Recover from soft brick - Samsung Galaxy Ace Plus S7500

Hello everybudy here is a guide to recover from soft brick(I ave only tested it on S7500 not other)
So do it at ur own risk
First download odin3 v1.85
Download stock firmware for ur cont
Extract both in a particular folder
Open odin
Go to Download mode in ur phone and press volume up
Connect ur phone to pc
If odin shows a yellow mark then u are ready to proceed
Mark PDA & and selct file
Click start in odin
Keep patience
After process is over odin will show pass
Now ur phone will reboot
(DO NOT REMOVE USB CABLE TILL ITS REBOOTED PROPELY)
Complete the setup
Now again switch off mobile as as the process has not been completed yet
Go to recovery mode (this time it would be stock recovery not cwm)
In recovery mode select wipe data factory reset and wipe cache partition
Reboot.
Now u are done!!
HIT THANKS IF I HELPED
Odin-http:// www.androidlegend.com/dl/Odin3_v1.85.zip
Stock firmware(pda)- http://www.tsar3000.com/Joomla/inde...ace-plus-firmwares&catid=55:samsung&Itemid=82
Sent from my GT-S7500

whats new in this there is a sticky in which hole process is shown correctly
and 1 thing -
you should edit PDA ...it is different for different countries
you provided the firmware which is not for Indian users
http://www.sammobile.com/firmwares/
this is were you can get firmware for your own country !!

Ok i have edited pda and u can check the link
Also, I am a Indian and have tried this and its almost same
Only we have to change the language
Thanks any way
Sent from my GT-S7500

I had searched but it was not in q n ans. So i put it in this section. I dont know about stickies as i am new to this
Sent from my GT-S7500

There has also a type of soft brick where you will not be able to access download mode. Then odin will not work
then use USB jig. See http://www.xda-developers.com/android/need-a-samsung-usb-jig-build-your-own/

Ya i know
Sent from my GT-S7500

[email protected] said:
Ya i know
Sent from my GT-S7500
Click to expand...
Click to collapse
I know that you know. It was not mentioned so I mentioned it.

Itz showing fail please help asap!!!!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> S7500DDMF2_S7500ODDMF1_S7500DDME1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> system.img.ext4
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
i tried its coming failed,i tried downloading odin and firmware again from sam mobile, evn removed kies still the same please help asap!!

Ashmit Poojari said:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> S7500DDMF2_S7500ODDMF1_S7500DDME1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> system.img.ext4
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
i tried its coming failed,i tried downloading odin and firmware again from sam mobile, evn removed kies still the same please help asap!!
Click to expand...
Click to collapse
Keep Odin open and change USB ports, remount the PDA & flash. Hope this helped, worked for me

Related

[Q&A] [ODIN][UCLB3] UCLB3 Unbrick - Return to stock - Working PIT included

Q&A for [ODIN][UCLB3] UCLB3 Unbrick - Return to stock - Working PIT included
Some developers prefer that questions remain separate from their main development thread to help keep things organized. Placing your question within this thread will increase its chances of being answered by a member of the community or by the developer.
Before posting, please use the forum search and read through the discussion thread for [ODIN][UCLB3] UCLB3 Unbrick - Return to stock - Working PIT included. If you can't find an answer, post it here, being sure to give as much information as possible (firmware version, steps to reproduce, logcat if available) so that you can get help.
Thanks for understanding and for helping to keep XDA neat and tidy!
Attempted to follow the guide here on my old Infuse to breathe some life back into it, but I can't get it to work. Installed the drivers through Kies, Odin detects my phone in yellow. I follow the guide to the letter, but after flashing 'reset' in blue and getting the green 'pass' my phone simply doesn't reboot, nor can I boot it manually. I've removed the battery a few times and it doesn't change the situation. I can still boot into download mode with no issue and have tried flashing a few times, but I'm having no success booting the phone after Odin is done, nor can I get into recovery mode.
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> PHONE_UCLB3.tar.md5 is valid.
<OSM> PHONE_UCLB3.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> modem.bin
<ID:0/003> modem.bin
<ID:0/003> Removed!!
<ID:0/003> Completed..
<OSM> All threads completed. (succeed 1 / failed 0)
Any ideas?
SG2Tiger said:
Attempted to follow the guide here on my old Infuse to breathe some life back into it, but I can't get it to work. Installed the drivers through Kies, Odin detects my phone in yellow. I follow the guide to the letter, but after flashing 'reset' in blue and getting the green 'pass' my phone simply doesn't reboot, nor can I boot it manually. I've removed the battery a few times and it doesn't change the situation. I can still boot into download mode with no issue and have tried flashing a few times, but I'm having no success booting the phone after Odin is done, nor can I get into recovery mode.
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> PHONE_UCLB3.tar.md5 is valid.
<OSM> PHONE_UCLB3.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> modem.bin
<ID:0/003> modem.bin
<ID:0/003> Removed!!
<ID:0/003> Completed..
<OSM> All threads completed. (succeed 1 / failed 0)
Any ideas?
Click to expand...
Click to collapse
I never tried this flash before, but I do have a couple questions before proceeding...
Is your phone AT&T or Rogers?
Are you able to get back into download mode (that is, by method of device fully turned off, holding down both Volume Buttons and inserting the USB cable)?
joel.maxuel said:
I never tried this flash before, but I do have a couple questions before proceeding...
Is your phone AT&T or Rogers?
Are you able to get back into download mode (that is, by method of device fully turned off, holding down both Volume Buttons and inserting the USB cable)?
Click to expand...
Click to collapse
AT&T, the model is I997. I can still get into download mode, but I can't boot normally, nor into recovery mode (by holding volume up + volume down + power button; Samsung logo never appears). I used the included version of Odin with both the UCLB3_Unbrick_1.1.zip and UCLB3_Unbrick_root_1.1.zip files on the linked thread (I tried both).
SG2Tiger said:
AT&T, the model is I997. I can still get into download mode, but I can't boot normally, nor into recovery mode (by holding volume up + volume down + power button; Samsung logo never appears). I used the included version of Odin with both the UCLB3_Unbrick_1.1.zip and UCLB3_Unbrick_root_1.1.zip files on the linked thread (I tried both).
Click to expand...
Click to collapse
I always recommend this one for AT&T (could never try it myself, as I was a Rogers user), but you may have more luck with this (option A or D).
http://forum.xda-developers.com/showthread.php?t=1613523
joel.maxuel said:
I always recommend this one for AT&T (could never try it myself, as I was a Rogers user), but you may have more luck with this (option A or D).
http://forum.xda-developers.com/showthread.php?t=1613523
Click to expand...
Click to collapse
Tried this a few times and it keeps failing. It'll get about 1/3 of the way there and then my computer will make the 'device disconnected' noise and Odin will fail. I left it in download mode, plugged in, without attempting the download to see if it was an issue with my cable or port, and it didn't disconnect...it seems to only be happening when I attempt to flash the md5.
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I997UCLB3-CWM-root-deodex-extras.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> cache.rfs
<ID:0/003> factoryfs.rfs
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
SG2Tiger said:
Tried this a few times and it keeps failing. It'll get about 1/3 of the way there and then my computer will make the 'device disconnected' noise and Odin will fail. I left it in download mode, plugged in, without attempting the download to see if it was an issue with my cable or port, and it didn't disconnect...it seems to only be happening when I attempt to flash the md5.
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I997UCLB3-CWM-root-deodex-extras.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> cache.rfs
<ID:0/003> factoryfs.rfs
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
Click to expand...
Click to collapse
Even with option D? I see C was used, based on the log...
Sent from my Asus MeMO Pad 8"
joel.maxuel said:
Even with option D? I see C was used, based on the log...
Sent from my Asus MeMO Pad 8"
Click to expand...
Click to collapse
For some reason option D is taking an unreasonable amount of time to download (it's been over an hour now), so I had initially skipped it and tried options A and C, with the same results. I'll report back once I am actually able to get option D downloaded.
Same problem with every option. Progress reaches about halfway, then fails.
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I997UCLB3-CWM-root-deodex.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> cache.rfs
<ID:0/003> factoryfs.rfs
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
SG2Tiger said:
Same problem with every option. Progress reaches about halfway, then fails.
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I997UCLB3-CWM-root-deodex.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> cache.rfs
<ID:0/003> factoryfs.rfs
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
Click to expand...
Click to collapse
Last thing I can think of, you are using the Odin that comes with the package right?
joel.maxuel said:
Last thing I can think of, you are using the Odin that comes with the package right?
Click to expand...
Click to collapse
Yes, it should be Odin3 v1.7.
The dev-host file mirrors are down? Does anybody have copies of them to upload?
I need the one with root.
Umaroth said:
The dev-host file mirrors are down? Does anybody have copies of them to upload?
I need the one with root.
Click to expand...
Click to collapse
Sorry, no option A here, but I do have option C (with CWM, deodex, etc) on mirror. See the following link:
http://forum.xda-developers.com/showpost.php?p=58392432
Hope this helps.
Link Are Broken
Umm the link cant be downloaded.. i m trying to restore my infuse but most of the downloadable file is broken or file not found
ZExNos said:
Umm the link cant be downloaded.. i m trying to restore my infuse but most of the downloadable file is broken or file not found
Click to expand...
Click to collapse
Good evening,
Try my mirror:
http://forum.xda-developers.com/showpost.php?p=58392432
Options are limited, only "Option C" but it should be enough to get the job done.
Cheers.

ODIN fail: NAND write fail

I factory reset my Samsung Grand 2 then charged it. When I saw my phone it was updated in kitkat. I accidentally hit the install and reboot. But after that, it stuck in logo screen. I've tried to wipe data, cache and everything. So, I flash it with odin with correct latest firmware. But it keeps on failing and appears firmware upgrade encountered an issue. Please select recovery mode in Kies & try again. Ive tried to fix it with Kies but there's no chance. I also brought it to service center but they said it keeps on failing and the program cant enter.
This is the ODIN log:
ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> root66_VZW_stock_system.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> system.img
<ID:0/003> NAND Write Start!!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I've been searching how to fix my phone.
PLEASE SOMEONE HELP ME.
xilaaa said:
I factory reset my Samsung Grand 2 then charged it. When I saw my phone it was updated in kitkat. I accidentally hit the install and reboot. But after that, it stuck in logo screen. I've tried to wipe data, cache and everything. So, I flash it with odin with correct latest firmware. But it keeps on failing and appears firmware upgrade encountered an issue. Please select recovery mode in Kies & try again. Ive tried to fix it with Kies but there's no chance. I also brought it to service center but they said it keeps on failing and the program cant enter.
This is the ODIN log:
ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> root66_VZW_stock_system.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> system.img
<ID:0/003> NAND Write Start!!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I've been searching how to fix my phone.
PLEASE SOMEONE HELP ME.
Click to expand...
Click to collapse
See if you have the proper firmware and read the instructions here: http://forum.xda-developers.com/galaxy-grand-2/general/stock-firmware-grand-2-google-drive-t2849501
Or else you could ask help from anyone having a similar phone in this forum: http://forum.xda-developers.com/galaxy-grand-2
I tried the instruction but it didn't work still failed. I also tried to flash it with original stock but it says SW REV CHECK FAIL : [sbl1]Fused 1 > Binary 0
Im losing hope. Please help :crying: :crying:
xilaaa said:
I tried the instruction but it didn't work still failed. I also tried to flash it with original stock but it says SW REV CHECK FAIL : [sbl1]Fused 1 > Binary 0
Im losing hope. Please help :crying: :crying:
Click to expand...
Click to collapse
I don't know specifically about your phone.
Only asking someone here would help: http://forum.xda-developers.com/galaxy-grand-2/help
I tried to downgrade my phone but it shows SW REV CHECK FAIL : [aboot]Fused 2 > Binary 1

Can not flash official firmware

Hello,
I want to flash to G920FXXU1AOD4 from G920FXXU1AOE3.
I tried to use Odin 1.85 and 3.04.
This is the error that I'm getting in Odin 1.85:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G920FXXU1AOD4_G920FOJK1AOD4_G920FXXU1AOCZ_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
Why can't I flash to this firmware?
Help...
r'n'b said:
Hello,
I want to flash to G920FXXU1AOD4 from G920FXXU1AOE3.
I tried to use Odin 1.85 and 3.04.
This is the error that I'm getting in Odin 1.85:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G920FXXU1AOD4_G920FOJK1AOD4_G920FXXU1AOCZ_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
Why can't I flash to this firmware?
Help...
Click to expand...
Click to collapse
Did you turn on USB DEBUGGING?
Hello again
I had the same problem with flashing rom with odin... I found a solution and explained it how to fix mine...
I hope it be helpful
http://forum.xda-developers.com/galaxy-s6/help/help-odin-stuck-start-write-nand-t3127992
k2evil said:
Hello again
I had the same problem with flashing rom with odin... I found a solution and explained it how to fix mine...
I hope it be helpful
http://forum.xda-developers.com/galaxy-s6/help/help-odin-stuck-start-write-nand-t3127992
Click to expand...
Click to collapse
Ok... I Solved my problem finally... I spent almost 3 days in forums to find a solution... So i give you guys a summary what I do:
1) Find my phone's pit file according to model and storage capacity (Mine is G920F 32GB)
2)Then the trick is use ODIN V3.10.6 insist of V3.09... http://forum.xda-developers.com/showthread.php?t=2711451
3)If you face with hidden.img problem, extract the rom's file and rename the file hidden.img to hidden.img.tar and flash it by ODIN (Put this file on AP)...
Wait for some minutes and there is where magic happens
Click to expand...
Click to collapse
I don't understand your solution.
What do I need to do with the pit file?
My device is also G920F 32GB.
The USB DEBUGGING is on.
r'n'b said:
I don't understand your solution.
What do I need to do with the pit file?
My device is also G920F 32GB.
The USB DEBUGGING is on.
Click to expand...
Click to collapse
I heard from someone that Stucking in Start Write NAND is because of pit file...
but forget about it.. try without pit file. download the lastest odin v 3.10
usually process fails when it try to flash hidden.img... if it happen for you, do the 3th step
k2evil said:
I heard from someone that Stucking in Start Write NAND is because of pit file...
but forget about it.. try without pit file. download the lastest odin v 3.10
usually process fails when it try to flash hidden.img... if it happen for you, do the 3th step
Click to expand...
Click to collapse
Finally I managed to flush the ROM
Odin3_v3.10.6 did the job.
Thanks!
Your welcome buddy... just don't forget to hit the thank button

Odin Failing to flash stock firmware

Hey all,
Tried flashing back to stock firmware using my Galaxy S4 GT-I9505 using Odin but im getting this error relating to a pit file. I have googled it and downloaded a few pit files for the specific phone but its still not working.
I have flashed previous devices with this flash tool before with no issues usually just have to click AP and browse to the selected firmware click start and shes golden and it works no dramas. However with this device im having soo much bad luck. I have tried to pull my pit file using Miracle box however that doesnt work either, Ive also tried to pull it using ADB but I need ROOT and I dont have it on this device either. I have also tried to root with odin too and I get the same error. is there another program that I can use to pull my own pit file?
I have copied the Odin Log for a reference so hopefully someone can shed some light on this annoying issue cheers.
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7105TDVUEMK2_N7105TXSAEMK3_N7105TDVUEMK3_HOME.tar .md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003>
<ID:0/003> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)

samsung galaxy note 10.1 shows encryption failed, already tried to install new firmware through odin doesnt work

my tablet shows encryption failed message, reset phone but nothing happend when i click on reset button, moreover i tried going to the wipe data/factory reset option but my tablet wont allow me to go that menu, it simply restarts the device.
anyways i read that i should try and install a new firmware for my device but i did try using many odin versions and different firmwares, this is what odin shows me:-
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N8000XXUDNE5_N8000OLBDNE3_N8000DXUDND1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> boot.img
<ID:0/003> NAND Write Start!!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<ID:0/003> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
did u flash the latest firmware ? n make sure the right odin to flash it
howdeedodat said:
did u flash the latest firmware ? n make sure the right odin to flash it
Click to expand...
Click to collapse
Yes I did use the latest firmware, and also tried using old ones
Also, which version of odin should I use exactly?
adityaka said:
Yes I did use the latest firmware, and also tried using old ones
Also, which version of odin should I use exactly?
Click to expand...
Click to collapse
depend which android that u trying to flash

Categories

Resources