think that the RKAndroidTool.exe needs extracted files from update.img. For this, extract them using AFPTool.exe:
AFPTool.exe -unpack update.img .
(or use the extractupdate.bat)
Now, we can finish the reflashing:
6. Start RKAndroidTool.exe.
7. If the extracted files from update.img are placed in rockdev folder and in image subfolder, the RKAndroidTool.exe should find them automatically.
8. Execute. Make sure the device is plugged to AC, because the process takes some time. IF THE PROCESS STOPS UNEXPECTEDLY YOU GET A HIGH-TECH BRICK (or so everyone says, I didn't test it).
9. You should see the device responding and starting the update process. It will take some time, dont ruch it.
~20 seconds – copy firmware to device,
~30 seconds – device firmware installation,
~3-8 minutes - First boot
10. The Archos Tablet should ask you to recalibrate the screen, and load the OS.
That's it. Good luck!
==========================================
Sent from my iPhone using Tapatalk

INSTALLING CWM on ZOPO ZP900 LEADER

This method successfully installs the CWM on the phone. CWM version supplied by ZOPO does not work. Use the CWM posted in the second link
I am a still learning and not a developer !
Hi All ZOPO ZP900 Leader Owners,
This is a guide for Installing Clock Work Mod Recovery Image on ZOPO ZP900 Leader Phone. Most of the owners of this fantastic phone would have desperately tried like me to install CWM on this phone (some may have found success). ZOPO does gives an option to order the phone pre-rooted however they do not install CWM ....or for that matter there is no Stock Recovery on the phone !!!. Start the phone with Power + Volume Up button pressed and your presented with an image of sick Android lying down with a Red triangle coming out of his opened stomach :laugh:
DONT TRY TO USE ROM MANAGER APP TO INSTALL CWM, THIS WILL ONLY BRICK YOUR PHONE !
So after breaking my head for couple of days, searching the net, downloading stuff I have successfully installed CWM !
So here are the steps !.
What you need
1. ZOPO ZP900 Leader phone
2. Download Fully working English CWM from here http://www.4shared.com/file/16vuWyiU/recovery.html. The one posted in Zopo website does not work.
3. Download latest SP Flash Tool for MTK6577 from here http://www.4shared.com/zip/Xgc3G_hB/SP_Flash_Tool_v3122200.html
4. Download the latest Stock ICS ROM for ZP900 from Zopo website link http://www.4shared.com/rar/hGY2ahbu/MP_MT77_root_en_play_fix_zp900.html
5. Download MTK6577 Driver from Zopo website http://www.4shared.com/zip/YXlLFoLm/6577driver_install_3_steps.html
Installation Steps
1. Unzip and Install the USB drivers on your Windows PC using the MTK 6577 Driver Zip file. There will be 3 folders named First Step, Second Step & Third Step. Open First Step install the MTK driver MSI file. Post completion open Second Step, click on ClickInstall Driver, it will automatically install the USB driver. Press Exit after installation (Win 7 may give error that installation was incorrect, just ignore)
Repeat the same for folder Third Step
Connect your phone switched off and battery removed using USB cable. Windows will recognize and install the MTK drivers for your phone (any free COM ports) will be configured. Disconnect the phone. Put the battery back but do not switch on the phone
2.Extract the latest ROM folder from downloaded ICS ROM. You will get 2 folders
database
MP_MT77_h958_zp900_zwx_ics_20120912-155136_TSZ_PC
Open the second folder (MP_MT77***). This is the folder that has all the image files. You will find recovery.img file. This is original file. You can either rename it or keep a back up and delete it.
3. Copy the new CWM recovery.img file that you downloaded from ZOPO website in this folder. Rename it to be recovery.img
4. Extract and run SP flash Tool.exe (the one with Blue image icon)
5.Click on Options, USB Mode will be checked, DA Download All will be checked, in the sub options Speed will be Checked High Speed, Battery select With Battery. Come to the main Application window
6. Click on Scatter-loading button which is on the right side below Downloading Agent. A window will open. Browse to your extracted ICS ROM folder, click on folder MP_MT77****. By default you will have only one map file of name MT6577_Android_scatter_emmc. Select this
7. The flash tool will populate the Map file on the application window. You will see multiple Entries such as
PRELOADER
DSP_BL
MBR
etc etc. Each will have a check box which is by default checked.
8. UNCHECK all entries EXCEPT FOR "RECOVERY". Leave Recovery checked.
9. Now click on "Download" on the Application or press F9 on keyboard. A warning message will pop up. Press YES
10. You will see in the status bar below "Searching"
11. Connect your phone (switched off and with battery inserted) via the USB cable.
12. Flash tool will do its stuff. First a red progress bar, then a count down, a quick yellow progress bar and final window showing Green Circle.
If you get this the Congrats You have flashed CWM !
Check by unplugging the phone and re-starting it with Power+Volume Up button Pressed. The Phone will boot into CWM !.
Enjoy !
Warning - Please follow the instructions. Don't mess around with anything else. Not responsible if you do anything else and brick your device !
In case you get any other error on SP Flash Tool, then recheck your MTK driver installation. Try on another PC.
Now I hope this opens the door for many other things !
Additional Info -
Install PDAnet from here http://www.junefabrics.com/android/download.php or Snappea from www.snappea.com to make your device get recognized when connected to the computer. Install this with your phone switched on, this software installs the necessary drivers for the phone, post which you can use flash tool.

reserved
The CWM from taiwan101 for the 9300+ seems to be working fine. I was able to install .zip file from SD card. However the CWM is in Taiwanese, so if anyone can provide the CWM in English, thanks in advance
link for 9300+ CWM http://d01.megashares.com/dl/KicT315...M_Recovery.rar
UPDATE - Finally got a full working English CWM for ZOPO extracted from Mod ROM posted thanks to Kyrie1965. Tested and everything is working. Download from here http://www.4shared.com/file/16vuWyiU/recovery.html

vijayar said:
This method successfully installs the CWM on the phone. CWM as such works (able to navigate through the menus etc) but some of the function such as Install from ZIP, Backup etc, mount are not working, Gives an error Unable to Mount Sdcard !. Not sure if the issue is with CWM version supplied by ZOPO, need to try with other/older versions of CWM.
Please feel free to post links of CWM that works
I am a still learning and not a developer !
Hi All ZOPO ZP900 Leader Owners,
This is a guide for Installing Clock Work Mod Recovery Image on ZOPO ZP900 Leader Phone. Most of the owners of this fantastic phone would have desperately tried like me to install CWM on this phone (some may have found success). ZOPO does gives an option to order the phone pre-rooted however they do not install CWM ....or for that matter there is no Stock Recovery on the phone !!!. Start the phone with Power + Volume Up button pressed and your presented with an image of sick Android lying down with a Red triangle coming out of his opened stomach :laugh:
DONT TRY TO USE ROM MANAGER APP TO INSTALL CWM, THIS WILL ONLY BRICK YOUR PHONE !
So after breaking my head for couple of days, searching the net, downloading stuff I have successfully installed CWM !
So here are the steps !.
What you need
1. ZOPO ZP900 Leader phone
2. Download latest CWM from the link provided in Zopo Website http://www.4shared.com/file/lp0t5E1t/cmw-recovery.html
3. Download latest SP Flash Tool for MTK6577 from here http://www.4shared.com/zip/Xgc3G_hB/SP_Flash_Tool_v3122200.html
4. Download the latest Stock ICS ROM for ZP900 from Zopo website link http://www.4shared.com/rar/hGY2ahbu/MP_MT77_root_en_play_fix_zp900.html
5. Download MTK6577 Driver from Zopo website http://www.4shared.com/zip/YXlLFoLm/6577driver_install_3_steps.html
Installation Steps
1. Unzip and Install the USB drivers on your Windows PC using the MTK 6577 Driver Zip file. There will be 3 folders named First Step, Second Step & Third Step. Open First Step install the MTK driver MSI file. Post completion open Second Step, click on ClickInstall Driver, it will automatically install the USB driver. Press Exit after installation (Win 7 may give error that installation was incorrect, just ignore)
Repeat the same for folder Third Step
Connect your phone switched off and battery removed using USB cable. Windows will recognize and install the MTK drivers for your phone (any free COM ports) will be configured. Disconnect the phone. Put the battery back but do not switch on the phone
2.Extract the latest ROM folder from downloaded ICS ROM. You will get 2 folders
database
MP_MT77_h958_zp900_zwx_ics_20120912-155136_TSZ_PC
Open the second folder (MP_MT77***). This is the folder that has all the image files. You will find recovery.img file. This is original file. You can either rename it or keep a back up and delete it.
3. Copy the new CWM recovery.img file that you downloaded from ZOPO website in this folder. Rename it to be recovery.img
4. Extract and run SP flash Tool.exe (the one with Blue image icon)
5.Click on Options, USB Mode will be checked, DA Download All will be checked, in the sub options Speed will be Checked High Speed, Battery select With Battery. Come to the main Application window
6. Click on Scatter-loading button which is on the right side below Downloading Agent. A window will open. Browse to your extracted ICS ROM folder, click on folder MP_MT77****. By default you will have only one map file of name MT6577_Android_scatter_emmc. Select this
7. The flash tool will populate the Map file on the application window. You will see multiple Entries such as
PRELOADER
DSP_BL
MBR
etc etc. Each will have a check box which is by default checked.
8. UNCHECK all entries EXCEPT FOR "RECOVERY". Leave Recovery checked.
9. Now click on "Download" on the Application or press F9 on keyboard. A warning message will pop up. Press YES
10. You will see in the status bar below "Searching"
11. Connect your phone (switched off and with battery inserted) via the USB cable.
12. Flash tool will do its stuff. First a red progress bar, then a count down, a quick yellow progress bar and final window showing Green Circle.
If you get this the Congrats You have flashed CWM !
Check by unplugging the phone and re-starting it with Power+Volume Up button Pressed. The Phone will boot into CWM !.
Enjoy !
Warning - Please follow the instructions. Don't mess around with anything else. Not responsible if you do anything else and brick your device !
In case you get any other error on SP Flash Tool, then recheck your MTK driver installation. Try on another PC.
Now I hope this opens the door for many other things !
Click to expand...
Click to collapse
hey will this work on hero 9300+ ,512mb ram .
i have ordered one and will soon arrive.
will try to make some custom roms.

B rom error:
hi there does anyone has flash the zopo900 leader and got the message B ROM ERROR: S_COM_PORT_OPEN_FAIL (1013)
It wont letme flash the phone driver seems working fine but it said "single usb port" and the port assing it. please help!

Hi Vijay,
What if i dont follow the step 8 (uncheck everything except recovery). Does it cause any issue?
I am running win 7 x64 and when i run the flash tool it says searching only after i click the download

help
hey i have hero 9300+ 512mb ram
i have no network issue plz help me!:crying:

miraguilar1 said:
hi there does anyone has flash the zopo900 leader and got the message B ROM ERROR: S_COM_PORT_OPEN_FAIL (1013)
It wont letme flash the phone driver seems working fine but it said "single usb port" and the port assing it. please help!
Click to expand...
Click to collapse
Check your device drivers USB driver has not been installed properly. I faced this issue and after multiple attempts of reinstall of USB drivers the flash tool started working properly
Also you can try installing PDAnet from here http://www.junefabrics.com/android/download.php
Install this with your phone switched on, this software installs the necessary drivers for the phone, post which you can use flash tool.
Note Connect the phone to flash tool first without battery, in options select with battery, press download after selecting the required file, when it says searching unplug the phone put battery back, dont switch on, plus back the usb. The flash tool should load the required file.

senlakshman said:
Hi Vijay,
What if i dont follow the step 8 (uncheck everything except recovery). Does it cause any issue?
I am running win 7 x64 and when i run the flash tool it says searching only after i click the download
Click to expand...
Click to collapse
It will flash the entire ROM again. My guide was specifically for flashing only the CWM and not the entire ROM. I wanted to keep the Stock rom intact as it came from ZOPO.
Word of caution, I am yet top try flashing the complete ROM so if you are trying ensure that your have taken a backup via CWM (if already flashed) of your existing full working ROM before attempting anything. Also flash only ZOPO Stock or customised ROMs,

From where did you bought this mobile?
Does the imei start from 355,889,3535
Is it ips 1gb ram .
Sent from my GT-I9100 using xda premium

Anyone having problem with drivers can follow this http://www.youtube.com/watch?v=Rfemoi6Aizw
complete flashing process
Sent from my GT-I9100 using xda premium

vijayar said:
It will flash the entire ROM again. My guide was specifically for flashing only the CWM and not the entire ROM. I wanted to keep the Stock rom intact as it came from ZOPO.
Word of caution, I am yet top try flashing the complete ROM so if you are trying ensure that your have taken a backup via CWM (if already flashed) of your existing full working ROM before attempting anything. Also flash only ZOPO Stock or customised ROMs,
Click to expand...
Click to collapse
I have installed the drivers, while the phone is on using pdanet and i powered off and ran the flash tool first without battery (with battery option) and put the battery back in. but i got message stating please insert usb and Flashtool have this alert.
Not sure, where i am missing the steps

plz also have a look at previous posts u will get your answer.

senlakshman said:
I have installed the drivers, while the phone is on using pdanet and i powered off and ran the flash tool first without battery (with battery option) and put the battery back in. but i got message stating please insert usb and Flashtool have this alert.
Not sure, where i am missing the steps
Click to expand...
Click to collapse
i too was having this problem but i tried the MTK6575 DRIVER and it worked maybe give it a try

Hey guys, I want to try this on my hero 9300+.
Is it safe?

Working
bhargav1991 said:
hey will this work on hero 9300+ ,512mb ram .
i have ordered one and will soon arrive.
will try to make some custom roms.
Click to expand...
Click to collapse
Confirmed working on 9300+
Follow the tutorial exactly as written.
---------- Post added at 10:38 PM ---------- Previous post was at 10:28 PM ----------
Israeleet said:
Hey guys, I want to try this on my hero 9300+.
Is it safe?
Click to expand...
Click to collapse
This is a copy of cwm with the specific support for the MTK6577 used by the 9300+
So yes it safe.
---------- Post added at 10:46 PM ---------- Previous post was at 10:38 PM ----------
bhargav1991 said:
hey i have hero 9300+ 512mb ram
i have no network issue plz help me!:crying:
Click to expand...
Click to collapse
Make sure you removed the battery long enough from your phone.
You may also have to reboot your pc a couple of times.

Wtf .
I am talking about the no service issue,it doesn't have any relation
With battery or pc :what:
Anyways its an imei issue.
Sent from my GT-I9100 using xda premium

vattmann said:
i too was having this problem but i tried the MTK6575 DRIVER and it worked maybe give it a try
Click to expand...
Click to collapse
Yessss , it did worked by using the MTK6575 driver :good:

bhargav1991 said:
Wtf .
I am talking about the no service issue,it doesn't have any relation
With battery or pc :what:
Anyways its an imei issue.
Sent from my GT-I9100 using xda premium
Click to expand...
Click to collapse
YTF
This is the CWM forum.

Has anyone tried tw5 launcher on this ?
Sent from my GT-I9100 using xda premium

bhargav1991 said:
Anyone having problem with drivers can follow this http://www.youtube.com/watch?v=Rfemoi6Aizw
complete flashing process
Sent from my GT-I9100 using xda premium
Click to expand...
Click to collapse
Hello bhargav1991, i got some questions:
1. I've buy zp900 but it will arrive next week. In the video you posted there is a guide how to flash the official Zopo z900 latest stock ROM but in this way you get the latest rom + root but no ClockWorkMod Recovery installed ?¿¿
2. My intention as i done with my old..HTC Desire HD is flashing ClockWorkMod Recovery and install the latest Zp 900 stock ROM + ROOT. So following the 1st post and once all steps are done one by one, will I get the same rom that come installed ?¿ but non root ?¿
I need to download the latest ZOPO ROM .zip and then install it from ClockWorkMod and finally i will get the latest ROM + ROOT ¿?
Could you please help me
Thank you so much in advance guys ¡¡
:good:

[Tutorial] Revive dead Karbonn A9+/CM Flare after JB update

Follow this guide carefully and you can revive your dead Karbonn A9+/ CM Flare after Jelly Bean Upgrade.
Tools Needed:
Dead Phone (When u connect to PC it should install Qualcomm HS-USB QD Loader 9008 Driver) Link
QPST.2.7.399 Link
Flare Revival kit Link
PC with 32 bit Windows (XP/Vista/7/8) (64bit casus problem in QPST installation)
Credit goes to jhanra for the tutorial as well as CWM 6.0.1.1 for JB ROM . :good:

Procedure
Connect ur phone to PC and let the driver install
Install QPST
Open QPST Configuration (in Win XP compatibility mode) ->Add new port -> Select the com port of your device ->exit.
Go to Start -> All Programs -> QPST eMMC Software Download open the tool -> Check program boot loaders -> Browse for the device com port
Extract Flare Revival Kit on desktop
If Phone is not detected , Click Browse
In flash programmer file name type MPRG8X25.hex -> in Boot Image type 8X25_msimage.mbn in SPC ->000000
Click Load XML def and browse for rawprogram0.xml in Flare Revival Kit
Click Load Patch def and browse for patch0.xml
Check the search path 2 and browse for the folder flare repair files
Now click download, wait for the download to finish (it never finish but it also detects for a new driver, and that’s important) and it will search for the new hardware found, install the driver
From here you can updating your rom to jelly bean using this tutorial Link

Guys, anyone encountering "Cookie (if present) not received" error after clicking on Download button?
My Karbonn A9+ as successfully updated to jelly bean, which was working flawlessly for 3 days. But suddenly it died while my charging my phone.. The phone could not be turned on, no fastloader or entry download mode.... However when connected to PC it was being detected as Qualcomm HS-USB QD Loader 9008. I tried this tutorial but am facing cookie not received error.
Since my phone died suddenly, not during any update firmware process... I suspect this could be case of Sudden Death Syndrome (SDS) which means my eMMC flash (internal storage) got corrupted and is not being able to recoginized by QPST tool.
Has anyone faced this problem?

kornholic said:
Guys, anyone encountering "Cookie (if present) not received" error after clicking on Download button?
My Karbonn A9+ as successfully updated to jelly bean, which was working flawlessly for 3 days. But suddenly it died while my charging my phone.. The phone could not be turned on, no fastloader or entry download mode.... However when connected to PC it was being detected as Qualcomm HS-USB QD Loader 9008. I tried this tutorial but am facing cookie not received error.
Since my phone died suddenly, not during any update firmware process... I suspect this could be case of Sudden Death Syndrome (SDS) which means my eMMC flash (internal storage) got corrupted and is not being able to recoginized by QPST tool.
Has anyone faced this problem?
Click to expand...
Click to collapse
Please state your OS Win XP or 7. Try using 32 bit win XP PC.

arunmcops said:
Please state your OS Win XP or 7. Try using 32 bit win XP PC.
Click to expand...
Click to collapse
My os is windows 7 32 bit.. i tried running emmc downloader with windows xp compatibility mode also. same problem.

kornholic said:
My os is windows 7 32 bit.. i tried running emmc downloader with windows xp compatibility mode also. same problem.
Click to expand...
Click to collapse
QPST caused me problems with Win 7. I used win XP.

arunmcops said:
QPST caused me problems with Win 7. I used win XP.
Click to expand...
Click to collapse
Tried it on Win XP... same cookie(if present) not received error showing..

can we use vmplayer for the win xp or other virtual soever instead? i use win 8 64 bit that's why it won't able me to download and shows me the message that the cookie (if present) is not received. :angel::angel::angel:

Some from a chinese forum was able to fix the cookie problem through QFPROM Fuse..
http:// lepad.it168.com/thread-2920933-1-1.html
(its in chinese)
What does it mean?

kornholic said:
Some from a chinese forum was able to fix the cookie problem through QFPROM Fuse..
http:// lepad.it168.com/thread-2920933-1-1.html
(its in chinese)
What does it mean?
Click to expand...
Click to collapse
Only explanation given is that This problem is related to specific PC.

arunmcops said:
Only explanation given is that This problem is related to specific PC.
Click to expand...
Click to collapse
Yes the person in one post first said the problem is due to PC and driver combination. However, in later post has also said:
"i am still stuck in download mode. i was able to programm the bootloader, as i mentioned before by using QFPROM Fuse, everything else leads to errors. only one little detail changed -> when i press the power button it vibrates shortly.when i try to porgram the mmc device i always get no response from the phone."
Some of the points to ponder are:
1. He said he was able to program bootloader using qfprom fuse.
(How did he program bootloader through qfprom fuse, what does this mean?)
2. When power button pressed, there is vibration...
(On my device there is no response when pressed on power on.)
3. However he later said when he tries to program mm, he gets no response.
(He has not said he gets cookie error, just not response... could be anything)

one of the moderator of cherry flare group at facebook was able to revive phone from cookie error.
check http://www.youtube.com/watch?v=qHQIIsqV1Zw

i just found out that you can restore your phone too by using roadkill, if you had written the backup of the image of your phone lately. :angel:

heyyanyan said:
i just found out that you can restore your phone too by using roadkill, if you had written the backup of the image of your phone lately. :angel:
Click to expand...
Click to collapse
yes, if you could access entry qpst download mode (vol down + power)... however if you are hard bricked... you would not be able to access that plus your phone would not turn on in any manner.

in my case, my phone didn't turn on no matter what i do. but if i connect my phone to the pc, it shows the qualcomm hs-usb something that can be read by roadkill.

heyyanyan said:
in my case, my phone didn't turn on no matter what i do. but if i connect my phone to the pc, it shows the qualcomm hs-usb something that can be read by roadkill.
Click to expand...
Click to collapse
did you manage to fix your phone?? ......................................................

arunmcops said:
Connect ur phone to PC and let the driver install
Install QPST
Open QPST Configuration (in Win XP compatibility mode) ->Add new port -> Select the com port of your device ->exit.
Go to Start -> All Programs -> QPST eMMC Software Download open the tool -> Check program boot loaders -> Browse for the device com port
Extract Flare Revival Kit on desktop
If Phone is not detected , Click Browse
In flash programmer file name type MPRG8X25.hex -> in Boot Image type 8X25_msimage.mbn in SPC ->000000
Click Load XML def and browse for rawprogram0.xml in Flare Revival Kit
Click Load Patch def and browse for patch0.xml
Check the search path 2 and browse for the folder flare repair files
Now click download, wait for the download to finish (it never finish but it also detects for a new driver, and that’s important) and it will search for the new hardware found, install the driver
From here you can updating your rom to jelly bean using this tutorial Link
Click to expand...
Click to collapse
!!!

!? I just Ported CWM 6.0.1.1 to CM Flare Jelly bean (for JELLY BEAN ONLY)!! !!!! I Already test it with my own 3pcs CM FLARE phone with no problem! In porting this CWM my 2 phone died porting this CWM but I recover it WITH THIS METHOD you posted!!!!!!!!!!!!!!
FLash this with AIO FLASHER
check recovery erase then flash
View attachment 2089726
theres nothing it can do if you try it? it cannot mess your phone!
!!!

this is the full tutorial for this! View attachment 2089809,
and this is the file for this case!
h ttp://www.4shared.co m/rar/rzVTMMxY/flare_repair_files.html
after this you can flash BP firmware in this! follow the tut in flashing BP Firmware and so on
to upgrading in jelly bean BY ARUNMCOPS! here ht tp://forum. xda-developers.com/ showthread.php?t=2330823
the original thread is here ht tp://www.pinoy den.com.ph/inde x.php?topic=274677.0
Note: just erase the spaces of the link!
you can try the steps on my tut but DO THIS AT YOUR OWN RISK!!!
!!!!!!
[email protected]@@
[MENTION=1065870 [user=1879310]@@@@[/user][/MENTION]
@@@

kornholic
@@@????

How to install a Custom ROM on the Trio Stealth Pro 7c

DO THIS AT YOUR OWN RISK. YOU COULD PERMANENTLY DAMAGE YOUR DEVICE. READ ALL DIRECTIONS BEFORE ATTEMPTING.
These tablets are an LY-F1 clone. So most of the stuff that is compatible with an ly-f1 will work for you.
The model I am referring to and have personal experience with is the following: Trio Stealth Pro 7c
The Trio already comes rooted. I accidentally un-rooted mine AND I ended up with the 0.00 internal storage error. It would not let me download or install apps already on my SD card. To install a new (custom) ROM you can follow this quick guide I put together.
First...
Things you will need to Download;
CWM Recovery for the Trio Stealth Pro 7c : CWM Recovery 6.0.1.2 for Allwinner A10 LY-F1/TREQ Tablets
Custom ROM for the Trio Stealth Pro 7c : Choco Ice Cream 4.0 BETA1 for Allwinner A10 LY-F1/TREQ
32 or 64-bit Windows ADB Drivers : Windows ADB Drivers for Trio Stealth Pro 7c
ADB needs to be downloaded and installed/setup via the Android SDK found here : Android SDK Download
1.) Download CWM Recovery
2.) After your download is finished go ahead and extract the contents to the SD card. I connected to my PC and put the extracted files (there are 3 files) on both the internal storage as well as the removable micro-SD just to be safe.
3.) Download Choco Ice Cream 4.0 BETA1 Download Choco Ice Cream 4.0 BETA1
4.) After the ROM finishes downloading DO NOT extract; just copy the whole .zip file directly to the Micro-SD Card as-is.
5.) Connect your Trio to your Windows PC with a USB cable. Make sure you go to settings/Developer Options/and turn on USB Debugging. I had to open device manager and manually install the ADB Drivers for Trio Stealth Pro 7c. You can check to see if the drivers are installed by opening a command prompt on your computer. You would do this by going to start and typing CMD into the search bar. Or you can click on Run and type CMD into the box. This should open your command prompt. Enter each line one at a time, pressing enter after each line:
cd/
cd androidsdk/platform-tools (some of you may have to type just "tools' depending on which version you have)
adb devices
After hitting enter you should see your device's serial number. This shows that your device is connected and was found. If you do not see your device serial number either you don't have the correct drivers for your device or you did not enable usb debugging mode.
6.) Now we're going to start the adb shell by typing the following, again, pressing ENTER after each line of text.
cd\
cd androidsdk\platform-tools
adb shell
You should now see one of the following symbols:
# or $
Now type the following, again, pressing ENTER after each line of text
cd /mnt/sdcard
sh install-recovery.sh
sh reboot-recovery.sh
After pressing enter, you will see your tablet reboot into recovery mode. You can use the volume buttons to move up and down and use the power button to select. To get back into Recovery Mode if you reboot out of it or your tablet turns off; go ahead and turn your Trio completely off. Once it is shut down press the center of the volume button until the WHOLE thing is pushed in. Do this WHILE holding down the power button. Keep it held for a few seconds until you see the the screen come back on. Once you see it, you can let go and it will reboot into recovery mode.
7.) From Recovery mode:
MAKE A FULL BACK-UP FIRST. DON'T IGNORE THIS STEP!!! IT MIGHT JUST SAVE YOUR DEVICE ONE DAY!!! When the backup gets finished go back and then:
SELECT: INSTALL ZIP FROM SD CARD. (press the power button once to select it).
If you placed the ROM on the micro SD-card then you should select 'Choose zip from sd card' if you placed the ROM on your internal SD-card you should select: 'Choose zip from internal sd card'. Now find where you placed the ROM/download. Use the volume buttons to scroll up and down. Once you find it, select it with the power button. Scroll down until you see 'Install choco ice cream 4.0beta1_LYF1.zip'. Select this with the power button.
8.) It should now start to install. This will take maybe 3 minutes tops. Just be patient. When it's done, wipe the data and the cache. (it was one of the options listed when you first start recovery mode)
9.) SELECT: GO BACK; then choose REBOOT or REBOOT YOUR DEVICE or whatever and wait for the device to finish restarting. It takes several minutes to finish booting up; be patient; it will get done sooner or later.
10.) Your Finished
Here are some useful links for more Custom ROM's and other stuff you might need or find helpful:
XDA Thread for [ROM][Allwinner A10] Choco Ice Cream 4.0 BETA1 for LY-F1/TREQ
XDA Thread for CWM Recovery 6.0.1.2 for Allwinner A10 LY-F1/TREQ Tablets
XDA Thread for [rom] Unofficial CyanogenMod 9 for many AllWinner A10 tablets
XDA Thread for [rom] Unofficial AOKP for many AllWinner A10 tablets
XDA Thread for [ROM][PORT]CM9/CM10 for LY-F1/AlldroSpeed-UPDATED 13.09.2012
Good Luck...

will this work on Trio Stealth G4 7'' Tablet?
or at least the custom recovery and custom rom part?
im already rooted
just cant update binaries for some odd reason, some kingoroot thing, but its rooted and root works
---------- Post added at 01:14 PM ---------- Previous post was at 12:56 PM ----------

trio-stealth g4 7
How do you rooted the trio-stealth g4 7?

Tried safestrap, backup failed
I installed safestrap with your instructions. adb was not able to be downloaded for my device given the link you provided, but I had another version that I used from Android Multitools to perform the safestrap install. Only problem is now that I've installed safestrap, it boots into recovery just fine. However, that's the only thing I can boot to. I can't boot normally, and my backup using safestrap failed at /system (error was something similar to "could not mount /system!".
Any suggestions? I would like to be able to boot normally and backup fully if I can, I'm kinda worried about reflashing into the custom ROM and not being able to recover.

UPDATE:
This safestrap installation did not work for my stealth trio 7c A13. It actually prevented my device from booting, and when trying to install the choco rom, my device not only bricked but my SD card was corrupted as well. Not saying it's the ops fault at all, I know the risks when performing tasks such as these. I just want everyone to be aware.
I was able to restore my brick using the livesuite software and flashing with an image of 4.1 that I found from a different site. If anyone would like more info, ill be happy to provide it. My new rom is Google play good to go, so im happy. :thumbup:
Sent from my SCH-i605 through space and time
Brought forth to your face by the XDA Developer app

Hellstorm32 said:
UPDATE:
This safestrap installation did not work for my stealth trio 7c A13. It actually prevented my device from booting, and when trying to install the choco rom, my device not only bricked but my SD card was corrupted as well. Not saying it's the ops fault at all, I know the risks when performing tasks such as these. I just want everyone to be aware.
I was able to restore my brick using the livesuite software and flashing with an image of 4.1 that I found from a different site. If anyone would like more info, ill be happy to provide it. My new rom is Google play good to go, so im happy. :thumbup:
Sent from my SCH-i605 through space and time
Brought forth to your face by the XDA Developer app
Click to expand...
Click to collapse
I have a trio g4 7" mst-741 model will it work for me?

I don't know about a g4, I have no experience with those. Sorry

how long dose it take i put it on a trio stealth pro metal in hopes of geting good update

[STOCK ROM][TOOL][ALCATEL] One touch tab 7 (T15)

Probably, if you are here then your alcatel touch is running with the Prestigio 7.0 multipad stock rom (PM3970), with no wireless and no accelerometer. Finally, I got my hands on the stock rom for the Alcatel one touch (T15). I would lay out the instructions that finally got this tab to work.
I stumbled upon it on an arabic forum called gsm-flash.com, tested it and thought of sharing it with you:
Download the AmLogic USB burning tool attached
Run the AmLogic app with administrative privileges
Power off your device
Connect the device using the USB cable
Press Power & Vol + until you see that your device is connected on Port 1 of the app
If all is good, goto step 10,if it didn’t then you need the drivers, proceed to step 8
Locate the Amlogic tool folder and then select the AmLogicUSBurningDrive folder
Select the win7 folder, locate the right installer and run it as admin
Go back to 3
In the Amlogic app, select File, then Import, locate the Alcatel-tab 7 archive you downloaded from below, pass it as it is, don’t UNZIP it
Optionally, you can pass the Serial number of the device if you want,and the CU reference in this case, T105-3AALEU1, I didn’t pass either of them, but the CU reference was added under the model number in the about tablet
Click Start
Wait for the process to complete
If successful proceed to step 15, otherwise, goto step 3 and repeat, which was what happened to me, I repeated it 3 times
Finally, the phone reboots with Alcatel One Touch logo, it will take some time
I was impatient, restarted it, and waited, then rebooted into recovery by using Power & Vol +, and made a factory reset
And Voila.Congrats on restoring your device
I apologize, don't have the right to post external URLS at the moment. Copy and paste without the quotes.
"https://drive.google.com/file/d/1s0wh5NZCNpxG2j7-QneQGYbeB30MlkJr/view?usp=sharing"
"https://drive.google.com/file/d/1CRdXmZ7uQ1LSpgWV5hI-7-3yBgltF7XF/view?usp=sharing"
Hope this helps anyone.
Regards,