I have a defy mini LATAM version i tried to flash it with an indian defy mini sbf that was available on xda. The flash ran till rebooting the phone and then phone woudnt turn on not even to the boot loader mode. i tried everything i know to get it working(not even an led is turning on when i coonect it to the comp). i fully charged the battery using an external charger. when i connect the phone to my system it says unknown device i tried to re install the motorola drivers with no effect. any help as of how to flash the correct sbf would be welcome.
Related
Hi, i've a X10mini (E10i) and charging it with a PC by USB it reboot, as it was still connected, it reboot in flash mode. I disconnect it and try to turn it on, but it was bricked. I try 3 times to flash Stock rom with SEUS, won't work.
Does anybody know some other way i could try to fix it?
I just inherited a US Verizon Xoom 4G LTE + WiFi that was apparently bricked a while back. It was running Android 4, but not 4.1 or 4.2. They weren't sure which exact version, just that it was pre 4.1. It was originally a 3G+WiFI and was sent in for the 4G LTE upgrade a while back. When you power it on, it stops at the Red M logo. I have no idea what was attempted before but hope someone here can help me at least get it back to stock. For reference, I am using a Windows 8 PC. I do have the Motorola drivers installed and the Android SDK installed to C:\SDK-Tools.
If I hold Volume Up and Power, it reboots and says "Starting RSD protocol support 3. Onewire: Charger is not connected or battery is not being charged... Battery charge Level: 100% (the charger is plugged in, btw). I have it connected to the pc via the oem usb cable. When I plug the cable in, windows recognizes the device and device manager shows and Motorola USB Device->Motorola Flash Device is connected. I installed RDS Lite v5.6.4 (also tried 5.7. Haven't found anything newer) and ran it as Adminitrator but it does not show anything in device properties when I click Show Device no matter which port I select. If I reboot (Power + Vol up) then immediately press Vol up when the Red M shows, it boots into fastboot mode (Starting Fastboot protocol support is displayed). If I run fastboot devices from the command line, the device and id is listed. So I know that windows can see it. ADB commands also appear to work when I let it boot normally and it sticks at the Red M.
Any idea why RSD Lite would not be able to connect to the device? I have downloaded this firmware - VZW_MZ602_signed_IMM76L_signed_vzw_MDM6600_03.1A.6 5_signed_usr_LTEDC_U_07.1F.00.combo.sbf\VZW_MZ602_ signed_IMM76L_signed_vzw_MDM6600_03.1A.65_signed_u sr_LTEDC_U_07.1F.00.combo.sbf in the hopes of restoring it with RSD Lite, but of course I cannot get it to connect.
My ultimate intention is to get some rom with at least android 4.1, possibly 4.2, installed so I can test some apps we use at work. Thanks in advance for any help.
Ok, so I figured this out. I did not realize RSD Lite would not work with USB 3.0 ports. That was all I had open on my computer so plugged in there. Unhooked another device, plugged into a USB 2.0 port in the device was instantly recognized. I was able to push the image and all booted back up fine, on Android 4.0.4.
Now I am off to find how to put CM 10.1 on here.....unless someone knows a simple way to do that
Hi everyone!!! Last week i tried to upgrade my ICS stock rom with jellybean, but my phone powered down! Now the Pantech doesn't power up. No bootloader, no fastboot. The computer doesn't recognize the device (i have all drivers installed on). but, when i connect for the first time the usb cable, my pc installs the QHSUSB_LOAD drivers, and then, after 2-3 seconds, it gives to me an error (exclamation mark)in the Device Manager for this driver. It displays an error also to the pantech ADB interface. My Phone is dead. I connect usb cable and it gives three quick sounds (no device connected). HELP Me, please!!! Thank you! Alf :crying::crying:
Pantech Discover JB Bricked too
I am in the same boot, had CWM and rooted with JB and all was fine so I decided to try a custom ROM and when it tried to reboot, it never came back on. When I plug into PC get QHSUSB_DLOAD as hardware but not able to show up in ADB of Fastboot. Please help.
I usually keep flashing ROMS.
This time in sheer confidence I didnt charge the battery full.
I was switching from mokee 4.4 to CM11.
I wiped everything for a fresh install and unfortunately CM11 didnt install.
The tab restarted and now it wont go into recovery. what just happened?
It is just showing logo and I cannot get into Odin more either.
The tab had about 30% battery when it shut off and I cannot reach a charger for it for the next 4 hours.
Can I switch it off in any way to save battery?
the phone has switched off now. Is service center the only alternative? the tab was rooted with mokee installed.
devarshi84 said:
the phone has switched off now. Is service center the only alternative? the tab was rooted with mokee installed.
Click to expand...
Click to collapse
Try charging it when you have time and then try re flashing the stock Rom before taking it to service center
will the tab 2 charge without a recovery or ROM in place?
devarshi84 said:
will the tab 2 charge without a recovery or ROM in place?
Click to expand...
Click to collapse
I think it should
Ok, the tab2 is charging. thank you
I installed all the necessary drivers and odin and recovery on my laptop.
The tab2 is giving error on pc (this device wont start) mtp uSB. THe tab is stuck at 'samsung p3100' logo.
If it is any help, I have a working p3100 also running on stock firmware.
what should be my next step? I think I can manage if only I can get odin to recognize my phone or get into recovery (both of which seem to be missing.)
devarshi84 said:
Ok, the tab2 is charging. thank you
I installed all the necessary drivers and odin and recovery on my laptop.
The tab2 is giving error on pc (this device wont start) mtp uSB. THe tab is stuck at 'samsung p3100' logo.
If it is any help, I have a working p3100 also running on stock firmware.
what should be my next step? I think I can manage if only I can get odin to recognize my phone or get into recovery (both of which seem to be missing.)
Click to expand...
Click to collapse
Try reinstalling drivers
@shsagnik : Thank you very much for helping out.
I got installed all drivers by using the other P3100. But when I connect the bricked p3100, pc doesnt install MTP USB drivers. Under device manager it says " failed to start".
ODIN doesn't recognize it. either.
My mistake was I flashed everything on the phone including the internal memory.
PS: Can I force ODIN to recognize my phone?
Ok, my almost bricked device is back and runnning.
This might just help somebody. but my android handset was on a logo only mode. something in the combination of
Attaching it to pc (windows 7 64-bit)
re-installing and rejigging drivers
trying to let ODIN identiify
connecting via Samsung kies (I also tried restore on kies).
connecting a working android phone instead of the dead phone with pc to find and install drivers.
worked.
PS: I also let it sit dead powered off (worked only when charger was attached) for a whole day before trying to boot into recovery or bootlaoder (both worked).
devarshi84 said:
Ok, my almost bricked device is back and runnning.
This might just help somebody. but my android handset was on a logo only mode. something in the combination of
Attaching it to pc (windows 7 64-bit)
re-installing and rejigging drivers
trying to let ODIN identiify
connecting via Samsung kies (I also tried restore on kies).
connecting a working android phone instead of the dead phone with pc to find and install drivers.
worked.
PS: I also let it sit dead powered off (worked only when charger was attached) for a whole day before trying to boot into recovery or bootlaoder (both worked).
Click to expand...
Click to collapse
Awesome, now please change the title to solved
Hey guys,i have Lg g2 800 at&t i installed a custom LP in it,after few hours it,s touch stopped working then flash it with KK firmware but no luck then i apply hardbrick proccess on it after flashing images i flash it KK firmware then it,s touch was working auto like a ghost using it then i thought to write other firmware images on it so i did agian same proccess i was trying it to connect in qualcomm mode with pc but now when i insert cable in pc auto detect the phone in qualcomm mode 9008 i short resistence many time with cable or without cable bt whenever i connect it with pc phone auto connect in qualcomm mode,so i put the phone for 2 weeks beside today when i connect it pc it,s still same it,s same with battery or without battery and not powering on also,sorry for my bad english.it,s make me crazy dont know what to do now.Experts please