Database Info

[Q] my XT 720 bricked ><

hello all, yesterday i tried to edit the framewrok_res.apk to edit the status bar, but i forgot to change the r/w properties before replacing the system file.
After replacing, my XT 720 immediately shows black screen. and every time it stops at the M logo ...
I downloaded RSD lite as someone posted before, and the usb driver 4.6.5, but then RSD Lite couldn't detect my phone when i entered the recovery mode.
Could some one please kindly tell me how can i do><
sorry for my bad English

gn01222116 said:
hello all, yesterday i tried to edit the framewrok_res.apk to edit the status bar, but i forgot to change the r/w properties before replacing the system file.
After replacing, my XT 720 immediately shows black screen. and every time it stops at the M logo ...
I downloaded RSD lite as someone posted before, and the usb driver 4.6.5, but then RSD Lite couldn't detect my phone when i entered the recovery mode.
Could some one please kindly tell me how can i do><
sorry for my bad English
Click to expand...
Click to collapse
first u must install driver for xt720 and u must go into bootloader mode not recovery mode

metalizer2000 said:
first u must install driver for xt720 and u must go into bootloader mode not recovery mode
Click to expand...
Click to collapse
u mean the usb driver for xt 720?
is the screen with a big triangle indicates i am in bootloader mode?
thanks

gn01222116 said:
u mean the usb driver for xt 720?
is the screen with a big triangle indicates i am in bootloader mode?
Click to expand...
Click to collapse
Yes -- try freshly installed Motorola handset USB drivers. If you have a 64-bit windows 7, it may be a little difficult to get it working. Try invoking RSDlite in XP compatibility mode.
Big triangle is recovery mode. Bootloader mode is even terse. Power up with VOLUME_DOWN + CAMERA. It'll just print 1 liner to connect USB cable.

kousik said:
Yes -- try freshly installed Motorola handset USB drivers. If you have a 64-bit windows 7, it may be a little difficult to get it working. Try invoking RSDlite in XP compatibility mode.
Big triangle is recovery mode. Bootloader mode is even terse. Power up with VOLUME_DOWN + CAMERA. It'll just print 1 liner to connect USB cable.
Click to expand...
Click to collapse
ank
thank you so much, i finally flash back to the original rom><
now trying to flash another rom XD
big thanks!!

AP Fastboot Flash Mode not being detected on pc

I've searched the whole sight and tried a bunch of so called fixes and still when i plug in my atrix 2 in boot mode (only it boot mode it does this) all i hear is instead of the dehdo that lets u know its connected i hear duhduhduh and RSD doesnt detect my device... im trying to fxz to 2.3.5 then ota upto ICS then root but i cant do any of these because of this please help.

greatanomaly said:
I've searched the whole sight and tried a bunch of so called fixes and still when i plug in my atrix 2 in boot mode (only it boot mode it does this) all i hear is instead of the dehdo that lets u know its connected i hear duhduhduh and RSD doesnt detect my device... im trying to fxz to 2.3.5 then ota upto ICS then root but i cant do any of these because of this please help.
Click to expand...
Click to collapse
First and foremost, this belongs in the q&a section. Is your phone an MB865, an ME865, is it AT&T branded? Have you tried uninstalling then reinstalling the Motorola drivers on your PC? Tried a different USB port and/or another PC? Can you give a little more information? Awesome sound effects, by the way.lol
Sent from this thing.

1BadWolf said:
First and foremost, this belongs in the q&a section. Is your phone an MB865, an ME865, is it AT&T branded? Have you tried uninstalling then reinstalling the Motorola drivers on your PC? Tried a different USB port and/or another PC? Can you give a little more information? Awesome sound effects, by the way.lol
Sent from this thing.
Click to expand...
Click to collapse
thank u lol but im sure u can imagnine the sound an...
AT&T
MB865
and i do believe i said ive tried nearly everything that is listed on this site well other sites to...
I dont need special files for my special model phone or the fact that its at&t but if that information helps u make it connect to my pc like it does when its not in fastboot then there ya go and btw to the Q/A section they can move it...

greatanomaly said:
thank u lol but im sure u can imagnine the sound an...
AT&T
MB865
and i do believe i said ive tried nearly everything that is listed on this site well other sites to...
I dont need special files for my special model phone or the fact that its at&t but if that information helps u make it connect to my pc like it does when its not in fastboot then there ya go and btw to the Q/A section they can move it...
Click to expand...
Click to collapse
Yeah, I was kidding. This site can be too serious at times. I know you said you tried everything, but a lot of people say that and it isn't always true, especially when they ask questions on the same day they became a member. I wasn't trying to offend you or insinuate anything. I asked if you had an AT&T branded phone because I was curious as to why you wanted to flash to 2.3.5 then ota to 2.3.6 then ota again to 4.0.4 instead of using this:
http://forum.xda-developers.com/showthread.php?t=1961310
to go straight to 4.0.4?
So your PC isn't detecting your phone, but ONLY when in fastboot mode, correct? Is the phone detecting the PC? By that I mean, on my phone when I boot into fastboot mode, at first it says:
AP Fastboot Flash Mode (S)
0A.72
Battery OK
OK to Program
Connect USB
Data Cable
Then when I connect it to the PC it changes to:
AP Fastboot Flash Mode (S)
0A.72
Battery OK
OK to Program
Transfer Mode:
USB Connected
Are you at least getting that?
Sent from this thing.

stuck on boot logo
1BadWolf said:
Yeah, I was kidding. This site can be too serious at times. I know you said you tried everything, but a lot of people say that and it isn't always true, especially when they ask questions on the same day they became a member. I wasn't trying to offend you or insinuate anything. I asked if you had an AT&T branded phone because I was curious as to why you wanted to flash to 2.3.5 then ota to 2.3.6 then ota again to 4.0.4 instead of using this:
http://forum.xda-developers.com/showthread.php?t=1961310
to go straight to 4.0.4?
So your PC isn't detecting your phone, but ONLY when in fastboot mode, correct? Is the phone detecting the PC? By that I mean, on my phone when I boot into fastboot mode, at first it says:
AP Fastboot Flash Mode (S)
0A.72
Battery OK
OK to Program
Connect USB
Data Cable
Then when I connect it to the PC it changes to:
AP Fastboot Flash Mode (S)
0A.72
Battery OK
OK to Program
Transfer Mode:
USB Connected
Are you at least getting that?
Sent from this thing.
Click to expand...
Click to collapse
no sir ny fone is not showing this
it still says
Connect Usb
data cable
i stuck while i was on jbleak 4.1.2 and through SD card i flashed CM 10.1
once it worked but now it stucked on the boot logo ... it appears and gone ... and then shows black screen.
even in recovery when i tried to reinstall same zip file of CM10.1 it failed on signature verification.
please help me sir help me..!!
:crying::crying::crying::crying::crying::crying::crying::crying::crying:

Gr8mobiPro said:
no sir ny fone is not showing this
it still says
Connect Usb
data cable
i stuck while i was on jbleak 4.1.2 and through SD card i flashed CM 10.1
once it worked but now it stucked on the boot logo ... it appears and gone ... and then shows black screen.
even in recovery when i tried to reinstall same zip file of CM10.1 it failed on signature verification.
please help me sir help me..!!
:crying::crying::crying::crying::crying::crying::crying::crying::crying:
Click to expand...
Click to collapse
Chill man..nothing to worry about..please install motorola drivers..it should work.

its still not working
nishant203 said:
Chill man..nothing to worry about..please install motorola drivers..it should work.
Click to expand...
Click to collapse
wot motorola driver ..?? i have installed moto device manager and it is not showing any thing connected.. because it remain in boot mode..:crying::crying::crying::crying::crying::crying::crying:

Use Virtual PC
I still have the same issue. I have installed Windows 7 on VM Ware workstation i.e virtual desktop and then followed the below steps :-
-Reboot your Virtual PC
-Install Motorola drivers.
-Reboot your computer
-Install RSD Lite
-Reboot your computer
-Boot your phone into Fastboot mode
-Connect your phone to your computer using a high-quality (preferably OEM) cable.
-Let your PC install any necessary drivers. When it finishes it should tell you that the device "Fastboot Edison S" is ready for use.
-Turn your phone off, disconnect the cable
-Reboot your computer
-Boot your phone back into Fastboot mode
-Wait a couple seconds then connect your phone to your computer
-Wait a couple more seconds, then look at the bottom text that's displayed on your phone. It should say
This means that your phone is connected to your computer.
-Open up RSD Lite
-Wait a couple seconds. At the top of the list should be your phone (under model it should say "Fastboot Edison S")
-If you've done all this and everything has worked out for you, flash the fxz! Make sure to follow the instructions in the noob thread as specifically as possible

Gr8mobiPro said:
wot motorola driver ..?? i have installed moto device manager and it is not showing any thing connected.. because it remain in boot mode..:crying::crying::crying::crying::crying::crying::crying:
Click to expand...
Click to collapse
This seems to be happening more lately. it IS a driver issue of some sort, that is for sure. I would just use one of the scripts, or moto-fastboot manually. they do the same thing as rsd but through command line either with your own typing, or a .bat script.
This may also work better in linux, so you can try downloading a live cd/usb of ubuntu and seeing if it is recognized. no need for drives with linux, just download one of the scripts that includes the moto-fastboot utility. Let me know if you need more help.

same issue
i am having the same issue with my at&t atrix 2. it is soft bricked due to an upgrade from gb to jbleak. ap fastboot flash mode (s) oa.65 battery ok ok to program connect usb data cable same message i have installed different motorola usb driver versions. i have also soldered the 4 pin to the 1 red+5v factory usb cable
https://www.google.com/url?q=http:/...ds-cse&usg=AFQjCNE6DkvEZi41YPAYKVPqH_AlA4f4cQ
but still my pc says unable to recognize usb device. i dnt what to do any more. im in mexico and purchasing a new phone is very expensive i need help is there something any one can do i am sure my device is not completely bricked i just cant get the mofokin pc to recognize the mofokin phone in fastboot

[ROM] Karbonn A12+ Stock Jelly Bean ROM flashable via SP flash Tool...

Hello guys..
Karbonn A12+ is newly launched Android phone with 1.3GHz processor and 512MB RAM...Still we didn't have Stock ROM for this model...
Now i proudly present Stock jellybean ROM for Karbonn A12+..
I prepared it to flash via SP Flash Tool..
Now don't worry to experiment with your Mobile do experiment and you can recover your karbonn A12+...
So keep learning and Do some intresting experiment and make some custom ROM...
NOTE:- Flashing Process and these type of development process may cause any unwanted and unknown errors...So please Try it at your OWN RISK...I will not Responsible for any damge...
now here are is method to flash.
(Try At Your OWN RISK...)
you Need.
1.An PC (Ofcorse you need and PC or laptop)
2. Karbonn A12+ Stock jellybean ROM (Download)
3. SP_Flash_Tool v3.1312.0.139 (other Version may not work proper)(NOTE:- Flashing Process and these type of development process may cause any unwanted and unknown errors...So please Try it at your OWN RISK...I will not Responsible for any damge...[/COLOR][/B]
Download Links:-
[url]http://a2zandroidrom.blogspot.in/2014/09/karbonn-a12-stock-jellybean-rom.html
Drivers are added...
links are
http://a2zandroidrom.blogspot.in/2014/09/karbonn-a12-stock-jellybean-rom.html
Download file is password protected..password is given in download link page...Download is available in small parts as well as in single part also...
post your review please !!

Good work Bro . . .

suthar88.sunil said:
Good work Bro . . .
Click to expand...
Click to collapse
Thanks

Phone not connecting
greatpapa said:
Hello guys..
Karbonn A12+ is newly launched Android phone with 1.3GHz processor and 512MB RAM...Still we didn't have Stock ROM for this model...
Now i proudly present Stock jellybean ROM for Karbonn A12+..
I prepared it to flash via SP Flash Tool..
Now don't worry to experiment with your Mobile do experiment and you can recover your karbonn A12+...
So keep learning and Do some intresting experiment and make some custom ROM...
NOTE:- Flashing Process and these type of development process may cause any unwanted and unknown errors...So please Try it at your OWN RISK...I will not Responsible for any damge...
now here are is method to flash.
(Try At Your OWN RISK...)
you Need.
1.An PC (Ofcorse you need and PC or laptop)
2. Karbonn A12+ Stock jellybean ROM
3. SP_Flash_Tool v3.1312.0.139 (other Version may not work proper)
Method
1. Download all files on your PC and extract them on one place.
2. now you will have two folder name by "!Files_to_FlashTool" and "SP_Flash_Tool_v3.1312.0.139"
3. Now RUN SP flash Tool.
4. now click on "scatter-loading" tab.
5. now Select "scatter file"....Sp tool will list up all the component to flash.
6.now hit the Download button on SP...you will see an warning something like user data and cache are not loaded or something...just ignore it...and click on "Yes".and now you are ready to flash.
7. Now switchoff your phone (If it is on) and pull out the battery.
8. Connect your phone while battery is out.
9.After connecting your Phone insert your battery...
10. Sp Tool will recognise your Phone and flashing will start.
11. Green circle will show that flash is Done...
Enjoy
NOTE:- Flashing Process and these type of development process may cause any unwanted and unknown errors...So please Try it at your OWN RISK...I will not Responsible for any damge...
Download file is password protected..password is given in download link page...Download is available in small parts as well as in single part also...
post your review please !!
Click to expand...
Click to collapse
My phone is not connecting. i tried many times. help me out plzzz..

Combination
vikphogat said:
My phone is not connecting. i tried many times. help me out plzzz..
Click to expand...
Click to collapse
First of all your have to install VCOM USB drivers for MTK6572 devices....
And then after hitting download button connect your phone while pressing both volume down + up button together....or try this type of different combination....
yes this is most difficult part..i tried 20 times myself....
if not working then try on different machine
As you will be connected there will be an Red and yellow line on SP tool
Next to try..
after hitting download button Press power and volume up button and then connect USB cable while pressing those key together....
Even you can try this new flash tool
http://www.mediafire.com/download/tnas2hjqruf2iht/SP_Flash_Tool_v5.1343.01_by_indiantitaniclover.zip

thanks dude..!!
greatpapa said:
First of all your have to install VCOM USB drivers for MTK6572 devices....
And then after hitting download button connect your phone while pressing both volume down + up button together....or try this type of different combination....
yes this is most difficult part..i tried 20 times myself....
if not working then try on different machine
As you will be connected there will be an Red and yellow line on SP tool
Next to try..
after hitting download button Press power and volume up button and then connect USB cable while pressing those key together....
Even you can try this new flash tool
Click to expand...
Click to collapse
i will try it surely.. can u please also provide me the link to vcom usb drivers for karbonn a12+ ?
thanks in advance.. :laugh::good:

Dri
vikphogat said:
i will try it surely.. can u please also provide me the link to vcom usb drivers for karbonn a12+ ?
thanks in advance.. :laugh::good:
Click to expand...
Click to collapse
New flashtool will recognise direct....Hope so...download new flash tool and try...

greatpapa said:
New flashtool will recognise direct....Hope so...download new flash tool and try...
Click to expand...
Click to collapse
i have tried it nearly 15 16 times. but when i put battery presing and holding volume up + down button phone goes to factory mode. 8 options written in chinese are showing up.

Powrer
vikphogat said:
i have tried it nearly 15 16 times. but when i put battery presing and holding volume up + down button phone goes to factory mode. 8 options written in chinese are showing up.
Click to expand...
Click to collapse
First click on download in flashtool...then press
power + volume up and connect while pressing...Working for me..tested by myself...

hard bricker karbonn a12+........
Great work and nice tutorial some how unbricked my phone 100% working
\\beginers dont post any spam without reading the complete tutorial as I did
thanks a lot for helping

not working
greatpapa said:
First click on download in flashtool...then press
power + volume up and connect while pressing...Working for me..tested by myself...
Click to expand...
Click to collapse
plz help it's not working.installed usb driver & latest sp flash tool.still not working ????

Fastboot
Lovesahota said:
plz help it's not working.installed usb driver & latest sp flash tool.still not working ????
Click to expand...
Click to collapse
Hello....
Try this one..
Switch off your mobile...
Now press volume up + Power button...
Then you will see three option something like Recovery, fastboot, factory...
You have to choose fastboot option...
when fastboot is selected then connect your phone to PC via USB cable...this will install some helpful drivers to your PC....and then again try the flash method without battery...

Stuck at the EYE boot screen of Karbonn A12+. Any help please? Yes, I followed the instructions carefully.
http://playrangers.com/KarbonnA12plus/
in that page the usb drivers of 6577 is provided. Kindly provice MT6572 VCOM drivers.

Process DOne ?
nightcrawler218 said:
Stuck at the EYE boot screen of Karbonn A12+. Any help please? Yes, I followed the instructions carefully.
http://playrangers.com/KarbonnA12plus/
in that page the usb drivers of 6577 is provided. Kindly provice MT6572 VCOM drivers.
Click to expand...
Click to collapse
Did you flashed in proper way ?
means your Sptool recognise your mobile and did you see red and yellow line in sptool and was process done or not ?

greatpapa said:
Did you flashed in proper way ?
means your Sptool recognise your mobile and did you see red and yellow line in sptool and was process done or not ?
Click to expand...
Click to collapse
yeah, everything was according to the tutorial. phone was detected, first red, then blue then yellow progress bar & finally green circle. I removed the usb & reinserted the battery after flashing then pressed the power button. Karbonn animation shown & stuck at the eye screen. After a number of failed attempts I decied to erase the whole device & then flash again. I erased flash+bootloader. The phone is dead now. not powering up. But if I connect the phone via usb to pc a beep sound is heard. Any clue, how to restore the bootloader?

How
nightcrawler218 said:
yeah, everything was according to the tutorial. phone was detected, first red, then blue then yellow progress bar & finally green circle. I removed the usb & reinserted the battery after flashing then pressed the power button. Karbonn animation shown & stuck at the eye screen. After a number of failed attempts I decied to erase the whole device & then flash again. I erased flash+bootloader. The phone is dead now. not powering up. But if I connect the phone via usb to pc a beep sound is heard. Any clue, how to restore the bootloader?
Click to expand...
Click to collapse
How did you erase the Bootloader....??
if you have deleted your bootloader then it would be diffecult to revive the phone

greatpapa said:
How did you erase the Bootloader....??
if you have deleted your bootloader then it would be diffecult to revive the phone
Click to expand...
Click to collapse
I Used SP flash tool to format the device. There was an option for erasing everything (Flash + bootloader).
Will the service center accept my case.?

Ummm
nightcrawler218 said:
I Used SP flash tool to format the device. There was an option for erasing everything (Flash + bootloader).
Will the service center accept my case.?
Click to expand...
Click to collapse
Try again whole method...if you are hearing an beep sound....
Does your mobile is going in recovery mode or fastboot mode ?
Power + volume up (battery is inserted)

greatpapa said:
Try again whole method...if you are hearing an beep sound....
Does your mobile is going in recovery mode or fastboot mode ?
Power + volume up (battery is inserted)
Click to expand...
Click to collapse
Thanks a million times man for your suggestion.
I tried with fastboot but no device shown. I went to device manager & uninstalled-then reinstalled the drivers. That actually helped me to build the serial communication between SP flash tool & Device.
Then I discarded the battery & retried the SP flash tool, this time the phone is finally detected & flashed successfully. red, blue, yellow bar then green circle. DONE.
Now, the same issue. Karbonn boot animation is displayed & stuck at the eye screen. I have covered the halfway but cant be able to get success in the other half (cant see the homescreen or anything.)
---------- Post added at 09:15 PM ---------- Previous post was at 09:07 PM ----------
Phone is OK now but it says INVALID IMEI... any suggestions please...

Good
nightcrawler218 said:
Thanks a million times man for your suggestion.
I tried with fastboot but no device shown. I went to device manager & uninstalled-then reinstalled the drivers. That actually helped me to build the serial communication between SP flash tool & Device.
Then I discarded the battery & retried the SP flash tool, this time the phone is finally detected & flashed successfully. red, blue, yellow bar then green circle. DONE.
Now, the same issue. Karbonn boot animation is displayed & stuck at the eye screen. I have covered the halfway but cant be able to get success in the other half (cant see the homescreen or anything.)
---------- Post added at 09:15 PM ---------- Previous post was at 09:07 PM ----------
Phone is OK now but it says INVALID IMEI... any suggestions please...
Click to expand...
Click to collapse
Don't worry....
Now your phone will be fine....As i will get time i will give you tutorial to write your IMEI number....Till then you can search and google it....your phone is ok...will recover it soon....

Blu Life One XL (2015 - Build KTU84P) Root And TWRP Recovery Auto-Install

Root & TWRP Recovery For The Life One XL
Those of you who have the Life One XL who have been looking to root it and install TWRP custom recovery now have an automated method to achieve root and install TWRP on this phone.
I have put together an auto-install script that will root your Life One XL and flash TWRP recovery onto it in Linux.
Requirements:
You must have both the ADB and FASTBOOT utilities on your computer and in your path.
You must have enabled USB DEBUGGING on your Life One XL phone.
Instructions:
Download this file --> Life One XL Auto-Root & TWRP Install For Linux
Open a terminal window on your Linux computer;
cd to the directory where you extracted the zip file;
Connect your Life One XL to your computer;
Type the command "./root-life-one-xl.sh" <ENTER> in the terminal window;
Sit back and follow the prompts.
Once you are finished, you will have a rooted Life One XL with the TWRP custom recovery installed on it. There are a few custom ROM's available for it -- none of which I have tried personally -- but you will be ready to install them if you choose. You can check the "Official Thread" for more information.
*** I WILL NOT BE RESPONSIBLE FOR BRICKED PHONES. THE USE OF THIS FILE IS AT YOUR OWN RISK. ***

I have the Blu Life One (not the XL). Will this work on that one? Also, do you a method for Windows pc's?

eyes2east said:
I have the Blu Life One (not the XL). Will this work on that one? Also, do you a method for Windows pc's?
Click to expand...
Click to collapse
Check your build number, and see if you have the MediaTek processor. This is designed for the Qualcomm based phone, with build number KTU84P.

I have this phone. it was already rooted and my daughter made the mistake of trying to do the over the air update. The phone has been stuck in android system recovery ever since (2 months).
I have located a repair suite, which appears to be from BLU. Unfortunately I can not get the phone into download mode, so I can't connect the computer to connect to the phone.
Here is a link to the zipped blu repair folder :
BLU X010Q

ahhhh. the sound of one hand clapping

So how do you get to download mode?

Deejaydark said:
So how do you get to download mode?
Click to expand...
Click to collapse
Haven't been able to figure it out

22350 said:
I have this phone. it was already rooted and my daughter made the mistake of trying to do the over the air update. The phone has been stuck in android system recovery ever since (2 months).
I have located a repair suite, which appears to be from BLU. Unfortunately I can not get the phone into download mode, so I can't connect the computer to connect to the phone.
Here is a link to the zipped blu repair folder :
BLU X010Q
Click to expand...
Click to collapse
Sorry can you fix the link? It's un error 429 thank

Emergency
Could you please upload your BLU life one xl debuggerd file mine has been corrupted and I need it. It isn't a big file and the path is /system/bin/debuggerd. Please help me

Thank you very much.
22350 said:
I have this phone. it was already rooted and my daughter made the mistake of trying to do the over the air update. The phone has been stuck in android system recovery ever since (2 months).
I have located a repair suite, which appears to be from BLU. Unfortunately I can not get the phone into download mode, so I can't connect the computer to connect to the phone.
Here is a link to the zipped blu repair folder :
Hi 22350.
You help me a lot with that file. I was able to recover my phone back from the recovery mode loop.
Just for the knowledge, the loop appears if someone has his phone rooted and apply the Blu company update.
I have to erase the link because i need to have at least 10 post to use external links. But you can find it in this place.
Again, thank you very much for this.
Click to expand...
Click to collapse

Can you please tell me how to flash rom to the phone

Kyle holder said:
Can you please tell me how to flash rom to the phone
Click to expand...
Click to collapse
Lol I have twrp and root and still till this day no one has made a backup of the stock rom that I need. Can someone please make a backup of there rom that I can use please. I tried the suite you provided and it reads my phone but fails in the process. Probably because I have no OS installed... that's why I need a stock rom and thank you for whoever cares

Thanks a lot...
22350 said:
I have this phone. it was already rooted and my daughter made the mistake of trying to do the over the air update. The phone has been stuck in android system recovery ever since (2 months).
I have located a repair suite, which appears to be from BLU. Unfortunately I can not get the phone into download mode, so I can't connect the computer to connect to the phone.
Here is a link to the zipped blu repair folder :
BLU X010Q
Click to expand...
Click to collapse
With the files you provide I can restore my cellphone... thanks a lot...
You must only with the cellphone power off... plug into the pc... remenber the drivers allready be installed... then the download button in the app for flashing its able to clic in...
this is the only way to enter in download mode...

So far some people use this and not one backup made? Wow what a community

when I click download it fails to switch to edf or something. How can I fix this?

22350 said:
I have this phone. it was already rooted and my daughter made the mistake of trying to do the over the air update. The phone has been stuck in android system recovery ever since (2 months).
I have located a repair suite, which appears to be from BLU. Unfortunately I can not get the phone into download mode, so I can't connect the computer to connect to the phone.
Here is a link to the zipped blu repair folder :
BLU X010Q
Click to expand...
Click to collapse
Do everything the instructions tell you to... Before you hit the "download" button... Simply power off the device... Leave it powered off connect USB... And hit download button WHEN IT BECOMES AVAILABLE ... Worked like a champ for me.

Deejaydark said:
So how do you get to download mode?
Click to expand...
Click to collapse
I've been able to get in DL mode by doing the following:
from the Black and white Boot Logo... hold the power +vol up key until it cycles... once it cycles switch to the power + Vol Down Key... Viola! DL Mode...
Not entirely true what stated in the above ...but if you play with it you'll realize Im close you only have to hold either or... To be noted... You can flash the phone from the diagnostic menu as well... Having the device powered off doesnt always work... Having it in diagnostic mode has worked 100% of the time.
I've been tinkering in my spare time... And have bricked this phone a time or dozen or two... But it's still kicking... And you can flash from lollipop back to kk...

Does someone have the backup of the stock rom ?

Casiuscr said:
Does someone have the backup of the stock rom ?
Click to expand...
Click to collapse
Thanks to user of XDA 22350 for provide these archives...
BLU Life One 2015 X010Q Stock ROM
This is the link... again... the old link provided by 22350 its broken...
---------- Post added at 05:12 PM ---------- Previous post was at 05:08 PM ----------
Obayne said:
I've been able to get in DL mode by doing the following:
from the Black and white Boot Logo... hold the power +vol up key until it cycles... once it cycles switch to the power + Vol Down Key... Viola! DL Mode...
Click to expand...
Click to collapse
The Download mode, its easy to enter... only with the app stay running and ready to upload the rom and drivers installed, you must power off the phone and connect it to the computer... when you connect the phone the computer says new device detected installing drivers... and then the button to start the recovery become enable to put the stock rom...

eyes2east said:
I have the Blu Life One (not the XL). Will this work on that one? Also, do you a method for Windows pc's?
Click to expand...
Click to collapse
This showed work perfectly with the Blu Life One.

[Guide] Unbrick Your UNLOCKED Lenovo P2a42

Hey Friends,
You must have seen very good days with Lenovo P2 but when there comes a bad day when your phone stops responding to button holds and restarts. You may or may not have a clue what to do to get your phone working again just like before.
I got into this situation where only thing my phone was able to operate was a RED LED on connecting it to my laptop. Then I had to read tens of pages on XDA to find answers to all my questions. If you are in such a situation and your phone is UNLOCKED then you have come to the right place. Procedure is quite simple but remember, I am writing this guide to define complete process from blackout to complete update so follow this guide as per your needs.
I faced this situation of Total Blackout / Dead Phone (Almost) with only Red LED working and it can be very scary. So, here is the simplest procedure you can follow. I want to appreciate all those people who helped me in finding a way to boot my phone with each and everything working. Long story short, let's get this done.
Tools Required:
I am mentioning here all the Tools you will need. I will urge you to download and save these tools in case you want to unbrick your phone any time:
1. Minimal ADB and Fastboot setup for PC
2. Lenovo USB drivers v1.1.33
3. Qualcomm USB Drivers
4. Qualcomm Flash Image Loader (QFIL) v2.0.1.9 for your PC in case you have corrupted your phone's IMEI and/ or Baseband
5. Blankflash.bat in case you want to recover from total blackout (Attached)
6. Stock MM S048 Firmware for Lenovo P2 in case phone doesn't boot
7. S048_ModemTelephony.zip in case your phone boots through Stock MM S048 but SIM isn't detected and IMEI is missing. I have made a complete modem zip file for installation through recovery.
8. S251_ModemTelephony.zip in case your phone is on latest firmware and doesn't detect SIM and has lost IMEI. I have made a complete modem zip file for installation through recovery.
9. QCN file for recovering baseband version and giving you most precious network signals. (Attached)
10. WinRAR or PeaZip for uncompressing files
I will recommend you to have a specific folder for keeping all these tools in a single place.
Procedure for Unbricking:
Before going with the procedure, make sure you have downloaded all the files you need, updated Lenovo and Qualcomm drivers etc. Here is the procedure:
1. If total blackout with red LED notification when connecting to PC: Unzip blankflash.zip to a folder in C drive. Now connect your P2 to PC through USB, press volume+, volume- and power button simultaneously and double click blankflash.bat. You might have no success in your first try. Just keep trying and it will load your phone to Fastboot. Restart your phone in TWRP if installed and install a working ROM for your phone after doing a wipe. If all is good and phone works OK then great but if you have lost IMEI and baseband then it is better to reinstate your phone through first MM stock ROM S048
2. Install S048 firmware through Minimal ADB and Fastboot - use flash instructions in .txt file.
3. Wait for startup of phone. Check if fingerprint, BT, WIFI and SIM work if all work then OK.
4. If fingerprint, BT, WIFI and SIM are not working then check IMEI through dialer. Dial *#06#. If IMEI is not available then install latest TWRP through Fastboot.
5. Start P2 in TWRP recovery and install S048_ModemTelephony.zip. Restart phone to see if WIFI and SIM work.
6. If SIM is detected but not giving signals and Baseband is shown as unknown then extract 000000_0.qcn file given in .7z and restore through QFIL and restart your phone into Fastboot.
7. Now, install stock recovery of S048 firmware through Fastboot and restart your phone.
8. Use your phone like you normally do and update your P2 till firmware S251 and see if everything works including calls. Update your phone through OTA.
9. After OTA installation, stock recovery may say that update failed. Just press Back, go into Wipe user data menu and Wipe Cache only. Restart your phone which will be updated to latest version and will ask you to update to a newer version. Allow it to download the next update.
10. After installation of S251 update, install latest TWRP through Fastboot and install most recent version of LOS 16 so that your vendor partition is stable and free from any bloated files. Now, use your phone just like you want to.
If you need further clarification then ask in this thread.

Bro my phone is not unlocked can i try thz one

Ranji007 said:
Bro my phone is not unlocked can i try thz one
Click to expand...
Click to collapse
You should download S048 and use flashall.bat inside that archive to install it all. However, if you lose IMEI or baseband then you can use modem and qcn files given in this thread.

alirazaagha said:
You should download S048 and use flashall.bat inside that archive to install it all. However, if you lose IMEI or baseband then you can use modem and qcn files given in this thread.
Click to expand...
Click to collapse
Bro now i wanna use ...minimal adb ..my phone is totally bricked only red light glowing

Ranji007 said:
Bro now i wanna use ...minimal adb ..my phone is totally bricked only red light glowing
Click to expand...
Click to collapse
don't worry just flash blank flash from the link given in the op, you will get the bootloader back

hackiee said:
don't worry just flash blank flash from the link given in the op, you will get the bootloader back
Click to expand...
Click to collapse
Bro how to connect my phone to blank flash...can u PLZZ help

hackiee said:
don't worry just flash blank flash from the link given in the op, you will get the bootloader back
Click to expand...
Click to collapse
Laptop is not detecting my device bro i installed all lenovo and Qualcomm drivers...any idea

Ranji007 said:
Laptop is not detecting my device bro i installed all lenovo and Qualcomm drivers...any idea
Click to expand...
Click to collapse
If red light blinks, your phone can be detected by your laptop. Check ports in device manager settings and you'll see a new port with Qualcomm 9800 series number. If that's there, try blankflash to start in fastboot. It might need some tries before startup. Be patient and keep trying till you are in fastboot.

alirazaagha said:
If red light blinks, your phone can be detected by your laptop. Check ports in device manager settings and you'll see a new port with Qualcomm 9800 series number. If that's there, try blankflash to start in fastboot. It might need some tries before startup. Be patient and keep trying till you are in fastboot.
Click to expand...
Click to collapse
Bro ..thanks for reply....in my phone red blink is glowing continuously ..but after connecting there is no change...can u say which buttons i want to press?

Ranji007 said:
Bro ..thanks for reply....in my phone red blink is glowing continuously ..but after connecting there is no change...can u say which buttons i want to press?
Click to expand...
Click to collapse
Press Volume+, Volume- and Power simultaneously and double click flashblank.bat. It might take some tries to finally install the scripts and start phone in fastboot. It took me 20+ tries to finally detect my phone through blankflash. Please, read OP completely.

alirazaagha said:
Press Volume+, Volume- and Power simultaneously and double click flashblank.bat. It might take some tries to finally install the scripts and start phone in fastboot. It took me 20+ tries to finally detect my phone through blankflash. Please, read OP completely.
Click to expand...
Click to collapse
Bro we want to connect each time removing usb cable and connect again like that ..we wanna do 20 times??

Ranji007 said:
Bro we want to connect each time removing usb cable and connect again like that ..we wanna do 20 times??
Click to expand...
Click to collapse
No. Keep USB connected. Try blankflash. If it doesn't detect phone or go ahead. Close command terminal, double click again and keep doing it till it processes the files. If it is stuck somewhere. Close terminal and try again.

alirazaagha said:
No. Keep USB connected. Try blankflash. If it doesn't detect phone or go ahead. Close command terminal, double click again and keep doing it till it processes the files. If it is stuck somewhere. Close terminal and try again.
Click to expand...
Click to collapse
Bro is there any solution ..i continuously pressed volume and power buttons connected to laptop and opening blank flash continuously for number of times ...but there was no reaction...only waiting for device is showing ? on my pc ...

Ranji007 said:
Bro is there any solution ..i continuously pressed volume and power buttons connected to laptop and opening blank flash continuously for number of times ...but there was no reaction...only waiting for device is showing ? on my pc ...
Click to expand...
Click to collapse
Check if your USB cable is alright and appropriate drivers are installed. Otherwise reinstall drivers, restart your PC and try again.

alirazaagha said:
Check if your USB cable is alright and appropriate drivers are installed. Otherwise reinstall drivers, restart your PC and try again.
Click to expand...
Click to collapse
Bro we want to change any settings in device manager ...?

Ranji007 said:
Bro we want to change any settings in device manager ...?
Click to expand...
Click to collapse
No. Just update drivers.

alirazaagha said:
No. Just update drivers.
Click to expand...
Click to collapse
Bro when u take to service center they said for u motherboard problem or something??

Ranji007 said:
Bro when u take to service center they said for u motherboard problem or something??
Click to expand...
Click to collapse
Fortunately, I never took it there.

alirazaagha said:
Fortunately, I never took it there.
Click to expand...
Click to collapse
My phone was fallen in water then i changed the display..few days after it stopped working ..and when i take to serive centre they said to change motherboard..but it's the 80% of phone price...so iam here ?..iam trying thiz method

Ranji007 said:
My phone was fallen in water then i changed the display..few days after it stopped working ..and when i take to serive centre they said to change motherboard..but it's the 80% of phone price...so iam here ..iam trying thiz method
Click to expand...
Click to collapse
I think you might have damaged some hardware. But anyway if you want to use blankflash, I have a method.
In lenovo p2 we have another mode called QDloader mode, in which we can use blankflash. For entering into this mode, it's little tricky but, can enter in one or two go.
So, here's how:
1. Switch off the mobile.
2. Press the volume up key,
3. While holding the volume up key, insert the usb cable and at the same time press the power button (this is the trick, we have to insert and hit at the same time).
And voila! :highfive: you will see black screen with only red notification led blinking.
we are into QDloader mode. Now use blankflash :good: