How to open phone? - AT&T, Rogers HTC One X, Telstra One XL

How to open phone? - AT&T, Rogers HTC One X, Telstra One XL

Anyone know how to physically open this phone? For example I want to change the screen glass? Thanks!!!!
HTC One XL - Rogers

You need some kind of prying tool. You start at the bottom underneath the capacitive buttons. Stick the prying tool between the screen and housing and lift the screen up. You will have to work your way around the phone and pry the sides as well.
Eventually you will be able to remove the phone from the white housing.
That's as far as I got. I'm not brave enough to go further.

sal14m said:
Anyone know how to physically open this phone? For example I want to change the screen glass? Thanks!!!!
HTC One XL - Rogers
Click to expand...
Click to collapse
Use a plastic spudger tool and basically separate the body from the screen, from there you have to disconnect the speaker and some other things that are on the body but attach to the motherboard.
After that you'll have to remove the motherboard and it's components, then the battery, and then you will probably be able to switch out the screen.

Since the glass/digitizer is optically bonded to the screen, would replacing the prior require a heat-gun or hairdryer and some sort of optical glue?

Related

Replacing screen.

I'm trying to replace the screen on my Arrive. But I can't figure out how to get the screen out. It looks like I can pop out the back behind it, but I can't figure out how it disassembles. is there a tutorial out there or something?

To replace the *glass*, which I'm assuming is what you mean (not the LCD - they're separate in this phone, for once!)
Follow the "replace HTC 7 Pro memory card" instructions to remove the first back piece. Next, remove the screws in the next plastic back and remove it as well (it'll be easier to remove as it's just screws and contacts - no clips or wires). At this point you should see an exposed PCB, and your phone's hinge (a set of springs).
Undo the 4 screws holding the hinges on, along with the two screws holding the "pop-up" bezel (there are access holes for them - it'll make sense once you get there).
Slide the hinges across the back of the display (like you were opening the phone, but pull by the hinges! otherwise you'll break the display cable) and you'll see two screws which hold covers onto the back of the display panel. Undo the one for the bottom panel and pry the plastic bottom panel off from the back to gain access to the touchscreen connector.
Next, take a heat gun to your display and pry the glass off - I hope your glass is shattered and that's why you're replacing it because otherwise this is hugely difficult - the glass is glued on and glued on tight!
You'll see the glass is attached via flex cable thru the plastic to a connector inside the back - this is why you had to take your whole phone apart! Carefully lift the tape covering the connector, flip up the connector, and remove the old touchscreen ribbon cable and chip. Thread the new one through and reverse steps to install.
I just used the remainder of the old glue to stick my new display on, by setting it under some heavy books overnight. Your mileage will probably vary - I'm not too picky and a slightly loose/mushy screen beats a shattered one for me so I just left it at that.
Otherwise you'll probably have to figure out how to glue the display glass back on properly.

http://forum.ppcgeeks.com/htc-arrive-7-pro/144512-htc-arrive-disassembly.html
Sent from my PG41200 using XDA Premium App

Generally, I would look for one of the teardowns that have become popular for when devices are first released.....sort of the one-upping of the unboxing video.

I had trouble finding a decent disassembly - the "big" disassembly sites (ifixit etc.) seem to have ignored the Arrive and all I found on YouTube was horrid quality and mostly worthless.
That ppcgeeks thread is definitely the best resource for pics - I found that peeling the metal tape and unplugging the entire display/front piece was unnecessary by exercising some care to not break the ribbons, and I found that I needed to go a step further and remove the bottom (behind the buttons) plastic cover from the display piece to access the touch digitizer flex cable (which was behind some horribly obnoxious yellow tape).

Replace Screen under digitizer
Does anyone have a walk through on how to change the actual screen under the digitizer? I took the whole phone apart, but everything on the screen half of the phone seems to be glued.
I figured i would look around before just prying it open.
Any help is greatly appreciated.

Someone please post pics about last steps?
I was able to take hinges out of way but I am not sure if I need to peel off the metalic film. Hence I still have my top cover with glass attached with the back of the phone.
After I reach I have no idea what to do and now putting together my phone without changing broken glass!

Screen replacement experience's ?

Evening all.
So my beloved DHD needs the screen and digitizer replacing. Ive done the necessary reading/ searching and ive also located what appears to be a decent replacement.
Here is the thing.......
Has anyone successfully managed to do the replacement and keep the " Home, menu, back, search " buttons lighting up post screen replacement ? If so i would really appreciate some pointers on how you did this.
Thanks in advance

i replaced a digitizer / display on my dhd once and did the same on some Hd2 before.
On DHD its really difficult to replace the screen / digitizer. You most likely damage the plastic frame around the screen and indeed the arrangement of the Leds are no easy too, but not too hard to maintain. I wouldnt change the screen of anyone others DHD, just my own.

Yes, ive read that the replacement process is somewhat fiddly / tricky and no i would'nt do it for anyone else either. Im going for a pre assembeled screen / digitizer.

digitalizer is glued on lcd and lcd is glued on the middle metal plate, removing lcd from the plate requires heating it and it sure isn't fun, even after heating it it is still hard to remove without damaging the plastic frame, if i were you i would take it to a service shop with already bought part and paied them to change it, trust me it is not worth the nerves and the time

I'm a very handy guy and I accidentally tore a ribbon cable separating the pieces glued together. It's very hard, worth paying someone.

alextheg said:
Evening all.
So my beloved DHD needs the screen and digitizer replacing. Ive done the necessary reading/ searching and ive also located what appears to be a decent replacement.
Here is the thing.......
Has anyone successfully managed to do the replacement and keep the " Home, menu, back, search " buttons lighting up post screen replacement ? If so i would really appreciate some pointers on how you did this.
Thanks in advance
Click to expand...
Click to collapse
yes, but it was a pain, hold the pieces in place with double stick tape and be careful not to bend them!

Yup I successfully managed to replace a digitizer but I'm also a trained phone technician.
The most important thing is to be very careful. You should never have to use force in order to disassemble a phone.
How to get the cracked digitizer off? Simple, use your oven.
* Place the display-module (Chassis, digitizer,LCD) on a tray, make sure the plastic parts don't touch the bottom, so that it doesn't melt.
* Heat the oven to about 80-100 degrees celsius.
* The display should come off pretty easily.
* If you've done it properly, you can use the same adhesive that was one the chassis/frame if not you'll have to purchase some slow drying adhesive and carefully place it around the edges.
* Carefully move the light-guides on the bottom of the screen to the new digitizer. There's a small amount of adhesive on them so don't get any sweat on them. If they don't stick just use a very very, I'm talking pixel size amount of adhesive on it to get it to stick.
That's about it. Thread the flex-cable around the display and use a tweezer to connect it.

[Q] Nexus S glue that holds screen to phone

Hey, I've done extensive searching on Google and these forums, something that is always left out is ABOUT GLUE.
I had a broken Nexus S screen and I changed my screen on the phone with a new one bought on eBay, the new screen works flawlessly but the OEM screen has a sort of adhesive tape that would make it adhere to the phone frame. And usually, all instructions for removing the screen talks about using some kind of a heat gun to make the glue loose.
Well the problem is that the new screens don't have this adhesive, I was wondering if anyone can suggest a kind of glue that would do the job for attaching the new screen to the phone. Right now as it is, the screen is only held in place to my phone by the wire which connects it to the phone's circuitboard.

on a german forum i've read a users experience... he used regular "super-glue" that you can buy everywhere. the one that makes your fingers stick in like 4-5 seconds.
he put little spots of glue everywhere the screen touches the plastic and quickly pushed the screen onto it. seems legit if you ask me - the screen doesnt weigh that much after all.

http://www.repairsuniverse.com/adhesive-strips-for-touch-screens.html

murfi said:
on a german forum i've read a users experience... he used regular "super-glue" that you can buy everywhere. the one that makes your fingers stick in like 4-5 seconds.
he put little spots of glue everywhere the screen touches the plastic and quickly pushed the screen onto it. seems legit if you ask me - the screen doesnt weigh that much after all.
Click to expand...
Click to collapse
That is ideally what I would really like to do instead of dealing with adhesive strips and then cutting the pieces to fit. I live in Germany now and the electronic store here said you can absolutely not use superglue and suggested instead that I used double-sided tape you buy from a photo store (Doppelseitiges, dünnes Klebeband).
What is the name of this 'super-glue' in Germany?

JoeyZazza said:
That is ideally what I would really like to do instead of dealing with adhesive strips and then cutting the pieces to fit. I live in Germany now and the electronic store here said you can absolutely not use superglue and suggested instead that I used double-sided tape you buy from a photo store (Doppelseitiges, dünnes Klebeband).
What is the name of this 'super-glue' in Germany?
Click to expand...
Click to collapse
Sekundenkleber

What if it broke again? I doubt you would be able to remove it if super glue it's used

Evo_Shift said:
What if it broke again? I doubt you would be able to remove it if super glue it's used
Click to expand...
Click to collapse
You're probably right but if it breaks again I'll just write off the phone as fully depreciated in my head.

Was the replacement one of these:
http://www.ebay.com/itm/All-New-Out...773?pt=LH_DefaultDomain_0&hash=item3a77cd07e5
or was it a full unit that go over $100?

need advice how to patch up my physically damaged M7

Alright, I did send sms on my bicycle which resulted in I did drop the phone on the ground. Luckily I had ad NILLKIN glass screen protector, which did save most of the phone . I have ordered a new Nillkin screen protector from Aliexpress. And I hope to patch up this phone so it looks good again. How would you have done ?
As you can see at the bottom in the pictures there is physically damage, you can you see the screen bleeding thru also the huwawei logo is damaged.
My idea is UNDER the NEW Nillkin screen protector I will try to mask these "holes" so the screen is not beelding thru anymore. What material should I use to patch up these holes.. also.. how to repar the logo ? can I print it out on my computer printer ? it might look **** on paper but UNDER the glass protector it might look a lot better.
All creative ideas are appreciated, I have high hopes the phone will look good again..
And hopefully my phone will surrive until the M8 release.
Just to let you know desipite the glass look damaged like this the phone is still fully functional!!

ouch i can feel with you.
How about some black film, black paper or everything else that is black and thin

Yes some black material for sure.. Black film would be perfect in guess.. Just wonder where to get it also some black glue at the sides also..

Maybe you can find a front replacement? - http://www.ebay.com/itm/New-Front-O...-Parts-For-Huawei-Ascend-Mate-7-/201270995814
http://www.ebay.com/itm/Original-Re...s-Lens-For-Huawei-Ascend-Mate-7-/141549809429
Don't put a huawei printed logo there lol it will look bad and cheap.

alexre123 said:
Maybe you can find a front replacement? - http://www.ebay.com/itm/New-Front-O...-Parts-For-Huawei-Ascend-Mate-7-/201270995814
http://www.ebay.com/itm/Original-Re...s-Lens-For-Huawei-Ascend-Mate-7-/141549809429
Don't put a huawei printed logo there lol it will look bad and cheap.
Click to expand...
Click to collapse
Nice man might be a very good alternative! But how easy is it to change it really?
Do I need a heat gun for that?

Don't know. I don't advise to do it yourself , just go with the phone to any service, I'm sure they know how to do the operation. Or maybe you have an huawei service near you.
Or...if you have the courage go for it ) - https://www.youtube.com/watch?v=nDiaQOzCvfE & https://www.youtube.com/watch?v=lUl8dCuhBGw
Joke man, don't do it yourself if you don't have experience

alexre123 said:
Don't know. I don't advise to do it yourself , just go with the phone to any service, I'm sure they know how to do the operation. Or maybe you have an huawei service near you.
Click to expand...
Click to collapse
I have done some smartphone repair myself, I changed the USB board on my old Galaxy Note 1.
I bought a smartphone repair kit with a few tools and very small screwdrivers. To change the glass is probably not much harder, but I need to know if I need a heat gun since I do not own any yet Hopefully it is not needed..but I would assume so...

I might also add the reason I bought a screen protector was that the original glass underneeth have a small crack too that goes accross the entire screen but it s quite invisible besides from certain angels.. so to change that screen to would actually be amazing..and it would make the secondary value when I sell this when M8 is released be a lot higher..

I think you need one. Look at the second yt movie at 22:34. Have an hair dryer?
https://meta.ifixit.com/Answers/View/3523/Using+a+hairdryer+instead+of+a+heat+gun
Hair Dryer vs Heat Gun
https://www.youtube.com/watch?v=9ELHDYjpLoc
If I was me I would go with the phone to a service. Anyway good to know Nilkin tempered glass do the job, I have one also on my screen

alexre123 said:
I think you need one. Look at the second yt movie at 22:34. Have an hair dryer?
https://meta.ifixit.com/Answers/View/3523/Using+a+hairdryer+instead+of+a+heat+gun
Hair Dryer vs Heat Gun
https://www.youtube.com/watch?v=9ELHDYjpLoc
If I was me I would go with the phone to a service. Anyway good to know Nilkin tempered glass do the job, I have one also on my screen
Click to expand...
Click to collapse
Yes the Nillkin glass did its job but I think I was unlucky, that the bottom of the phone got under my bicycle tire.. it felt like it...
I recommend Nillkin, IT has very good Oleophobic coating, which makes the whole device a lot more enjoyable to use, but be careful whren you put it on non 100% straight surfaces it will slip onto the floor.
Alright it is more or less decided I will buy a new front cover with glass, I will make sure to get original parts with gorilla glass. Since the ebay link you linked to are chipped from china I guess I can just order straight from alixpress instead...
I have heard singapore post have quite fast shipping compared to china post.

just one question is hard to see in the videos.. but do I really need to disassembly every component all the circuits boards just to change the front screen ? do I need to open the case at all when using the heat gun/hair dryer ?
If as in the every component and circuit board has to be disassembled it is over my competence probably... unless I am super careful..

Mutch better if you want to purchase an original front to replace it. Don,t know if you really need to take all the components of for replacing the front screen, but you can make some research on it or you can ask on other forums, maybe are others with more experience.

yes I understand..must decide tomorrow then.. because of shipping times a fast decision need to be made otherwise I will have to wait too long..

blackinfinity said:
yes I understand..must decide tomorrow then.. because of shipping times a fast decision need to be made otherwise I will have to wait too long..
Click to expand...
Click to collapse
Man I was repairing the whole Mate7 from the scratch!
If u shattered the screen ;
1.You will need new one which cost £40-£60 2.You will have to strip the WHOLE phone which is pain!
3.You will have to open the back cover,which is very hard process.You will need hard force to pop back cover from hinges.(first you need to remove small bottom cover which is plastic.)You will have to pry it underneath is adhesive which holds that small cover firmly.
4.Once you manage to remove back cover you have to disconnect all flex cables.There are 3 black screws and 4 chrome screws(smae like two at bottom) which holds motherboard.
There is small black cover which covers all connectors and it is tricky to remove it,because left side is kind of locked under chrome metalic cover plate! You need to pry it slightly to the right to flip it upwards.Be careful! One black screw holds that small black plate!
Once you remove the motherboard, another and very very hard part awaits you!
5.Removing the battery!
You will need heat gun to remove battery but even that heat gun might ot help you to remove BIG battery without damage !!
I tried to remove battery without damage but no luck.So I will advise you to buy new battery for mate7 mine cost me just £8 from china but I had to wait almost a month to deliver! Disaster shipping from china!
So if you apply lot of heat you might be lucky remove battery without damage.
But I was scared to apply too much heat on battery it could result in explosion or fire!!!
So I rather purchased one.
Once you remove battery, you can remove bottom part of phone which is usb board with speaker and plastics. It is up to you you dont need to remove it.
6.Removing the damaged screen from (middle) supporting frame!
This can be easy depends how screen is damaged. BUT
Here you have 2 options to replace screen.
A:You can buy screen without supporting frame which is harder and more work and heat gunning around the screen and prying screen from middle frame.Needs like 30-40 seconds of heating around the screen not in the middle.
B:You can buy s reen with middle frame which is very easy.Screen is already fited in frame so you dont need to mess with very slim adhesive srtips around the screen(which I done)
Then you will have to remove all parts from middle frame. Ear speaker ,loud speaker usb board and replace it to new housing.
Once you will set the new screen you can put all parts back together..
Replacing screen for this phone is PAIN!
It really needs skills and be careful because it is very easy to scratch back cover.

XDADEVX said:
Man I was repairing the whole Mate7 from the scratch!
If u shattered the screen ;
1.You will need new one which cost £40-£60 2.You will have to strip the WHOLE phone which is pain!
3.You will have to open the back cover,which is very hard process.You will need hard force to pop back cover from hinges.(first you need to remove small bottom cover which is plastic.)You will have to pry it underneath is adhesive which holds that small cover firmly.
4.Once you manage to remove back cover you have to disconnect all flex cables.There are 3 black screws and 4 chrome screws(smae like two at bottom) which holds motherboard.
There is small black cover which covers all connectors and it is tricky to remove it,because left side is kind of locked under chrome metalic cover plate! You need to pry it slightly to the right to flip it upwards.Be careful! One black screw holds that small black plate!
Once you remove the motherboard, another and very very hard part awaits you!
5.Removing the battery!
You will need heat gun to remove battery but even that heat gun might ot help you to remove BIG battery without damage !!
I tried to remove battery without damage but no luck.So I will advise you to buy new battery for mate7 mine cost me just £8 from china but I had to wait almost a month to deliver! Disaster shipping from china!
So if you apply lot of heat you might be lucky remove battery without damage.
But I was scared to apply too much heat on battery it could result in explosion or fire!!!
So I rather purchased one.
Once you remove battery, you can remove bottom part of phone which is usb board with speaker and plastics. It is up to you you dont need to remove it.
6.Removing the damaged screen from (middle) supporting frame!
This can be easy depends how screen is damaged. BUT
Here you have 2 options to replace screen.
A:You can buy screen without supporting frame which is harder and more work and heat gunning around the screen and prying screen from middle frame.Needs like 30-40 seconds of heating around the screen not in the middle.
B:You can buy s reen with middle frame which is very easy.Screen is already fited in frame so you dont need to mess with very slim adhesive srtips around the screen(which I done)
Then you will have to remove all parts from middle frame. Ear speaker ,loud speaker usb board and replace it to new housing.
Once you will set the new screen you can put all parts back together..
Replacing screen for this phone is PAIN!
It really needs skills and be careful because it is very easy to scratch back cover.
Click to expand...
Click to collapse
ehhm... good luck OP

blackinfinity said:
Hello and thanks, I appreciate your detailed instructions.
But I need to say one really IMPORTANT THING
IT IS NOT THE SCREEN THAT I NEED TO CHANGE THE ACTUAL SCREEN AND LCD IS WORKING PERFECTLEY WHAT I NEED TO CHANGE IS THE Front Screen Outer Glass Lens. i HAVE HIGH HOPES THAT IF I ONLY CHANGE THIS I DO NOT NEED TO DO ALL THE INSTRUCTIONS YOU DO SINCE I AM ONLY CHANGING THE GLASS NOT THE ACTUAL SCREEN, IT IS A VERY IMPORTANT DIFFERENCE BETWEEN SCREEN AND OUTER GLASS AND FRONT. I HOPE YOU WILL READ MY POST AND GIVE ME AN UPDATE BEFORE I PUSH THE BUY BUTTON THANKS!
This is the part I was going to order it is just the glass no lcd screen.
Click to expand...
Click to collapse
Sorry but you are like 10 year old child..
So u wanna change your ''front Screen Outer Glass Lens'' ??? (that is damn long name for glass )
You have so much hopes ? OK .. go on .. I leave you to it ..
I wish you very best of luck ..
''''IT IS A VERY IMPORTANT DIFFERENCE BETWEEN SCREEN AND OUTER GLASS AND FRONT''
DDDDDD this was so funny :laugh: :good:
Fingers :fingers-crossed:

You was talking about changing the lcd not only the front Glass. I just wanted to make sure you need to do all the instructions to change only front glass. The lcd is working..

blackinfinity said:
You was talking about changing the lcd not only the front Glass. I just wanted to make sure you need to do all the instructions to change only front glass. The lcd is working..
Click to expand...
Click to collapse
And I will give you one last advice ; that my detailed post above I explained you how difficult it is .. YOU want to change glass only ??
And what you think, you can just do it without stripping phone apart ?? Are you magician ? You would have to open phone anyway !
And replacing glass on your screen, do you have any idea how you gonna do it? Removing glass from LCD is x10 TIMES hard that my instructions above man !
So you basically adding even more, harder work to hard work ..!
Do you even have
1.LCD separator heat machine ??
2.Cutting line wire ??
3.Cleaning alcohol chemicals ??
4.Optical clear adhesive glue ??
5.Ultraviolet curing lamp ??
Come oon man ...
I told you I wish you very best of luck..

This guy want to do the exact same thing - https://www.youtube.com/watch?v=O8HNBtl9MwI
You have the all process here - https://www.youtube.com/watch?v=nDiaQOzCvfE & https://www.youtube.com/watch?v=lUl8dCuhBGw
Take a look and decide if you want do it yourself and risk to mess things up or go with the phone and the replacing part to a service and let someone who did this before.

Screen Glass Replacement

Did anybody try replacing the glass screen on the LG G5? Not the whole digitizer, screen only.
Looks like replacement glass is found quite cheap.
http://www.ebay.com/itm/OEM-Front-O...eplacement-For-LG-G5-H820-VS987-/222227276105
There is a crack on my screen, the touchscreen is perfect. Is there a procedure somewhere that can be followed to get it done? I see a lot of videos for a complete teardown. But is it possible to just use a heatgun to take the glass off and put the new one in?

These display modules are oftenly replaced altoghether, because replacing only the glass requires it to be really precisely fitted and hermetically glued, you can probably try to seperate the digitizer from the display, but you may end up with a some dust underneath the glass or some unwanted gaps.

suhridkhan said:
Did anybody try replacing the glass screen on the LG G5? Not the whole digitizer, screen only.
Looks like replacement glass is found quite cheap.
http://www.ebay.com/itm/OEM-Front-O...eplacement-For-LG-G5-H820-VS987-/222227276105
There is a crack on my screen, the touchscreen is perfect. Is there a procedure somewhere that can be followed to get it done? I see a lot of videos for a complete teardown. But is it possible to just use a heatgun to take the glass off and put the new one in?
Click to expand...
Click to collapse
I had a crack on my screen at the top of when it fell down on concrete floor. I had to buy the whole display with glass and digitizer for about 130 euros. I did not know that you can just buy the glass and replace it with a lower price. Oh well... but if you want to separate the glass from the digitizer or anything what is glued, always use the heatgun. You can also use the hairdryer. I had to replace a battery by opening up a back cover with a hair dryer. For separating the glass from the digitizer you have to heat it up very often, pry it open and hold at several spots, to avoid breaking components. It s quite difficult but take it slowly.

fosunite said:
I had a crack on my screen at the top of when it fell down on concrete floor. I had to buy the whole display with glass and digitizer for about 130 euros. I did not know that you can just buy the glass and replace it with a lower price. Oh well... but if you want to separate the glass from the digitizer or anything what is glued, always use the heatgun. You can also use the hairdryer. I had to replace a battery by opening up a back cover with a hair dryer. For separating the glass from the digitizer you have to heat it up very often, pry it open and hold at several spots, to avoid breaking components. It s quite difficult but take it slowly.
Click to expand...
Click to collapse
So, if I crack my screen I need to get a screen replacement with frame or just screen replacement?
Screen replacement with frame
https://www.fixez.com/store/lg/lg-g5/lg-g5-display-assembly-with-frame
Screen Replacement
https://www.fixez.com/store/lg/lg-g5/lg-g5-display-assembly-lcd-and-digitizer

You can get without the frame, you will just need to heat up the glue between the frame and old screen to cut through the glue to remove the frame. They cover it on the instruction video on Fixez.

Database Info

welcome