Related
pre Requisites:
- All the data present in your Galaxy FIT needs to be backed up ONLY by following the below mentioned steps so as to ensure that just in case if the data gets lost or corrupted.
- Charge left in the device should be minimum 60% so as to make sure that the phone doesn’t get turned Off in the middle of firmware update. Enable the USB Debugging in your device from the path “Settings > Applications > Development > USB debugging”
So,assuming that you have followed all the instructions mentioned above you now need to proceed further for procedure.
Procedure to Update
- Download Gingerbread 2.3.6 Package & odin-beni-ss.dll for Fit.zip in your computer after which you need to extract the same.If Promted For Password then You Should Enter Password as “sampro.pl”.
For 2.3.6 Update Package- http://hotfile.com/dl/140199372/0b98375/GT-S5670_INU_S5670DDKT1_S5670ODDKT1_S5670DDKT1.rar.html
- Match the extracted files from the below shown screen capture, even if single file is missing then you need to check with the extraction or download process.
- From extracted files, open Odin executable file and turn Off the phone so as to enter the device in the download mode.
- Now, you need to enter the by holding the Volume Down button + the Home key button (the middle button). While holding these both buttons, you need to switch ON your device. Just in case if the device boots in the normal mode then you will have to again try the process of entering into the download mode
- After entering the phone in the download mode, connect the device to the computer while keeping the Odin opened. Within a minute, the ID : COM section will turn yellow which will mean that all the drivers have been successfully installed and you are now ready to proceed to the next step.
- Click on the “OPS” option in the Odin to select the below mentioned file, tick on “One Package” option and then select the One Package option as mentioned below.
OPS – BENI_v1.0.ops
One Package – S5670DDKT1_S5670ODDKT1_S5670DDKT1_HOME.tar.md5
- Click on Start and then wait for the device to get restarted. Once the device gets restarted, you will be asked to enter the Google Account credentials. Once you see the home screen in your phone, disconnect the connected phone.
Congratulations!!! You have successfully update ur android with 2.3.6 Gingerbread Firmware
_______________________________________________________________
Press THANKS button If I help U in any manner
Hi!
Does this firmware includes greek language?Thanks!
may be no...
Because DD is for india:thumbup:
Sent from my GT-S5670 using xda app-developers app
Do you know where i can find or what is the name for the firmware to search?Also i have a greek galaxy fit with 2.3.6,do you know how to make a full backupo of this firmware?Thanks!
i guess everyone knows this
zafisinl said:
Do you know where i can find or what is the name for the firmware to search?Also i have a greek galaxy fit with 2.3.6,do you know how to make a full backupo of this firmware?Thanks!
Click to expand...
Click to collapse
http://www.sammobile.com/firmware/
In search write s5670.
password
what is the password for this file????
It's witten over there on sammobile
Sent Via XDA™ Premium
Password
rajmi said:
what is the password for this file????
Click to expand...
Click to collapse
Read the first post carefully
Pasword : sampro.pl
The rar file just has the md5 file, where can I find the other files? I tried manually downloading the files from different locations but it just sits at downloading mibib and doesn't do anything. The flashing process just sits at downloading MIBIB and doesn't go anywhere, I have tried waiting for as long as 30mins, now the mobile doesn't even start with the previous firmware. When started it shows an icon like connection problem between a computer and mobile right after the initial samsung logo and sits there.Please help
zafisinl said:
Hi!
Does this firmware includes greek language?Thanks!
Click to expand...
Click to collapse
Most probably it does.I flashed mine with a stock russian rom.the phone started in russian but you can easily navigate through the icons to settings and change the language.I turned it to greek
Just saw the heat on the GT-P6210 UK firmware release and checked on Samfirmware.
Flashed this using Mobile ODIN directly OVER the KL3 deodexed firmware, no major issues so far (unable to set voicemail number).
All settings/prefs/apps preserved
Download link from Hotfile, feel free to mirror elsewhere
http://www.hotfile.com/dl/162811167/9e67b52/P6200XXLQ1_P6200OXALQ1_ATO.zip.html
Beware, extracted, this file is nearly 850Mb in size
Also, thanks to anyone who roots this!
Aaron.
P.S. Screenshot
https://plus.google.com/u/0/111032879558038139743/posts/aD54hVuaVBz
-----
** UPDATE **
Brand new UK P6200 firmware available dated November 2012
PDA: P6200XXLQ7
CSC: P6200XEULP1
http://www.hotfile.com/dl/179423658/bf830d8/P6200XXLQ7_P6200XEULP1_XEU.zip.html
Same as previous. I flashed this directly over my previous firmware using Mobile Odin Pro. I had to flash SuperSU binaries afterwards to gain proper root access.
Root is easy for this firmware!
When flashing via Mobile Odin, clear the flash for recovery image (i.e. do not flash recovery)
Then flash SuperSU afterwards via recovery
http://download.chainfire.eu/204/SuperSU/CWM-SuperSU-v0.94.zip
how much it take time, i flash with mobile odin about 20 minute ago and my tab still on samsung logo !
It should take up to 7 minutes to complete the process, including boot up.
ali_ge said:
how much it take time, i flash with mobile odin about 20 minute ago and my tab still on samsung logo !
Click to expand...
Click to collapse
Took mine around 5 minutes to flash, then another few mins to get to the "upgrading screen" (which is simply android creating the relevant dexes).
acolwill said:
Took mine around 5 minutes to flash, then another few mins to get to the "upgrading screen" (which is simply android creating the relevant dexes).
Click to expand...
Click to collapse
hi can i just flash this with my stock p6200?
stock baseband kernel etc.
Justinhopaolo said:
hi can i just flash this with my stock p6200?
stock baseband kernel etc.
Click to expand...
Click to collapse
Should be no issues. I *would* flash the CWM recovery tho.
Uhm, for some strange reason none of my 2 PCs is able to see P6200 while in recovery mode. Everything is working fine if I connect my GS3 to those PCs. Any clue?
Try using Mobile Odin ;-)
It has worked pretty well for me.
Edit : I had a stock ROM / RECOVERY / ... Only rooted my device.
i'm mirroring the ICS Austria Firmware on media fire. Feel free to download.
part1 - part2 - part3
can i install roms without using an sd card?
Justinhopaolo said:
can i install roms without using an sd card?
Click to expand...
Click to collapse
yes.. but use odin.
motosuki said:
yes.. but use odin.
Click to expand...
Click to collapse
In another thread you say no. What's your final answer
Sent from my GT-P6200 using xda premium
Justinhopaolo said:
In another thread you say no. What's your final answer
Sent from my GT-P6200 using xda premium
Click to expand...
Click to collapse
you need to use pc + odin to flash this firmware. it doesn't require external sdcard. it is different when you flashing custom ROM, you need external sdcard to put the zip file.
motosuki said:
you need to use pc + odin to flash this firmware. it doesn't require external sdcard. it is different when you flashing custom ROM, you need external sdcard to put the zip file.
Click to expand...
Click to collapse
Hi I'm sorry, I hope its not too much of a drag for you. Bit can you give me steps?
I already have the mobile Odin.
Sent from my GT-P6200 using xda premium
Justinhopaolo said:
Hi I'm sorry, I hope its not too much of a drag for you. Bit can you give me steps?
I already have the mobile Odin.
Sent from my GT-P6200 using xda premium
Click to expand...
Click to collapse
1. download samsung kies to get the correct driver for gt-p6200
2. download odin3 v.1.85
3. download Stock Firmware Austria - P6200XXLQ1_P6200OXALQ1_ATO.zip
4. install Kies
5. extract Odin3-v1.85.zip
6. extract P6200XXLQ1_P6200OXALQ1_ATO.zip until you get file P6200OXALQ1_P6200XXLQ1_P6200XXLQ1_HOME.tar.md5
7. turn off your tablet
8. enter download mode (press volume up button + power button about 5 seconds)
9. plug the usb cable to your pc and your tablet
10. run Odin3 v1.85.exe
11. check if pc recognize your tablet by seeing ID:COM turn yellow and "Added!!" message in the message box lower left odin window.
12. klik PDA button and put P6200OXALQ1_P6200XXLQ1_P6200XXLQ1_HOME.tar.md5
13. make sure to uncheck re-partition
14. click start
15. odin processing takes about 5 minutes, wait patiently.
16. if there's a "SUCCEED" in the message box, your tablet will restart
17. wait about 10 minutes, you should get your ICS boot to system
if it's not....
18. if your tablet didn't boot, you need to wipe cache / factory reset in the recovery mode
19. turn off your tablet.
20. press volume up + power button about 5 seconds.
21. do wipe cache / factory reset
22. reboot to system
23. it should be booting to system
if it's not...
contact nearest samsung service center
motosuki said:
1. download samsung kies to get the correct driver for gt-p6200
2. download odin3 v.1.85
3. download Stock Firmware Austria - P6200XXLQ1_P6200OXALQ1_ATO.zip
4. install Kies
5. extract Odin3-v1.85.zip
6. extract P6200XXLQ1_P6200OXALQ1_ATO.zip until you get file P6200OXALQ1_P6200XXLQ1_P6200XXLQ1_HOME.tar.md5
7. turn off your tablet
8. enter download mode (press volume up button + power button about 5 seconds)
9. plug the usb cable to your pc and your tablet
10. run Odin3 v1.85.exe
11. check if pc recognize your tablet by seeing ID:COM turn yellow and "Added!!" message in the message box lower left odin window.
12. klik PDA button and put P6200OXALQ1_P6200XXLQ1_P6200XXLQ1_HOME.tar.md5
13. make sure to uncheck re-partition
14. click start
15. odin processing takes about 5 minutes, wait patiently.
16. if there's a "SUCCEED" in the message box, your tablet will restart
17. wait about 10 minutes, you should get your ICS boot to system
if it's not....
18. if your tablet didn't boot, you need to wipe cache / factory reset in the recovery mode
19. turn off your tablet.
20. press volume up + power button about 5 seconds.
21. do wipe cache / factory reset
22. reboot to system
23. it should be booting to system
if it's not...
contact nearest samsung service center
Click to expand...
Click to collapse
is this the method if i want to flash other roms, like cm9?
Justinhopaolo said:
is this the method if i want to flash other roms, like cm9?
Click to expand...
Click to collapse
you need to use CWM recovery.
1. download CWM recovery
2. copy CWM file into your external sdcard
3. turn off your tablet
4. enter recovery mode, press volume up + power button about 5 minutes
5. use volume button to navigate and power button to choose
6. choose "apply update from external storage"
7. find p6200_CWMR_20111214.zip
8. push power button to choose, and wait until instalation finished
9. your tablet will reboot
to install CM9
1. download custom rom you want to install
2. put it in your external sdcard
3. turn off your tablet
4. enter recovery mode, press volume up + power button about 5 minutes
5. use volume button to navigate and power button to choose
6. choose "install zip from sdcard" and "choose zip from internal sdcard"
7. find the custom rom zip file
8. push power button to choose, and wait until instalation finished
9. choose go back until you find wipe data / factory reset
10. choose yes
11. choose wipe cache partition
12. choose yes
13. reboot system now
that should do it... and make sure you use the right custom ROM for your tablet model.
whenever ichoose apply update from external. it say no such directory or file etc..
howcome?
Justinhopaolo said:
whenever ichoose apply update from external. it say no such directory or file etc..
howcome?
Click to expand...
Click to collapse
did you succeed installing CWM? or you still trying to install CWM?
i make some correction in the tutorial... please read again.
This is latest GINGERBREAD.XILG1 firmware (August 2012) for GT-s5570i
Firmware downloaded from sammobile and split for ODIN using odinatrix.
This also works to unbrick ur 5570i
Steps:-
1)Download GT-s5570i.zip from http://www.mediafire.com/?qmb5m4tzznnbjpm
2)Open Odin3_v1.84 from folder ODIN.
3)For PDA select PDA_S5570IXILG1_S5570iITVLG2_S5570IXXLF3_HOME.tar
For PHONE select MODEM_S5570IXILG1_S5570iITVLG2_S5570IXXLF3_HOME.tar
For CSC select CSC_S5570IXILG1_S5570iITVLG2_S5570IXXLF3_HOME.tar
4)PIT/BOOT files are not required---leave blank !!!
5)Put device in download mode (Hold Vol Down + Home + Power) and connect to the PC via the USB cable.
6)Press the START button
7)Wait up to 5 minutes, after which will show PASS (do not touch anything until it comes out the word PASS!)
8)The phone will reboot itself
9)After the output will be written PASS disconnects the cell from the PC
Default language is Italian.You can always change the language.
If you want to ROOT i have included zip file to be flashed in ROOT folder
Wrong forum dude
"Addicted to XDA more then facebook.....lol"
this is not Galaxy Mini form ??
Can anyone link me to the forum where this does belong? Can't find it..
don't be so harsh guys...this thread might moved from mini section since mini plus is a lot similar with ours.
techno-update said:
Can anyone link me to the forum where this does belong? Can't find it..
Click to expand...
Click to collapse
i m not sure but i think its like the Y & Y Duos have same so mini also have the same
http://forum.xda-developers.com/forumdisplay.php?f=1314
Hi all i tried to flash i9003 galaxy SL from steps below to 2.3.6 , but the firmware zip file does not have MODEM, CSC and PDA files but only .dll file and tar.md5 file, where can i get the MODEM, CSC and PDA.
I download the firmwares from link below:-
http://www.tsar3000.com/Joomla/inde...alaxy-sl-firmwares&catid=55:samsung&Itemid=82
Firmware Update Steps:
Run Samsung I9003 Galaxy SL Downloader.
Check Re-Partition, Auto Reboot and F. Reset Time.
Click PIT button and select this file: latona_20110114.pit
Put your phone into download mode: Press Volume down + OK + Power.
Connect USB cable and the program will detect the phone's Com number.
Click Start button to download the PIT file to phone.
After it is Done Click on Reset button, then unselect Re-Partition box.
Click PDA button and select this file: I9003xxxxx-xxx...-PDA-low-CL890053.tar.md5 <<<<<<<<<<<<<<<
Click PHONE button and select this file: MODEM_I9003xxxxx_REV_00_CL889972.tar.md5 <<<<<<<<<<<<<<<<<
Click CSC button and select this file: GT-I9003-CSC-xxxxxx.tar.md5 <<<<<<<<<<<<<<<<<<<
Remove the battery, then enter Device into Download Mode again.
Click Start button to flash these files to phone.
Do not touch anything till you see PASS on the program window.
Do full reset by this Code: *2767*3855#.wares i download dont have CSC , PDA
suhailpuri said:
Hi all i tried to flash i9003 galaxy SL from steps below to 2.3.6 , but the firmware zip file does not have MODEM, CSC and PDA files but only .dll file and tar.md5 file, where can i get the MODEM, CSC and PDA.
I download the firmwares from link below:-
http://www.tsar3000.com/Joomla/inde...alaxy-sl-firmwares&catid=55:samsung&Itemid=82
Firmware Update Steps:
Run Samsung I9003 Galaxy SL Downloader.
Check Re-Partition, Auto Reboot and F. Reset Time.
Click PIT button and select this file: latona_20110114.pit
Put your phone into download mode: Press Volume down + OK + Power.
Connect USB cable and the program will detect the phone's Com number.
Click Start button to download the PIT file to phone.
After it is Done Click on Reset button, then unselect Re-Partition box.
Click PDA button and select this file: I9003xxxxx-xxx...-PDA-low-CL890053.tar.md5 <<<<<<<<<<<<<<<
Click PHONE button and select this file: MODEM_I9003xxxxx_REV_00_CL889972.tar.md5 <<<<<<<<<<<<<<<<<
Click CSC button and select this file: GT-I9003-CSC-xxxxxx.tar.md5 <<<<<<<<<<<<<<<<<<<
Remove the battery, then enter Device into Download Mode again.
Click Start button to flash these files to phone.
Do not touch anything till you see PASS on the program window.
Do full reset by this Code: *2767*3855#.wares i download dont have CSC , PDA
Click to expand...
Click to collapse
First of all post in the general section. Second, read a lot.
Thirdly, which firmware are you at present? If KPE, flash LF2. The new stock firmwares only have a single .tar file. No modem, csc or any other files needed. And download from here >> http://forum.xda-developers.com/showthread.php?t=1004647/
nbrian2012 said:
First of all post in the general section. Second, read a lot.
Thirdly, which firmware are you at present? If KPE, flash LF2. The new stock firmwares only have a single .tar file. No modem, csc or any other files needed. And download from here >> http://forum.xda-developers.com/showthread.php?t=1004647/
Click to expand...
Click to collapse
i dont know the firmware as the phone is bricked, i managed to get into firmware download mode but it gives me an error after flashing, i flash the pit file and then reset odin and then enter download mode again and select single firmware file and check PDA option but flashing fale.
What file do i download because i downloaded many firmwares gingerbread ones but they all have one single tar file.
Socon off all what box do i need to select if i am flashing a single file , PDA or phone or CSC.
Suhail
suhailpuri said:
i dont know the firmware as the phone is bricked, i managed to get into firmware download mode but it gives me an error after flashing, i flash the pit file and then reset odin and then enter download mode again and select single firmware file and check PDA option but flashing fale.
What file do i download because i downloaded many firmwares gingerbread ones but they all have one single tar file.
Socon off all what box do i need to select if i am flashing a single file , PDA or phone or CSC.
Suhail
Click to expand...
Click to collapse
Download KPE, the files from the link I gave you ^
and follow THIS guide carefully >>>
Misledz said:
2. Run Odin3 v1.83
3. Check Re-Partition, Auto Reboot and F. Reset Time.
4. Click PIT button and select this file: latona_20110114.pit
5. Set it to download mode : Press Volume down + OK first, then hold Power button.
6. Connect USB cable and the program will detect the phone's Com number.
7. Click Start button to download the PIT file to phone.
8. After it is Done Click on Reset button [Partition box should be unchecked automatically - Thanks to jaskir]
9. Click PDA button and select this file: CODE_I9003XXKPE_CL409735_REV08_user_low_ship.tar
10. Click PHONE button and select this file: MODEM_I9003XXKPE_REV_00_CL1041909.tar
11. Click BOOTLOADER button and select this file: APBOOT_I9003XXKPE_CL409735_REV08_user_low_ship.tar
12. Click CSC button and select this file: GT-I9003-CSC-MULTI-OXAKPE.tar
13: You should unplug usb cable, remove battery, insert battery and bring it back to download mode. I have never been able to bring it to download mode with usb plugged in. [Thanks to jaskir for this suggestion to make it clear to new users!]
14. Click Start button to flash these files to phone.
15. Do not touch anything till you see PASS on the program window.
16. Factory reset
17. [To fix issues that pertain] Reflash from steps 9 -15 again, No need of latona at this point.
Click to expand...
Click to collapse
Must you have any issue at any point, reply again.
The SL can never get bricked unless you flash a firmware not compatible with it
Sent from my Galaxy Nexus using Tapatalk 4 Beta
How can i flash a single file .tar.md5 with odin, becuause now all the firmwares come with a single file i.e. .tar.md5 unlike old firmwares have CSC, modem and PDA file
shall i put pit file first and then flash which option needs to be checked ?
This has become really confusing for me now.
Can i also put my phone in download mode and flash via KIES ?
Thanks in advance,
Suhail
suhailpuri said:
i dont know the firmware as the phone is bricked, i managed to get into firmware download mode but it gives me an error after flashing, i flash the pit file and then reset odin and then enter download mode again and select single firmware file and check PDA option but flashing fale.
What file do i download because i downloaded many firmwares gingerbread ones but they all have one single tar file.
Socon off all what box do i need to select if i am flashing a single file , PDA or phone or CSC.
Suhail
Click to expand...
Click to collapse
HELP NEEDED TO FLASH FIRMWARE IN SAMSUNG GALAXY SL GT-I9003
I have downloaded the firmwares suggested by you... Its not clear how to proceed with the flashing of the firmware, as the steps asked to perform by you are contradicting to your previous post -> As there is only only file i.e GT-I9003_XEO_I9003XWLF2_I9003OXXLF1_I9003XXLE4 and rest of the files i.e PHONE file: MODEM_I9003XXKPE_REV_00_CL1041909.tar, BOOTLOADER file: APBOOT_I9003XXKPE_CL409735_REV08_user_low_ship.tar, CSC file: GT-I9003-CSC-MULTI-OXAKPE.tar are not required. Please be specific what is to be done to complete the flashing procedure.
well i just wanna know how to flash with odin when you have one file for firmware and tutorials show 3 files, but whatever firmwares i download they all have one ta file and no 3 files as suggeted in tutorials.
Suhail
Flash first clean for mandatory starting
On CM10 Alpha 3 and all other basic Froyo, Gingerbread, ICS, JB
- drivers samsung.rar - 5.58 MB
- Open Odin 1.85 only !!!
- KPE FULL (do not forget the PIT) (Froyo only ! no forget bootloader)
reset odin then remove cable and battery after samsung logo
- LF2 (PDA only with Odin)
reset odin then remove cable and battery after second samsung logo
- CF Root LF2 (PDA only with Odin)
I followed all steps, but in STEP 2 when i download the file its iso and not not md5 or tar so i dont know how to proceed and flash it, i tried to mount it , burn it no sucess
Anyways i went to step 3 and flashed again, but phone gets stuck at boot screen samsung logo
Any
UNZIP ?§!
suhailpuri said:
I followed all steps, but in STEP 2 when i download the file its iso and not not md5 or tar so i dont know how to proceed and flash it, i tried to mount it , burn it no sucess
Anyways i went to step 3 and flashed again, but phone gets stuck at boot screen samsung logo
Any
Click to expand...
Click to collapse
Dude, if it's a zip file then extract it & use the file which is extracted.
Good luck!
Sent from my GT-I9003.
LoLaTiOn said:
UNZIP ?§!
Click to expand...
Click to collapse
Hi LoLaTiOn,
I have unzipped the CSROOT file, what I could see was a .img file where as while selecting the file in the ODin 1.85 it demands for a .tar file. Can you please further help in this and pass me the link for the actual file i.e CSROOTXXXXXXXX.tar file in the required format to flash the Android OS.
Rest all the files in the link provided by you are in the required format.
Siddhant Shankpal said:
Dude, if it's a zip file then extract it & use the file which is extracted.
Good luck!
Sent from my GT-I9003.
Click to expand...
Click to collapse
Hi Siddhant,
Anybody in the world knows that we have to unzip a zipped file before using it. The actual problem is that --> After unzipping the file , I see a .img file where as Odin requires a .tar file to flash the Android OS. I tried converting it into a .tar file by using a cygwin terminal but no luck. I also tried searching for the same file in other links (Websites) but still there was no luck.
Can you give a hand to help me out.
suhailpuri said:
Hi Siddhant,
Anybody in the world knows that we have to unzip a zipped file before using it. The actual problem is that --> After unzipping the file , I see a .img file where as Odin requires a .tar file to flash the Android OS. I tried converting it into a .tar file by using a cygwin terminal but no luck. I also tried searching for the same file in other links (Websites) but still there was no luck.
Can you give a hand to help me out.
Click to expand...
Click to collapse
U mentioned "step 2" that means u were stuck in DDLF2 flashing step. But now ur telling "CFROOT LF2" step.
Okay, now in this step u don't need to unzip this file & just flash it from odin as in PDA section.
But I hope ur able to boot into ur phone after flashing DDLF2 firmware.
Good luck!
Sent from my GT-I9003.
Siddhant Shankpal said:
U mentioned "step 2" that means u were stuck in DDLF2 flashing step. But now ur telling "CFROOT LF2" step.
Okay, now in this step u don't need to unzip this file & just flash it from odin as in PDA section.
But I hope ur able to boot into ur phone after flashing DDLF2 firmware.
Good luck!
Sent from my GT-I9003.
Click to expand...
Click to collapse
My bad, I have mentioned it earlier that I have tried flashing the same .img file in the entire process but no luck.
suhailpuri said:
My bad, I have mentioned it earlier that I have tried flashing the same .img file in the entire process but no luck.
Click to expand...
Click to collapse
Download this DDLF2 firmware & extract it. http://forum.xda-developers.com/showthread.php?t=2329200
1. After extracting, switch off your phone & go to download mode.
2. Open odin 1.85 on ur PC & connect ur phone to ur PC. Check, whether it is connected by the yellow signal.
3. First only flash .pit file from the extracted folder. Then remove battery & put it back then again go download mode.
4. Browse & select all respected files from the extracted folder. (Do not include bootloader file if ur coming back to stock from CM 10 based roms.)
5. Click start.
Good luck!
Sent from my GT-I9003.
stuck with the error plzz help flashed stock with odin but remains at setup connection
screenshot
It happened with me sometime back; I tried download mode & it worked. However, recovery mode Home & Power buttons is not accesible.
Take out battery. Re-insert it & "cafefully" press & hold Volume down & Home & Power buttons together & u will enter download mode(yellow triangle). Flash the firmware as usual & see if it works.
not working with one package file it remain at setup connection
1st goto download mode & flash via Odin. U still HAVE download mode. Download mode doesn't vanish in such a case.
This screen in the pic appears when u access download mode & without proper flashing, trying to switch on the phone again. So it shows that symbol.
Do as what I said in the post above.
while using odin
after some process
it get stuck on setup connection
Sanjay(SUN) said:
while using odin
after some process
it get stuck on setup connection
Click to expand...
Click to collapse
Have u made it to download mode or not yet?
done
Which firmware r u flashing? Use Odin v4.42 & filename of ops file should be exactly as BENI_v1.0.ops
I guess u need a froyo(4pkg) firmware.
I tried searching for nearly an hour but couldn't find.
Found the package file
Plz tell me the procedure to flash
Strictly follow the steps mentioned below:
Remember: Don't ever use firmwares made for GT-S5670i/GT-S5670L...etc. on devices like GT-S5670 (no appended alphabet here), coz it will brick ur phone.
First of all,
* Install samsung mobile driver on pc.
* Uninstall Kies(if installed); In some cases, it's also required to disable antivirus/firewall,...etc.(I don't know why).
* Preferably use laptop(for power backup & also it has good usb ports) with XP/Windows7(not Windows8)
* Goto "download mode" in the phone. Then connect it to pc.
* Open Odin v4.42.exe as administrator & you'll see "COM PORT MAPPING" box turned yellow(indicating that you've connected the phone to pc).
Please note that as soon as u select OPS file in the OPS field of Odin, the Odin straightaway displays the device model number in its title bar, regardless of whether ur phone is physically connected to pc or not.
Now set the files(according to which firmware u have) as follows:
For firmware containing 4 files(Note the beginning filenames)
OPS: BENI_v1.0.ops
BOOT: APBOOT_S5670.....
PHONE: MODEM_S5670.....
PDA: CODE_S5670.....
CSC: CSC_5670.....
Click "Start" & wait till Odin says "PASS". Don't touch ur phone during the process. Ur phone will reboot during the process & that's perfectly normal.
OR for firmware containing one file(Note the beginning filename)
Tick "One Package" field(below com port).
Now set the files as follows:
OPS: BENI_v1.0.ops
One Package: S5670...._HOME.tar.md5
Click "Start" & wait till Odin says "PASS". Don't touch ur phone during the process. Ur phone will reboot during the process & that's perfectly normal.
* Now ur firmware would have been flashed successfully. If ur phone bootloops(showing bootanimation again'n'again) then goto RECOVERY MODE(Press & hold Home+Power keys) & select "wipe data/factory reset" & "wipe cache partition"(Use "Volume up/down" to navigate up/down & "Home button" to select & "Power button" to go back to previous menu). Then select "reboot system now".
*DONE!!
Ur phone would be 100% alright now.
Please follow the sequence exactly as mentioned. U will not find any other way than this one. Although Screenshots are messy...I'm on mobile rite now
Hope this helps...!!
Using window xp but while running through administrater it ask for password but I have never done something like that
Sent from my A13-MID using XDA Premium 4 mobile app
Enter ur login password :- The password that u use when the pc is turned/powered ON.
& if u don't know of such thing then ask it from the system administrator.
Can u plzzz tell me the procedure
Sent from my A13-MID using XDA Premium 4 mobile app
I guess u don't know. So, only thing u can do(if u use others' pc/laptop) is kindly request them to allow u admin rights. Tell them ur phone's life is hanging in the balance & only they can save it.
Btw procedure is simple...U just need to enter admin username(if asked) & password in the "Open As Admin" dialog box of Odin.:thumbup:
And if u have ur own pc then u shouldn't have faced this problem.
my big bro have an laptop and when it boot it doesnot need password but while using run as adminstrator it is asking for a password
the only need is to make this phone a portable router i am having 2 pices of fit