Database Info

Recover from soft brick

Hello everybudy here is a guide to recover from soft brick(I ave only tested it on S7500 not other)
So do it at ur own risk
First download odin3 v1.85
Download stock firmware for ur cont
Extract both in a particular folder
Open odin
Go to Download mode in ur phone and press volume up
Connect ur phone to pc
If odin shows a yellow mark then u are ready to proceed
Mark PDA & and selct file
Click start in odin
Keep patience
After process is over odin will show pass
Now ur phone will reboot
(DO NOT REMOVE USB CABLE TILL ITS REBOOTED PROPELY)
Complete the setup
Now again switch off mobile as as the process has not been completed yet
Go to recovery mode (this time it would be stock recovery not cwm)
In recovery mode select wipe data factory reset and wipe cache partition
Reboot.
Now u are done!!
HIT THANKS IF I HELPED
Odin-http:// www.androidlegend.com/dl/Odin3_v1.85.zip
Stock firmware(pda)- http://www.tsar3000.com/Joomla/inde...ace-plus-firmwares&catid=55:samsung&Itemid=82
Sent from my GT-S7500

whats new in this there is a sticky in which hole process is shown correctly
and 1 thing -
you should edit PDA ...it is different for different countries
you provided the firmware which is not for Indian users
http://www.sammobile.com/firmwares/
this is were you can get firmware for your own country !!

Ok i have edited pda and u can check the link
Also, I am a Indian and have tried this and its almost same
Only we have to change the language
Thanks any way
Sent from my GT-S7500

I had searched but it was not in q n ans. So i put it in this section. I dont know about stickies as i am new to this
Sent from my GT-S7500

There has also a type of soft brick where you will not be able to access download mode. Then odin will not work
then use USB jig. See http://www.xda-developers.com/android/need-a-samsung-usb-jig-build-your-own/

Ya i know
Sent from my GT-S7500

[email protected] said:
Ya i know
Sent from my GT-S7500
Click to expand...
Click to collapse
I know that you know. It was not mentioned so I mentioned it.

Itz showing fail please help asap!!!!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> S7500DDMF2_S7500ODDMF1_S7500DDME1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> system.img.ext4
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
i tried its coming failed,i tried downloading odin and firmware again from sam mobile, evn removed kies still the same please help asap!!

Ashmit Poojari said:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> S7500DDMF2_S7500ODDMF1_S7500DDME1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> system.img.ext4
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
i tried its coming failed,i tried downloading odin and firmware again from sam mobile, evn removed kies still the same please help asap!!
Click to expand...
Click to collapse
Keep Odin open and change USB ports, remount the PDA & flash. Hope this helped, worked for me

[Help] Galaxy Note 10.1, 2012 edition not powering on at all. Stock

I have a stock Galaxy note 10.1 NT8010, i hadnt used it in a few days. Went to power on and wouldnt boot. Thinking it was dead i charged it for a few hours and still wouldnt turn on. The power brick is fine, i bought a new stock cable, just waiting for that to come and rule out the cable. But its stock android no rooting or anything.
Any ideas?

Battery shows as charging ??
Odin mode ??? or Recovery Mode ???

JJEgan said:
Battery shows as charging ??
Odin mode ??? or Recovery Mode ???
Click to expand...
Click to collapse
Thanks for replying. Screen is completely dead not even a backlight.
For odin to work would i have to have it rooted previously?

For odin to work would i have to have it rooted previously?
No it does not require root .

JJEgan said:
For odin to work would i have to have it rooted previously?
No it does not require root .
Click to expand...
Click to collapse
Ok, so the pc is not picking it up at all.
I took off the back cover, disconnected the battery and reconnected.
Plugged it into the charger while the cover was still off. On the top left its making a "ti-ti-ti" noise while plugged into power.
Im guessing the motherboard/battery/screen are/is dead. Well one of the 3.
Any ideas?

amsung Tab GT-N8010 Rom doesn't Install, PIT issue, Flashing Screen, do not turn ON
I have Samsung Tab GT-N8010
When I try to turn on, its screen flashing White for half second and then Black and Continuosly till the Battery End.
I try to Install ROM 4.4.2 with ODIN 3.10.7 and get this error
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1100)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004>
<ID:0/004> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
I tried different PIT files including 3 different N8010.pit and 8013.pit and 8020.pit
but the issue remaining same
I read all the google search including Russian websites at-least but I couldn't find the issue
I have original cable
EMMC Corrupted may be
I need Solution plz help if anyone can

rehansonu said:
amsung Tab GT-N8010 Rom doesn't Install, PIT issue, Flashing Screen, do not turn ON
I have Samsung Tab GT-N8010
When I try to turn on, its screen flashing White for half second and then Black and Continuosly till the Battery End.
I try to Install ROM 4.4.2 with ODIN 3.10.7 and get this error
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1100)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004>
<ID:0/004> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
I tried different PIT files including 3 different N8010.pit and 8013.pit and 8020.pit
but the issue remaining same
I read all the google search including Russian websites at-least but I couldn't find the issue
I have original cable
EMMC Corrupted may be
I need Solution plz help if anyone can
Click to expand...
Click to collapse
same problem here! need help!!!!!

rehansonu said:
amsung Tab GT-N8010 Rom doesn't Install, PIT issue, Flashing Screen, do not turn ON
I have Samsung Tab GT-N8010
When I try to turn on, its screen flashing White for half second and then Black and Continuosly till the Battery End.
I try to Install ROM 4.4.2 with ODIN 3.10.7 and get this error
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1100)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004>
<ID:0/004> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
I tried different PIT files including 3 different N8010.pit and 8013.pit and 8020.pit
but the issue remaining same
I read all the google search including Russian websites at-least but I couldn't find the issue
I have original cable
EMMC Corrupted may be
I need Solution plz help if anyone can
Click to expand...
Click to collapse
Same problem here!!!! Service center says Motherboard replacement!!! Please help.

Samsung Tab GT-N8010 Rom doesn't Install, PIT issue, Flashing Screen, do not turn ON

I have Samsung Tab GT-N8010
When I try to turn on, its screen flashing White for half second and then Black and Continuosly till the Battery End.
I try to Install ROM 4.4.2 & 4.1 also with ODIN 3.10.7 and get this error
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1100)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004>
<ID:0/004> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
I tried different PIT files including 3 different N8010.pit and 8013.pit and 8020.pit
but the issue remaining same
I read all the google search including Russian websites at-least but I couldn't find the issue
I have original cable
(Internal Partition Corrupted I think (EMMC Error))

I am waiting for useful solution. Anyone can help me here?

rehansonu said:
I am waiting for useful solution. Anyone can help me here?
Click to expand...
Click to collapse
same problem here, have you fix it?

rehansonu said:
I am waiting for useful solution. Anyone can help me here?
Click to expand...
Click to collapse
Have you odin the firmware and apply the pit at the same time?, Plus you shouldn't use pits for other models (ie 8013,8020)

How much storage do you have?

Looking for help with my bricked Note 5 Sprint

https://forum.xda-developers.com/not...3#post65243282
This is a post I made previously about a year ago. Yesterday I picked the phone back up and tried to figure things out again. A year ago I never really got anywhere. I have never flashed anything or used Odin.
This is how far I got yesterday and I am looking for some advice. I tried flashing a stock ROM via Odin because the guy who commented said I should try that. So yesterday I did.
This is the site I followed.
https://devs-lab.com/how-to-unbrick-...xy-note-5.html
I downloaded Odin3 v3.10.0. I then downloaded Samsung Keys to install the usb driver but it wouldn't even detect the phone. That didn't work so I went here to get the drivers installed.http://www.samsung.com/us/support/ow...y-note5-sprint
I then downloaded the stock Rom the website had on it that matched the Product name SM-n920P that comes up when the phone is in download mode.
http://stockroms.net/file/GalaxyNote...T2BPC3_SPR.zip
After that finally downloaded I extracted the Rom to the desktop. I opened Odid clicked on AP like the website said and clicked Start. I then received a Nand Write Start error and nothing happens.
Here is a picture of what Odin looks like when I tried to do it.
http://i.imgur.com/31hTrq3.jpg
Thank you for your help and if I sound like a moron I am sorry I am not very experience when it comes to this.

- When you add the tar.md5 file don't remove the .md5, it will verify the file integrity and may take a few minutes to do so.
- You must be in download mode to use Odin. When you attach the phone, one of the squares should light up telling you which com port is attached.
- You might be blocked from flashing older firmware, PC3 is rather old. Try a newer firmware. All firmwares are available in my repository:
https://www.mediafire.com/folder/byye3kocz6nn4/Stock_Roms_Note_5
Files are zipped. Unzip and place the tar.md5 in AP.

tdunham said:
- When you add the tar.md5 file don't remove the .md5, it will verify the file integrity and may take a few minutes to do so.
- You must be in download mode to use Odin. When you attach the phone, one of the squares should light up telling you which com port is attached.
- You might be blocked from flashing older firmware, PC3 is rather old. Try a newer firmware. All firmwares are available in my repository:
https://www.mediafire.com/folder/byye3kocz6nn4/Stock_Roms_Note_5
Files are zipped. Unzip and place the tar.md5 in AP.
Click to expand...
Click to collapse
I forgot to mention I did have the phone in download mode when I previously attempted to download that file on Odin.
I think I just added the file I didn't know the .md5 got removed. Should I add it a different way to make sure it isn't removed.
Which firmware in the repository should I use? They all look like the same thing to me. Except for the one at the end that says full wipe.
Should I just download one of the newer firmwares on that list and put the phone into download mode and give it another go? If so which file and how?
Again thank you for your help and I apologize if you have already told me something and I just didn't understand.

Don't mess with file extension.
They aren't listed chronologically but alphabetically, pd is newer than pc3 and so on. Try pd2 first maybe.

Alright thanks bro I appreciate all your help and understanding. I will try the 2nd one like you said. It says it will take 2 hours to download so I can use it on Odin and give it a try. I will post an update later crossing my fingers this works.

tdunham said:
Don't mess with file extension.
They aren't listed chronologically but alphabetically, pd is newer than pc3 and so on. Try pd2 first maybe.
Click to expand...
Click to collapse
Here was was Odin said when I tried.
<ID:0/005> Removed!!
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N920PVPU2BPD2_N920PSPT2BPD2_N920PVPU2BPD2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
Ok I try the pd2 and flashed it on Odin the device was in download mode but I didn't have any success . What should I try next?

Pk1 or pl1

tdunham said:
Pk1 or pl1
Click to expand...
Click to collapse
Alright so I tried Pl1 on Odin and I tried Pk1 but neither seemed to work here are the Odin scripts I got from them. I'm not sure what to try next, what do you think I should try?
PL1
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N920PVPS3BPL1_N920PSPT3BPL1_N920PVPS3BPL1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
PK1
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N920PVPS3BPL1_N920PSPT3BPL1_N920PVPS3BPL1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..

try a different cable, try the cable in a different usb port or try it on another computer too if that doesn't work.
You could also try taking it to the sprint store and having them flash it for you. I think they might charge a fee for that, so ask first.

tdunham said:
try a different cable, try the cable in a different usb port or try it on another computer too if that doesn't work.
You could also try taking it to the sprint store and having them flash it for you. I think they might charge a fee for that, so ask first.
Click to expand...
Click to collapse
Alright I tried them all again with a new cord and a different port. When my cousin gave me the phone I don't think the contract was left in a good standing. Would providing them with the phone show up under his name and possibly make them not want to do it? Also any idea on how much they may charge if you had to guess? I'm really strapped for cash right now and am trying to fix this phone for my dad because his phone is messing up and we can't afford another phone. Do you think I should try to flash some different ones off the list you provided and give it a shot? I was hoping to fix it at home because I'm not sure what Sprint will say when I go up there. Here are the retries. Thanks again for all the help, sorry it keeps being such a hassle.
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N920PVPS3BPK1_N920PSPT3BPK1_N920PVPS3BPK1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Added!!
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<OSM> All threads completed. (succeed 0 / failed 1)
<OSM> All threads completed. (succeed 0 / failed 0)
<OSM> All threads completed. (succeed 0 / failed 0)
<ID:0/006> Removed!!
<ID:0/004> Added!!
<ID:0/004> Removed!!
<ID:0/005> Added!!
<ID:0/005> Removed!!
<ID:0/007> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N920PVPS3BPK1_N920PSPT3BPK1_N920PVPS3BPK1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/007> Removed!!
<ID:0/007> Added!!
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N920PVPS3BPL1_N920PSPT3BPL1_N920PVPS3BPL1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Added!!
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<OSM> Please wait..
<OSM> N920PVPU2BPC3_N920PSPT2BPC3_N920PVPU2BPC3_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Added!!
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N920PVPS3BPJ2_N920PSPT3BPJ2_N920PVPS3BPJ2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Added!!
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N920PVPU2BPD2_N920PSPT2BPD2_N920PVPU2BPD2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Added!!
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)

Bingo308 said:
Alright I tried them all again with a new cord and a different port. When my cousin gave me the phone I don't think the contract was left in a good standing. Would providing them with the phone show up under his name and possibly make them not want to do it? Also any idea on how much they may charge if you had to guess? I'm really strapped for cash right now and am trying to fix this phone for my dad because his phone is messing up and we can't afford another phone. Do you think I should try to flash some different ones off the list you provided and give it a shot? I was hoping to fix it at home because I'm not sure what Sprint will say when I go up there. Here are the retries. Thanks again for all the help, sorry it keeps being such a hassle.
Click to expand...
Click to collapse
I don't know what Sprint charges, it used to be $35. They may not look at it if there is no active account for it anyway.
Maybe check with some local cell third party phone shops and ask what they would charge to flash the factory image back to the phone.

I suggest you to change usb cable, reinstall drivers on pc, use a different usb port, if still same try on a different computer. It looks like phone isn't in download mode in logs from odin

matthew2man said:
I suggest you to change usb cable, reinstall drivers on pc, use a different usb port, if still same try on a different computer. It looks like phone isn't in download mode in logs from odin
Click to expand...
Click to collapse
I think it's been in download mode it says downloading and do not turn off target. Do you think maybe I have a bad version of Odin or installed the wrong drivers. Do these drivers look correct for this phone?
I downloaded the drivers here because the phone wouldn't pick up on Keis or smartswitch to do it.
http://www.samsung.com/us/support/owners/product/galaxy-note5-sprint

Bingo308 said:
I think it's been in download mode it says downloading and do not turn off target. Do you think maybe I have a bad version of Odin or installed the wrong drivers. Do these drivers look correct for this phone?
I downloaded the drivers here because the phone wouldn't pick up on Keis or smartswitch to do it.
http://www.samsung.com/us/support/owners/product/galaxy-note5-sprint
Click to expand...
Click to collapse
Yes version ver. 1.5.45.00 looks fine.
Uninstall kies & smartswitch if they are installed and also the Samsung driver suite. Reboot and just install the drivers alone. They may be conflicting.

Don't forget to change usb port from pc that you are using now with another one and see if any changes

tdunham said:
Yes version ver. 1.5.45.00 looks fine.
Uninstall kies & smartswitch if they are installed and also the Samsung driver suite. Reboot and just install the drivers alone. They may be conflicting.
Click to expand...
Click to collapse
I went to the control panel and uninstalled kies and switch but the samsung drivers wont uninstall when i try. it says they uninstalled but they are still there. I tried restarting the computer and trying a few more times but it just wont uninstall.

tdunham said:
Yes version ver. 1.5.45.00 looks fine.
Uninstall kies & smartswitch if they are installed and also the Samsung driver suite. Reboot and just install the drivers alone. They may be conflicting.
Click to expand...
Click to collapse
Ok I finally got it guys. I tried it ob my other computer and everything worked like a charm! The note is working great and lets me into it. Thank you so much for all you're help. I couldn't of done it alone. I just have one more question now. My dad is on AT&T is there a way I can unlock the phone to use the Sprint Note 5 on AT&T for my dad? I have the old sim card that my cousin left in it. It is a AT&T card for some reason not sure why. I thought about calling Sprint and asking them to do it but I don't have an account with them. Any more suggestions on what should do now to get the phone to work for my Dad on AT&T?:fingers-crossed:
Here is the script of the phone from Odin on my laptop.
<ID:0/004> Added!!
<ID:0/004> Removed!!
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N920PVPU2BPD2_N920PSPT2BPD2_N920PVPU2BPD2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1005)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sboot.bin
<ID:0/004> NAND Write Start!!
<ID:0/004> cm.bin
<ID:0/004> boot.img
<ID:0/004> recovery.img
<ID:0/004> system.img
<ID:0/004> cache.img
<ID:0/004> modem.bin
<ID:0/004> RQT_CLOSE !!
<ID:0/004> RES OK !!
<ID:0/004> Removed!!
<ID:0/004> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/005> Added!!
<ID:0/005> Removed!!
<ID:0/005> Added!!

tdunham said:
Yes version ver. 1.5.45.00 looks fine.
Uninstall kies & smartswitch if they are installed and also the Samsung driver suite. Reboot and just install the drivers alone. They may be conflicting.
Click to expand...
Click to collapse
Dang I just tried to open the phone and it still has a Finger Print Lock. How can I get rid of this and gain access to the phone?

Bingo308 said:
Dang I just tried to open the phone and it still has a Finger Print Lock. How can I get rid of this and gain access to the phone?
Click to expand...
Click to collapse
There's a tool for that but it is difficult to use.
You should verify the phone has a clean esn, you can google that.
You wont be able to activate the phone on any U.S. carrier if the meid has been blacklisted anyway.

tdunham said:
There's a tool for that but it is difficult to use.
You should verify the phone has a clean esn, you can google that.
You wont be able to activate the phone on any U.S. carrier if the meid has been blacklisted anyway.
Click to expand...
Click to collapse
I got into the phone last night the FRP was already off. I guess when my cousin had it a year ago it had been turned off. So I hard reset the phone and it worked. Right now all you can do is use it on wifi. I'm gonna get the ESN checked and make sure it is clean then hopefully I can take it to Sprint and they will unlock it so I can use it at attached.

Odin Failing to flash stock firmware

Hey all,
Tried flashing back to stock firmware using my Galaxy S4 GT-I9505 using Odin but im getting this error relating to a pit file. I have googled it and downloaded a few pit files for the specific phone but its still not working.
I have flashed previous devices with this flash tool before with no issues usually just have to click AP and browse to the selected firmware click start and shes golden and it works no dramas. However with this device im having soo much bad luck. I have tried to pull my pit file using Miracle box however that doesnt work either, Ive also tried to pull it using ADB but I need ROOT and I dont have it on this device either. I have also tried to root with odin too and I get the same error. is there another program that I can use to pull my own pit file?
I have copied the Odin Log for a reference so hopefully someone can shed some light on this annoying issue cheers.
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7105TDVUEMK2_N7105TXSAEMK3_N7105TDVUEMK3_HOME.tar .md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003>
<ID:0/003> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)