Related
Hello everyone,
First let me say what a great forums this is, thanks to those who created it and the people here keeping it active.
I been having a problem connecting to my wi-fi at work. Several people who have mac laptops and iphones are able to find the wi-fi and connect right away in my office.
On my ATT Tilt it doesnt locate it. I enter the network id and when the device finds the signal it asks for a network key
Would anyone know why it isn't getting a network key or where can I find the network key to the wi-fi device?
Your help would be greatly appreciated.
Thanks,
-impact2oo
The network detected is a security enabled network and you have to ask the network administrator for the key
So, I'm already getting tired of plugging into the USB every time I want to transfer file. Is there anyway to transfer file without using the hard wire? WLAN or bluetooth or any suggestion are welcome! Please show me how to do it though! (Because I tried and searched but can't figure it out!)
Thanks
The phone supports bluetooth FTP, which allows just what you're looking for, I would type up a description but im sitting on the floor typing on my phone.. so maybe someone else can But in a nutshell, pair the 2 devices, (both must support bluetooth ftp), set up a bluetooth ftp share on the phone thru the bluetooth settings app, connect to the phone over bt.
its notably slower than the usb2.0 transfer though.
bluetooth
beam file thru bluetooth from a laptop or pc. set your phone to discoverable under bluetooth settings and on your bluetooth enabled pc you should be able to right click a file and click on sent to... and bluetooth device should be an option. a new screen will show up where you can search for nearby bluetooth devices and the rest should be self explanatory, the default password should be 0000 unless you changed it. hope this helps. bluetooth is rather slow tho. i usually only use this method for small cab files. i use the usb cable or a sd card reader for bigger files.
Great! I finally figured it out. So I have to enable FTP on this phone. lol
Total Commander has a LAN plugin that'll allow you to access samba shares on other computers. should be much faster than transfers via bluetooth as it's done over wifi.
You can also use Activesync.
vexingv said:
Total Commander has a LAN plugin that'll allow you to access samba shares on other computers. should be much faster than transfers via bluetooth as it's done over wifi.
Click to expand...
Click to collapse
I can access shares on my computer without samba or Total Commander. I just use file explorer.
This is really easy-peasy.
All you have to do is connect your phone to your Wi-Fi network, and then go into the File Explorer.
Click Menu > Go To > Open Path > New Path...
In the dialog box, type in the path to the share on your PC (yes you need to share the location on your PC that you want your phone to be able to access), for instance;
\\mypc\sharename
Click OK
Now you will be able to browse the folders on your PC and transfer files to/from it to your heart's content, just like you were looking on your own phone's filesystem.
Happy file transferring! :O)
ur awesome!!!!
Need help
Jim,
I must be a bit thick. I have my network set up for file sharing, but when I followed your instructions, I get a Network Log On screen and I'm not sure what I need to enter. User name... Password.... Domain.... ????? I'm already logged on securely to my WiFi network, so I do not understand what I should be entering here.
Can someone help me out here?
Thanks very much.
Skydog said:
I have my network set up for file sharing, but when I followed your instructions, I get a Network Log On screen and I'm not sure what I need to enter. User name... Password.... Domain.... ????? I'm already logged on securely to my WiFi network, so I do not understand what I should be entering here.
Click to expand...
Click to collapse
Sounds like you need to enter your WINDOWS username/password to log in to your windows pc.
You may also need to create some shared folders on the windows pc if you have not already.
As mentioned, my network is already set up for sharing (among several systems) including specific drives and folders.
I already tried using my Windows username and password, without success, which is why I posted my question.
I'm still clueless.
I'd love to get this to work, but I'm not getting anywhere either.
I do have network shares set up.
I'm connected on wifi.
I go to file explorer->Menu->Open Path->New Path and put in \\Laptopt2310\test which is the computer I want to connect to and a shared folder on that computer.
I get a popup pointing to my wifi indicator saying cannot connect with current connection settings. To change your connection settings, tap Settings.
If I tap settings, it takes me to a connection set up where it says Verizon Wireless with some options under and My Work Network with some options under that.
The advanced tab has a box for select networks and I have Verizon Wireless in the Internet box and My Work Network in the private network box.
I don't want to touch anything there and screw things up.
It's almost like it's trying to do it over the phone's data connection and not wifi, but I did a quick speed test and at least the internet browser is definitely using the wifi connection.
Well, I figured out that I could also do this in resco and total commander.
Both of them connect fine on wifi. Not sure why file explorer doesn't, but I guess it doesn't really matter now.
What's the secret?
I also use Resco. Can you explain exactly what you did to make a successful connection?
Those of you still trying to use File Explorer, the username, password and domain should be your Windows username, Windows password and the name of your PC respectively.
If you don't get any joy using the PC name as the domain, or in the path dialogue, you can use the ip address instead - it may be that your network is having problems resolving names to ip addresses.
Trust me, it really does work, I've never had a problem using it at home on a perfectly bog-standard wi-fi network, with the shares on a Vista PC (it also worked with Windows 2000 before that).
Obviously, you have to be sure you're using your Wifi network and not GPRS / HSDPA.
Hope that helps!
Jim,
After some tinkering, I was successful in getting the Fuze on my network. What a great tip! Many, many thanks for sharing this with us.
No problem, happy to help.
I'm sure this is all in the manual somewhere ;O)
I can pair my phone with the computer through bluetooh, but in the bluetooth settings menu when i select my computer I only see 'Wireless Stereo' and 'Headset' as service. Is this because the laptop might not support bluetooth ftp? Its a new Lenovo T400 with built in bluetooth, I figure that should support it?
Any help is appreciated. Thanks
Don't bother with bluetooth, it's too much hassle, just use the File Manager over Wifi, it's far easier!
But what if I really do want to use bluetooth...?
When I view my bluetooth devices on the laptop I can click properties on my Touch Pro and see the following services: A2DP, Active Sync Bluetooth service, Dial-up networking, Headset audio gateway, Object Push (Obex)
On the phone I go Start->Settings->Connections->Bluetooth and then select my laptop that i'm tethered to and I only see Wireless Steroe, ActiveSync, and headset.
Am I missing drivers on one of the devices? It looks like its possible something wrong on the TP seeing how my vista laptop is listing obex as an option...
Any help is appreciated
first off - i tried searching but could not find any solid info, from start to finish, how to make tethering work
i've never had to tether till now.. tried enabling Internet Sharing and connecting it both via USB and Bluetooth - no success.. i'm using Media Net $15 a month data plan, if that makes a difference (wap Vs gprs in user name but i did try both)...
is anyone using their phone as a modem? what settings do you have? please point the noob in the direction of a step-by-step guide if one is available (i did try to search but nothing than enabling Network connection via registry edit - not relevant)..
thanks a bunch to anyone who could help!
I'm online using the "internet sharing" connection now (in Florida cleaning up after a flood) (Yes, I need to get back to work . . . .).
I also have a Fuze and am using EnergyROM 2.0. Haven't changed any settings since installing the new ROM. Works like a charm for me.
Make sure the proxy box under the MediaNet settings is NOT checked.
vovan75 said:
first off - i tried searching but could not find any solid info, from start to finish, how to make tethering work
i've never had to tether till now.. tried enabling Internet Sharing and connecting it both via USB and Bluetooth - no success.. i'm using Media Net $15 a month data plan, if that makes a difference (wap Vs gprs in user name but i did try both)...
is anyone using their phone as a modem? what settings do you have? please point the noob in the direction of a step-by-step guide if one is available (i did try to search but nothing than enabling Network connection via registry edit - not relevant)..
thanks a bunch to anyone who could help!
Click to expand...
Click to collapse
Open up taskmanager and make sure that activesync is not running on the phone. this will not allow internet sharing to work. what does the phone say when you open internet sharing and click connect?
download a registry editor (i use total commander, and it works just fine).
open it up, go to \plugins\registry\HKLM\Comm\InternetSharing\Settings\ForceCellConnection and simply delete the contents of the value so that it's empty. Go ahead and do a soft reset and open up the internet sharing app. From there, select the Media Net connection and hit connect. Voila, good to go!
Enjoy!
ps I've gotten 2+ Mbps speeds via tethering
Dane Austin said:
Open up taskmanager and make sure that activesync is not running on the phone. this will not allow internet sharing to work. what does the phone say when you open internet sharing and click connect?
Click to expand...
Click to collapse
I keep activesync enabled so that i'm able to receive corporate email when on the road.
I was able to tether via USB (was doing nothing different from last night when i was unable to internet share via USB, however I noticed when shutting down that BT stack crashed); internet sharing app came up automatically once I selected internet sharing right after hooking up the cable to my laptop, and MediaNet was there by default (I guess it's all cooked into the ROM; did not have to delete any registry keys; kudos to NRGZ)... was able to get close to 1Mb/s download speed (upload is really slow however, less than 50Kb/s) - not too bad overall
Still have problem connecting via Bluetooth
maybe i'm having problem pairing laptop and Fuze? is there a pre-defined code/pass key that i'm supposed to use for the Fuze?
i was just using my security/lock code.. when laptop starts dialing (is dial up number *99# correct?), i get the following error box:
------------------------------------------------
Error Connecting to BluetoothConnection
Dialing *99#...
Error 678: The remote computer did not respond. For further assistance, click More Info or search Help and Support Center for this error number.
-------------------------------------------------
Anybody had this issue? or can share their connection settings for Bluetooth?
thanks everyone who responded!
vovan75 said:
I keep activesync enabled so that i'm able to receive corporate email when on the road.
I was able to tether via USB (was doing nothing different from last night when i was unable to internet share via USB, however I noticed when shutting down that BT stack crashed); internet sharing app came up automatically once I selected internet sharing right after hooking up the cable to my laptop, and MediaNet was there by default (I guess it's all cooked into the ROM; did not have to delete any registry keys; kudos to NRGZ)... was able to get close to 1Mb/s download speed (upload is really slow however, less than 50Kb/s) - not too bad overall
Still have problem connecting via Bluetooth
maybe i'm having problem pairing laptop and Fuze? is there a pre-defined code/pass key that i'm supposed to use for the Fuze?
i was just using my security/lock code.. when laptop starts dialing (is dial up number *99# correct?), i get the following error box:
------------------------------------------------
Error Connecting to BluetoothConnection
Dialing *99#...
Error 678: The remote computer did not respond. For further assistance, click More Info or search Help and Support Center for this error number.
-------------------------------------------------
Anybody had this issue? or can share their connection settings for Bluetooth?
thanks everyone who responded!
Click to expand...
Click to collapse
now, i just tried leaving User Name and Password fields blank on the Bluetooth connection wizard, and using dial-up number *99***1#, like they suggest here: Answer Center - Create a Windows XP Dial-Up Networking Connection for a Bluetooth Device , and got a new error:
------------------------------------------------
Error Connecting to BluetoothConnection
Dialing *99***1#...
Error 777: The connection attempt failed because the modem (or other connecting device) on the remote computer is out of order.
-------------------------------------------------
this is just getting funnier but kind of frustrating...
nhshah7 said:
download a registry editor (i use total commander, and it works just fine).
open it up, go to \plugins\registry\HKLM\Comm\InternetSharing\Settings\ForceCellConnection and simply delete the contents of the value so that it's empty. Go ahead and do a soft reset and open up the internet sharing app. From there, select the Media Net connection and hit connect. Voila, good to go!
Enjoy!
ps I've gotten 2+ Mbps speeds via tethering
Click to expand...
Click to collapse
tis fixed my tethering issue... thank you!
Damn AT&T trying to force people to pay more for tethering... shame!
smittyofdhs said:
tis fixed my tethering issue... thank you!
Damn AT&T trying to force people to pay more for tethering... shame!
Click to expand...
Click to collapse
smitty, do you tether via bluetooth or usb? i have no problem with usb now but still get the same "error 678: the remote computer did not respond..." i wonder if my BT driver is corrupt or i'm blacklisted by at&t
if anyone is able to connect using bluetooth and Internet Sharing app on Energy or any other similar ROM, can you share your dial-up settings with me?
after i start Internet Sharing app, with PC Connection = Bluetooth PAN and Network Connection = MEdia Net, and then right click my Bluetooth Modem in Dial-up Network Places on my laptop, the icon shows "connecting" for about 5 seconds (and the data icon H on the phone starts rotating) and then the error comes up on computer screen.. i can't believe no one else has had the same issue, i must be something with my laptop
vovan75 said:
smitty, do you tether via bluetooth or usb? i have no problem with usb now but still get the same "error 678: the remote computer did not respond..." i wonder if my BT driver is corrupt or i'm blacklisted by at&t
if anyone is able to connect using bluetooth and Internet Sharing app on Energy or any other similar ROM, can you share your dial-up settings with me?
after i start Internet Sharing app, with PC Connection = Bluetooth PAN and Network Connection = MEdia Net, and then right click my Bluetooth Modem in Dial-up Network Places on my laptop, the icon shows "connecting" for about 5 seconds (and the data icon H on the phone starts rotating) and then the error comes up on computer screen.. i can't believe no one else has had the same issue, i must be something with my laptop
Click to expand...
Click to collapse
I haven't been able to get my HP laptop to pair via bluetooth with my Fuze yet so I was doing USB. With regards to your issue, do you ahve one or two pull down menus in INternet Sharing app? If you have 1, then your registry needs to be hacked. AT&T used a registry key to force Internet Sharing app to only use the isp.cingluar access point (instead of wap.cingluar). If you pay the extra bucks for the full unlimited with tehtering then your account is setup to use isp.cingluar as well as wap.cingluar. If you just have the normal unlimited w/o tehtering option (which is not unlimited it caps at 5GB/month) then you only can use wap.cingluar. THis is how AT&T is going more easily find people using the cheaper plan with thethering and of course charge them up the butt for violation of the TOS (that they keep changing). Removing the registry key, fixes the issue.
smittyofdhs said:
I haven't been able to get my HP laptop to pair via bluetooth with my Fuze yet so I was doing USB. With regards to your issue, do you ahve one or two pull down menus in INternet Sharing app? If you have 1, then your registry needs to be hacked. AT&T used a registry key to force Internet Sharing app to only use the isp.cingluar access point (instead of wap.cingluar). If you pay the extra bucks for the full unlimited with tehtering then your account is setup to use isp.cingluar as well as wap.cingluar. If you just have the normal unlimited w/o tehtering option (which is not unlimited it caps at 5GB/month) then you only can use wap.cingluar. THis is how AT&T is going more easily find people using the cheaper plan with thethering and of course charge them up the butt for violation of the TOS (that they keep changing). Removing the registry key, fixes the issue.
Click to expand...
Click to collapse
sounds like we are in the same boat here - i can tether my HP laptop with Fuze via USB no problem now using Internet Sharing app, but no luck with Bluetooth whatsoever... i don't think there is an issue with the registry ever since i switched to Energy 2.0 ROM which must have the settings customized (so yes, I do have 2 pull down menus, and I have Media Net selected in the second one). So, I tried to use both wap.cingular and isp.cingular APN's (both [email protected] and [email protected] for User Name, CINGULAR1 for password; then I tried leaving User Name and Password fields blank...) with no success... nothing works, damn it!!!
looks like it gets paired up briefly, then starts dialing and gets the error in a couple of seconds.. the problem must be with the bluetooth dial-up settings for AT&T, because: 1) i have no problem tethering via USB; 2) Fuze is being paired up with my laptop and trying to use HSPDA data connection (as indicated by rotating H on the phone for a few seconds while my laptop tries to dial up).
by the way, have you tried dialing *99# or *99***1# (i tried both numbers as well as *99***3# for Samsung phones) from your Fuze, did you get any modem dial tone??
thanks!
I was able to connect to internet through bluetooth by using the following settings.
After pairing the bluetooth on both Fuze and laptop:
On my Fuze: open 'Internet Sharing' then select Bluetooth PAN and choose the appropriate network connection (in my case TZones) then tap 'Connect'
On the laptop: open bluetooth neighborhood then 'discover service' or 'explore' on the Fuze device. You should see 'Network Access Point on [Fuze]' and then double click on it.
Done.
ICS on AT&T HTC Fuze Cut Off (NRG Rom Series 2.0)
AUTiger83 said:
I'm online using the "internet sharing" connection now (in Florida cleaning up after a flood) (Yes, I need to get back to work . . . .).
I also have a Fuze and am using EnergyROM 2.0. Haven't changed any settings since installing the new ROM. Works like a charm for me.
Make sure the proxy box under the MediaNet settings is NOT checked.
Click to expand...
Click to collapse
I've been using ICS with no problems with a ThinkPad T43 for a few weeks at work to circumvent the proxies and reach out to my home machine via RDP. The RDP app for the Fuze just doesn't cut it with its whopping 640x480 screen. Turns out that AT&T in NY/NJ is somehow monitoring the connections. I was watching a bunch of videos to pass some downtime, and I guess I triggered some kind of alert on their end. ICS will connect to MediaNET with no problems (settings read wap.cingular), ICS status shows connected (I am connecting over USB) and my ThinkPad network connection shows a private IP address handed to it by the phone (192.168.0.x range). However when I am trying to connect to something, I'll get timeout errors. Running a simple ping comes back with no DNS capabilities as I can't even ping google.com... Has this happened to anyone on the forum? Can anyone offer some advice? I am thinking of just calling AT&T and playing dumb, saying that I was watching videos, as well as moving lots of music from my home computer via FTP ... Any advice appreciated. I pay for the $40/month PDA plan... I don't see the point of paying for tethering when you're already paying for data. Yes, before people start flaming me, I was stupid by using the connection to watch a bunch of videos, but you're able to watch youtube on your phone anyway....
--UPDATED 7-31-09 3:03PM --
So I downloaded ICS Control v0.21, which by the way is an awesome program. I went through the config, was able to connect my laptop to my HTC Fuze via WiFi. That was easy. As palringo (win xp version) was connecting in the background, I was able to do a test google search and get back results. Ran a continuous ping on google (ping google.com -t). Turns out that after about 25 ping replies or so, just about the time it took me to do a few web searches, the requests start timing out. Directing the ping at another website shows that the ping request couldn't find the host... basically the same problem I had tethering over USB. It's as if the AT&T network is determining that the request is coming from a PC and not the PDA and not passing the DNS requests... Either way, I tried to ping google via 74.125.45.100 and got back a request timed out. I am now wondering whether or not this may have to do with the packet MTU and whether or not the PDA packets differ from regular PC/WinXP packets. I just don't know enough about networking to be able to know. I am able to ping the Fuze gateway (for all-intensive purposes set to 192.168.2.1) and get back replies within 2-4ms. I really would love to hear from someone to whom this has happened before. I haven't called AT&T yet as the data connection on the phone itself works just fine, and I am able to load pages on the phone just fine. It's just any form of ICS that's beat...
Come on XDA-Dev, I know the collective intelligence can come up with something here.
I didn't think ATT could detect the difference between tethered requests and ones that originate on the phone, that would be bad though, if that were the case. Since the previous poster was watching videos, it seems to me the bandwidth would be the comparable to watching videos with the YouTube app on the Fuze, which I'm sure is within the terms of service contract.
My experience is closer to vovan75's. ICS works fine via USB, but does not work via Bluetooth. The strange thing is with the BT connection, I can ping the gateway, and even do nslookup with the default DNS, and sometimes if I get lucky, the connection works for a few seconds, allowing a page to load, totally random.
I thought everything worked using the original ATT rom, so I have a feeling culprit is something in the NRG rom, or maybe a radio incompatibility. I might re-flash to the old official rom just to try this, before the next time I update to the latest NRG build.
My setup:
Fuze with EnergyROM (July 22 build)
Radio: 1.14.25.35 (from official HTC 6.1 update)
Notebook with Windows 7 RTM
Windows calls this "Bluetooth Network Connection" (I don't see a reference to DUN, at least not in Win7)
ICS using BT (not working):
IPv4: 169.254.46.56
Gateway: 169.254.247.172
ICS using USB (working):
IPv4: 192.168.0.102
Gateway: 192.168.0.1
Windows 7 calls this "Remote NDIS based Internet Sharing Device"
DSLReport speed test (Flash) - down: 696Kbs, up: 336Kbs (varies quite a bit, much better at night of course)
Okay, figured it out. The DHCP setting for the bluetooth PAN should be off (I know, counter-intuitive). I found this by diff'ing the entire HKLM-Comm registry branch of the last EnergyROM build (Sept 6) vs the official ATT 6.1 rom (5.11.502.2WWE), which did work after all.
Code:
Windows Registry Editor Version 5.00
[HKEY_LOCAL_MACHINE\Comm\BTPAN1\Parms\TcpIp]
"EnableDHCP"=dword:00000000
BTW, you don't need to setup Dial-Up Networking when using the Internet Sharing application (IntShrUI.exe). DUN needs to be configured on the PC when using the phone's modem bluetooth service, and AFAIK, needs to be provisioned by AT&T before it will work. The Internet Sharing app acts like an uplink for paired devices in the bluetooth personal area network (PAN).
rasterX, you rock! That little illogical registry fix is all I needed... I'd been banging my head against this Bluetooth DUN thing for days.
Thanks!
I am using ARHD ROM (with Bricked Kernel).
My car can access and read out RSS threads and has a lot of interactive media functions, including being able access the internet via my bluetooth enabled phone. But I can't seem to get it to work fully, and really don't know if it is a ROM / Kernel / Phone issue or a car issue. I just don't know enough about the various bluetooth protocols etc, and as much as I research it, I keep going around in circes.
The car will connect to the phone and work fine as a bluetooth headset for telephone calls. It will also display the caller picture without issue and will access and read out my emails (using stock sense Mail client) and SMS messages. It also seems to connect to audio OK (although I never use it as it has a USB port that will accept a pop drive, so all my music is on the dashboard).
But the internet connection doesn't seem to work. I have looked into this and can't work out if it is a PAN or DUN profile issue. Soemtimes I can get the phone to show an internet connection being available to the car, sometimes it doesn't depending on which ROM I use and I can't seem to get any to work regardless.
Looking on the website, it claims the following:
How can I configure my mobile device for internet or BMW TeleServices usage?
In the operating manual of your mobile device you will find instructions on configuring “Access Point Name (APN)”; other names for this may be “Internet Settings”, “Modem Settings” or “Tethering Settings”. The required settings are available from your service provider. Please note that most Sony Ericsson mobile devices only recognise the first entry in the APN list, so it is recommended that all other APN configurations be deleted.
Can somebody please help me with this. I really am baffled as to how to get this to work.
Sent from my HTC Sensation Z710e using Tapatalk
Bump. Anybody?
Sent from my Motorola DynaTAC using Tapatalk (feels like it at times with this phone)
It has been a year or 2 since I got bluetooth networking going. Today I tried to get my phone to connect to my windows 7 desktop and.... it couldn't even connect sadly enough. Anyways this is from memory so it may or may not be correct. I don't like posting incorrect stuff because you never know who will read/flame.
1. pair your phone to the other device
2. connect via bluetooth your phone to the other device
3. I used the app in the link below to turn on bluetooth tether. Your kernel needs to support this feature. Just a note, there are 2 apps off the link. One is wifi only, the other does bluetooth and wifi. Assuming you get this app, turn on bluetooth tether. I don't know if you should turn tether on then connect bluetooth. Maybe it doesn't matter.
4. This step I don't quite understand. The bluetooth tether should "offer" a network service to the remote device. The remote device in turn must recognize the service and use it. DHCP is the easiest to auto configure everything. If you need a name server, use 8.8.8.8 since that is a public dns server by our google overlords.
http://code.google.com/p/android-wifi-tether/
Hello Guys,
Please does anyone know how to set up androids wireless network domain?
For instance, if I connect to a wireless network which is running on a particular domain, in order to connect to the internet of that wireless connection, i need to specify its domain. Android is not able to pick up the correct domain or if it does, i cant see it and due to that I wish to set it up manually.
I tried using iphone and I was able to edit the domain settings but when I come back to Android which is my favorite, I cant seem to edit the domain. Cant even find where it is, in order to set it. Thus I am able to connect to the wireless network but cannot use its internet on my phone.
By the way, I am using a google nexus 5.
Any help would be appreciated a lot.
Thank you.
Frisbeeous said:
Hello Guys,
Please does anyone know how to set up androids wireless network domain?
For instance, if I connect to a wireless network which is running on a particular domain, in order to connect to the internet of that wireless connection, i need to specify its domain. Android is not able to pick up the correct domain or if it does, i cant see it and due to that I wish to set it up manually.
I tried using iphone and I was able to edit the domain settings but when I come back to Android which is my favorite, I cant seem to edit the domain. Cant even find where it is, in order to set it. Thus I am able to connect to the wireless network but cannot use its internet on my phone.
By the way, I am using a google nexus 5.
Any help would be appreciated a lot.
Thank you.
Click to expand...
Click to collapse
+1
i too want to know , how to do that ??