My friend has a Samsung GT-S6102 and he tried to flash a custom firmware without pre-rooting the phone. The phone was stuck in bootloop and he gave the phone to me for repair because I have been flashing phones like my Xperia mini pro and Samsung Monte, etc.
However, this is the first time I had to use Odin to do something like this. As per my experience so far, the most difficult part is to find the right firmware for this phone (I require the Indian firmware). So, after lots of brainstorming in the XDA forum I flashed these files (a) BOOT_S5360DDKK1_REV05.tar (b) torino_1205.pit (c) PDA, Phone and CSC files from S6102_DDMC1_ODDMB1_DDMC1. Now after successfully completing the flash process the phone still goes to bootloop and the Samsung Galaxy logo appears upside down (mirror image). I am attaching the screenshot here for your reference. Moreover, I cannot view the download mode because of white screen when I press volume down+home+power keys. But I can still reflash following the steps as it would if it was normal.
Here's the odin flash log.
<ID:0/008> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> PDA_S6102_DDMC1.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> MODEM_S6102_DDMC1.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CSC_S6102_ODDMB1.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/008> Odin v.3 engine (ID:8)..
<ID:0/008> File analysis..
<ID:0/008> SetupConnection..
<ID:0/008> Initialzation..
<ID:0/008> Set PIT file..
<ID:0/008> DO NOT TURN OFF TARGET!!
<ID:0/008> Get PIT for mapping..
<ID:0/008> Firmware update start..
<ID:0/008> BcmBoot.img
<ID:0/008> NAND Write Start!!
<ID:0/008> boot.img
<ID:0/008> param.lfs
<ID:0/008> system.img
<ID:0/008> userdata.img
<ID:0/008> BcmCP.img
<ID:0/008> Transmission Complete..
<ID:0/008> Now Writing.. Please wait about 2 minutes
<ID:0/008> Receive Response from boot-loader
<ID:0/008> csc.rfs
<ID:0/008> RQT_CLOSE !!
<ID:0/008> RES OK !!
<ID:0/008> Removed!!
<ID:0/008> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
Any help would be greatly appreciated. Please note that this phone is not rooted so can't go to CWM either.
So, frustrating... somebody got to have a way to revive this bricked phone.
Can somebody tell me how to root and to flash a custom kernel on an already bricked phone.....?
From the screenshot it shows that the odin version is not correct (Its for galaxy grand)
Try using Odin 3v1.8
For firmwares
Go here
Sent by typing by my fingers
@AMIT
Thank you very much for your reply Amit but I'm afraid that it's not going to work either. I've also used the older version of odin the one that you mentioned but with no luck. My only chances are if I can somehow alter the root permission and flash a custom kernel and then flash a new rom. However, I've searched many forums but nobody knows anything about rooting an already bricked phone.
It's quite easy otherwise to root a phone that's in a working condition. So sad...
Anyways, thanks a lot buddy....
Withe Screen on GT-S6102
Hello people
I'need a little help
I was trying to apply a monster rom to my girlfriend galaxy y duos.
Then it reboot and I could see the Monster boot animation but with the picture all mess up.
Then I enter in to Recovery mode an the menu was also mess up.
finaly I could enter with the odin 3 an flash the CSC_S5360_ODDLK1 pack (3 files)
then After reboot all I have is a with screen.
I can go in recovery menu or download menu, at least that I see, because all I see is a the withe screen
Can somebody help to riveve this brick
Thanks
I have a stock Galaxy note 10.1 NT8010, i hadnt used it in a few days. Went to power on and wouldnt boot. Thinking it was dead i charged it for a few hours and still wouldnt turn on. The power brick is fine, i bought a new stock cable, just waiting for that to come and rule out the cable. But its stock android no rooting or anything.
Any ideas?
Battery shows as charging ??
Odin mode ??? or Recovery Mode ???
JJEgan said:
Battery shows as charging ??
Odin mode ??? or Recovery Mode ???
Click to expand...
Click to collapse
Thanks for replying. Screen is completely dead not even a backlight.
For odin to work would i have to have it rooted previously?
For odin to work would i have to have it rooted previously?
No it does not require root .
JJEgan said:
For odin to work would i have to have it rooted previously?
No it does not require root .
Click to expand...
Click to collapse
Ok, so the pc is not picking it up at all.
I took off the back cover, disconnected the battery and reconnected.
Plugged it into the charger while the cover was still off. On the top left its making a "ti-ti-ti" noise while plugged into power.
Im guessing the motherboard/battery/screen are/is dead. Well one of the 3.
Any ideas?
amsung Tab GT-N8010 Rom doesn't Install, PIT issue, Flashing Screen, do not turn ON
I have Samsung Tab GT-N8010
When I try to turn on, its screen flashing White for half second and then Black and Continuosly till the Battery End.
I try to Install ROM 4.4.2 with ODIN 3.10.7 and get this error
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1100)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004>
<ID:0/004> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
I tried different PIT files including 3 different N8010.pit and 8013.pit and 8020.pit
but the issue remaining same
I read all the google search including Russian websites at-least but I couldn't find the issue
I have original cable
EMMC Corrupted may be
I need Solution plz help if anyone can
rehansonu said:
amsung Tab GT-N8010 Rom doesn't Install, PIT issue, Flashing Screen, do not turn ON
I have Samsung Tab GT-N8010
When I try to turn on, its screen flashing White for half second and then Black and Continuosly till the Battery End.
I try to Install ROM 4.4.2 with ODIN 3.10.7 and get this error
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1100)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004>
<ID:0/004> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
I tried different PIT files including 3 different N8010.pit and 8013.pit and 8020.pit
but the issue remaining same
I read all the google search including Russian websites at-least but I couldn't find the issue
I have original cable
EMMC Corrupted may be
I need Solution plz help if anyone can
Click to expand...
Click to collapse
same problem here! need help!!!!!
rehansonu said:
amsung Tab GT-N8010 Rom doesn't Install, PIT issue, Flashing Screen, do not turn ON
I have Samsung Tab GT-N8010
When I try to turn on, its screen flashing White for half second and then Black and Continuosly till the Battery End.
I try to Install ROM 4.4.2 with ODIN 3.10.7 and get this error
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1100)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004>
<ID:0/004> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
I tried different PIT files including 3 different N8010.pit and 8013.pit and 8020.pit
but the issue remaining same
I read all the google search including Russian websites at-least but I couldn't find the issue
I have original cable
EMMC Corrupted may be
I need Solution plz help if anyone can
Click to expand...
Click to collapse
Same problem here!!!! Service center says Motherboard replacement!!! Please help.
I have Samsung Tab GT-N8010
When I try to turn on, its screen flashing White for half second and then Black and Continuosly till the Battery End.
I try to Install ROM 4.4.2 & 4.1 also with ODIN 3.10.7 and get this error
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1100)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004>
<ID:0/004> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
I tried different PIT files including 3 different N8010.pit and 8013.pit and 8020.pit
but the issue remaining same
I read all the google search including Russian websites at-least but I couldn't find the issue
I have original cable
(Internal Partition Corrupted I think (EMMC Error))
I am waiting for useful solution. Anyone can help me here?
rehansonu said:
I am waiting for useful solution. Anyone can help me here?
Click to expand...
Click to collapse
same problem here, have you fix it?
rehansonu said:
I am waiting for useful solution. Anyone can help me here?
Click to expand...
Click to collapse
Have you odin the firmware and apply the pit at the same time?, Plus you shouldn't use pits for other models (ie 8013,8020)
How much storage do you have?
Hi all, my S4 mini won't turn on, while i was messaging, the display shutting down and can't turn on it.
When i connected it to my pc, my pc found new driver: QHSUSB_DLOAD. I searched it on google and i discovered that my phone was bricked without doing anything. So i flashed a sdcard with debrick.img and my phone finally showed:
Code:
BOOT RECOVERY MODE
CHECK BOOT PARTITIONS. .
BOOT RECOVERY
WRITE 139008 sectors
ddi : mmc_read failed
ODIN MODE
PRODUCT NAME: GT-i9195
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Custom
KNOX KERNEL LOCK: 0x0
KNOX WARRANT VOID: 0x0
CSB-CONFIG-LSB: 0x30
BOOTLOADER RP SWREV: 2
WRITE PROTECTION: Enable
So i tried to flash it with Odin and after Odin said:
Code:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BOOTLOADER_I9195XXUBML4_2340422_REV01_user_low_shi p_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CODE_I9195XXUBML4_2340422_REV01_user_low_ship_MULT I_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CSC_OXA_I9195OXABML4_2340422_REV01_user_low_ship_M ULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005>
<ID:0/005> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
So i searched on internet PIT files and i found "CSB_signed_SERRANOLTE_ONEPIT_OPEN_130523.pit", i tried to flash with it and Odin show same thing:
Code:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> recovery.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004>
<ID:0/004> There is no PIT partition.
While on the phone showed:
Code:
PIT FAIL : TOTAL SECTORS 0
ODIN flash read failure
I tried nand flash erase and show me other errors.
I think emmc died, if not, can anyone help me?
if emmc died, how can i install all partition ( bootloader ecc.) on sdcard for start the phone with it?
supergatto said:
Hi all, my S4 mini won't turn on, while i was messaging, the display shutting down and can't turn on it.
When i connected it to my pc, my pc found new driver: QHSUSB_DLOAD. I searched it on google and i discovered that my phone was bricked without doing anything. So i flashed a sdcard with debrick.img and my phone finally showed:
Code:
BOOT RECOVERY MODE
CHECK BOOT PARTITIONS. .
BOOT RECOVERY
WRITE 139008 sectors
ddi : mmc_read failed
ODIN MODE
PRODUCT NAME: GT-i9195
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Custom
KNOX KERNEL LOCK: 0x0
KNOX WARRANT VOID: 0x0
CSB-CONFIG-LSB: 0x30
BOOTLOADER RP SWREV: 2
WRITE PROTECTION: Enable
So i tried to flash it with Odin and after Odin said:
Code:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BOOTLOADER_I9195XXUBML4_2340422_REV01_user_low_shi p_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CODE_I9195XXUBML4_2340422_REV01_user_low_ship_MULT I_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CSC_OXA_I9195OXABML4_2340422_REV01_user_low_ship_M ULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005>
<ID:0/005> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
So i searched on internet PIT files and i found "CSB_signed_SERRANOLTE_ONEPIT_OPEN_130523.pit", i tried to flash with it and Odin show same thing:
Code:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> recovery.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004>
<ID:0/004> There is no PIT partition.
While on the phone showed:
Code:
PIT FAIL : TOTAL SECTORS 0
ODIN flash read failure
I tried nand flash erase and show me other errors.
I think emmc died, if not, can anyone help me?
if emmc died, how can i install all partition ( bootloader ecc.) on sdcard for start the phone with it?
Click to expand...
Click to collapse
here same
Can anyone help me?
@supergatto @espaciox99
I had the same problem with my galaxy s4 (gt-9505) where it didn't want to flash stock rom but I was able to root the phone (with cf autoroot) and also able to flash cwm recovery and flash resurrection remix and it's working fine now. Try it out and tell me if it works (better custom than nothing) and don't forget to press the thanks button .
a. felon said:
@supergatto @espaciox99
I had the same problem with my galaxy s4 (gt-9505) where it didn't want to flash stock rom but I was able to root the phone (with cf autoroot) and also able to flash cwm recovery and flash resurrection remix and it's working fine now. Try it out and tell me if it works (better custom than nothing) and don't forget to press the thanks button .
Click to expand...
Click to collapse
I tried CF-Auto-Root by this http://download.chainfire.eu/425/CF...Auto-Root-serranolte-serranoltexx-gti9195.zip
It says to use PIT file, i tried with it, and show same error of first post.
supergatto said:
I tried CF-Auto-Root by this http://download.chainfire.eu/425/CF...Auto-Root-serranolte-serranoltexx-gti9195.zip
It says to use PIT file, i tried with it, and show same error of first post.
Click to expand...
Click to collapse
Try with this method, it worked for me http://forum.xda-developers.com/showthread.php?t=2364980 good luck.
Don't just say thanks, press the ? button.
a. felon said:
Try with this method, it worked for me http://forum.xda-developers.com/showthread.php?t=2364980 good luck.
Don't just say thanks, press the button.
Click to expand...
Click to collapse
Here the result...
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
supergatto said:
Here the result...
Click to expand...
Click to collapse
This is the only thing I could find, hope it solves your problem bro.
Follow radicspeter's method as it's the one that seems to work. http://forum.xda-developers.com/showthread.php?t=2469375&page=2 Tell us if it works because @espaciox99 has the same problem like you, good luck.
Thanks for reply.
Code:
<ID:0/013> Odin engine v(ID:3.1100)..
<ID:0/013> File analysis..
<ID:0/013> SetupConnection..
<ID:0/013> Initialzation..
<ID:0/013> Get PIT for mapping..
<ID:0/013>
<ID:0/013> There is no PIT partition.
After used PIT file.
Code:
<ID:0/013> Odin engine v(ID:3.1100)..
<ID:0/013> File analysis..
<ID:0/013> SetupConnection..
<ID:0/013> Initialzation..
<ID:0/013> Set PIT file..
<ID:0/013> DO NOT TURN OFF TARGET!!
<ID:0/013> FAIL!
<ID:0/013>
<ID:0/013> Re-Partition operation failed.
UP
UP
UP
Your eMMC is definitively bricked, or at least it seems to be.
I didn't find any solution for that on quick, but you could be able to manually repartition your sd card. I see your device is booting from sd card, so maybe you could give a try to plug in the SD into a linux machine and see what it shows you.
xdvs23 said:
Your eMMC is definitively bricked, or at least it seems to be.
I didn't find any solution for that on quick, but you could be able to manually repartition your sd card. I see your device is booting from sd card, so maybe you could give a try to plug in the SD into a linux machine and see what it shows you.
Click to expand...
Click to collapse
I did it, and show 24 partitions like modem, sbl1, sbl2, sbl3, recovery, system, tz, hidden, cache, efs, and others, but if i want boot android with sdcard on my phone, how can i do?
I tried to copy eMMC from another S4 mini GT-I9195 on sdcard with "busybox dd..." command and it show same thing of pics.
Other thing that i tried on my phone with Odin: I tried to repartition eMMC with PIT and CSC and both show same thing of pics.
supergatto said:
I did it, and show 24 partitions like modem, sbl1, sbl2, sbl3, recovery, system, tz, hidden, cache, efs, and others, but if i want boot android with sdcard on my phone, how can i do?
I tried to copy eMMC from another S4 mini GT-I9195 on sdcard with "busybox dd..." command and it show same thing of pics.
Other thing that i tried on my phone with Odin: I tried to repartition eMMC with PIT and CSC and both show same thing of pics.
Click to expand...
Click to collapse
Good, I don't know if you need to install a bootloader but there are couple of videos showing how you can boot from sdcard by modifying the hardware.
xdvs23 said:
Good, I don't know if you need to install a bootloader but there are couple of videos showing how you can boot from sdcard by modifying the hardware.
Click to expand...
Click to collapse
Can you post some video? I didn't find it...
supergatto said:
Can you post some video? I didn't find it...
Click to expand...
Click to collapse
I found this on quick.
xdvs23 said:
I found this on quick.
Click to expand...
Click to collapse
In the video show same thing that i did... Except disassembling the phone. And this doesn't work.
supergatto said:
In the video show same thing that i did... Except disassembling the phone. And this doesn't work.
Click to expand...
Click to collapse
Ok so I don't know if there is any way to fix that. I also had a eMMC brick but on a S3 mini. If you did not install custom software you can send it for repair to samsung. If your warranty is already void you can pay for them to repair it but that would be expensive. You can also look for a eMMC replacement and replace it yourself. That could cost around 40 bucks, depending on what you need to order (dollars or euros).
Your emmc is now write-protected that means you simply can not flash anything. A reason for the brick can be overwriting the same file many times, using poorly developed apps or software / ROMs, daily backups in messaging apps, but also flashing many many many times could potentially make the eMMC to die. That is well-known on Samsung devices.
Is there any way for boot android from sdcard without replacing eMMC?
I found other thread with write protection: enabled but they can flash..
http://forum.xda-developers.com/showthread.php?t=2322185
Hello everyone,
My old phone starting to do some weird things: on power on, it doesn't respond. If I put it in charge, it reboots continuosly, by vibrating and showing the Samsung logo for a fraction of second. I don't know why.
I'm able to put it in download mode, but if I try to flash a stock rom, odin doesn't works.
I downloaded this rom from sammobile: G355HNXXU0AQA1_G355HNITV0AQA1_G355HNXXU0AQA1_HOME Italy Android 4.4.2
Putted into Odin 3.13 in the section AP, I tried to flash but the message was "There is no PIT Partition". Options enabled: "AutoReboot, F.ResetTime".
Second attempt: Options enabled: "AutoReboot, F.ResetTime and Re - Partition", same firmware. Result: operation failed.
Third attempt: changed the cable and the firmware, with: G355HNXXS0APH1_G355HNITV0APF1_G355HNXXU0APE1_HOME
It doesn't works. My log is:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1301)..
<ID:0/005> File analysis..
<ID:0/005> Total Binary size: 1105 M
<ID:0/005> SetupConnection..
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
No pit file used during the procedure, only the firmware as AP.
Any help?
Thanks in advance
UP! Please, nobody?
Same problem
My odin do the same!!! Please help