[S5301][GUIDE]how to root the Galaxy Pocket Plus S5301 - Miscellaneous Android Development

Hi Evryone.
Until somebody will release CWM Recovery or any root method for the galaxy pocket plus, I managed to create a pre-rooted firmware.
This firmware base on the last build for S5301, is a full firmware exactly like the original, except the root.
after flash you will see the SuperSU app in the app drawer.
flashing this firmware do not doing wipe data. you will not lose anything.
also, this flash not increase your download binary count.
This file will work on any firmware/baseband/csc. you can always flash it like a stock firmware.
base on - XXAMC1.
PDA - S5301XXAMC1
PHONE- S5301XXMC1
CSC- S5301SERAMB1
Android version: 4.04
Download
https://mega.co.nz/#!qQ8B2BxZ!fhAggBRAzvsPzYejncA_Zlbkf-9r6UhPGU1BBYlbHqw
Installation instructions
install samsung usb drivers from here.
Download the 7z file above and extract it (with winrar or 7z) to some folder, you should receive a tar.md5 file.
Open odin 3 (attached in the zip)
Put the tar.md5 file in pda.
Put the device in download mode. (vol down + home + power button, and then click on vol up)
Connect your phone to usb and wait for odin detect the device.
Click start.
Enjoy
If you want to thank me for this work, you can do this by donating.. :good:

thank you very much
I'll try it but does it has Arabic language ??

I don't remember, but i think it does.

Don't work to me, apear modem error and stop odim
Here Odim check
<ID:0/012> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> S5301XXAMC1_S5301SERAMB1_S5301XXMC1_HOME_ROOTED.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/012> Odin v.3 engine (ID:12)..
<ID:0/012> File analysis..
<ID:0/012> SetupConnection..
<ID:0/012> Initialzation..
<ID:0/012> Get PIT for mapping..
<ID:0/012> Firmware update start..
<ID:0/012> BcmCP.img.md5
<ID:0/012> NAND Write Start!!
<ID:0/012>
<ID:0/012> Complete(Write) operation failed.
<ID:0/012> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)

dragaoheremita said:
Here Odim check
<ID:0/012> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> S5301XXAMC1_S5301SERAMB1_S5301XXMC1_HOME_ROOTED.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/012> Odin v.3 engine (ID:12)..
<ID:0/012> File analysis..
<ID:0/012> SetupConnection..
<ID:0/012> Initialzation..
<ID:0/012> Get PIT for mapping..
<ID:0/012> Firmware update start..
<ID:0/012> BcmCP.img.md5
<ID:0/012> NAND Write Start!!
<ID:0/012>
<ID:0/012> Complete(Write) operation failed.
<ID:0/012> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Confirm that Kies is not running.

panda00 said:
Confirm that Kies is not running.
Click to expand...
Click to collapse
Kies is ok, im put back my phone with odin 3.07, and recovery.

Can anyone help me pls?
Is there any custom rom or if i root the phone can i disable that fuction?
http://forum.xda-developers.com/showthread.php?p=44391342#post44391342http://forum.xda-developers.com/showpost.php?p=44391342&postcount=1

avicohh said:
Hi Evryone.
Until somebody will release CWM Recovery or any root method for the galaxy pocket plus, I managed to create a pre-rooted firmware.
This firmware base on the last build for S5301, is a full firmware exactly like the original, except the root.
after flash you will see the SuperSU app in the app drawer.
flashing this firmware do not doing wipe data. you will not lose anything.
also, this flash not increase your download binary count.
This file will work on any firmware/baseband/csc. you can always flash it like a stock firmware.
base on - XXAMC1.
PDA - S5301XXAMC1
PHONE- S5301XXMC1
CSC- S5301SERAMB1
Android version: 4.04
Download
https://mega.co.nz/#!qQ8B2BxZ!fhAggBRAzvsPzYejncA_Zlbkf-9r6UhPGU1BBYlbHqw
Installation instructions
install samsung usb drivers from here.
Download the 7z file above and extract it (with winrar or 7z) to some folder, you should receive a tar.md5 file.
Open odin 3 (attached in the zip)
Put the tar.md5 file in pda.
Put the device in download mode. (vol down + home + power button, and then click on vol up)
Connect your phone to usb and wait for odin detect the device.
Click start.
Enjoy
If you want to thank me for this work, you can do this by donating.. :good:
Click to expand...
Click to collapse
Dear @avicohh
Can i return back to my stock rom? If yes then how???
reply plzzzz

Yes.
Just flash stock rom.
Sent from my Nexus 5 using Tapatalk

Related

[Stock][ROM][Odin] Galaxy Y Pro GT-B5510 firmware packages

Flashable Firmware Packages for the Galaxy Y Pro GT-B5510 Enjoy !
Temporary if your phone is bricked: http://lmgtfy.com/?q=GT-B5510+Odin+firmware+download
you can find the firmware on google!
I will update this thread as soon as possible
GT-B5510 Odin firmware download
Tutorial:
1. Start ODIN
2. Turn of your phone so that to go to Download Mode. The download mode can be entered by pressing Volume down Key + OK button, and holding both simultaneously press the Power Button.
2. Choose PDA and select the downloaded File (SS_DL.dll not needed 'delete it')
3. Leave everything as it is and click 'Start'
4. On your phone follow instructions after flashing is complete
Odin download: Odin
Press thanks if it helped you Thanks in advance
fail!
Hi!
Thanks for the os!
I tried the tutorial above a couple of times but odin gets the following error:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> B5510XXKJ2_B5510OXAKJ2_B5510XXKJ2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> sbl.bin
<ID:0/004> NAND Write Start!!
<ID:0/004> BcmCP.img
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I have a galaxy y pro gt-b5510.
android version 2.3.6
basehand version b5510xxkj2
kernel version [email protected] #16
build number gingerbread.xxkj2
i've entered in download mode, the display confirmed with:
odin mode
product name: gt-b5510
custom bin down: no(0 counts)
current bin: samsung official
Downloading...
do not turn off target!!
any suggestions?
thanks!
who pass?
djbasspower said:
Hi!
Thanks for the os!
I tried the tutorial above a couple of times but odin gets the following error:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> B5510XXKJ2_B5510OXAKJ2_B5510XXKJ2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> sbl.bin
<ID:0/004> NAND Write Start!!
<ID:0/004> BcmCP.img
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I have a galaxy y pro gt-b5510.
android version 2.3.6
basehand version b5510xxkj2
kernel version [email protected] #16
build number gingerbread.xxkj2
i've entered in download mode, the display confirmed with:
odin mode
product name: gt-b5510
custom bin down: no(0 counts)
current bin: samsung official
Downloading...
do not turn off target!!
any suggestions?
thanks!
Click to expand...
Click to collapse
That's weird I got those form sammobile maybe that's the problem I think you need to use this tool in order to work: http://forum.xda-developers.com/showthread.php?t=1611225 I am sorry I tought these package were working but if no one passes then I need to remove this thread.
But anyway did you download my odin and followed my instructions 100%?
Also don't use PIT or tik anything else just do what I said in the tutorial
And sorry I added a line to tutorial forget to say that you need to enter download mode first but I think you did that ?
GianniDPC said:
Tutorial:
1. Start ODIN
2. Turn of your phone so that to go to Download Mode. The download mode can be entered by pressing Volume down Key + OK button, and holding both simultaneously press the Power Button.
2. Choose PDA and select the downloaded File (SS_DL.dll not needed 'delete it')
3. Leave everything as it is and click 'Start'
4. On your phone follow instructions after flashing is complete
Odin download: Odin
Click to expand...
Click to collapse
i did it exactly as above... fails to write every time
i tried with every usb port i have but it doesn't work...
djbasspower said:
i did it exactly as above... fails to write every time
i tried with every usb port i have but it doesn't work...
Click to expand...
Click to collapse
Ok do you have KIES installed if not Install it (Maybe reinstall it)
Make sure KIES is closed when ODIN is opened (another thing I recommend to do is go to recovery on your phone and wipe data factory reset and wipe cache) Then try again
Hi, i just bought a new Galaxy y pro.
I'm Italian and my current fimware is XXKJ4 ...
I want update it but kies doesn't find my phone, i try to reinstall kies, with another PC but is the same...
What is the lastest or the best firmware for this phone?
Also, when i try to flash with Odin, give me a FAIL
Please, help me ! thanks
I have the answer for the problem!
Ok everybody these firmwares are no ready to use with ODIN, that's the problem. You need to convert these KIES firmware to ODIN ready to flash files with Doky73's tool --> SplitFUS2 or request him the firmware in this threat.
And please don't forget to say thanks to Doky and me
Which ROM to use for a B5510 bought in Czech Republic?
djbasspower said:
Hi!
Thanks for the os!
I tried the tutorial above a couple of times but odin gets the following error:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> B5510XXKJ2_B5510OXAKJ2_B5510XXKJ2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> sbl.bin
<ID:0/004> NAND Write Start!!
<ID:0/004> BcmCP.img
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I have a galaxy y pro gt-b5510.
android version 2.3.6
basehand version b5510xxkj2
kernel version [email protected] #16
build number gingerbread.xxkj2
i've entered in download mode, the display confirmed with:
odin mode
product name: gt-b5510
custom bin down: no(0 counts)
current bin: samsung official
Downloading...
do not turn off target!!
any suggestions?
thanks!
Click to expand...
Click to collapse
I ran into this thread and tried the same thing. After much searching, I found references to this thread and/or this tool to use. It looks like the problem with this firmware is it is all in one package, and needs to be split. See the links below:
http://forum.xda-developers.com/showthread.php?p=26251171 - look at reply #6
http://fahmi1597.blogspot.com/2012/08/android-how-to-split-onepackage.html - how to split a .tar.md5 file into the subpackages, if it is all in one.
---------- Post added at 01:02 AM ---------- Previous post was at 12:29 AM ----------
pshaww said:
I ran into this thread and tried the same thing. After much searching, I found references to this thread and/or this tool to use. It looks like the problem with this firmware is it is all in one package, and needs to be split. See the links below:
http://forum.xda-developers.com/showthread.php?p=26251171 - look at reply #6
http://fahmi1597.blogspot.com/2012/08/android-how-to-split-onepackage.html - how to split a .tar.md5 file into the subpackages, if it is all in one.
Click to expand...
Click to collapse
I can confirm it works fine using Odinatrix (from the second link above. I used the firmware mentioned in this thread. (by the way, the OP didn't mention it is password protected - password is 'android'). I let Odinatrix split up the firmware - super easy to use, just follow the instructions in the second link above.
I then flashed CSC, MODEM, and PDA - nothing else. I didn't repartition - just left at auto reboot and f. reset time. Now flashed fine and is restarting.
AN ADVICE
Hello sir...maybe your tutorial will be better if you can give us some photos/ScreenShots of flashing steps...
:highfive:
aligh9 said:
Thanks a lot
This is what you wanted:
PDA: B5510JPLI1
PHONE: B5510XXLH3
CSC: B5510OJPLF1
Sent from my GT-B5510 using Tapatalk 2
Click to expand...
Click to collapse
@OP.. I am asking in place of him as he still doesnt have 10 posts to post here.. Can you please kindly upload U.A.E firmware B5510OJPLF1 which is available in samfirmware.com.. Thank you..
Sorry, but rom with Italian language ?
These firmwares are not flashable with Odin (Gives you an error) search the Internet for the right packages (you should succeed I fixed a friend his Galaxy Y Pro with that)
EDIT: I will try to update this thread even if I have a Xperia Mini now.
why is this in s5360 thread? :laugh:
zenxus31 said:
why is this in s5360 thread? :laugh:
Click to expand...
Click to collapse
well, you can report it..
Its in sgy section because all variants of sgy like duos , pro duos, pro come under sgy section.. so.. I guess it can be moved to duos development section.. but no harm if its here..
____________________________________
“If you wait to do everything until you’re sure it’s right, you’ll probably never do much of anything.” –Win Borden
i Tried flashing My galaxy Y pro with ODIN but it keeps Stucking i recovery img all the time, tried different ports and only 1 worked
is there any help ?

Recover from soft brick

Hello everybudy here is a guide to recover from soft brick(I ave only tested it on S7500 not other)
So do it at ur own risk
First download odin3 v1.85
Download stock firmware for ur cont
Extract both in a particular folder
Open odin
Go to Download mode in ur phone and press volume up
Connect ur phone to pc
If odin shows a yellow mark then u are ready to proceed
Mark PDA & and selct file
Click start in odin
Keep patience
After process is over odin will show pass
Now ur phone will reboot
(DO NOT REMOVE USB CABLE TILL ITS REBOOTED PROPELY)
Complete the setup
Now again switch off mobile as as the process has not been completed yet
Go to recovery mode (this time it would be stock recovery not cwm)
In recovery mode select wipe data factory reset and wipe cache partition
Reboot.
Now u are done!!
HIT THANKS IF I HELPED
Odin-http:// www.androidlegend.com/dl/Odin3_v1.85.zip
Stock firmware(pda)- http://www.tsar3000.com/Joomla/inde...ace-plus-firmwares&catid=55:samsung&Itemid=82
Sent from my GT-S7500
whats new in this there is a sticky in which hole process is shown correctly
and 1 thing -
you should edit PDA ...it is different for different countries
you provided the firmware which is not for Indian users
http://www.sammobile.com/firmwares/
this is were you can get firmware for your own country !!
Ok i have edited pda and u can check the link
Also, I am a Indian and have tried this and its almost same
Only we have to change the language
Thanks any way
Sent from my GT-S7500
I had searched but it was not in q n ans. So i put it in this section. I dont know about stickies as i am new to this
Sent from my GT-S7500
There has also a type of soft brick where you will not be able to access download mode. Then odin will not work
then use USB jig. See http://www.xda-developers.com/android/need-a-samsung-usb-jig-build-your-own/
Ya i know
Sent from my GT-S7500
[email protected] said:
Ya i know
Sent from my GT-S7500
Click to expand...
Click to collapse
I know that you know. It was not mentioned so I mentioned it.
Itz showing fail please help asap!!!!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> S7500DDMF2_S7500ODDMF1_S7500DDME1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> system.img.ext4
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
i tried its coming failed,i tried downloading odin and firmware again from sam mobile, evn removed kies still the same please help asap!!
Ashmit Poojari said:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> S7500DDMF2_S7500ODDMF1_S7500DDME1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> system.img.ext4
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
i tried its coming failed,i tried downloading odin and firmware again from sam mobile, evn removed kies still the same please help asap!!
Click to expand...
Click to collapse
Keep Odin open and change USB ports, remount the PDA & flash. Hope this helped, worked for me

[Resolved] [Q] Note 3 Sm-n900 root error odin FAIL! HELP!

I tried to root my sm-n900 note 3 and followed all the instructions to the letter on the forum and when I tried to root through odin, it says writing cache.img and I wait for a few minutes then it says FAIL, I unplugged then restarted my phone and it says "FIRMWARE UPGRADE ENCOUNTERED AN ISSUE, PLEASE SELECT RECOVERY MODE IN KIES AND TRY AGAIN" and now kies doesnt recognize my device anymore, So what can I do now? I really want to root but damn samsung wont let me!
I see this in odin btw
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CF-Auto-Root-ha3g-ha3gxx-smn900.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> recovery.img
<ID:0/006> NAND Write Start!!
<ID:0/006> cache.img
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
UPDATE!
I tried using odin 1.85 to root, and now its stuck at cache.img it hasnt changed for maybe an hour now what?
UPDATE2
phew unticked autoreboot in odin and manually rebooted and everythings good
Sorry I could not tag your question due to failure with the mobile app. For starters I did not worry about using the auto-root option since I am not worried about tripping Knox counter. I prefer to flash twrp or cwm via Odin and then flash the current version of supersu from the recovery or if you are looking to install a custom Rom you can just flash it instead. Nothing against CF auto-root but this has always worked for me.
sm-900t: Powered by X-Note V13
FFTony said:
Sorry I could not tag your question due to failure with the mobile app. For starters I did not worry about using the auto-root option since I am not worried about tripping Knox counter. I prefer to flash twrp or cwm via Odin and then flash the current version of supersu from the recovery or if you are looking to install a custom Rom you can just flash it instead. Nothing against CF auto-root but this has always worked for me.
sm-900t: Powered by X-Note V13
Click to expand...
Click to collapse
Could you please explain that in noob terms?
firmware upgrade encountered an issue. please select recovery mode in kies and try ag
hi
i have same problem.
pls help me..
willzhang0 said:
I tried to root my sm-n900 note 3 and followed all the instructions to the letter on the forum and when I tried to root through odin, it says writing cache.img and I wait for a few minutes then it says FAIL, I unplugged then restarted my phone and it says "FIRMWARE UPGRADE ENCOUNTERED AN ISSUE, PLEASE SELECT RECOVERY MODE IN KIES AND TRY AGAIN" and now kies doesnt recognize my device anymore, So what can I do now? I really want to root but damn samsung wont let me!
I see this in odin btw
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CF-Auto-Root-ha3g-ha3gxx-smn900.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> recovery.img
<ID:0/006> NAND Write Start!!
<ID:0/006> cache.img
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
UPDATE!
I tried using odin 1.85 to root, and now its stuck at cache.img it hasnt changed for maybe an hour now what?
UPDATE2
phew unticked autoreboot in odin and manually rebooted and everythings good
Click to expand...
Click to collapse
Awesome... Your technique worked for me.
You just have to uncheck the auto reboot option. Its so simple.
Thanks a lot man!
i have this same problem..pls help me..even i unticked reboot option but its not working...stuck in da middle while rooting..pls help me..

Can not flash official firmware

Hello,
I want to flash to G920FXXU1AOD4 from G920FXXU1AOE3.
I tried to use Odin 1.85 and 3.04.
This is the error that I'm getting in Odin 1.85:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G920FXXU1AOD4_G920FOJK1AOD4_G920FXXU1AOCZ_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
Why can't I flash to this firmware?
Help...
r'n'b said:
Hello,
I want to flash to G920FXXU1AOD4 from G920FXXU1AOE3.
I tried to use Odin 1.85 and 3.04.
This is the error that I'm getting in Odin 1.85:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G920FXXU1AOD4_G920FOJK1AOD4_G920FXXU1AOCZ_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
Why can't I flash to this firmware?
Help...
Click to expand...
Click to collapse
Did you turn on USB DEBUGGING?
Hello again
I had the same problem with flashing rom with odin... I found a solution and explained it how to fix mine...
I hope it be helpful
http://forum.xda-developers.com/galaxy-s6/help/help-odin-stuck-start-write-nand-t3127992
k2evil said:
Hello again
I had the same problem with flashing rom with odin... I found a solution and explained it how to fix mine...
I hope it be helpful
http://forum.xda-developers.com/galaxy-s6/help/help-odin-stuck-start-write-nand-t3127992
Click to expand...
Click to collapse
Ok... I Solved my problem finally... I spent almost 3 days in forums to find a solution... So i give you guys a summary what I do:
1) Find my phone's pit file according to model and storage capacity (Mine is G920F 32GB)
2)Then the trick is use ODIN V3.10.6 insist of V3.09... http://forum.xda-developers.com/showthread.php?t=2711451
3)If you face with hidden.img problem, extract the rom's file and rename the file hidden.img to hidden.img.tar and flash it by ODIN (Put this file on AP)...
Wait for some minutes and there is where magic happens
Click to expand...
Click to collapse
I don't understand your solution.
What do I need to do with the pit file?
My device is also G920F 32GB.
The USB DEBUGGING is on.
r'n'b said:
I don't understand your solution.
What do I need to do with the pit file?
My device is also G920F 32GB.
The USB DEBUGGING is on.
Click to expand...
Click to collapse
I heard from someone that Stucking in Start Write NAND is because of pit file...
but forget about it.. try without pit file. download the lastest odin v 3.10
usually process fails when it try to flash hidden.img... if it happen for you, do the 3th step
k2evil said:
I heard from someone that Stucking in Start Write NAND is because of pit file...
but forget about it.. try without pit file. download the lastest odin v 3.10
usually process fails when it try to flash hidden.img... if it happen for you, do the 3th step
Click to expand...
Click to collapse
Finally I managed to flush the ROM
Odin3_v3.10.6 did the job.
Thanks!
Your welcome buddy... just don't forget to hit the thank button

[HELP] Odin Fail on GT-P5113 Tab 2 10.1

First off, I have TWO (2) of these guys. Same model number. I flashed 1 successfully. These came from a flea market. The one that upgraded successfully was working. The other one, was labeled "PARTS" and just bootloops.
This one, I am UNABLE TO GET INTO RECOVERY by pressing "PWR+VOL DOWN", unlike the first one. I AM able to get into DOWNLOAD mode and attempt to flash the 4.2.2 update like I did the first one.
The problem is ODIN is throwing a "FAIL!" on this one.
Code:
<ID:0/014> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> P5113UEUCMK3_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/014> Odin engine v(ID:3.1005)..
<ID:0/014> File analysis..
<ID:0/014> SetupConnection..
<ID:0/014> Initialzation..
<ID:0/014> Get PIT for mapping..
<ID:0/014> Firmware update start..
<ID:0/014> SingleDownload.
<ID:0/014> boot.img
<ID:0/014> NAND Write Start!!
<ID:0/014> FAIL!
<ID:0/014>
<ID:0/014> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I am using ODIN 3.10. Not sure if there is any way to force a recovery. I don't OWN these, they are a Co-Workers. Just curious if using a PIT file to repartition would be best, or if I need to flash a new bootloader or something. In DOWNLOAD mode, the screen says:
Odin Mode:
Product Name: GT-P5113
Custom Binary Download: No
Current Binary: Samsung_Official
Any help?
Update:
Tried to use a PIT file to restore the partition tables, but all I get is "There is no PIT Partition". I have tried a few PIT files for the 5110/5113 as well as trying to flash it standalone and with said ROM. Not sure if there are any other methods or steps involved.
Any help would be awesome!

Categories

Resources