[Q] P3100 only booting to Stock Recovery & not CWM? - Galaxy Tab 2 Q&A, Help & Troubleshooting

Unlocking GT-P3100 Bootloader - Help Needed
Hi All,
I was able to load the CWM recovery image through ODIN, below is the trace of the image download through ODIN:
=================================
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> recovery.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/021> Odin v.3 engine (ID:21)..
<ID:0/021> File analysis..
<ID:0/021> SetupConnection..
<ID:0/021> Initialzation..
<ID:0/021> Get PIT for mapping..
<ID:0/021> Firmware update start..
<ID:0/021> recovery.img
<ID:0/021> NAND Write Start!!
<ID:0/021> RQT_CLOSE !!
<ID:0/021> RES OK !!
<ID:0/021> Completed..
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/021> Removed!!
===============================
However, when I go to recovery menu , I'm not seeing CWM menu & only seeing "Android System Recovery (3e)".
A friend of mine suggested my boot loader needs to be unlocked.
Reading google it seems when we switch to download mode & connect to USB on PC, using ADB command "fastboot oem unlock" it should be done.
But the command is < Waiting for a device > , I can see "adb devices" reporting valid entries when in download mode.
Any suggestions....how to get CWM working ?
My Build # IML74K.P3100DDALE1
ICS 4.0.3
Want to get it rooted to install Chainfire3D to play some games with this Tablet.
Please help!

I was just messing around with wrong recovery image....
Grab this one http://imnuts.net/JxMIGa ( 9.4MB ) used ODIN 1.85 works 100%
My Flash count is now 5.
Got CWM Recovery installed OK & SuperUser app is now showing as well.
Time to install Chainfire3D on this GT-P3100 & enjoy some quality gaming
Confirmed 100% working.

How did you root it
Sent from my GT-P3100 using Tapatalk 2

Related

[S5301][GUIDE]how to root the Galaxy Pocket Plus S5301

Hi Evryone.
Until somebody will release CWM Recovery or any root method for the galaxy pocket plus, I managed to create a pre-rooted firmware.
This firmware base on the last build for S5301, is a full firmware exactly like the original, except the root.
after flash you will see the SuperSU app in the app drawer.
flashing this firmware do not doing wipe data. you will not lose anything.
also, this flash not increase your download binary count.
This file will work on any firmware/baseband/csc. you can always flash it like a stock firmware.
base on - XXAMC1.
PDA - S5301XXAMC1
PHONE- S5301XXMC1
CSC- S5301SERAMB1
Android version: 4.04
Download
https://mega.co.nz/#!qQ8B2BxZ!fhAggBRAzvsPzYejncA_Zlbkf-9r6UhPGU1BBYlbHqw
Installation instructions
install samsung usb drivers from here.
Download the 7z file above and extract it (with winrar or 7z) to some folder, you should receive a tar.md5 file.
Open odin 3 (attached in the zip)
Put the tar.md5 file in pda.
Put the device in download mode. (vol down + home + power button, and then click on vol up)
Connect your phone to usb and wait for odin detect the device.
Click start.
Enjoy
If you want to thank me for this work, you can do this by donating.. :good:
thank you very much
I'll try it but does it has Arabic language ??
I don't remember, but i think it does.
Don't work to me, apear modem error and stop odim
Here Odim check
<ID:0/012> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> S5301XXAMC1_S5301SERAMB1_S5301XXMC1_HOME_ROOTED.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/012> Odin v.3 engine (ID:12)..
<ID:0/012> File analysis..
<ID:0/012> SetupConnection..
<ID:0/012> Initialzation..
<ID:0/012> Get PIT for mapping..
<ID:0/012> Firmware update start..
<ID:0/012> BcmCP.img.md5
<ID:0/012> NAND Write Start!!
<ID:0/012>
<ID:0/012> Complete(Write) operation failed.
<ID:0/012> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
dragaoheremita said:
Here Odim check
<ID:0/012> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> S5301XXAMC1_S5301SERAMB1_S5301XXMC1_HOME_ROOTED.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/012> Odin v.3 engine (ID:12)..
<ID:0/012> File analysis..
<ID:0/012> SetupConnection..
<ID:0/012> Initialzation..
<ID:0/012> Get PIT for mapping..
<ID:0/012> Firmware update start..
<ID:0/012> BcmCP.img.md5
<ID:0/012> NAND Write Start!!
<ID:0/012>
<ID:0/012> Complete(Write) operation failed.
<ID:0/012> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Confirm that Kies is not running.
panda00 said:
Confirm that Kies is not running.
Click to expand...
Click to collapse
Kies is ok, im put back my phone with odin 3.07, and recovery.
Can anyone help me pls?
Is there any custom rom or if i root the phone can i disable that fuction?
http://forum.xda-developers.com/showthread.php?p=44391342#post44391342http://forum.xda-developers.com/showpost.php?p=44391342&postcount=1
avicohh said:
Hi Evryone.
Until somebody will release CWM Recovery or any root method for the galaxy pocket plus, I managed to create a pre-rooted firmware.
This firmware base on the last build for S5301, is a full firmware exactly like the original, except the root.
after flash you will see the SuperSU app in the app drawer.
flashing this firmware do not doing wipe data. you will not lose anything.
also, this flash not increase your download binary count.
This file will work on any firmware/baseband/csc. you can always flash it like a stock firmware.
base on - XXAMC1.
PDA - S5301XXAMC1
PHONE- S5301XXMC1
CSC- S5301SERAMB1
Android version: 4.04
Download
https://mega.co.nz/#!qQ8B2BxZ!fhAggBRAzvsPzYejncA_Zlbkf-9r6UhPGU1BBYlbHqw
Installation instructions
install samsung usb drivers from here.
Download the 7z file above and extract it (with winrar or 7z) to some folder, you should receive a tar.md5 file.
Open odin 3 (attached in the zip)
Put the tar.md5 file in pda.
Put the device in download mode. (vol down + home + power button, and then click on vol up)
Connect your phone to usb and wait for odin detect the device.
Click start.
Enjoy
If you want to thank me for this work, you can do this by donating.. :good:
Click to expand...
Click to collapse
Dear @avicohh
Can i return back to my stock rom? If yes then how???
reply plzzzz
Yes.
Just flash stock rom.
Sent from my Nexus 5 using Tapatalk

Recover from soft brick

Hello everybudy here is a guide to recover from soft brick(I ave only tested it on S7500 not other)
So do it at ur own risk
First download odin3 v1.85
Download stock firmware for ur cont
Extract both in a particular folder
Open odin
Go to Download mode in ur phone and press volume up
Connect ur phone to pc
If odin shows a yellow mark then u are ready to proceed
Mark PDA & and selct file
Click start in odin
Keep patience
After process is over odin will show pass
Now ur phone will reboot
(DO NOT REMOVE USB CABLE TILL ITS REBOOTED PROPELY)
Complete the setup
Now again switch off mobile as as the process has not been completed yet
Go to recovery mode (this time it would be stock recovery not cwm)
In recovery mode select wipe data factory reset and wipe cache partition
Reboot.
Now u are done!!
HIT THANKS IF I HELPED
Odin-http:// www.androidlegend.com/dl/Odin3_v1.85.zip
Stock firmware(pda)- http://www.tsar3000.com/Joomla/inde...ace-plus-firmwares&catid=55:samsung&Itemid=82
Sent from my GT-S7500
whats new in this there is a sticky in which hole process is shown correctly
and 1 thing -
you should edit PDA ...it is different for different countries
you provided the firmware which is not for Indian users
http://www.sammobile.com/firmwares/
this is were you can get firmware for your own country !!
Ok i have edited pda and u can check the link
Also, I am a Indian and have tried this and its almost same
Only we have to change the language
Thanks any way
Sent from my GT-S7500
I had searched but it was not in q n ans. So i put it in this section. I dont know about stickies as i am new to this
Sent from my GT-S7500
There has also a type of soft brick where you will not be able to access download mode. Then odin will not work
then use USB jig. See http://www.xda-developers.com/android/need-a-samsung-usb-jig-build-your-own/
Ya i know
Sent from my GT-S7500
[email protected] said:
Ya i know
Sent from my GT-S7500
Click to expand...
Click to collapse
I know that you know. It was not mentioned so I mentioned it.
Itz showing fail please help asap!!!!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> S7500DDMF2_S7500ODDMF1_S7500DDME1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> system.img.ext4
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
i tried its coming failed,i tried downloading odin and firmware again from sam mobile, evn removed kies still the same please help asap!!
Ashmit Poojari said:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> S7500DDMF2_S7500ODDMF1_S7500DDME1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> system.img.ext4
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
i tried its coming failed,i tried downloading odin and firmware again from sam mobile, evn removed kies still the same please help asap!!
Click to expand...
Click to collapse
Keep Odin open and change USB ports, remount the PDA & flash. Hope this helped, worked for me

[q] help required for bricked samsung gt-s6102

My friend has a Samsung GT-S6102 and he tried to flash a custom firmware without pre-rooting the phone. The phone was stuck in bootloop and he gave the phone to me for repair because I have been flashing phones like my Xperia mini pro and Samsung Monte, etc.
However, this is the first time I had to use Odin to do something like this. As per my experience so far, the most difficult part is to find the right firmware for this phone (I require the Indian firmware). So, after lots of brainstorming in the XDA forum I flashed these files (a) BOOT_S5360DDKK1_REV05.tar (b) torino_1205.pit (c) PDA, Phone and CSC files from S6102_DDMC1_ODDMB1_DDMC1. Now after successfully completing the flash process the phone still goes to bootloop and the Samsung Galaxy logo appears upside down (mirror image). I am attaching the screenshot here for your reference. Moreover, I cannot view the download mode because of white screen when I press volume down+home+power keys. But I can still reflash following the steps as it would if it was normal.
Here's the odin flash log.
<ID:0/008> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> PDA_S6102_DDMC1.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> MODEM_S6102_DDMC1.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CSC_S6102_ODDMB1.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/008> Odin v.3 engine (ID:8)..
<ID:0/008> File analysis..
<ID:0/008> SetupConnection..
<ID:0/008> Initialzation..
<ID:0/008> Set PIT file..
<ID:0/008> DO NOT TURN OFF TARGET!!
<ID:0/008> Get PIT for mapping..
<ID:0/008> Firmware update start..
<ID:0/008> BcmBoot.img
<ID:0/008> NAND Write Start!!
<ID:0/008> boot.img
<ID:0/008> param.lfs
<ID:0/008> system.img
<ID:0/008> userdata.img
<ID:0/008> BcmCP.img
<ID:0/008> Transmission Complete..
<ID:0/008> Now Writing.. Please wait about 2 minutes
<ID:0/008> Receive Response from boot-loader
<ID:0/008> csc.rfs
<ID:0/008> RQT_CLOSE !!
<ID:0/008> RES OK !!
<ID:0/008> Removed!!
<ID:0/008> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
Any help would be greatly appreciated. Please note that this phone is not rooted so can't go to CWM either.
So, frustrating... somebody got to have a way to revive this bricked phone.
Can somebody tell me how to root and to flash a custom kernel on an already bricked phone.....?
From the screenshot it shows that the odin version is not correct (Its for galaxy grand)
Try using Odin 3v1.8
For firmwares
Go here
Sent by typing by my fingers
@AMIT
Thank you very much for your reply Amit but I'm afraid that it's not going to work either. I've also used the older version of odin the one that you mentioned but with no luck. My only chances are if I can somehow alter the root permission and flash a custom kernel and then flash a new rom. However, I've searched many forums but nobody knows anything about rooting an already bricked phone.
It's quite easy otherwise to root a phone that's in a working condition. So sad...
Anyways, thanks a lot buddy....
Withe Screen on GT-S6102
Hello people
I'need a little help
I was trying to apply a monster rom to my girlfriend galaxy y duos.
Then it reboot and I could see the Monster boot animation but with the picture all mess up.
Then I enter in to Recovery mode an the menu was also mess up.
finaly I could enter with the odin 3 an flash the CSC_S5360_ODDLK1 pack (3 files)
then After reboot all I have is a with screen.
I can go in recovery menu or download menu, at least that I see, because all I see is a the withe screen
Can somebody help to riveve this brick
Thanks

Gt-n8000 stuck on samsung 10.1 screen

Try flash via odin show fail..ALREADY VIEW ALOT YOURTUBE AND XDA..NOT FIX.. PRESS POWER + VOL BUTTON CAN'T ENTER RECOVER MODE. OR EMMC CHIP SPOIL? THANK
Pls help.
One use the report button and ask a mod to move the post to the correct section .Q&A
Try flash via odin show fail
What fail .
What are you flashing ??
JJEgan said:
One use the report button and ask a mod to move the post to the correct section .Q&A
Try flash via odin show fail
What fail .
What are you flashing ??
Click to expand...
Click to collapse
Because keep stuck on samsung logo. Can't go into recovery mode too. Suspect firmware corrupt. Fail show at 1st pic there Sboot.bin. So try re-flash stock rom, one of my htc problem like this after flash phone work as normal.
Some say this due to EMMC chip issue.
Pls help.
Try flashing a full firmware .
Full as in a single file
JJEgan said:
Try flashing a full firmware .
Full as in a single file
Click to expand...
Click to collapse
All already try. The pic 'FAIL" red color show in odin is single file(full firmware).
This case similar like my other HTC keep reboot in logo, htc after flash work as normal.
Alot of people facing same issue too, search around forum still unable to fix. Probably emmc.
Usual for Emmc fail is Odin fails at Nand write.
Sent from my SM-N930F using XDA-Developers Legacy app
JJEgan said:
Usual for Emmc fail is Odin fails at Nand write.
Sent from my SM-N930F using XDA- Legacy app
Click to expand...
Click to collapse
This note already problem quite some time, before that show the error below, at NAND Write start, so is EMMC problem, need replace the chip?
Also the battery charging bar not running, previously when charge will show the battery bar running.
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N8000XXUDPB1_N8000LUXDPB1_N8000XXUDNH1_HOME.tar.md 5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> sboot.bin
<ID:0/006> NAND Write Start!!
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
This note already problem quite some time, before that show the error below, at NAND Write start, so is EMMC problem, need replace the chip?
Probably but ask a service centre .
Enter in download mode and try to flash any recovery cwm, twrp or philz with odin. See if now you're able to boot into recovery mode.
Enviado do meu GT-I9301I através de Tapatalk
skyx1128 said:
Try flash via odin show fail..ALREADY VIEW ALOT YOURTUBE AND XDA..NOT FIX.. PRESS POWER + VOL BUTTON CAN'T ENTER RECOVER MODE. OR EMMC CHIP SPOIL? THANK
Pls help.
Click to expand...
Click to collapse
I have the same problem but mine shows a error at system.img.
View attachment 5290635
And When I power it through the adaptor it shows the charging symbol and then it turns off. (As shown in the above image).
This happen when it ran out of charge for a day since then its been stuck with this logo. (As shown above).
Wrong firmware sys.img.
Wrong size PIT file .
JJEgan said:
Wrong firmware sys.img.
Wrong size PIT file .
Click to expand...
Click to collapse
I appreciate your help but I am new to all this and if you can explain things in detail would be helpful.
I have worked on xiaomi phones before but they use adb & fastboot to flash things, so I am a beginner for the flashing of samsung devices.
I downloaded the files from samobile and one more from other source and they are for the correct model as well.
This log is of the file download from the other source and was a single file.
Odin Log:
<ID:0/009> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/009> Odin engine v(ID:3.1401)..
<ID:0/009> File analysis..
<ID:0/009> Total Binary size: 1764 M
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Get PIT for mapping..
<ID:0/009> Firmware update start..
<ID:0/009> NAND Write Start!!
<ID:0/009> SingleDownload.
<ID:0/009> system.img
<ID:0/009> FAIL!
<ID:0/009>
<ID:0/009> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/009> Removed!!
This log is of the file download from samobile with four different files.
Odin Log:
<ID:0/009> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/009> Odin engine v(ID:3.1401)..
<ID:0/009> File analysis..
<ID:0/009> Total Binary size: 1765 M
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Set PIT file..
<ID:0/009> DO NOT TURN OFF TARGET!!
<ID:0/009>
<ID:0/009> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
In a post similar to this, someone mentioned that device stuck on logo could be due to a corrupted kernel.
Firmware is tied to the 16 or 32 Gb memory , check yours first.
JJEgan said:
Firmware is tied to the 16 or 32 Gb memory , check yours first.
Click to expand...
Click to collapse
Mine is the 16GB model and the firmware is also correct.
Probable
Flash stock but still custom rom
Hi folks , I installed cyanogenmod rom to my Samsung Galaxy Note 10.1 (GT-N8005) a year ago. It stuck on boot animation. Then I flash stock rom via odin , it passed. But still stuck on cyanogenmod boot animation. Can anyone help ? How can I...
forum.xda-developers.com
JJEgan said:
Probable
Flash stock but still custom rom
Hi folks , I installed cyanogenmod rom to my Samsung Galaxy Note 10.1 (GT-N8005) a year ago. It stuck on boot animation. Then I flash stock rom via odin , it passed. But still stuck on cyanogenmod boot animation. Can anyone help ? How can I...
forum.xda-developers.com
Click to expand...
Click to collapse
Thanks for the help but I already checked this link and many others but the conclusion was when the error occurs at "NAND write" step then the emmc chip was probably damaged but mine stops at a different step. And also if I replace the emmc wouldn't I lose the data?
[RECOVERY][OFFICIAL] TWRP 3.6.0_9 [N8000 N8010 N8020]
Team Win Recovery Project 3.x, or twrp3 for short, is a custom recovery built with ease of use and customization in mind. Its a fully touch driven user interface no more volume rocker or power buttons to mash. The GUI is also fully XML driven and...
forum.xda-developers.com
try flashing this twrp recovery, note use odin 3.10.5, note disable auto reboot, in options, after sucess reboot recovery, click flash, and see how big the internal storage is. If no sucess flashing twrp recovery or internal storage = 0MB your emmc is fried, else you device still has life.
If your device still has life install this custom android(LineageOS is just the UI name, it is stable android)(follow the steps)(ask @html6405 for questions, I can only help you to here)
LineageOS 16.0 Android 9 for GT-N8000 GT-N8010 GT-N8013 GT-N8020 FINAL VERSION EOL
/* * Your warranty is now void. * * I am not responsible for bricked devices, dead SD cards, * thermonuclear war, or you getting fired because the alarm app failed. Please * do some research if you have any concerns about features included in...
forum.xda-developers.com

G355HN flash problems with odin

Hello everyone,
My old phone starting to do some weird things: on power on, it doesn't respond. If I put it in charge, it reboots continuosly, by vibrating and showing the Samsung logo for a fraction of second. I don't know why.
I'm able to put it in download mode, but if I try to flash a stock rom, odin doesn't works.
I downloaded this rom from sammobile: G355HNXXU0AQA1_G355HNITV0AQA1_G355HNXXU0AQA1_HOME Italy Android 4.4.2
Putted into Odin 3.13 in the section AP, I tried to flash but the message was "There is no PIT Partition". Options enabled: "AutoReboot, F.ResetTime".
Second attempt: Options enabled: "AutoReboot, F.ResetTime and Re - Partition", same firmware. Result: operation failed.
Third attempt: changed the cable and the firmware, with: G355HNXXS0APH1_G355HNITV0APF1_G355HNXXU0APE1_HOME
It doesn't works. My log is:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1301)..
<ID:0/005> File analysis..
<ID:0/005> Total Binary size: 1105 M
<ID:0/005> SetupConnection..
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
No pit file used during the procedure, only the firmware as AP.
Any help?
Thanks in advance
UP! Please, nobody?
Same problem
My odin do the same!!! Please help

Categories

Resources