i flashed my sony ericsson xperia ray with an ics updated which said it was pre rooted and once i was done its stuck at boot and it does not even look like its in boot loop!
i factory reset it
cleared partition
cleared dalvic cache
and then installed from sd card
i also tried to connect it to the comp to flash a official ics update but the usb debugging is OFF
is there any way that i could turn ON the usb debugging from command prompt??
if its at the wrong section please do put it in the right section
thanks in advance
Did you try using flashtool to flash the stock Rom for Ray?
Or even SEUS?
Sent from my MT11i using xda premium
Ghostfreak NB said:
Did you try using flashtool to flash the stock Rom for Ray?
Or even SEUS?
Sent from my MT11i using xda premium
Click to expand...
Click to collapse
it was a zip file so i installed it from sd card!!!
amir4206 said:
it was a zip file so i installed it from sd card!!!
Click to expand...
Click to collapse
when i connected it to flashtool is said usb debugging is off!!
What about SEUS?
Did you try that?
Sent from my MT11i using xda premium
A few way to ressurect your phone :
Unlock its bootloader,flash a custom pre-rooted kernel,and flash a custom rom that are compatible with the krrnel,and hope your device can be turn on normally
Sent from my LT28h using xda premium
Ghostfreak NB said:
What about SEUS?
Did you try that?
Sent from my MT11i using xda premium
Click to expand...
Click to collapse
i used flashtool but connected in a flash mode before i connecting it ie vol(-) while connecting the usb and was able to flash a stock rom
Related
Hi..People.
Yeaterday i changed the model , product name of my Xperia U (Unlocked+ rooted) using build.prob editor. After trying to reebot the phone doesn't boot up. Only Sony Logo is showing up, and phone get restarted. Is there any way to get back my phone. I my usb debugging is not turned on,,,,please help!!!!
Throw a new Rom on your sd card then flash it, it should come with a new build.prop and hopefully fix your problem
Sent from my SGH-I747M using xda app-developers app
Custom rom flashing using CMD
j.kelly said:
Throw a new Rom on your sd card then flash it, it should come with a new build.prop and hopefully fix your problem
Sent from my SGH-I747M using xda app-developers app
Click to expand...
Click to collapse
I tried to instal KA 03 xperia S speed rom..
When flashing it with flastool cmd, the command written by the developer, says "fastboot flash system XperiaSspeed.img"
But when typing it cmd says that " xperiasspeedimg cannot be found".
I browsed the folder and no file ending with the .img found. (The developer asked to extract and flash)
I've never done a Xperia but I believe you should still be trying to flash a full.zip not just an img I would download a full Rom and flash the whole new zip......... is this you first Rom?
Sent from my SGH-I747M using xda app-developers app
Use flashtool to reinstall your ROM.
Sent from my LT26i with Tapatalk 2
Thank you guys
Thank you guys, the issue is solved...had to read about 22 pags of a thread..the Img file has to be installed using fastboot, and .zip shoulp installed using recovery mode..the phone is working..thank you guys also xda!!
As the title said,since the ROM had blocked alot of my Nexus S main function(unable to connect Wifi,unable to connect to PC),now I even sta\uck in the boot screen.So I decided to remove it,to recover it back to my Android 4.1.2 But,I don't know how to. Can anyone tell me the steps to remove it?Please reply me ASAP,since I only have this phone,and I survive without my phone
What rom did you install dude ? Does your fastboot work ?
Sent from my Nexus S using xda app-developers app
raducux said:
What rom did you install dude ? Does your fastboot work ?
Sent from my Nexus S using xda app-developers app
Click to expand...
Click to collapse
Thanks for your reply,the ROM I flashed is from this link:http://forum.xda-developers.com/showthread.php?p=27027809#post27027809
I can enter fastboot mode.
And have you tried flashing factory images ? My sd card got stuck once too from flashing and this was the only solution that worked...
Sent from my Nexus S using xda app-developers app
raducux said:
And have you tried flashing factory images ? My sd card got stuck once too from flashing and this was the only solution that worked...
Sent from my Nexus S using xda app-developers app
Click to expand...
Click to collapse
Flashing factory images?Which type of images(I'm bad at this sorry >.<)
Okay,problem solved.Using the "ADB push" method will do.By following this guide:http://forum.xda-developers.com/showthread.php?t=1667929 Just simply push the ROM into the SD card through fastboot mod,and flash the ROM,then everythings work fine.The ROM I used is Nexus S original ROM download from net.
All credits go to brwetz and xboxfanj:good:
Root and CWM for Xperia J Finally!
Thanks to srl3gx and Bin4ry for their awsome work!
and ME for taking risk!
Make sure u are in 11.0.A.3.28 or 11.0.A.3.18 firmware ALONE with Locked Bootloader..
This method Dosent Work on 11.0.A.7.5 Firmware! (working on it! )
for .28 firmware download from here and flash it
if u dont have a flash tool download it from here for windows and install drivers located in C:\Flashtool\drivers (choose all drivers)
since flash tool does not have xperia j drivers..u may hav flashing problem...for that
1.download and extract d ST26.zip ive uploaded
2.open flash tool
3.click devices>import
4.navigate to d file u've extracted
5.now xperia j driver is installed
u can now flash without problems
Now back to rooting...
Root first! thn apply CWM!
Steps for Rooting:
1.extract Root_J.zip
2.make sure 'usb debugging' is enabled in devolpment settings
3.double click Runme.bat file for windows users...runme.sh for linux users
4.wait for process to finish (mostly should work)
Steps for CWM:
1.extract CWM_J.zip
2.'usb debugging' on
3.double click 'install.bat' only for windows (linux not working! my bad..)
4.wait for it.....installed! close the shell program and switch off the phone..
Plug in charger or USB....the phone switches on....press up and down volume keys repeatedly when SONY logo flashes.....voila u get into CWM!
You need plugged in charger or USB to goto CWM! Else CWM wont Work!!
reboot to system and see if supersu is installed finish! ur phone is rooted and cwm is installed !!
CWM has little bugs ..but its a never mind stuff..
use arrow keys to navigate..power button to select and 'go back' option in cwm itself to go to previous options.
Comment if it worked for you...let others know!
Tested on my xperia J and Miro
Dont restore factory setting or else CWM will vanish...n u hav to reflash whole firmware again
for questions and problems ask srl3gx
HOPE I HELPED...hit thanks
Sorry for the last update! It Dindn't Work for many devices!
wow finally it arrived.
Anyone tried this already?
Sent from my ST26i
Yes dude I tested it.. It works... That's y i posted it
Sent from my ST26i using xda premium
kishenpj21 said:
Yes dude I tested it.. It works... That's y i posted it
Sent from my ST26i using xda premium
Click to expand...
Click to collapse
Followed your instructions on my Experia J. I have build 11.0.A.3.18 (UK on orange/EE). I decided against flashing to 3.28 and to try with 3.18, but to get the Flashtool working I did the following:
Once the ST26.zip file is extracted (using Winrar) I then have to open this extracted file again in WinRar to get the files that should live at C:\Flashtool\devices\ST26 (loader.sin etc.). I then had to copy the original file ST26.ftd to c:\Flashtool\devices. I enabled USB debugging in the Developer settings on the phone and Flashtool started working properly.
I was able to root and CWM the device as per your instructions on buiild 11.0.A.3.18. Cheers.
The major problem with this CWM method is that it's designed for the Tipo, so when you try to flash a zip made for jlo, it fails. I had to remove the assert from the top of the scrip to flash with this.
Thanks for trying on .18 firmware... I'll update d thread
Sent from my ST26i using xda premium
adfad666 said:
The major problem with this CWM method is that it's designed for the Tipo, so when you try to flash a zip made for jlo, it fails. I had to remove the assert from the top of the scrip to flash with this.
Click to expand...
Click to collapse
Dude dunno y u have problems with CWM...btr to flash according to my instructions... It works for many
Sent from my ST26i using xda premium
kishenpj21 said:
Dude dunno y u have problems with CWM...btr to flash according to my instructions... It works for many
Sent from my ST26i using xda premium
Click to expand...
Click to collapse
Have you tried flashing a compiled ROM? It fails as the CWM thinks it's on a Tipo device.
Plus if you wipe your system partition, you lose CWM, it's not a good solution. I've posted a CWM as a boot.img in my CM10 thread
adfad666 said:
Have you tried flashing a compiled ROM? It fails as the CWM thinks it's on a Tipo device.
Plus if you wipe your system partition, you lose CWM, it's not a good solution. I've posted a CWM as a boot.img in my CM10 thread
Click to expand...
Click to collapse
Oh..ok.. But this post is for original firmware rooting n CWM... Won't work for custom roms
Sent from my ST26i using xda premium
kishenpj21 said:
Oh..ok.. But this post is for original firmware rooting n CWM... Won't work for custom roms
Sent from my ST26i using xda premium
Click to expand...
Click to collapse
OK, plus this will work for people who cannot unlock their bootloader. But perhaps you should put a warning as some people may want to wipe their system partition before they restore a backup (which will work) but if they for what ever reason try to reboot the phone they will be lost and will have to restore via flashtool!
thanks for report...updatd
very good work thx!
It's recovery from Tipo thus works like work: (
Pacjonek said:
It's recovery from Tipo thus works like work: (
Click to expand...
Click to collapse
sorry! cant get u!
Is this works with unlocked bootloaders '?
Sent from my ST26i using xda app-developers app
rachit7 said:
Is this works with unlocked bootloaders '?
Sent from my ST26i using xda app-developers app
Click to expand...
Click to collapse
Ya wil wrk but y do u want to unlock boot loader... Ready to lose warranty???
Sent from my ST26i using xda premium
I've updated my xperia j to firmware 11.0.A.7.5 and now i can't root it with this method...
Any help?
Yea im the same 11.0.A.7.5 cant you flash the phone with older firmware?
Okay i flashed that firmware from first page and now my phone is rooted thanks alot
If we can get ftf file of 11.0.A.7.5 firmware and flash it with Flashtool without wiping data (just wiping cache) maybe we don't loose root... but where can we found that ftf file???
Hello
My HTC J Butterfly is currently in a state where I cannot use ADB (cannot install USB drivers):
http://forum.xda-developers.com/showthread.php?t=2417098
Is there any way to install ROM without working ADB/USB ?
Of course if there is a way to fix the ADB/USB that would obviously help as well.
Thanks
Download the ROM on to your phone and install, that's if you have a working recovery.
Another way is OTA
Sent from my HTC Butterfly using xda premium
bluheart said:
Download the ROM on to your phone and install, that's if you have a working recovery.
Another way is OTA
Sent from my HTC Butterfly using xda premium
Click to expand...
Click to collapse
Unfortunately I cannot download anything to the phone, because there is no ROM.
Bootloader and recovery are working fine.
Any other ideas ?
Thanks
deleted (see the link in OP for progress)
jko76 said:
Unfortunately I cannot download anything to the phone, because there is no ROM.
Bootloader and recovery are working fine.
Any other ideas ?
Thanks
Click to expand...
Click to collapse
Take out the sd card and use an adapter then plug the adapter with the sd card in it in the computer and transfer the Rom on it. When Ur done take sd card from out of the adapter then out it back in the phone and flash the Rom then attach the phone bk to the pc if your not s off and put it in fastboot then flash boot image extracted from Ur Rom
Sent from my HTC Butterfly using XDA Premium 4 mobile app
Use sideload option
Sent from my HTC Butterfly using xda app-developers app
daorderdillon said:
Take out the sd card and use an adapter then plug the adapter with the sd card in it in the computer and transfer the Rom on it. When Ur done take sd card from out of the adapter then out it back in the phone and flash the Rom then attach the phone bk to the pc if your not s off and put it in fastboot then flash boot image extracted from Ur Rom
Sent from my HTC Butterfly using XDA Premium 4 mobile app
Click to expand...
Click to collapse
I have flashed Droid DNA ROM to the phone. Since Droid does not support External sd card I cannot use the method you described.
Bassie39 said:
Use sideload option
Click to expand...
Click to collapse
It seems that the sideload option does not work either. Maybe it needs working ADB interface ?
hello ..
i tried unlocking bootloader.
after that the device is stuck on the animation screen.
i read this thread and then decided to flash stock firmware
http://forum.xda-developers.com/xperia-l/help/boot-unlocking-bootloader-t2440526
now when i connect my device via flash mode n try to flash stock via flash tool .. after 5-10 secongs the mobile wud go into charging mode and restart. the flash wud be cancelled and it wud say tat the drivers for the device are not installed..
help
m stuck
Try to install driver or try another USB port
Sent from my LT25i using XDA Free mobile app
harrymason37 said:
Try to install driver or try another USB port
Sent from my LT25i using XDA Free mobile app
Click to expand...
Click to collapse
thnx it worked.
i fashed and restrted it..
now while installing cwm via cmd.
its giving an error that
system/bin/sh :su: not found
plz help..
You're not rooted try this:http://forum.xda-developers.com/showthread.php?p=53756829 and install superuser
Sent from my LT25i using XDA Free mobile app
max8824 said:
thnx it worked.
i fashed and restrted it..
now while installing cwm via cmd.
its giving an error that
system/bin/sh :su: not found
plz help..
Click to expand...
Click to collapse
I wonder why you are installing cwm via cmd when you have an unlocked bootloader.