Hi Guys,
I have little problem with my Desire S. I have recently replaced the digitizer. After fitting it and checking the phone i discovered that top area of touch screen isn't working. So I took it apart again and accidentally broke the LCD. So I ordered LCD and digitizer as one unit from ebay, fitted it.....And LCD is working fine, but new digitizer isn't working properly. I'm pressing bottom half but its registering touch in top half. Also for buttons at the bottom don't work.
So I plugged in old digitizer and it works ok apart from that faulty top area.
I had it sent over to some repair shop and they tested it with LCD/digitizer as one unit with same fault. But my old digitizer works.
Any ideas?
Thanks
Marcin
Related
Hello,
my firend's qtek s200 has this problem.
There is a 1,5 cm circle in the center of the screen where it won't "touch".
I took the phone appart, and even removed the touchscreen layer from the lcd.
I then glued it back on but the problem still exists.
If he buys a lcd+touch screen from ebay, will that be enough? I mean, could it be a problem on the motherboard?
Any help is appreciated
Thanks
Did you check also the flat wire that connects lcd to main board?
User22 said:
Did you check also the flat wire that connects lcd to main board?
Click to expand...
Click to collapse
Yep, it seems to be in a good condition.
I reconnected it, cleaned it etc.
I've same problem.
Have you solvet it?
Thanks
I cracked my screen a few months back, and right after it happened I bought a new digitizer to replace the cracked one. The install didnt go very well, since the tape used to adhere the digitizer to the LCD got mangled during removal of the original digitizer. Dust ended up getting between the LCD and Digitizer etc. One other problem I ran into was that the LED's that are supposed to illuminate the home/menu/back/find buttons were now shinning up into the screen and washing it out.
Anyways I got fed up with the dust and bought a new fully assembled screen/digitizer off ebay. I installed it last night and everything is great except that the lights are still shinning up through the glass and washing out the lower inch of the screen. I dont see why this would happen as there is really only one way to put it all back together.
Any insight as to how to get the lights to stop doing this?
Thanks!
I managed to break the screen on my Optimus 3d last night, not sure if it was dropped or ran over. I found it face down in my driveway this morning and to my horror when I flipped it over the screen was completely smashed, however the phone is still working fine, minus the never ending ghost call issue.
What make the situation worse is Rogers just sent me out a replacement phone yesterday and I have to send this one back, in the next couple days.
So I called a repair centre and they wanted $190 to repair the phone, and stated they would need to replace the LCD and the glass screen. I know there is nothing wrong with the LCD screen, phone functions and all colours are good, just has broken glass.
My question is, can I repair just the glass without replacing the LCD? I have found the screen for around $30 on ebay. Based on watching the how to on youtube it doesn't look like too difficult of a job.
me too i have broke my glass of my phone and they said like your prize to replace thre glass but in my country crunncy and the screen work perfectly I don't know why they want to change the screen too it's annoying
Sent from my LG-P920 using xda app-developers app
n3fta said:
I managed to break the screen on my Optimus 3d last night, not sure if it was dropped or ran over. I found it face down in my driveway this morning and to my horror when I flipped it over the screen was completely smashed, however the phone is still working fine, minus the never ending ghost call issue.
What make the situation worse is Rogers just sent me out a replacement phone yesterday and I have to send this one back, in the next couple days.
So I called a repair centre and they wanted $190 to repair the phone, and stated they would need to replace the LCD and the glass screen. I know there is nothing wrong with the LCD screen, phone functions and all colours are good, just has broken glass.
My question is, can I repair just the glass without replacing the LCD? I have found the screen for around $30 on ebay. Based on watching the how to on youtube it doesn't look like too difficult of a job.
Click to expand...
Click to collapse
If your LCD is working you only need the digitizer replaced (phone front + touch screen) which costs you around 20/30$ http://www.ebay.com/itm/Replacement...080?pt=LH_DefaultDomain_0&hash=item1c2d78e968 .
My touchscreen was broken (randomly pressing things on the screen) and I think the 2nd hand shop I got it from only replaced the digitizer I think based on the small dust I see on my screen.
This only works if your LCD doesn't show blurry or (partially) black (damaged).
Hey all,
Client brought in a TF300T with a cracked digitizer, good LCD, but no touch response. Changed digitizer, everything works but touch. Original digitizer has no "G0_" number on it, but replacement is a G01.
Because the digitizer wasn't working in the first place, would this be a bad digitizer PCB? I've been searching forums for the past hour but haven't found any fixes for this particular scenario. Attached are images of the digitizers.
Thanks!
I changed screen assembly to my boys Honor 8. All went well.
Not so nice job BTW.
I tried that the screen was working but didnt tested the touch. I reassembled it and noticed that the touch is not regonized.
Does somebody have any clue or is the assembly just broken? :crying:
Likely you didn't connect the digitizer, or the digitizer is broken. Touch won't work without digitizer. I don't know how to fix it, you may have to look it up, maybe Ifixit has a guide. You may need to buy another digitizer for Honor 8.
Problem solved. I detached screen again. In bottom of the screen there was digitizer connector. It looked OKAY but I disconnected it and but it back firmly. Touch started to work. Yeah baby ??
Nice. Was I of any help?