Database Info

[Q] {Q}How to restore rom orginal?

Hi.
me need help for install or restore the rom Original Galaxy Fit GT 5670.
plz add step by step.
thanks a lot.
run now in JANA ROM v8.0.

Please, please, please look around in the forum.
http://forum.xda-developers.com/showthread.php?t=1838066
Sent from my CM7 GT-S5570I

me test not work.
usb driver install, But S5570_Odin_Multi_Downloader_v4.38 Not Found.

me test not work.
usb driver install, But S5570_Odin_Multi_Downloader_v4.38 Not Found.
Windows has stopped this device because it has reported problems. (Code 43)
Windows Me 8.1 Prowc x86.

Happy Flashing
AhrimanSefid said:
me test not work.
usb driver install, But S5570_Odin_Multi_Downloader_v4.38 Not Found.
Windows has stopped this device because it has reported problems. (Code 43)
Windows Me 8.1 Prowc x86.
Click to expand...
Click to collapse
AhrimanSefid said:
Hi.
me need help for install or restore the rom Original Galaxy Fit GT 5670.
plz add step by step.
thanks a lot.
run now in JANA ROM v8.0.
Click to expand...
Click to collapse
Hi @AhrimanSefid
You can find the required ODIN Firmware Package as you wish for the ODIN tool
http://www.sammobile.com/firmwares/ and put in the Device Model Number and download it
or complete Firmware Package of Gingerbread 2.3.6 DDKT3 you can find the link below
http://hotfile.com/dl/146050815/b3b9278/S5670DDKT3_S5670ODDKT2_INU.zip.html in case this link doesn't work please download the Packages from above link as I can't check it from my office so dntmnd
For ODIN Flashing Tool:
http://www.downloads.techdiscussion.in/software/download-odin-rooting-software/
and Procedure to Flash is:
- Shutdown Galaxy Fit and restart it in Recovery Mode. For that hold the volume down key + Home key and power key. Hold it for some seconds and leave it. The device will boot in recovery mode. When the yellow triangle, connect cell phone and a computer with a USB cable.
- Launch ODIN on your system. In that look under ID:COM section. The section will turn to yellow once the device is connected and detected.
- Now click on OPS. It will ask you to browse the downloaded firmware package. Browse to GIO_1.0.ops. Once it is selected click on One Package and choose S5670DDKT3_S5670ODDKT2_S5670DDKT2_HOME.tar.md5.
- Now click on Start. The update process has started and it will take few minutes to complete.
- Once it is done, the device will reboot itself. Later on you can go in Settings and checkout the firmware version.
:good::fingers-crossed:

Plz See Image.

[Q] Bricked With Odin...How do I hard Reset?

Hi! I Rooted my Galaxy Tab 2 3100 with Odin. Because the Memory is SO small I tried to unistall some root programs........I blew it....
Now after the Galaxy Tab 2 logo appears it stays in the SAMSUNG logo for ever. Pressing volume up plus power gets you into Odin with 2 choices
Dowload a Rom....stays for Hours downloading and nothing happens
Cancel and reset......back to the same story......
Is there a way of hard resetting?
The rooting I did after I upgardaed to 4.2.2 android version.
HELP ME!! I promess not to fool arround with ROOT programs anymore!!!! Jajajajaja!

Simple - you have download mode, then use it. You know how to use Odin on PC?

Yeah "download" means you hook it up to your computer and send the stock image over Odin. It doesn't download from the Internet or anything like that.
Sent from my Nexus 4 using XDA Premium HD app

Ok....
shakatu said:
Yeah "download" means you hook it up to your computer and send the stock image over Odin. It doesn't download from the Internet or anything like that.
Sent from my Nexus 4 using XDA Premium HD app
Click to expand...
Click to collapse
Thanks a lot! I´m not very good at this, as you can tell..........
Questions:
How do I get it into the "comunication mode" with Odin, where do I download the stock image, and how do I install the image in the tablet.
Thanks again!!

Ok........
luxpiotr said:
Simple - you have download mode, then use it. You know how to use Odin on PC?
Click to expand...
Click to collapse
Hi! Thanks for your answer! Could you tel me how to get it in Download mode, and how to use Odin to repair it? Thanks!

Corto2809 said:
Hi! Thanks for your answer! Could you tel me how to get it in Download mode, and how to use Odin to repair it? Thanks!
Click to expand...
Click to collapse
- Go to sammobile.com and download the latest Stock firmware available for your region.
- On the page where you download the firmware there's also a link to ODIN.
- If the USB drivers aren't already installed just download the "Samsung USB Drivers" (Google's your friend) or install Kies (though when attempting to flash with ODIN _NONE_ of Kies' background processes must run!).
- Unpack the ODIN ZIP archive, right-click the EXE file -> "Run as Administrator"
- Once you're in ODIN click the "PDA" and select the .tar.md5 of the firmware you downloaded
- TURN OFF THE TABLET and DISCONNECT from the charger/USB
- Press and hold POWER + VOL UP
- On the screen that will now show up select "Download Mode"
- Connect the tablet and wait for a second (in case Windows wants to install some driver first)
- Flash
- Disconnect once the tablet restarts and let it do its thing

Thank You!!!
BoneWithABeagle said:
- Go to sammobile.com and download the latest Stock firmware available for your region.
- On the page where you download the firmware there's also a link to ODIN.
- If the USB drivers aren't already installed just download the "Samsung USB Drivers" (Google's your friend) or install Kies (though when attempting to flash with ODIN _NONE_ of Kies' background processes must run!).
- Unpack the ODIN ZIP archive, right-click the EXE file -> "Run as Administrator"
- Once you're in ODIN click the "PDA" and select the .tar.md5 of the firmware you downloaded
- TURN OFF THE TABLET and DISCONNECT from the charger/USB
- Press and hold POWER + VOL UP
- On the screen that will now show up select "Download Mode"
- Connect the tablet and wait for a second (in case Windows wants to install some driver first)
- Flash
- Disconnect once the tablet restarts and let it do its thing
Click to expand...
Click to collapse
Thank you very much!! You saved my life!! Tab2 is running agin!!!

[ROOT] Samsung Galaxy Tab E - T561

Hey guys,
After long search for root for my Tab E - T561, i was able to root my tab with kingoroot pc application. so long story short, i am uploading tar file which will root T561 on kitkat 4.4.4.
How to:
1. Download the attachment
2. Extract it using 7zip or winrar.
3. Download latest Odin 3.10.7 (Google it)
4. Reboot your Tab to Download mode by holding home button, volume down button and power button at the same time.
5. Click AP and choose extracted tar file and Press start.
6. Voila! Rooted Tab E - T561
7. Press Thanks
need any help, PM me

hey tried this but flash failed. now i am stuck at boot logo
imfaraz said:
Hey guys,
After long search for root for my Tab E - T561, i was able to root my tab with kingoroot pc application. so long story short, i am uploading tar file which will root T561 on kitkat 4.4.4.
How to:
1. Download the attachment
2. Extract it using 7zip or winrar.
3. Download latest Odin 3.10.7 (Google it)
4. Reboot your Tab to Download mode by holding home button, volume down button and power button at the same time.
5. Click AP and choose extracted tar file and Press start.
6. Voila! Rooted Tab E - T561
7. Press Thanks
need any help, PM me
Click to expand...
Click to collapse

Any update?
Sent from my SM-T560NU using XDA Free mobile app

sammymcalaxy said:
Any update?
Sent from my SM-T560NU using XDA Free mobile app
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=3300291

Sorry for being so late!
lijoc said:
hey tried this but flash failed. now i am stuck at boot logo
Click to expand...
Click to collapse
What Model do you have there buddy?

- Install Kies3 from samsung.
- It will not recognize the device .... no panic!!!
- Open in menu Tools->Update and initialize firmware
* put the model number and serial number you have in the back of the tablet...
- It will download the proper original firmware from the samsung site and once done push on restore

sm-t561
Not work. F A I L !

bejinaru said:
Not work. F A I L !
Click to expand...
Click to collapse
Do it the proper way!
http://forum.xda-developers.com/showthread.php?t=3302935

How do I do it with out PC

I have the T561M Tablet.
Is there a ROM for android 6 or 7 for the T561M ??? At where???
Because I have ROOT and RECOVERY, but ROM is missing.
sammymcalaxy said:
Any update?
Sent from my SM-T560NU using XDA Free mobile app
Click to expand...
Click to collapse

lijoc said:
hey tried this but flash failed. now i am stuck at boot logo
Click to expand...
Click to collapse
hi. im suffering the same problem after rooting. stuck at boot logo. have you found a way to fix it?

no root t561m
My T561m is with the December 2016 security update and I was not able to do root. Has anything changed? Any suggestion?

ciqvillanueva said:
hi. im suffering the same problem after rooting. stuck at boot logo. have you found a way to fix it?
Click to expand...
Click to collapse
*this way worked for my soft bricked SM-t561 Galaxy tab E. and I hope it'll work for you'll too. after this process all the data from your device will be gone as if it was bought new. Pls make sure you charged your device so that it won't shutdown during the process.
Make sure you have installed samsung USB drives latest version before doing this. If not download it from this link. -----> https://droiddocket.com/download/samsung-usb-drivers-v1-7-23-0/
1.type your model number and search google for flashable firmware for your device. Download it, and unzip it.
2.Download Odin latest version, unzip it and double click Odin3_v3.14.4 file .
3.then you'll get a notification probably, click ok. After that you'll get like this, after that take your soft bricked phone and click power button + volume up /down + home button then
your phone will look like this,
after that connect your device to the computer, on your computer you'll see this.
then click "AP" and select the unzipped firmware you downloaded and click enter.
after that click start and it will start flashing you'll see the progress from your device and from your pc. It will take a while so DON'T un plug the device. after it's done you'll see this in your pc then unplug your device and then it's done.
Don't mind my gramatical mistakes. I hope this helped you.

Lunaworks2007427 said:
*this way worked for my soft bricked SM-t561 Galaxy tab E. and I hope it'll work for you'll too. after this process all the data from your device will be gone as if it was bought new. Pls make sure you charged your device so that it won't shutdown during the process.
Make sure you have installed samsung USB drives latest version before doing this. If not download it from this link. -----> https://droiddocket.com/download/samsung-usb-drivers-v1-7-23-0/
1.type your model number and search google for flashable firmware for your device. Download it, and unzip it.
2.Download Odin latest version, unzip it and double click Odin3_v3.14.4 file .
View attachment 5244307
3.then you'll get a notification probably, click ok. After that you'll get like this, after that take your soft bricked phone and click power button + volume up /down + home button then
your phone will look like this,View attachment 5244319
after that connect your device to the computer, on your computer you'll see this.
View attachment 5244321
then click "AP" and select the unzipped firmware you downloaded and click enter.
View attachment 5244311
after that click start and it will start flashing you'll see the progress from your device and from your pc. It will take a while so DON'T un plug the device. after it's done you'll see this in your pc then unplug your device and then it's done.View attachment 5244329
Don't mind my gramatical mistakes. I hope this helped you.
Click to expand...
Click to collapse
Unfortunately it did not work with rooting, did it as described above.
After the reboot, the tablet hangs at the start screen and does not boot any further.
how can I undo this, because before the device ran without problems

Hello everyone. I need help here.
I have a Samsung SM-T561 & some months ago, I upgraded to version 7.1
Then a few days ago, I wanted to upgrade it to version 10.
That's where things got messed up!
1st. I didn't make a backup of what current ROM.
2nd. I completely forgot to enable USB debugging (again, despite It wasn't the first time I used custom ROM)
3rd. The problem must have been from the ROMS I installed. They didn't work. So I factory resetted EVERYTHING. EVERYTHING. INCLUDING THE SYSTEM.
So basically, I HAD TWRP. I HAD NO OS. I DIDNT TURN ON USB DEBUGGING MODE.
Then I understood that I didn't need ODIN anymore because I had TWRP.
So.
I downloaded the files to flash again. On SD card. And inputted it inside . So it still DIDNT WORK!!
Then I flashed in IMAGE form.
Then my TWRP DISAPPEARED.
IM ON CONSTANT BOOTLOOP.
THE ONLY THING I CAN ACCESS IS THE DOWNLOAD MODE.
AND I CAN NOT CONNECT WITH ODIN BECAUSE I HAVENT TURNED ON USB debugging...
Someone should kindly... please. Get back to me

Samsung Galaxy S Duos S7562L Baseband Modem S7562LVJALK2 S7562LUUBALK3

I needed to make the change of this phone baseband S7562XXLJ3 to S7562LVJALK2 S7562LUUBALK3 compatible with Colombia, Brazil, Panama, Uruguay, Trinidad and Tobago, drew from the official version for this phone baseband and want to share this with you.
Instructions:
0. Installs in download mode. Turn off and then turn on the phone while pressing the keys Volume down + Menu Key and + Power then when dowload start mode press Volume Up
1. Unzip the downloaded file baseband * .bin
2. Connect to usb our phone the computer and open Odin verifying that the phone is recognized by Odin.
3. Select [PC] in Odin 3.10.XX or [PHONE] in Odin 3.07 or less. Search and select the file S7562LVJALK2_fat.bin
4. Leave selected Auto Reboot and F. Reset Time
5. Start.
6. Odin restart our phone and verify About our device in the new version of baseband appears now as S7562LVJALK2
7. That's it. I hope you serve as my served me. Enjoy
Download link
https://goo.gl/ccVLPd

necessary permission
Hey man , I need a lot of this file . However it is necessary permission for download.

oliveiranetto said:
Hey man , I need a lot of this file . However it is necessary permission for download.
Click to expand...
Click to collapse
OK. Try Again
Please Confirm

Thank you. I followed your tutorial, but still did not change the baseband from my device .

oliveiranetto said:
Thank you. I followed your tutorial, but still did not change the baseband from my device .
Click to expand...
Click to collapse
it odd that do not work
try removing the selection of auto reboot time and F.Reset
manually restart
if it does not work the first time, try again 3 times. Sometimes usually it works
the other steps do not change

does this work on CM kit kat? do you have working wifi?

keikun007 said:
does this work on CM kit kat? do you have working wifi?
Click to expand...
Click to collapse
yes it does, the baseband operating normally and my wifi too

Samsung s6 brick, S/N number

Hi, this is my first post on this forum. Thanks for helping me. I apologize if my english isnt the best.
I have this model: SM-G925W8. but im stuck in the blue screen that said that i have to use smartswitch to fix it. But in smartswitch, i need the S/N, and i dont have the box and my phone dont have it in the back. What can i do? Thanks for answers :good:

ItsAj said:
Hi, this is my first post on this forum. Thanks for helping me. I apologize if my english isnt the best.
I have this model: SM-G925W8. but im stuck in the blue screen that said that i have to use smartswitch to fix it. But in smartswitch, i need the S/N, and i dont have the box and my phone dont have it in the back. What can i do? Thanks for answers :good:
Click to expand...
Click to collapse
- Unzip SamFirm
- Copy all SamFirm's file in a new folder
- Launch SamFirm.exe
- Write the parameters like in the "picture 1"
- Unzip the the file SM-G925W8_1_20170825144427_9dzo3tq8md_fac.zip.enc4
- Install Odin and put the phone in downloading mode
- Put the file accordingly in Odin
- Flash

dinamo1975 said:
- Unzip SamFirm
- Copy all SamFirm's file in a new folder
- Launch SamFirm.exe
- Write the parameters like in the "picture 1"
- Unzip the the file SM-G925W8_1_20170825144427_9dzo3tq8md_fac.zip.enc4
- Install Odin and put the phone in downloading mode
- Put the file accordingly in Odin
- Flash
Click to expand...
Click to collapse
How i put the file "accordingly" in Odin? Do you have an example? Thanks
And what happen if something goes wrong? Like if odin tell me it falied?

ItsAj said:
Hi, this is my first post on this forum. Thanks for helping me. I apologize if my english isnt the best.
I have this model: SM-G925W8. but im stuck in the blue screen that said that i have to use smartswitch to fix it. But in smartswitch, i need the S/N, and i dont have the box and my phone dont have it in the back. What can i do? Thanks for answers :good:
Click to expand...
Click to collapse
You have to reinstall the correct firmware for your device.
Flashing Guide:
first download a correct firmware for model of your device(Go to setting>About phone>Model Number(it starts with SM) from www.updato.com or www.sammobile.com and then put it on you computer. then download ODIN PC version.
after downloading them charge your device over 60 percent and then conncect it to the pc.
then power off your device and hold Volume down + Home button + Power button together after that a page will be shown then Press Volume + to Confirm.
Run Odin and unzip the firmware that you have downloaded it(the file extension is .Tar) then click on AP on ODIN and select the firmware file wait for few minutes to file is being read.
Make sure that Auto Reboot is selected and Re-partiation is deselected then start the flashing after that you will get a message(Done with Green Color)
to asure your device has been inserted to ODIN the top of Odin color will be changed to Blue.
Be careful,Odin its a powerful software and if you dont know about flashing dont use it. It may cause to your device to be instable/.