Hi everyone!!! Last week i tried to upgrade my ICS stock rom with jellybean, but my phone powered down! Now the Pantech doesn't power up. No bootloader, no fastboot. The computer doesn't recognize the device (i have all drivers installed on). but, when i connect for the first time the usb cable, my pc installs the QHSUSB_LOAD drivers, and then, after 2-3 seconds, it gives to me an error (exclamation mark)in the Device Manager for this driver. It displays an error also to the pantech ADB interface. My Phone is dead. I connect usb cable and it gives three quick sounds (no device connected). HELP Me, please!!! Thank you! Alf :crying::crying:
Pantech Discover JB Bricked too
I am in the same boot, had CWM and rooted with JB and all was fine so I decided to try a custom ROM and when it tried to reboot, it never came back on. When I plug into PC get QHSUSB_DLOAD as hardware but not able to show up in ADB of Fastboot. Please help.
Related
Hi,
I wanted to update an I9003 from Android 2.2 to 2.3.4 JPKP5 (with latona.pit, I used this combination twice with two other phones), I used odin 1.85 for this purpose.
Connected the phone to the PC, it failed to install one of the drivers, but, it appeared in odin... so, I continued :cyclops:.
the operation stopped at about the mid-way and there was "FAIL" and red slot....
Unplugged and plugged it (without restarting, and the progress bar was still there) odin recognized it but couldn't flash again, stuck at "SettingUpConnection"...
I pressed the power button to restart it... then it showed (Phone <!> PC) logo in the screen....
Turned it off by removing the battery, I doesn't boot to recovery nor normal boot...
BUT, I can go into download mode without being apple to connect it to the PC, it shows me (USB device is not recognized) and doesn't appear in odin.
SO.... What is the phone's state and what can I do to fix the problem??
Thank you in advance
you have installed the drivers in your pc? If not yet, install KIES first.
I had the same issue. Even after installing kies my com: port didn't detect . So i reinstalled Windows 7 & installed kies after that. Now odin worked perfect.
Sent from my GT-I9003 using xda app-developers app
I know what you're talking about... the drivers are installed properly and I connect other device to odin properly... I can tell that the problem is because of the device... It's dead for ever!!
I think it is bricked. So try to reinstall the drivers and install any other rom. If it is not working try a JTAG repair.
Helo there
I have a Motorola Fire Xt 530, I had rooted it and it was going on fine back then, until one day I realized that I cannot connect the phone by using the USB, in the computer it keeps on saying USB not recognized, and on the phone it's only charging and no option for usb mass storage. I had installed the Motorola device manager for the driver and had tried on a different computer. I had tried to to flash mode by pressing the power button plus the volume down key and camera button, and the same thing still happened, the computer doesn't recognize it. I had also checked the enable debug.
What can I do to fix it since I want to flash the Ice Cream Jelly rom, since it's not recognized i cannot flash it to the computer.
Thank you for your help in advance
Cheers
benzyboy said:
Helo there
I have a Motorola Fire Xt 530, I had rooted it and it was going on fine back then, until one day I realized that I cannot connect the phone by using the USB, in the computer it keeps on saying USB not recognized, and on the phone it's only charging and no option for usb mass storage. I had installed the Motorola device manager for the driver and had tried on a different computer. I had tried to to flash mode by pressing the power button plus the volume down key and camera button, and the same thing still happened, the computer doesn't recognize it. I had also checked the enable debug.
What can I do to fix it since I want to flash the Ice Cream Jelly rom, since it's not recognized i cannot flash it to the computer.
Thank you for your help in advance
Cheers
Click to expand...
Click to collapse
use a different usb cabe and port on computer
Hi thanks for the reply
I had tried using 3 different cables in different computers also, and they all say the same thing, usb device not recognized. The funny thing is I can use the motorola cable to connect my nexus 7 to the computer, but it cannot connect the motorola fire xt. Is there a possibility that the phone system's is damaged? If so how can it be fixed?
Thanks
MOKHD said:
use a different usb cabe and port on computer
Click to expand...
Click to collapse
Anyone can help me?
Thanks
Hi guys
i think i bricked my su870
as of now, if i connect it to a charger or press the power on button, it will only bootloop
LG logo appears then it restarted back
i tried to revive it by using the wkpark boot, but apparently my windows 8.1 cant even detect my phone as omap (i've removed the battery.also tried to plug the usb cable directly and even tried connect it while holding Vol + )
it just said Unknown USB Device (Device Failed Enumeration) in device manager and windows keep on connect/disconnecting it.tried to right click on it and update the driver.pointed it to the OMAP folder,but it just straight away said latest driver has been installed
try another cable and windows doesnt even detect the phone at all
any idea how do i revive this phone ?
thanks
I usually keep flashing ROMS.
This time in sheer confidence I didnt charge the battery full.
I was switching from mokee 4.4 to CM11.
I wiped everything for a fresh install and unfortunately CM11 didnt install.
The tab restarted and now it wont go into recovery. what just happened?
It is just showing logo and I cannot get into Odin more either.
The tab had about 30% battery when it shut off and I cannot reach a charger for it for the next 4 hours.
Can I switch it off in any way to save battery?
the phone has switched off now. Is service center the only alternative? the tab was rooted with mokee installed.
devarshi84 said:
the phone has switched off now. Is service center the only alternative? the tab was rooted with mokee installed.
Click to expand...
Click to collapse
Try charging it when you have time and then try re flashing the stock Rom before taking it to service center
will the tab 2 charge without a recovery or ROM in place?
devarshi84 said:
will the tab 2 charge without a recovery or ROM in place?
Click to expand...
Click to collapse
I think it should
Ok, the tab2 is charging. thank you
I installed all the necessary drivers and odin and recovery on my laptop.
The tab2 is giving error on pc (this device wont start) mtp uSB. THe tab is stuck at 'samsung p3100' logo.
If it is any help, I have a working p3100 also running on stock firmware.
what should be my next step? I think I can manage if only I can get odin to recognize my phone or get into recovery (both of which seem to be missing.)
devarshi84 said:
Ok, the tab2 is charging. thank you
I installed all the necessary drivers and odin and recovery on my laptop.
The tab2 is giving error on pc (this device wont start) mtp uSB. THe tab is stuck at 'samsung p3100' logo.
If it is any help, I have a working p3100 also running on stock firmware.
what should be my next step? I think I can manage if only I can get odin to recognize my phone or get into recovery (both of which seem to be missing.)
Click to expand...
Click to collapse
Try reinstalling drivers
@shsagnik : Thank you very much for helping out.
I got installed all drivers by using the other P3100. But when I connect the bricked p3100, pc doesnt install MTP USB drivers. Under device manager it says " failed to start".
ODIN doesn't recognize it. either.
My mistake was I flashed everything on the phone including the internal memory.
PS: Can I force ODIN to recognize my phone?
Ok, my almost bricked device is back and runnning.
This might just help somebody. but my android handset was on a logo only mode. something in the combination of
Attaching it to pc (windows 7 64-bit)
re-installing and rejigging drivers
trying to let ODIN identiify
connecting via Samsung kies (I also tried restore on kies).
connecting a working android phone instead of the dead phone with pc to find and install drivers.
worked.
PS: I also let it sit dead powered off (worked only when charger was attached) for a whole day before trying to boot into recovery or bootlaoder (both worked).
devarshi84 said:
Ok, my almost bricked device is back and runnning.
This might just help somebody. but my android handset was on a logo only mode. something in the combination of
Attaching it to pc (windows 7 64-bit)
re-installing and rejigging drivers
trying to let ODIN identiify
connecting via Samsung kies (I also tried restore on kies).
connecting a working android phone instead of the dead phone with pc to find and install drivers.
worked.
PS: I also let it sit dead powered off (worked only when charger was attached) for a whole day before trying to boot into recovery or bootlaoder (both worked).
Click to expand...
Click to collapse
Awesome, now please change the title to solved
Can anyone please help. im stuck in a difficult problem. I cant enter recovery, my phone just loops, and i cant connect it to my pc. Just getting USB device not recognized. The last usb device you connected to this computer malfunctioned, and windows does not recognize it. I dont know how to add a new software or restore a backup, and i got a seious battery drain issue. Hope someone can help me. Im on Slim X rom on a E6653.
Download a MM, LP or Nougat firmware.
Let the phone charge and go to flashtool
Load the firmware you downloaded check all the wipe section case and put your phone on flashmode (vol - and stick USB cable while maintaining vol -)
Let flashtool do it's work and once done it should be OK
I have tried that, but my computer cant fin my phone, so i cant use flashtool
I found out of it. Had a faulty usb cord. Im happy again.
Hehe no problem