Related
Okay...so let's say that I wanted to hypothetically tighten up the sliding mechanism, and let's say that hypothetically I got to where all screws (yes...including the VOID sticker one is not supposed to tear/alter/drive a screw driver through) w re removed--got to the part where the back case starts to come off but gave up at trying to pry it off at the end w/ the usb/soft reset point (hypothetically).
DIDN'T TOUCH ANYTHING ELSE
Put the screws back in, sim and microSD cards back, turned on phone---and now I get 1/2 cell signal reception outdoors and the !!! indoors...
I know the warranty is out the door...but what did this devilishly curious semi genius that shall remain nameless touch that would have affected the phone in such manner??
Gps and wifi still work fine...it's just that the phone's lost 1/2 of its cellular signal!!
hypothetically...
I dunno what the hypothetical person did, but that is actually quite amusing (Hypothetically speaking of course)
My dear anonymously oversized tramp stamp tattooed fellow senior member...
Your reply was of no help whatsoever--
But, seeing as you are in need of some funds, I will say that I will NOT contribute to your marriage fund...
Instead, I will be more than happy to support your future alimony fund.
But no, seriously, no clue...huh?
maybe the hypothetical person "touched" the cell antenna with his screwdriver?
That is hilarious. If it ain't broke, DON'T FIX IT! Jeez why can't people learn this? I learned this when I was 5.
Hypothetically speaking, you can sell this phone on ebay for parts and call the insurance company and say you lost it *cough* hypothetically speaking.
try opening it up again and wiggling the antenna to see if it gets better? - hypothetically speaking of course
yep, maybe the antenna was net set back in place correctly. also touching the antenna with anything metallic/conductive wouldn't cause any problems IF there was no power supplied to it, different story if the device was on.
you might want to check out Mike Channon's website and download the At&t Fuze service (disassembly) manual.
DJGonzo said:
That is hilarious. If it ain't broke, DON'T FIX IT! Jeez why can't people learn this? I learned this when I was 5.
Hypothetically speaking, you can sell this phone on ebay for parts and call the insurance company and say you lost it *cough* hypothetically speaking.
Click to expand...
Click to collapse
It would be all good except for the fact that the sliding mech. is loosening up that there is a 2mm gap between the keyboard and the screen when closed.
I'm sure I'm not the only one sounding like a Spanish Flamenco dancer with those shells in her hands..
Clikity clack
Clikity clack
clack clack clack
Why wouldn't one want to hypothetically fix this?
Does anyone think buying the antenna would solve anything?
your not the only one with that problem of the clickety clack clickety clack clack clack issue!
buying the antenna wont solve anything
this hypothetical semi genius needs to go back into the phone, and following the service manual which can be found by googling for it put the handset back together
chances are you either forgot to reattach something or you attached it incorrectly
make sure all the black 'tapes' on the back of the handset are secure also
duke_stix said:
chances are you either forgot to reattach something or you attached it incorrectly
Click to expand...
Click to collapse
Ahem, thank you my good man...I'll uhh...let HIM know
Maybe you touched the attenna in the no no place.. you dirty man you.
Hardy Hardy Harr....
I'm am hybopthetically laughing something off right now...
The first time I tried removing the back cover...I got nowhere near removing it...I gave up trying to get it to come off the bottom end of the phone (with the usb input)--so I don't think I came close to touching the antenna...
I managed to remove the casing earlier today, unplugged the antenna, plugged it back in to secure its connection...same problem....
Wow...all 233 of you are very quiet...
please tell me this semi genius, hypothetical person used the service manual which exists? it would be good of you to let HIM know that the service manual will provide him with a foolproof way of ensuring the handset goes back together as HTC intended.
Particularly if this semi genius 'tried removing the back cover...[he] got nowhere near removing it'!
http://www.mikechannon.net/page1.html
tell that semi genius to head over to that site, download the raphael service manual and become a fully fledged genius!
I know how it SHOULD work, but it seems it takes much too much effort to put the US-plug attachment into the charger... I put it on and slide it like 80% of the way and it gets stuck and even with a lot of force it won't go in. I don't want to break my charger, what should I do?
Has anyone else experienced this?
I was a bit worried about the amount of force required myself, but it did connect without breaking anything for me. Just keep pushing!
Had exactly the same problem with my UK plug here and I actually managed to bend the little T shaped part on the damn plug!!! It still wouldn't go in so got a small flat metal file and gently filed the T shape so it made it slightly smaller and then it clipped together. Seems the notch that receives the T shape is a little too small so had to do some DIY lol.
bedoig said:
I was a bit worried about the amount of force required myself, but it did connect without breaking anything for me. Just keep pushing!
Click to expand...
Click to collapse
Ok I did and it was violent, but it worked.
doronster195 said:
Ok I did and it was violent, but it worked.
Click to expand...
Click to collapse
I was a bit worried about something breaking, but I had to employ some violence as well. I suspect the attachment may never be removable again.
Lani Kai said:
I was a bit worried about something breaking, but I had to employ some violence as well. I suspect the attachment may never be removable again.
Click to expand...
Click to collapse
I think thats how it was made, since the plugs flip up to hide.
Yeah... it took an INSANE amount of force to snap it in.
I, too, was seriously worried of breaking it, but in the end it clicked together... and I'm sure I will never ever take it apart
Lani Kai said:
I was a bit worried about something breaking, but I had to employ some violence as well. I suspect the attachment may never be removable again.
Click to expand...
Click to collapse
It is removable, trust me, but you have to push at the point it says 'push' on the plug! I missed this at first and spent a good few minutes of tugging, scared I'd break the thing!
Is everyone else's power button on the ATT HOX feel like it's hard to push? Maybe not hard to push but it's such a low profile that I feel that I am having problems pushing it... Hard to explain. Just making sure there isn't something wrong with the phone that I have. Just took back a case to Best buy because the power button was soooo hard to push in it. Sometimes didn't register.
Thanks all
AJ
Not just you. I'm having a hard time getting used to it from my old Captivate. (Of course it's about 12 times better in every other category, so I'm not too upset!)
Oh I'm not upset.....I'm coming from a Samsung Galaxy S2 and this phone is by far the best phone I've ever used so far but since every phone I've ever used has had a raised power button be it on the side or top, I was just worried that maybe I got a defect but I guess I didn't.
That's why I love this board. So friendly and polite. Thank you.
AJ
Hmm... Was your case the platinum holster one? That's what I'm using right now and It's kinda ridiculous how hard it is to press. It registers maybe 25% of the time I press it. I use my nail now though so it works every time almost.
Sent from my HTC One X
LOL! Yep sure was. Took it back to Best Buy and the returns lady said that this was the third one she had seen today returned! I just want a simple silicone case with good protection and camera lip thing. Is there anything like that out there for the ATT HOX?
Thanks all
AJ
Hehe, thought it might be the same one. I noticed the packaging to my case was actually opened when I bought it. Someone might have returned it Sunday morning xD.
Not really sure what other cases are available that fit correctly. I recommend not getting one on eBay. Most block the camera. There's a thread about cases and pouches in the accessories section.
Sent from my HTC One X
I just actually picked up that case today! I'm going to return it as well because I too am having a difficult time pressing it. Also, the fourth row of the speaker grill was also being covered. Pretty poor design.
Sent from my HTC One X using XDA
I got a rocketfish gel/silicone semitransparent grey case at best buy for $25...it is light, fits snug and doesn't cover the speaker..covers the back well so that when you sit it down, the camera lens is in no danger of being scratched as the camera protrudes a little bit without case...I have same issue w power button but it's not hard to press...it's that it's so low profile that its hard to feel it...fantastic phone and battery is amazing...got 26 hrs out of first charge...got about 9 on my Vivid...but it was a 1600 mah battery where this one is 1800 or 1850, not sure though..and phone is about 1.5 ounces lighter..battery is better because it is embedded...you lose power anytime you 'plug" in a battery where the contacts are...this battery is directly on the board so there is no loss...same principle applies to hard wired appliances compared to those with plugs...coax cables with multiple splitters result in signal degradation on tvs...I think this is why HTC opted for embedded batteries as people complained about battery life...although my various iPhones in the past had poor battery life...but it is best to charge phone ONLY when battery is down to 10% or less...every time u charge, you lose approximately 30-45 seconds of total battery per charge so the less you charge the better...
Sent from my HTC One X using xda premium
Seriously? Do you really think your great batterylife is due to it being "embedded"(which it really isnt) and not having contacts(still has a connector)? Really?
Do you really think you lose 30seconds off your battery life by charging it before it is run down?
Ponderous.
Really erroneous info guy. Not helping. Did you just decide to make things up?
Battery life is better because of improvements with hardware. It uses less juice. PERIOD.
Lithium ion is extremely tolerant of charging from any level. Should have no adverse effect if you charge at any time, full, empty or in between.
Sent from my Desire HD using XDA
LOL. Who cares. Good phone. End of story
YES, what I said is correct and not eronious as you said...been in electronics business for 30 years..I could go into greater detail but it would be over your infant understanding of how electronics work...of course the hardware helps bit that's just part of it..I was programming computers when the IBM 8088 chip came out as well as a wide range of electronic devices...I'm not trying to blow my own horn but I do know what I'm talking about...you should do your due diligence before you try and bash someone...and people wonder why many people left XDA who were a big help...I've never posted ROMs for this reason...I was thinking about it, but people like you just confirm my reservations..amateur...
Sent from my HTC One X using xda premium
austin4913 said:
YES, what I said is correct and not eronious as you said...been in electronics business for 30 years..I could go into greater detail but it would be over your infant understanding of how electronics work...of course the hardware helps bit that's just part of it..I was programming computers when the IBM 8088 chip came out as well as a wide range of electronic devices...I'm not trying to blow my own horn but I do know what I'm talking about...you should do your due diligence before you try and bash someone...and people wonder why many people left XDA who were a big help...I've never posted ROMs for this reason...I was thinking about it, but people like you just confirm my reservations..amateur...
Sent from my HTC One X using xda premium
Click to expand...
Click to collapse
Wooooo calm down. Just cite some sources
stnguyen09 said:
Wooooo calm down. Just cite some sources
Click to expand...
Click to collapse
He doesn't have any, at least not anything recent and reinvent. It's all just tacit knowledge. Amirite?
(This is just my fun way of getting you to give us a source)
Sent from my HTC One X
I love how my thread was hijacked lol.
mine is hard to push with the black&white speck case. but without a case its easy to push...
austin4913 said:
YES, what I said is correct and not eronious as you said...been in electronics business for 30 years..I could go into greater detail but it would be over your infant understanding of how electronics work...of course the hardware helps bit that's just part of it..I was programming computers when the IBM 8088 chip came out as well as a wide range of electronic devices...I'm not trying to blow my own horn but I do know what I'm talking about...you should do your due diligence before you try and bash someone...and people wonder why many people left XDA who were a big help...I've never posted ROMs for this reason...I was thinking about it, but people like you just confirm my reservations..amateur...
Sent from my HTC One X using xda premium
Click to expand...
Click to collapse
Was your 8088 hardwired to your A/C at home so it was more efficient? Programming != electrical engineering.
Yes there is a TINY bit of loss by using contacts. It's an easy check with an ohmmeter. But it really only applies to high current applications, which we are not dealing with here. And no, it's not enough to make any measurable difference. And your coax analogy is ridiculous. We aren't dealing with gain, SNR, taps, etc. Geez.
Going back on topic, I now get 95% registers with the power button. If you press on the far left of the button it works almost every time with the platinum case. I think it just needed to be broken in.
Sent from my HTC One X
Same here, but mine is worst cause this case that I have, has a hard rubber button
Ok austinguy, you really don't get it. I design, install and deploy:corporate networks, infrastructure(copper, coax, fiber), telephone systems(voip, copper, t1), install electrical systems, CCTV(dvr, network), wireless solutions(point to point, mesh, custom antennas), satellite, etc, etc. I have many years of learned and hands on first hand experience with the software, hardware, and real world implementation.
I stand by the facts.
Sent from my Desire HD using XDA
borismanalo said:
Same here, but mine is worst cause this case that I have, has a hard rubber button
Click to expand...
Click to collapse
Mine is hard rubber too. Which case did you buy?
c5satellite2 said:
Ok austinguy, you really don't get it. I design, install and deploy:corporate networks, infrastructure(copper, coax, fiber), telephone systems(voip, copper, t1), install electrical systems, CCTV(dvr, network), wireless solutions(point to point, mesh, custom antennas), satellite, etc, etc. I have many years of learned and hands on first hand experience with the software, hardware, and real world implementation.
I stand by the facts.
Click to expand...
Click to collapse
Sounds a lot like what I do. What's your point? Doesn't Make you an expert in lithium-ion batteries now does it? Well... I guess the high-grade UPS systems we work with could, but you didn't list that or just don't work with them.
Sent from my HTC One X
I've been playing around the service menu and tested the Pressure Sensor. In a solid waterproof phone, pressure should remain steady when acted upon by outside forces.
I simply tried to moderately blow some air into the USB port and there's a notable difference. Also removed the sim cap and sucked on the port. Air was clearly passing through.
I'm curious if it's just my phone with this issue in which case I'll replace it, or if it's a design fault, in which case you shouldn't submerge it.
In the screenshots you'll see the pressure difference. So please test this by accessing the service menu *#*#service#*#*, > tests > pressure sensor and simply blow some air into it.
And for the giggles and ranting, there's the sony talk thread https://talk.sonymobile.com/t5/Xper...s-waterproof/m-p/1237116/highlight/true#M2652
Sebi673 said:
I've been playing around the service menu and tested the Pressure Sensor. In a solid waterproof phone, pressure should remain steady when acted upon by outside forces.
I simply tried moderately blowing some air into the USB port and there's a notable difference. Also removed the sim cap and sucked on the port. Air was clearly passing through.
I'm curious if it's just my phone with this issue in which case I'll replace it, or if it's a design fault, in which case you shouldn't submerge it.
In the screenshots you'll see the presiune difference. So please test this by accessing the service menu *#*#service#*#*, > tests > pressure sensor and simply blow some air into it.
Click to expand...
Click to collapse
In Xperia Z3 there was a hole in the lower-left corner that if not covered by hand also let the pressure to drop down.
I think that every phone has to have some kind of a "blow off valve" to prevent internal pressure from rising when the phone heats up to avoid damaging the seals around the screen and the back.
Note that when you cover the usb port pressure stays perfectly stable. The phone is still waterproof it just lets the internals "breathe"
mracer164 said:
In Xperia Z3 there was a hole in the lower-left corner that if not covered by hand also let the pressure to drop down.
I think that every phone has to have some kind of a "blow off valve" to prevent internal pressure from rising when the phone heats up to avoid damaging the seals around the screen and the back.
Note that when you cover the usb port pressure stays perfectly stable. The phone is still waterproof it just lets the internals "breathe"
Click to expand...
Click to collapse
It's far more than a simple valve. For example if you have water in the port and you blow some air to take it out, that water will actually go inside the phone. I'm asking because if ever submerged, water pressure will be far grater than my air blowing capabilities ))) so things can get messy pretty fast.
It's far too easy to change the pressure inside it, so all I need to know is if other XZp are behaving the same way or if it's just mine.
Sebi673 said:
It's far more than a simple valve. For example if you have water in the port and you blow some air to take it out, that water will actually go inside the phone. I'm asking because if ever submerged, water pressure will be far grater than my air blowing capabilities ))) so things can get messy pretty fast.
It's far too easy to change the pressure inside it, so all I need to know is if other XZp are behaving the same way or if it's just mine.
Click to expand...
Click to collapse
As I said Z3 behaved similarly and I have submerged this phone a couple of times and never had any problems with it. Note that air particles are much more able to squeeze through tight spaces than water.
Same principle aplies to waterproof jackets, they let the air pass through so that you wont get sweaty while at the same time the won't let water go through.
mracer164 said:
As I said Z3 behaved similarly and I have submerged this phone a couple of times and never had any problems with it. Note that air particles are much more able to squeeze through tight spaces than water.
Same principle aplies to waterproof jackets, they let the air pass through so that you wont get sweaty while at the same time the won't let water go through.
Click to expand...
Click to collapse
Yes man, I know what a valve is and how it operates in a phone. I've been having xperias for over 5 years. I'm not on Talk.sonymobile, I'm on xda. So if you can try the test whenever you can. All it takes is 1 minute.
I opened this thread because I need to see if mine has those rubber seals too loose or if it's a general and normal thing. I asked for xzp owners to try the test because on my phone air passes virtually unobstructed.
Sebi673 said:
Yes man, I know what a valve is and how it operates in a phone. I've been having xperias for over 5 years. I'm not on Talk.sonymobile, I'm on xda. So if you can try the test whenever you can. All it takes is 1 minute.
I opened this thread because I need to see if mine has those rubber seals too loose or if it's a general and normal thing. I asked for xzp owners to try the test because on my phone air passes virtually unobstructed.
Click to expand...
Click to collapse
It works for me exactly the same way as you described. Sorry I didn't mean to patronise you in any way
There is a pressure regulation in every phone. The reason is the battery, in case the battery is defective (see Shamesung Note ), it will produce gas. This gas can later inflame, hence it is important to get it out of the device.
Illux said:
There is a pressure regulation in every phone. The reason is the battery, in case the battery is defective (see Shamesung Note ), it will produce gas. This gas can later inflame, hence it is important to get it out of the device.
Click to expand...
Click to collapse
I know, I just spent a lot of money on this thing and I'd rather avoid damaging it. In my opinion that valve is way too lose.
Check this video out, I do not agree with this idiotic test but in the end the phone got water damaged. Vibrator Motor is right next to the USB port which in this video it keeps on vibrating even after device is off.
https://youtu.be/Z3JUGkXXXJw?t=17m52s
I might be a bit paranoid but submerging this phone is not a good idea. Maybe something like this will help https://images-na.ssl-images-amazon.com/images/I/91LUJPpD45L._SL1500_.jpg
mracer164 said:
It works for me exactly the same way as you described. Sorry I didn't mean to patronise you in any way
Click to expand...
Click to collapse
I know, I'm sorry for jumping the gun. Didn't get a full night sleep.
I'm weary because I had Xperia XZ for a week, did the same test but the breathability on the usb port was minimum. Anyway, I'll be careful. My (very) old Xperia Z got water damaged in the pool due to a worn rubber band on the headphone jack. Damage was extensive.
Sebi673 said:
I know, I just spent a lot of money on this thing and I'd rather avoid damaging it. In my opinion that valve is way too lose.
Check this video out, I do not agree with this idiotic test but in the end the phone got water damaged. Vibrator Motor is right next to the USB port which in this video it keeps on vibrating even after device is off.
https://youtu.be/Z3JUGkXXXJw?t=17m52s
I might be a bit paranoid but submerging this phone is not a good idea. Maybe something like this will help https://images-na.ssl-images-amazon.com/images/I/91LUJPpD45L._SL1500_.jpg
Click to expand...
Click to collapse
If damaged by submerging, I'd send it on for guarantee and request a new one. It states IP68 proof, that means 30 minutens fully submerged.
Oh and btw, the guy actually FROZE his phone for 12 hours .
Illux said:
If damaged by submerging, I'd send it on for guarantee and request a new one. It states IP68 proof, that means 30 minutens fully submerged.
Oh and btw, the guy actually FROZE his phone for 12 hours .
Click to expand...
Click to collapse
I know.... It's an idiotic test. But leaving that aside, it is compared to another waterproof phone which worked as good as new afterwards. So it's safe too assume that the USB might be letting in a bit more than just data and power.
It's a bit of a letdown, I'll wait for the teardown videos to see if they finally coated the motherboard and other boards against water ingress. Just like you see in the iphone and samsung.
Sebi673 said:
I know.... It's an idiotic test. But leaving that aside, it is compared to another waterproof phone which worked as good as new afterwards. So it's safe too assume that the USB might be letting in a bit more than just data and power.
It's a bit of a letdown, I'll wait for the teardown videos to see if they finally coated the motherboard and other boards against water ingress. Just like you see in the iphone and samsung.
Click to expand...
Click to collapse
Well, I'm the kinda guy who tries out things if promised . What I can tell you, my phone spent a fair amount of time submerged already, I always wanted to try out underwater video recording. No real sense in it, but it's fun .
Still working and it's drying real quick.
Illux said:
Well, I'm the kinda guy who tries out things if promised . What I can tell you, my phone spent a fair amount of time submerged already, I always wanted to try out underwater video recording. No real sense in it, but it's fun .
Still working and it's drying real quick.
Click to expand...
Click to collapse
I know it's fun, it's even more so when you wash it in the sink in front of people haha. Can you please do me a solid and test the pressure sensor while blowing air into the usb? like I tried - 2 cm away, full lung pressure on the usb, and tell me if that pressure rapidly moves up. It will help me sleep better at night after I wash the thing haha.
Sebi673 said:
I know it's fun, it's even more so when you wash it in the sink in front of people haha. Can you please do me a solid and test the pressure sensor while blowing air into the usb? like I tried - 2 cm away, full lung pressure on the usb, and tell me if that pressure rapidly moves up. It will help me sleep better at night after I wash the thing haha.
Click to expand...
Click to collapse
I'll do so in 13 minutes, im currently running a battery test. Just as side note, Amazon Underground seems to drain battery like hell on 7.1.
---------- Post added at 01:46 PM ---------- Previous post was at 01:23 PM ----------
Sebi673 said:
I know it's fun, it's even more so when you wash it in the sink in front of people haha. Can you please do me a solid and test the pressure sensor while blowing air into the usb? like I tried - 2 cm away, full lung pressure on the usb, and tell me if that pressure rapidly moves up. It will help me sleep better at night after I wash the thing haha.
Click to expand...
Click to collapse
Ok, done. Pressure going up rapidly. Consider it normal.
Illux said:
I'll do so in 13 minutes, im currently running a battery test. Just as side note, Amazon Underground seems to drain battery like hell on 7.1.
---------- Post added at 01:46 PM ---------- Previous post was at 01:23 PM ----------
Ok, done. Pressure going up rapidly. Consider it normal.
Click to expand...
Click to collapse
YAY!!!! Paranoid Parrot now returning to its cage :victory:
Mine does the same
I have the same problem and my xzp had water damaged,they changed me a new one which still have this problem....I will not try twice.Maybe this is a manufacturing problem.
sonyisall said:
I have the same problem and my xzp had water damaged,they changed me a new one which still have this problem....I will not try twice.Maybe this is a manufacturing problem.
Click to expand...
Click to collapse
It's a design flaw then..... I'll buy the usb silicon caps just to be extra safe.... Shame they didn't manage to build this properly.....
Forgive me my ignorance. I know it's stupid question and I know answer will be yes, but it's always worth double checking.
So I can submerge xz premium without any usb/jack and other ports covers as they were just designed to be able to handle that?
SUPERSLEDZ said:
Forgive me my ignorance. I know it's stupid question and I know answer will be yes, but it's always worth double checking.
So I can submerge xz premium without any usb/jack and other ports covers as they were just designed to be able to handle that?
Click to expand...
Click to collapse
Yes, that is the idea behind IP68 certification. I dumped my phone in the pool yesterday, just for fun. Just PLEASE make sure to dry the phone before charging it. I know that sounds stupid but there is some photos around of ppl claiming their devices just started burning. Due to the nature of energy transport in USB-C 3.1, that is almost impossible - unless you short-circuit it with water .
Edit: This fan from Digi-Key isn't the same fan as the stock one. I wouldn't advise buying it until bignazpwns confirms if his method works.
The fan in this phone is made of the softest type of plastic available. If you've messed with it at all you've probably broken it accidentally. Or, in my case you dropped the phone and the fan began clicking.
There are no results if you google "red magic 3 fan replacement", but luckily I've found the fan itself (not the fan housing) on Digi-Key for roughly $18.72 (remove the space): www .digikey.com/product-detail/en/delta-electronics/BSB01703HA3-00CAJ/603-2066-ND/7403223
A guide on how to take it out/put it in can be derived from this video (remove the space): www .youtube.com/watch?v=JiS24PRIq-A&t=268s
Helo, thanks for the info. Do you know where this fan ships from which country ?
lius90 said:
Helo, thanks for the info. Do you know where this fan ships from which country ?
Click to expand...
Click to collapse
The sender address is extremely Chinese.
Thank you so much for the info
Info removed.
Info removed
bignazpwns said:
That fan won't work. It's a 4 wire pwm can in the RM3 that fan is a 3 wire.
I ordered one I broke my fan so I'm going to see if it has the -FP+ like the stock fan and just needs a wire or if I gotta transplant the board. Delta said it's a custom fan so I'll post what I get to get it back up and running.
Update. They offer no replacement fans what so ever and no help at all other then send it in for an extremely costly repair that will take over a month to complete.
I'll be making a guide this week about adapting the bsb01703ha3-00 as a replacement. There is no reason for them not to sell this fan or provide any info. 3 wire fan should work but will have no pwm control but I think there might be a solder point on it for the pwm lead. I'll post my findings as well as If I swap out the fans pcb with the OEM one. That should be the best way to do it and use the new fan as a donor housing and fan.
You will need to mod the housing tho since the blade is just held in by it's magnets and could move when dropped. This is why the OEM has that little bar over it. But I'll make a guide for everyone and save them a ton of money and time.
If you have a sla or dlp printer and you need a new housing here ya go.
www .thingiverse.com/search?q=Red+Magic+3&dwh=455dc3648534fa9
I'm working on a replacement fan as well.
Click to expand...
Click to collapse
Sorry I've been meaning to make an update. I had the same idea you had for the -FP+ thing, and was just going to try connecting everything judging from the labels on (remove space) www .delta-fan.com/Download/Spec/BSB01703HA3-00CAJ.pdf , and connect + to + and - to -, and try both remaining ones with the middle wire. Unfortunately my fan's cables were too short to do that.
What I wound up doing was taking the circuit board (with all 4 cables) and very carefully placing it in the housing of the new fan, replacing its board. I soldered everything back up and nothing. It wouldn't spin at all, even on boot. So as far as I know this isn't a viable method, pending bignazpwns' response. I've already updated the OP to reflect. Big ups to bignazpwns for going the extra mile with the replacements
Info removed
Info removed
Info removed
Info removed
Info removed
bignazpwns said:
Note.
Replacement fan is much louder due to the fact 100% is a bit more RPM. Just replaced the fan with one with a replacement blade assembly, coils off the aftermarket fan all on the stock pcb. This gets the auto speed control back and makes preform like stock. 100% is a little bit less in terms of RPM but much more quiet.
Just note swapping coils is not easy.
You will need to remove 1/2 a coil so you can get to the other solder pad. Red Magic fan used SMT coils and the replacement is soldered by hand. You will also need to apply light heat to remove them. They are stuck down with adhesive. I used a hot air reflow station but you really need to watch the heat because you can cause it to uncoil. Scale from 1-10 for soldering skill this is a 10.
The replacement fan drops right in and offeresore rpm to move more air at 100% just connect the 3 wires and be done with it. I'm always here to give advice and help of you need to do this. Also for adhesive I use this. AJ Sign World Best 1" Ultra-Thin... https://www.amazon.com/dp/B01NBJVU04?ref=ppx_pop_mob_ap_share it's thin and super strong. If you work on phones I highly recommend you get a roll.
Click to expand...
Click to collapse
Thanks for the advice just in case my fans breaks when i get my phone
lance9547 said:
Thanks for the advice just in case my fans breaks when i get my phone
Click to expand...
Click to collapse
NP. I destroyed mine with 100psi of air lol. No big deal easy fix and it's only hard if you make it. I'll probably swap the replacement fan back in for the higher rpm and more air flow. On and off control is good enough for me.
What happened with all of these info removed ? My fan started to make weird noises and i start investigating on its replacement... The most disappointing fact is i barely used the fan and the phone has around 6 month :|
So what happened with the info ?
Alex4455 said:
What happened with all of these info removed ? My fan started to make weird noises and i start investigating on its replacement... The most disappointing fact is i barely used the fan and the phone has around 6 month :|
So what happened with the info ?
Click to expand...
Click to collapse
OP trolled us.
No I removed the info. People need to realize no on won here owes people anything. But for some reason they think they do. So all info was removed. People can figure out what needs to be done on there own.
Alex I'll help you out. Just send me a private message.