Hi All,
I just thought of painting the back of my sensation, just the panels with the antennas I have a spare so it's okay if something goes wrong. But I read somewhere that sandpapering these panels could mess with the antennas. But what about just covering it with a little spraypaint or something?
From what I understand, the antennas run through the plastic in the back cover (hence the contact points on the inside of the case). If you were to sand all the way through and into the metal antennas, that could have a performance drop - maybe. However, lightly sanding just enough to remove paint? Doubt it. Maybe I'll paint mine as well. I have both a black and a white and much prefer the white cover.
Same here, but I also thought about just painting over the white back cover, that wouldn't do any harm now would it?
There are threads that show the alloy panels sanded down and polished (look great by the way) and no performance drop there, so you should be able to do the same prep the surface down the the bare metal, prime and paint away
Post up your results it may encourage others to follow you
I'm sorry, but do you mean the big backpanel or the small panels with the antennas? Because I want to paint the panels with the antennas, I'm also considering sanding the big panel and maybe making it shiny!
I will certainly post results if I have them!!
sshede said:
From what I understand, the antennas run through the plastic in the back cover (hence the contact points on the inside of the case). If you were to sand all the way through and into the metal antennas, that could have a performance drop - maybe. However, lightly sanding just enough to remove paint? Doubt it. Maybe I'll paint mine as well. I have both a black and a white and much prefer the white cover.
Click to expand...
Click to collapse
How will you be painting it? Are you going to use spraypaint?
That's what I was thinking of.
Related
I just started developing this odd creaking noise near the bottom and sides of my S4G. Even with a Seidio Active case wrapped around it, the creaking can be felt and heard when hitting the bottom buttons.
The fix is pretty easy. You just need to decrease the amount of movement the back cover has.
I had some .010 mil fiber (fish) paper laying around so I cut a small square that covers the sim card and microsd card area. You can probably use something else, but hey, why not use some insulated paper if you have it.
Lay the paper on top of the area and then slowly place the back cover back on. No holes are in that area above the sim and microsd, so no worries there. You should see an immediate improvement
I needed more than that to stop the creaking/screen movement.
Pathetic we have to go to these lengths
jlevy73 said:
I needed more than that to stop the creaking/screen movement.
Pathetic we have to go to these lengths
Click to expand...
Click to collapse
What did you have to do?
I tried used two squares of paper, but that made the back bulge out a little too much to my liking.
GideonX said:
What did you have to do?
I tried used two squares of paper, but that made the back bulge out a little too much to my liking.
Click to expand...
Click to collapse
I took a post-it and folded it twice. Then placed it on the bottom right area and closed up the cover. For me when I press down on the bottom right side of the screen the whole screen sort of depresses a bit. Only way I could get rid of that was to place the paper in that region. Problem solved.
Post it would have been my backup method
Sent from my HTC Sensation 4G
buy another battery, i recently got an anker also had the creaking problems, noticed the anker is a TINY bit thicker than the stock battery and it removed that problem completely. and that anker battery was DIRT cheap
I just lined the case with some scotch tape. from the bottom to about 3/4 of the way up. I just went around the antenna nubs and the usb hole.
Posted this in another thread, but felt it was valuable here too...
Got the creaking here also, definitely a design flaw. Being obsessive with my devices i couldnt live with it!
I do not recommend putting paper in the cover to fill the gap, as this is just expanding the cover further making it even MORE loose when the paper is not in there. Also i wouldn't recommend it because the paper pushes the back cover out a little more, you may loose a connection for the ground. Which is the little metal springy thing, half way up the right hand side. Obviously its not a good idea to 'push' the cover further away from this ground spot. I have heard that people have had issues with screen responsiveness due to a static build up from not grounding properly.
What i did to fix this problem was a bit of a kitbash of sorts.
Mine was creaking on the bottom right area, like most. The problem is there is too much play between the little black catches on the battery cover and the latch on the handset. Instead of filling up the gap between the phone and the cover (Ala paper, card in the cover) I closed it!
What you need to do is get some very thin plastic film. Like that on kids toy packaging etc. Not the thicker stuff though. This stuff would be under 1mm thick. It came as a viewing window in the box my new wallet came in. So you can sorta imagine what im talking about.
I cut a piece about 10mm long and as wide as one of the two little black catches. I applied a VERY thin coat of super glue to one end of the film. Just enough to cover the area under the catch. Then i carefully placed the film with the superglue on it under the catch, and then quickly applied some pressure to it with some tweezers. Then i carefully cut the excess off with a pair of finely tipped nail scissors.
The result is that it now PULLS the screen/phone INTO the cover more by making the little black catch thicker. Not the opposite (paper method), which pushes the cover out, creating a further problem of adding more paper under the cover over time as the cover expands/loosens to compensate. Not to mention a possible grounding loss and resulting damage.
Hope this helps some people that have had multiple replacements or could not be bothered replacing for such a cosmetic issue. (Like me). It definitely works, just got to get your surgeon on and be accurate with your placement of the film.
Apply this to what ever side creaks the most, and bam its gone. Nice. Solid phone... again.
If anyone wants more specific details etc, im all ears.
Regards,
Matt.
will try it with an double side film ...
i mean a film that hold back cover and phone together ;-) i think doing paper in there will do damage with time
I contacted HTC and they sent me another/new one. No more creaking!
RaptorRVL said:
I contacted HTC and they sent me another/new one. No more creaking!
Click to expand...
Click to collapse
Back cover or whole phone?
I have the same problem too. And it just seems to get more and more "cracking"
Like most of us that keep no cover on our phone, my battery plate was all scratched to heck. I saw the other "mirror polish" mod and it looked great, but also looked like a lot of work and would get scratched again. I bought a can of rubberized spray (see pic) and wound up with a great result (see pic.) The only color Home Depot had was black, and I think a gray might have looked better, but I still like the results and the phone is less slippery now than with the metal cover. This took 3 coats (30 minutes drying time between coats) then I let it dry for 18 hours before using it. Turned out pretty good, but long-term results are TBD...
I like did u just spray the back part? Any trouble with fitting it afterwards as it must add a layer of bulk?
Desire Z Glite 2.0.1
Shambolicuk said:
I like did u just spray the back part? Any trouble with fitting it afterwards as it must add a layer of bulk?
Desire Z Glite 2.0.1
Click to expand...
Click to collapse
It added less bulk than I thought it would, it's really not much at all and it fits just fine afterwards. Actually, before, it would slide like a little when locked in place (just enough to notice - probably like .1 mm or so.) Now it is snug and has no jiggle at all.
I forgot to mention the hard part (prepping it...) Removing the original clear plastic coating was the hardest part - a combination of a dremel with the little wire wheel tool and my fingernail took about an hour, then I just hit it with some 220 grit sandpaper and cleaned it with mineral spirits.
I use the same stuff on my car (mid level 2009 Lancer but use the Plasti-dip to black out the front to make it look like an Evo [car guys will understand =p]) Very durable though I have not used it on my DZ yet. You beat me to the punch! I want to do the HTC part in red and the rest in black, will post when I have the time to do it.
Looks sharp though, contrast is nice
Doh! After only 1 day, I caught something on the curved edge and it started lifting the plastic coating... not very durable for this use - I might try again later though and see if I can come up with a better method.
Sent from my HTC Vision using XDA App
I like it! A little bit rougher texture, but you might try Duplicolor spray on bedliner.
I thought about taking my phone apart and using some white plastidip to change it white...
Durability is alright...on thinkpad forums, a couple of people mixed it with some black enamel paint which made it much more durable.
mralexsays said:
It added less bulk than I thought it would, it's really not much at all and it fits just fine afterwards. Actually, before, it would slide like a little when locked in place (just enough to notice - probably like .1 mm or so.) Now it is snug and has no jiggle at all.
Click to expand...
Click to collapse
I thought I was the only one who noticed the battery door wiggle room! No one ever mentions it. I really hope you find some way of preventing it from peeling. I'm practically drooling over those pictures you took. It looks extremely professional compared to most mods I've seen. You could easily set up a service where people send you their doors, some cash, and a self address envelope if you wanted to make some extra bucks.
kierren said:
I thought I was the only one who noticed the battery door wiggle room! No one ever mentions it. I really hope you find some way of preventing it from peeling. I'm practically drooling over those pictures you took. It looks extremely professional compared to most mods I've seen. You could easily set up a service where people send you their doors, some cash, and a self address envelope if you wanted to make some extra bucks.
Click to expand...
Click to collapse
I've been meaning to update this. I tried again - this time I sanded with 220 grit, used a "self-etching primer" on the cover, then the rubberized paint. This time it lasted 3 days before starting to peel off... I'm also able to scratch off the primer with my fingernails, so the primer didn't really help. I'm not sure what else to try to make this coating stick at this point.
mralexsays said:
I've been meaning to update this. I tried again - this time I sanded with 220 grit, used a "self-etching primer" on the cover, then the rubberized paint. This time it lasted 3 days before starting to peel off... I'm also able to scratch off the primer with my fingernails, so the primer didn't really help. I'm not sure what else to try to make this coating stick at this point.
Click to expand...
Click to collapse
I suggest powdercoating the back cover.
primeral said:
I suggest powdercoating the back cover.
Click to expand...
Click to collapse
Powder coating would be nice, but I don't have the equipment for that (and don't want to invest in it just for this.) Also, this cover has plastic tabs that I'd be worried about melting or detaching from the battery cover during the curing process.
As with basically all my other cellphones I convinced myself that I would not drop my Desire S on the road or other killer surfaces, so now that this has happened like 3 times at least, I am left with a few pretty nasty scratches on the aluminium body at the back. Besides dents and scratches not looking all too nice on their own, in this phone's case it looks even worse because it reveals the silver aluminium colour under the paint.
So does anybody know of a way to somehow kinda cover up these aluminium rends ?
meteish said:
As with basically all my other cellphones I convinced myself that I would not drop my Desire S on the road or other killer surfaces, so now that this has happened like 3 times at least, I am left with a few pretty nasty scratches on the aluminium body at the back. Besides dents and scratches not looking all too nice on their own, in this phone's case it looks even worse because it reveals the silver aluminium colour under the paint.
So does anybody know of a way to somehow kinda cover up these aluminium rends ?
Click to expand...
Click to collapse
put in a case, hide it in your pocket or go for the other extreme and scratch all the remaining paint off!
black edding. it works
TatoValverde said:
black edding. it works
Click to expand...
Click to collapse
Do you mean the Edding paint marker?
I have a grey Desire S which I dropped on a tile floor (ouch), left side first. Now it has two 1mm white dots where the metal paint chipped off, so I was looking for a silver permanent marker to maybe cover the white dots.
Have you tried the Edding marker? Does it wear off by taking the phone in and out of the pocket all the time?
If you've used this marker I'm looking forward to your feedback.
Thanks!
I have some lovely scratches and dents on mine. Somehow managed to take off a 1cm patch on the back under the logo; it's not too pretty. Even one of the dents is painful to touch as it is so sharp.
I'm afraid permanent marker will only make worse the current situation of my handset! In the case it goes and stays until it's needed!
Just put it in a case and convince yourself it never happened
Inginerul said:
Do you mean the Edding paint marker?
I have a grey Desire S which I dropped on a tile floor (ouch), left side first. Now it has two 1mm white dots where the metal paint chipped off, so I was looking for a silver permanent marker to maybe cover the white dots.
Have you tried the Edding marker? Does it wear off by taking the phone in and out of the pocket all the time?
If you've used this marker I'm looking forward to your feedback.
Thanks!
Click to expand...
Click to collapse
Sorry, I have a Black Desire S, and yeah, Edding marker works. Just try to find the smallest you can, since the marker on top of the original paint will be noticeable under sunlight. try to stick to the white dots, and good luck!
lol whats the chances of finding this thread, i've always kept mine in a rubber case to try an prevent chips etc, but i removed it the other day to flash another rom and noticed the dust/dirt that had got into the case had made a right mess on the back, so i htought what could i do to fix it,, i chose to just put it back in the case an forget about it but im defo gonna try the black paint pen,, thanks man
meteish said:
As with basically all my other cellphones I convinced myself that I would not drop my Desire S on the road or other killer surfaces, so now that this has happened like 3 times at least, I am left with a few pretty nasty scratches on the aluminium body at the back. Besides dents and scratches not looking all too nice on their own, in this phone's case it looks even worse because it reveals the silver aluminium colour under the paint.
So does anybody know of a way to somehow kinda cover up these aluminium rends ?
Click to expand...
Click to collapse
Perhaps an oil based enamel paint... you may be able to get a small tin from a hobby shop.
Metal paint
Guys, please allow me to brag about how I fixed the two tiny paint chips on my Desire S. :laugh:
As suggested by TatoValverde, at first I wanted to buy a paint marker, but since I have the gray Desire S this became a bit complicated. It turns out paint markers are not really easy to find (in Romania at least), much less if they're silver/gray and it becomes almost impossible to find a gray paint marker with a 0,8 mm tip.
After searching for 2 weeks I gave up the paint marker idea, went to the closest DIY store and bought a 750ml paint can + one thin brush. DIY stores are great because you can find a lot of colors and different shades. And by the way, a paint can costs about as much as a thin paint marker.
Although I tried to pick the closest shade of gray, even the smallest paint dot is noticeable on the phone so I had to put just a tiny amount, let it dry for some minutes, then very gently wipe off some of the excess paint. Then apply again a tiny bit of paint and wipe the whole area, over and over again until I couldn't really notice with the naked eye where the initial chips were.
The good thing is this paint seems to be pretty durable (as I've noticed when trying to clean some stains.. ) and it's water and UV resistant.
It's my first post so I would like to say hi to everyone,
I would like to replace the chrome bezel from my device. It's all scratched and it doesn't look good. I know that some people are just removing the "chrome" paint and sand it but in my case plastic underneath is light gray so it won't look good in my opinion.
I've read that screen is glued to the bezel and it's not so easy to do it that's why it would be great if someone could write step-by-step tutorial how to do it or to share his experience. Is it possible to do it at home without damaging the device?
i am also looking to change the bezel. From what i have found out so far the home button and the touch buttons (menu and back) are attached to the bezel. Also those buttons are glued to the screen and the screen itself glued to the bezel and the housing underneath it. So it should be very difficult and risky to try to change it. Most people in these forums agree that it is impossible to remove the screen without breaking it.
I can't really believe it is impossible to do it, and all who reported on it have tried to replace broken screens so maybe they were not careful enough. On the other hand no one has claimed to successfully removing the screen without damaging it.
Better be safe and hide the ugliness behind a case or something
So i decided to sand the chrome away in mine first to see if can get it look good and thus avoiding the hussle of opening the case
here are some photos of my work so far. Now i need to polish it
It looks really good with your white backplate... but I prefair to keep my phone black
How did you remove the chrome.. Sand it away? i tried scratching it off but it too risky in some places
Sent from my GT-I9001 using xda app-developers app
i used a nail file to sand the chrome away. I covered the edges of the screen with some tape to prevent scratches and also had a screen protector on just in case.
Just jam the tape in the gap between the bezel and he screen, you 'll be fine.
Also patience is highly advised
It looks prety good.
where did you get the white backplate from
http://www.ebay.co.uk/itm/WHITE-BAT...K_Replacement_Parts_Tools&hash=item3cc4149074
how much to pay?
It look very nice with white bezel.nice work!
my s plus was white to begin with,i didn't change that.
actually the bezel is grey and not white, it doesn't look all that great up close but it's still better than the damaged chrome.
i mean to paint it glossy white to match the backplate as much as possible but i am still looking for the right paint.
i will come back and upload more photos when done
Sent from my GT-I9001
It's very nice
How about paiting the border black after you sand it down? I'm thinking of doing this with some spray paint.
keeekeeess said:
How about paiting the border black after you sand it down? I'm thinking of doing this with some spray paint.
Click to expand...
Click to collapse
Give us news : did it work, how is that ?
My chrome has wore off as well. i have a case that covers the either side of the phone but would love to know if they could be replaced safely.
tomsi191 said:
So i decided to sand the chrome away in mine first to see if can get it look good and thus avoiding the hussle of opening the case
here are some photos of my work so far. Now i need to polish it
Click to expand...
Click to collapse
Thank you for this post. It gave me the confidence to try this on my back SGS.
On the corners of the bezel, the paint had chipped off making the phone look ugly. So I used my nails and blunt side of the blade to chip away the paint.
I found out that there are 2 layers of paint on top of the bezel. First is the black glossy paint which actually chips off.. Underneath that is the silver shade. This cannot be chipped off. You have to use your nails to make it go away. But later I figured out aftershave liquid just does fine and easy job. So maybe alcohol or nail polish remover would also work.
Since I used my nails and blunt blade, there are no signs of roughness or scratches on the surface except for 1 or 2 which is barely visible. So thankfully no need of polishing. The device looks much better now. :thumbup:
If you have figured out about the painting the bezel, let us know. Thanks!
Sent from my GT-I9000 using Tapatalk
Hello,
After changing the screen of my moto G, the new one is no longer stuck and is moving.... I had to remove the original glue (tape?) with an hair dryer.
My question is : with what I then paste the screen?
thanks a lot
Phil77560 said:
Hello,
After changing the screen of my moto G, the new one is no longer stuck and is moving.... I had to remove the original glue (tape?) with an hair dryer.
My question is : with what I then paste the screen?
thanks a lot
Click to expand...
Click to collapse
This is a very annoying problem of the chinese displays that come with a frame or pre-applied tape.
The display+lcd assembly is too heavy to be held by any normal 2-sided tape (3M 300LSE for example).
After hours of checking how the original thing was made it turned out that it has a rubber-like gasket that is glued to the frame, which acts as bonding surface for the 2nd glue used to hold the digitizer to the frame.
These are all my own findings, sadly no pne is discussing this problem anywhere or at least I didn't find any.
I've used a transparent epoxy (65-70% resin ~30-35% oxidizer so the compound hardens slower).Use a wooden tooth pick to apply the glue on the frame, don't put to much of it, just a hair-thin line.
Put the screen on and press it well and be ready to clean off any glue that may come out of the edges. The epoxy is easy to clean until it's set, use isopropyl alcohol 99% or some dry contact cleaner with a cotton cloth or kitchen paper.
The drawback of using epoxy is once it's set, you won't be able to remove the screen from the frame by any viable means.This is not a problem tho, since you can buy the whole assembly, should you need to replace the screen again.
Good luck.
:good:
Thanks a lot for your tip.
I'm gonna look for epoxy and try to do as well as you
Thank a lot once more
same issue
Hi,
Thank you very much for having shared your experience with us .
I have exactly the same issue with my Moto G and I've finally found a way out thanks to you. I would try this but I'm afraid of doing it bad. Should I apply the glue exactly in the border of the display? Do you happen to have any video showing it in detail?
Have a nice day
birikif said:
Hi,
Thank you very much for having shared your experience with us .
I have exactly the same issue with my Moto G and I've finally found a way out thanks to you. I would try this but I'm afraid of doing it bad. Should I apply the glue exactly in the border of the display? Do you happen to have any video showing it in detail?
Have a nice day
Click to expand...
Click to collapse
Hello,
You should apply the glue in the frame, as close as possible to the outer rim and spread it as much as possible on the thin inner lining where the plastic of the frame and the glass make contact.
You can also use universal transparent glue, like JIP or Henkel... etc.These glues are a bit more liquidish and it takes more time to set properly, but they are also more flexible and you can also remove the display with heat, should you have the need to .
Sorry no videos available on this, but with a little effort and reading you'll be fine.
liveroy's advice is great. I've followed it with success, although the screen I bought has the dreaded phantom touch issue (cheap ebay job!) and will have to go back (this issue was apparent even before I glued it to the mid-frame).
Firstly I separated the screen from the mid-frame with two small suction cups, designed for removing halogen light bulbs, on the top and bottom of the glass. This worked well, but I had to use very gentle tugs to ensure I didn't tear the ribbon cable. Because the double-sided tape used was already separating, this was quite an easy part of the job.
I used Araldite 2-Tubes Standard Epoxy, because it has a very long cure time, which allowed me to work slowly. With the screen and mid-frame completely separate and cleaned up, I then threaded the screen's ribbon cable through the hole before glueing. The trickiest bit was putting the epoxy along the frame where the ribbon cable is; to do this I just wedged some folded paper between frame and screen while I layed down the epoxy. I guess I could have just done this bit first and avoided the need for a paper wedge (this was used to prevent prematurely sticking the screen to the frame before all the epoxy's down).
I used the screen's plastic film to protect the screen from the epoxy, and cleaned the excess epoxy with an old bottle of disk head cleaner I found lying about (smelt very alcoholly!) and cotton buds. I used some clothes pegs to clamp the screen to the frame, but I took them off after a few hours. Then I left it for a couple of days. The result was as good as I could have hoped for. I can see a little bit of the dried epoxy in the very narrow trenches between the mid-frame and glass, but this doesn't bother me. Way better than having light streaming through the sides, and it seems like a really solid grip! When in use and getting warm I could still see a bit of lift at the sides, but because it was glued there was absolutely no gap.
Going back to the original need for this fix -
On my phone I believe this is due to a warped, concave logic board, effectively peeling the glass away from the mid-frame when fitted. If it were totally flat then I doubt this would happen. I guess the aftermarket screen manufacturers didn't factor this in when they decided to use "weak" double-sided tape. I've also noticed that, with the new screen in place, the outer back shell of the phone, that you put on last, doesn't quite fit at the bottom like with the old screen - there is now a small a gap where the inner plastic housing is exposed. I think this is because the new mid-frame is straighter than the old, and the old shell has itself bent over time.
Hi,
I'm happy to found this thread. It's the second screen i replace on my Motorola Moto G4 Plus because of this; you can view my comment here : https://www.witrigs.com/oem-lcd-screen-assembly-for-motorola-moto-g4-plus-black#customer-reviews
I will try to use super glue on the top of my screen, hope it'll work. EDIT 20190122 : it worked (be careful to not add too much glue like i did : it was covering camera when pressing !)
Thanks