I searched all over google and other fourms here, but no luck, here is the problem:
I wanted to flash an Arabic ROM on my HTC vox (s710) , I flashed first the Vox's ROM (RUU_Vox_HTC_WWE_1.34.405.1_4.1.13.54_03.10.90_Ship)
and it worked great, but found out that there was still no Arabic support.
I got this ROM (HTC_Excalibur_ARA_1.15.415.11_4.1.13.41_02.88.90),
as I thought that the device was already unlocked, it would accept any ROM for any device, turns out it doesnt.
Just before the flashing is over, it gave me an ERROR : FLASH WRITE, and my HTC just went dead in a heart beat.
Know the phone has that Green LED at the top on, as long as its connected to the laptop or to the battery, but just wont boot - DEAD
(P.S -- When connected to the laptop, something activates but still cant access the phone)
I tried booting in safe mode by pressing and holding the camera button and connect USB cable, but doesnt work, tried couple other stuff but still no difference. Please I need help , is there something I can do ? is it dead forever or can it be still fixed
Sad - you flashed an Excalibur ROM on a VOX - so the Vox is plain dead
While the devices are quite similar (same chipset and even same NAND storage) it still seems that the bootloader is not identical and this is killing any further access.
In theory you could flash via a JTAG physical connection but this is for true HW freaks and you also need special HW + SW to do so.
Bypassing the CID check (with USPL or JumpSPL) also kills all sanity checks in the bootloader (SPL) that prevents cross-device flashing (and a dead device after doing so).
tobbbie said:
Sad - you flashed an Excalibur ROM on a VOX - so the Vox is plain dead
While the devices are quite similar (same chipset and even same NAND storage) it still seems that the bootloader is not identical and this is killing any further access.
In theory you could flash via a JTAG physical connection but this is for true HW freaks and you also need special HW + SW to do so.
Bypassing the CID check (with USPL or JumpSPL) also kills all sanity checks in the bootloader (SPL) that prevents cross-device flashing (and a dead device after doing so).
Click to expand...
Click to collapse
So I am doomed, or is there another easy way to reflash it or something.. If i took it to the nearest HTC center, would they be able to do something or not ?
There are ways to reflash, but all rely on the SPL being OK. Sadly this is what you killed with the wrong ROM - so there is no hope. I believe that service centers just use the same USB connected SW upgrade via SPL - there is no reason to have any dedicated HW devices as normal users cannot kill their device the way you did.
A glimpse of hope could be that only the USB and LCD access is wrong and the SPL would work otherwise - not very probable though. Is the device still charging? Do you see orange and green light when connecting to charger?
If so then you may search for the upgrade via the "Gold Card" method. This is a specially prepared (some key in the bootsector of the card) sd card which has the .nbh file stored in root directory. Boot + SW upload would follow a special sequence then which you would have to execute "blind" as LCD does not work. Again: I doubt the SPL is ok enough and the "blind" upgrade would have its own challenges.
Actually I went to the service center today and I was surprised when he said that he was going to perform a JTAG. Didn't really know that they could do that, but yeah.
Thanks anyway.. Just for future reference is there an Arabic ROM for HTC s710, because i searched the internet for over a week and didn't find one.
wow, this is great service - just tell what they will charge you for that - and how long it takes. Maybe they send it to some special center where they can do that, so it takes time.
Do they have an Arabic ROM for the Vox which they could put there?
Related
My phone is die because turn off PC when uprom ?
It's not turn on , not signin bootloader... Hepl me
No bootloader = gone
Someone tried to pry open the phone to JTAG the ROM but they reported back that a metal cover is protecting the ROM chip from being JTAG
So conclusion, sell your phone for scrap
thank u so much but i tried open my phone but haven't got Rom chip (Flash chip ?) replace it. i'm live in Vietnam. JTAG is what??? i don't known.
blackpuck said:
thank u so much but i tried open my phone but haven't got Rom chip (Flash chip ?) replace it. i'm live in Vietnam. JTAG is what??? i don't known.
Click to expand...
Click to collapse
If you can't get to the bootloader, your phone is dead. Give it up.
noone can help me ????
I don't think anyone can help. Since there is no bootloader, you cannot do anything. Plus you wrote that you have SDA2, which is not HTC Tornado.
I assume you also can't perform a hard reset?
http://en.wikipedia.org/wiki/JTAG
JTAG is a (physical) connection to the ROM chip to program it. You need special equipment and expertise to reprogram your phone this way, but if it's dead otherwise why not give it a try and open your phone .
Be sure to make some pictures and post them here .
Or go back to the store, try to look really innocent and have the manufacturer fix it for you (this probably won't work btw).
Someone tried to JTAG but the ROM chip is blocked by a metal cover
Hi... I have 2 sda tornado phone but I want to do one
hi...
please I would like remplace a rom (os) chip because I have a brick (white screen) tonado and another that is broken the mainboard..
bur If I know which is the chip flash I could be remplace and have one good phone..
thanks...
I have a silly question.... When you place connect your phone to your pc... Does windows do that sound as recognizing that something was connected? If so... Try to flash the T-Mobile SDA Ship ROM. You don't need to be on bootloader to flash a ship rom, as long as windows recognizes that something is there. The "enter boot loader" in the Rom Flashing will take care of that. At least.... it happend once for me when I was sure I had bricked my SDAII. Also, My SDAII does say its a Tornado. However, I have read many say that SDAII's are not tornados. Confused.
hi... the problem is that when I connect to pc, the pc can´t recognize... can´t acces to bootloader just I have a white screen.... I´ve tried with activesync, mtty, TeraTermPro but nothing....... first I upgrade to windows 6.1 perfect english and all perfect (I unloked the phone, I follow all steps to upgrade the phone and works) but the problem is the when I tried to downgrade to t-mobile official rom....
When you place connect your phone to your pc... Does windows do that sound as recognizing that something was connected? NO
If so... Try to flash the T-Mobile SDA Ship ROM. You don't need to be on bootloader to flash a ship rom, as long as windows recognizes that something is there. i CAN´T ... DON´T RECONIZE
The "enter boot loader" in the Rom Flashing will take care of that. At least.... it happend once for me when I was sure I had bricked my SDAII. Also, My SDAII does say its a Tornado. However, I have read many say that SDAII's are not tornados. JUST WHITE SCREEN AND CAN´T ACCESS TO BOOTLOADER O REBOT THE PHONE... I THINK THAT I damage THE SLP (BOOTLOADER)
Confused.
Hello XDA Nice Team !
By mistaken i wrote some file to my bootloader in my I-Mate Jam ..
That was after using the bad ROM : 2.03
it's the worst cooked version i saw !
Now my bootloader mode is working .. but no way to connect to PC with USB port ..
My computer does not recognize my Magican when plugged in bootloader mode anymore!
Bootloader Ver: 1.0
is there any way to fix or upgrade or restore original bootloader
Now i cant upgrade or downgrade my magican by any method
Noway to use successful connection with any roomupdate utility
Please help me to fix or restore my bootloader!
Thanks to any one read or replay or try to help or help me to resolve my problem
XDA lover
i'm sorry that happened mate...
i've had success with flash-from-bootloader attempts before, both on my Magician, when i accidentally flashed off of Vista and it'd enter the bootloader every week or on a reset using the reset hole, and also on my Wizard when i ignored warnings from WM5torage and it'd only enter the bootloader
what precisely happens when you connect to the PC, allow USB connections in AS/MDC, and let the phone enter bootloader however it does? i can just flash a rom from there, but i won't (iirc) get any reports of as recognising the device...
My experience:
1- when i plug my sd card into my jam .. usb not recognized in bootloader mood !!
2- when i use puty or roomupdate it reaches to USB> then when i type any command it does not respond !
3- i could do something .. i let my phone bootup and this i-mate logon screen stays 4ever .. i connected my ppc to pc and i could explre my imate by activesync ...
i could reach something .. when i explore my phone and remove everything from startup folder .. my phone boots .. and i can see start botton .. no touch alignment comes .. and everything works .. but.. screen is virtually reversed .. i can see the OK botton but i must click on the facing area and it be clicked ..
i think i executed some wrong hard SPL to my phone ant that happened >
is there any way to resolve this problem?
is there any way to erase flash on my I-Mate Jam????
is there any way flash my phone?
i also have prepaid JAFWM with pkey and USB cable .. no BOX ..
Help please!
that's messed up... howsabout flashing it at the point when the phone boots up? if there's an AS connection there, then it may work... i'd flash to an official rom though
Same problem , PLS Help !!!
Thx for help
You should check USB connection I think...
Try plug your battery out of device and wait a moment (e.g.10 minutes) and try again,sometimes it will be fine when you did this.
If your magician isn't detected at ALL by your PC when plugging the USB cable into it (i mean, no new hardware; no unrecognized hardware; nothing is detected in your PC when you plug the USB cable), and unless you had previously made a SD backup of your entire Flash with this procedure ( http://wiki.xda-developers.com/index.php?pagename=MagicianSDflash ), then your only option will be to build a JTAG diag cable:
Here are some general directions / ideias:
Magician JTAG pinout: http://wiki.xda-developers.com/index.php?pagename=MagicianJTAG
How to build/run the JTAG: http://wiki.xda-developers.com/index.php?pagename=DeadBoot
Photos : http://www.cf-box.com/htm_data/55/0912/1679.html
Some interesting stuff for debugging problems: http://pda2u.ru/ptopic205.html
For sure cotulla has one built so to test his ROMs + bootloader - maybe he will be willing to give you some directions if you run into problems, and above all, give you a prepared .nb0 (with the bootloader file) for your magician, which i do not know if there's one out there, extracted from an original ROM.
Anyway, you can always try and do it for yourself using itsme utilities. Follow this link: http://forum.xda-developers.com/showthread.php?t=218643
Regards
Keeper,you're awesome! I'm searching for JTAG,too
xiaojin1985 said:
You should check USB connection I think...
Try plug your battery out of device and wait a moment (e.g.10 minutes) and try again,sometimes it will be fine when you did this.
Click to expand...
Click to collapse
Dear xiaojin1985 ,
Thx for your help, But unfortunately i tried your solution but it dosnt work !
Dear Keeper,
Thanks too for your help,
and i think the solution for my problem is one of the solutions you says ( How to build/run the JTAG: ) ,
but the pictures is not available anymore , so pls can you get the pictures ?
All the pictures are in here:
http://s218.photobucket.com/albums/cc23/alex_beda/ and in attachment there's a .mth file with all the pics built-in.
Don't take it wrong what i'm about to say, but in all honesty if you can't figure this out yourself (digging up the internet for the missing pics), i would suggest that you shouldn't try this, since this ain't easy at ALL...
Just to give you some ideias, it will require you to adapt your magician test point signals (TDO;TDI; nRESET; etc,)seen on the magician pinout pic to what is said; solder very thin wires (best done with a small hot air tip); fixate the small dip switch (micro switch) to be always on; keep the USB connected...idk... plus alot of other small details which ain't easy to accomplish.
Personally i haven't tried this yet but for sure it would work
If you decide to go ahead, please post some results!
Connection error solution
this is my problem
hi all. A friend of mine gave me an S100, and after i played for a few days with it, i decided to update it's rom. A "country error" problem appeared,cause i have the greek version, so i ran MaUpgradeUt_noID.exe which completed (as showed 100% process). My (new) problem is that i cannot update anymore. Every time i enter boot menu, i ran the upgrade
(HTCMAG_ROM_WWE_O2.rar) following all the steps normally. When the device resets (so the upgrade is going to start), it's re-reseting again and showing ERROR 101 connection error. Any ideas?
Qtek Greek version
R 1.12.00
G 1337.42
D 1.12.00 WWE
P.S. apart the problem everything is function properly
and the solution
hard reset
plug usb (uncheck allow usb connection in activesynch )
run MaUpgradeUt.exe radio_1.11_greek but idont reset the qtek in first screen
and upgrate downgrate start all ok
reset
welcome screen
hard reset
plug usb (uncheck allow usb connection in activesynch )
run MaUpgradeUt.exe MagicianRadio_1.12.10. uk but idont reset the qteki n first screen
upgrate from radio 1.11 to 1.12.10
reset
welcome screen
hard reset
plug usb (uncheck allow usb connection in activesynch )
run HTCMAG_ROM_WWE_O5_251209
everything is ok my magisian run the new Rom
here..........................
probably, i dowgrade my kaiser with lower version...(everything passed(unlock,flash)without problem and error...
after flash phone dead... nothing happen when try to power on,reset,boot,anything...try,almost 4 hour, everything what can find here, but still no luck...
no power, no bootloader, even i can't do anything with mtty couse i run Vista, and have prob to stop activesync working... everything what i got is
ZTE diagnosstics interface 6000 cdma 1x(com5)
zte nmea device cdma 1x (com6)
in my control panel/device manager,
that talking maybe phone is not totaly damage...
anyone help, any idea...this will be long long night...
I'm not sure what you mean exactly but I also had a dead Kaiser. It did not happen after flashing but my phone suddenly turned off and could never be turned on again. I first thought it was a battery issue but no.
Finally I returned it to HTC and they replaced the motherboard under warranty.
yes but my kaiser is not in warranty, customer buy it in Italy... and I kill him, sad but true...
well i might not be correct, bu it looks like you wiped the nand on the phone... i think if you look up the steps in the frankenkaiser thread it should help you out
but i can't go in bootloader mode....
if you look you dont have to enter bootloader mode..: http://forum.xda-developers.com/showthread.php?t=394584
ok, first , from now i'm on XP...
but always same... when attach in any button combination to the pc, it was always see the same, look on the pic
and in MTTY, i have the port from 1 to 10 &usb. on usb cannot connect, with the error "usb port can not open"
btw forgot to write, device is brand new, no hw damage
i make connection between kaiser and MTTY, over diagnostics port, but when try to type command(or Enter) nothing happens. how to use MTTY
as i see my kaiser stuck in download mode... (see in QPST & QMAT)... how to flash it or to restore it to normal mode(phone no power on, no going to boot mode)... i read emi&sbi, if it can help some...
if you look here from step 3 down i think this should walk you thru the process... http://forum.xda-developers.com/showthread.php?t=393337
if you look at the part right below step 2 it says to lower your com port for the diagnostic interface below 10, i think i saw that yours is set to 53...
i try on 3 differnet pc. try all comm port. mtty is my problem(one of them). when run mmty(choose connection base on diagnostic port), i can type anything, any command, enter,etc... nothing on screen, nothing happen after enter...
can someone explane how to flash kaiser via jtag...
someone who allready do it...
or send me to pm
Sorry no idea!
Hi mobilend,
i just saw your message... no idea about that!
Don't know if anybody already traced the testpoints.
You also would need some software tools to access the MSM chip.
Maybe i'm wrong but i read some threads about this kind of brick and maybe your able to recover without JTAG.
Perhaps the kaiser cracks could help you out
Regards,
scholbert
i do nothing since today...
if somebody have idea how to unbrick kaiser with jtag, write here or i may send device to him...
Problem
Hi excuse you have succeeded there?
I have yours same problem.
This is my fear, for this reason I have not had the courage to update my ROM.
I do not understand, the videos appear to be so simple, but at the same time, to read topics like these, I am in panic ...
Will I still be aware and courageous enough to update my ROM?
jonastamborin said:
This is my fear, for this reason I have not had the courage to update my ROM.
I do not understand, the videos appear to be so simple, but at the same time, to read topics like these, I am in panic ...
Will I still be aware and courageous enough to update my ROM?
Click to expand...
Click to collapse
Most of the problems come from not reading the information...
If you look at the number of users on here that have managed to upgrade their phone you will see that it way outways the number of people who have truly bricked thier phone. (A lot of the people who have upgraded thier phone have little knowledge about what unlocking means as well, so don't worry if it's a bit overwelming).
If you want to get started click "KAIS: Getting started" in my sig for a step by step guide by mskip. mskip, myself and some other members will help out with any questions you post in that thread. Also check out the info on the HTC Kaiser wiki page on the xda-developers wiki page.
Ta
Dave
Hi there, I tired to issue my problem in some other threads, but without any response so far - probably my problem is more specific.
I was using AHEN 6.5-R6i Rom for few weeks when some time after charging my Raphael was not powering up at all. I presume no relation between Ahen rom and the problem (as described further).
I bought new battery and it occurred that probably power charging circuit was damaged, because it newer completed charging, the device was always very hot and discharged in few minutes even when turned off (until completely drained out). What is more the USB connector works only for charging (maybe damaged data connection circuit?).
As a result, before returning the device for guarantee servicing I wanted to downgrade all the roms to the original ones. As advised I started with Radio and OS stocks, but after bootloader update (from SD card, cause my USB doesn't work) I got only "upgrading ROM code error" and the device tries to load some ROM, but putting any on SD card doesn't work anymore.
Any suggestions how to cope with this situation?
If you need help please provide us with important information. So fill your signature first. Mainly if you have hard-spl or if you bought olipro cid unlock and what exactly you have done until now. Also wether your device is CDMA or GSM? If it is GSM than you have to first restore Stock Radio first, after that if you cid-unlocked the phone you have to relock it again. Than remove hard-spl and install stock ROM. But if your USB is broken, i think there is no chance to remove Hard-SPL neither to restore to stock. Remember that when you are in a bootloader and you do not see that the device is connected to activesync or Windows Mobile Device Center it does not mean that it is not connected. Just check you hear the sound indicating that something is connected to usb in vista or windows xp.
If you need help please provide us with important information. So fill your signature first.
=> done
Mainly if you have hard-spl or if you bought olipro cid unlock and what exactly you have done until now.
=> chnged SPL to OliNex, OS to AHEN 6.5-R6i, Radio to version required by AHEN rom
Also wether your device is CDMA or GSM? If it is GSM than you have to first restore Stock Radio first, after that if you cid-unlocked the phone you have to relock it again. Than remove hard-spl and install stock ROM.
=> I retracked the changes as indicated changing both radio and OS to original ones, but had just problem at last step = flashing oryginal SPL (because I made it from SD).
But if your USB is broken, i think there is no chance to remove Hard-SPL neither to restore to stock.
=> Hmm, anyway right now I am stack because bootloader is "loading ..." every time I reboot the device.
Remember that when you are in a bootloader and you do not see that the device is connected to activesync or Windows Mobile Device Center it does not mean that it is not connected. Just check you hear the sound indicating that something is connected to usb in vista or windows xp.
=> I tried to use some terminals to see if I can execute commands directly or see any output, but I haven't even succeeded to open the port. Maybe I am doing something wrong - I give it a try once more tonight.
So what version of SPL is bootloader showing? If it's showing something like 1.90.0000, you are in bootloader and USB circuit is not damaged you should be able to normaly flash ROM from your provider from bootloader. So download the ROM from your T-Mobile it should be some exe. When you see bootloader tricolor screen coonect usb cable from Touch Pro to computer and run the exe soubor with your desired ROM. It should work if everything is OK!
If your device is showing 1.90.OliNex, than i cant help you because i do not know how to remove Hard-SPL from bootloader, maybe it is possible, but for more experienced tech guy, who i am not
PS: Hope you did not bricked your device because Hard-SPL and removing Hard-SPL is all done with cable, you cant do it from SD, and you cant flash original SPL before removing Hard-SPL!
hmm, it seems that I have managed to flash, at least partly, the original SPL from SD card, cause it shows version 1.90.0000. Partly, because it states that the previalus rom update was not successful :-(
In this state (in boot loader mode) I can't even charge battery so I have to do it externaly. Connecting to PC doesn't work (PC USB and cable are fine). The only thing that change after connecting to USB charger is that device gets hot ...
i am sorry to say, that you probably bricked your device... Maybe someone could help with more advanced hardware, software support, but i am not the right person...You can try to put your device to service and hope they will not recognize what have you done, but it depends on your stock SPL version. I got czech T-Mobile and stock SPL was 1.69.0000, so maybe yours was the same...
Next time please read more carefully, search or ask someone if you are not still sure, things about flashing SPLs are very dangerous if they are not done carefully...
Can anyone help this guy? He tried to flash original SPL over Hard-SPL, and therefore it is not looking very well for him to unbrick his Touch Pro...
So ... I got it from the service and they changed the motherboard and the battery, no charges
It was brickes, because of cherging circuit issue.
Unfortunatley I send it back to service, because the loudspeaker is not working ...
Actually I am the same exact boat as the OP. My phone stopped charging and its because the USB port is broken. I need to change the phone back to stock but if its not charging its probably not going to get a connection to the computer either. I read that on at least the Hermes it was possible to flash from the SD card. This is not possible for the TP? Thanks
riotburn said:
Actually I am the same exact boat as the OP. My phone stopped charging and its because the USB port is broken. I need to change the phone back to stock but if its not charging its probably not going to get a connection to the computer either. I read that on at least the Hermes it was possible to flash from the SD card. This is not possible for the TP? Thanks
Click to expand...
Click to collapse
You can flash the ROM, radio, splash screens etc etc from SD card - you will then have to send the phone back with hard spl still installed as you need a usb connection to remove it.
Dont assume you cant get a usb data conenction though - try it and see!
I did try the connection, didn't work. How do you flash from the sdcard? I just dont want to brick it.
Please read this thread on how to flash (including how to flash from SD card).
Again, (assuming you have the correct hard SPL currently flashed) you can flash a ROM, radio & splash screens etc to your phone from the SD card (one at a time) but as previously said you need a USB connection to flash hard spl (dont attempt it from the sd card).
So, my Raphael arrived from service after the second repair (loudspeaker not working) - it seems all works this time
By the way, that is correct that a USB connection is necessary to flash hard spl, but .. I was desperate because the USB was broken, so I tried it from SD. The effect was good enough for the service - the Hard-SPL seemed to be reverted to oryginal one, however the booting was stacked at loading the ROM
Well, I've updated few htcs before and everything went fine. But there's always the first time...
I upgraded my htc hd2 spl 1.42.0000 to hspl2, wanted to upgrade rom/radio too, but couldn't find any rom I do like, and then I got no more leisure to play with it. So there was only hspl2 replaced on the device and that's it. Everything was fine for a month or two, then suddenly the phone function stopped to work (couldn't register into network anymore). Wanted to send back to factory for repair, but to avoid warranty loss I wanted to downgrade the hspl to stock spl. Downloaded stock image at htc site (was 1.48.something), did everything exactly in a way described in the video tutor, and - got stuck on light gray "Loading..." screen after the colourful one, and nothing more. Tried to update ROM via activesync for test, got stuck at 0% and that's it (although the connection is fine), googled a lot, browsed a lot of xda-dev... still nothing useful found.
Technical info + what shows in the colourful screen:
Eastern Europe HTC HD2
PB81100 HX-BC
SPL-2.08.0000 8G XE
I would really appreciate if someone could tell me, what it is, and how to fix it!
Thank you in advance.
I believe when you did the original HSPL, you selected the wrong version. The SPLs that end with '.0000' are the stock ones. Assuming the HSPL was done correctly it should read "2.08.hspl". Try flashing HSPL again, this time select .hspl, then flash your ROM. Should be good to go.
Edit: When people say you need a stock SPL to send it in for warranty, Im not sure if you need the exact same one it came with or not. Because you basically just reflashed a stock one anyway, you might be able to just send it in for repairs as is, but Im not 100% on that.
donkeypunch85 said:
Try flashing HSPL again
Click to expand...
Click to collapse
Thanks for the tip and trick. Unfortunately, like I said this doesn't help, cause flashing doesn't work. Tried hspl2 and hspl3 as well. The screen turns 3-color, then gray "Loading..." like it was when flashing from sdcard, and stucking on it...
When installing hspl3, the software on the computer says (while having that "Loading..." screen on the phone):
CRITICAL ERROR
Flow: 00000001
Error code: 00000002
Description: USB Connect failed!
(although ActiveSync shows connected and sync/exploring runs fine)
I'm becoming really unhappy with this one.
What OS is on your PC? Are you making sure Anti-Virus is disabled before flashing? If Win7 right click on the HSPL and choose 'run as admin'. Your using a USB slot on the rear (main motherboard) of your PC and not one of the front ones right?
It suddenly started to work today. I have no idea, what happened, did the same steps as before. The GSM function is still broken, but now, as the flashing worked finally, I'm able to send it back for repair without a risk to lose warranty. Mystical.
Thanks anyway for your time and willing to help.
...had the same these days on an HD2 which I successfully up-/downgraded at least half a dozen times before.
Did the MTTY 29 thing (again, surely the 6th time, never had any problem before) and afterwards had the issue you describe.
What helped me was re-flashing the HardSPL. Afterwards all worked 'as usual'.
Hope that helps others, Franky
Ok
and if my usb plug is broken?
I can't flash from sd, because it stops on the 'loading...' screen. I even tried the gold card method and still stuck on 'loading...'.
Wat's even worse my current system is rather unstable and WM sees only 208mb of ram...
Any suggestions?
T-mobile HD2! Problem Flashing rom
Hi Guys,
I'm a new guy in this great site, because I bought a T-mobile HD2 recently, via china, and it's not a fake!!!
But I want to update its rom to put the android2.2 's system.
I have tried several methods find in this site. But during the rom's flash, my phone shutdown and the connexion between Pc and phone switch off.
The phone is only in sleep mode and not off.
Can you help me to resolve this problem?
My system :
Phone :
Not SPL on the bootloader (only tri color) and this message :
" Error :
Copying file from SD card failed.
The system will shut down"
OS : Windows mobile 6.5 Professionnel
Software version : DUMA.10X.W10.20.P29
Protocol Stack (software) version :
MAUI.09B.W10.16.MP.V5, 2010/06/07
Dual Sim, and no take off SD card storage
Rom version : v01.00
Rom Date : Sep 10 2010
Boot version 2010 08 01
PCB version v01
Model ID T8585 (Leo)
Manufacturer HTC
CPU QUALCOMM 8250B (1024 MHz)
Ram Size 576 Mb
Nand Size 1024 Mb
Data bus 32 bit
Memory CPU 194 Mo
Memory storage 385 Mo
Memory inside SD card storage 7362 Mo
PC :
OS Windows XP SP2
ActivSyn4.5 Ok, but not synchronization with outlook, but connexion between PC and phone is OK.
Use update Rom Flash : Rom T-mobile v3.14 (run OK, no problem until progress bar (phone in sleep mode).
I tried SD card's method, unless sucess.
I used qmax to find SD card's number. But the memory's value is 3,5 Gb and not 7,3G.
Well, I think, I have forgot anything!
Thanks for your help!
Best regard
If you can get to the bootloader (four color stripes) then do so and then connect the phone to the PC. Wait until word 'serial' changes to 'USB'. Then start update on the PC (normally click the _RUU_(...).exe and follow the steps).
If fails please write at what point.
htc hd2
tomus said:
If you can get to the bootloader (four color stripes) then do so and then connect the phone to the PC. Wait until word 'serial' changes to 'USB'. Then start update on the PC (normally click the _RUU_(...).exe and follow the steps).
If fails please write at what point.
Click to expand...
Click to collapse
it fails at 8%.