Hey all,
Client brought in a TF300T with a cracked digitizer, good LCD, but no touch response. Changed digitizer, everything works but touch. Original digitizer has no "G0_" number on it, but replacement is a G01.
Because the digitizer wasn't working in the first place, would this be a bad digitizer PCB? I've been searching forums for the past hour but haven't found any fixes for this particular scenario. Attached are images of the digitizers.
Thanks!
Related
Hi Guys,
I have little problem with my Desire S. I have recently replaced the digitizer. After fitting it and checking the phone i discovered that top area of touch screen isn't working. So I took it apart again and accidentally broke the LCD. So I ordered LCD and digitizer as one unit from ebay, fitted it.....And LCD is working fine, but new digitizer isn't working properly. I'm pressing bottom half but its registering touch in top half. Also for buttons at the bottom don't work.
So I plugged in old digitizer and it works ok apart from that faulty top area.
I had it sent over to some repair shop and they tested it with LCD/digitizer as one unit with same fault. But my old digitizer works.
Any ideas?
Thanks
Marcin
I've cracked the digitizer over the screen. the LCD is fine - but the digitizer is broken. I have seen numerous posts about the screen, but not just the digitizer.
Not ever sure where to look for this one. I love this thing, rooted and overclocked to 1.4 there's not much out there that can top it.
Good luck.. I haven't found one yet, mine has been cracked for months.
If you find a source, PLEASE let me know?
I am in need of one as well. Did you ever find one?
I recently dropped my TF300 (in the process of jerry-rigging a carrying case for it, might I add) and it happened to shatter the glass and tear some of the ribbon for the digitizer, rendering it completely useless. The LCD beneath is fine, in fact I have already separated the LCD from the digitizer itself.
My question is:
Can I buy a replacement digitizer for the TF200 and install it to my TF300?
They seem to be the same ribbons and i'm sure the dimensions are the same.
The problem is the digitizer for the TF300 is around $150 and just $50 for the TF200.
Dude word of advice only buy the tf300 glass. But replacing it will be a pain but good luck to you
Sent from my HTC Ruby using xda app-developers app
Almost sure,,
Hello hello,
i recently smashed up the same digitizer of my tf300t. There are no videos about opening the thing, so i proceeded and could unplugged the digitizer without any complication. So, after long searching i found ur question and realize that the connector is just the same. I'm almost sure that tf200 should work properly with tf300.
best regards,
Abrhm
Not the same
I'm sure you have probably figured this out by now, since it's been months, but the TF200 and the TF300 digitizers are indeed DIFFERENT.. And the TF300 can be procured pretty easily these days for about $70.00..
So, this is for the benefit of anyone else who happens to stumble across this post.
Also, heed, there has been a significantly high rate of folks, myself included, who have changed the digitizer out only to find that the touch-screen still doesn't work due to some other issue..
Dear All,
I was having a very wonderful time with my desire S untill recently when something went bad with my saga that the right edge of the touchscreen did not respond. After a few days, the left edge stopped responding as well.
I searched XDA and googled for the problem and I came to know that replacing digitizer helps. My LCD is very much fine and I'm hopeful replacing just the digitizer will help. I've ordered one from Amazon and I'll be performing the replacement myself, referring youtube videos.
Could anyone please share their experience on replacement of digitizer or problems similar to me?
Thanks.
I did that a while ago... Though i had a cracked digitizer instead od an unresponsive one... You should be fine with the video guides. Some of the parts (like the camera cover) will put some resistance though. You'll also need to be careful with the screen as it is glued to the frame. If you will, you should be able to reuse it and watch out for the cable
Sent from my Desire S using xda premium
It's a fairly easy procedure and I have done it on a couple of DSs before.
Just do yourself a favour - take it slowly and follow the instructions closely. Especially when it comes to heating the old tape to separate the digitiser and the LCD - if you try to force it off at all you run a very real risk of cracking the LCD as it's a fragile bit of kit.
Hello everyone!
After coming back from a hike I sadly found my digitizer completely shattered, the LCD works fine and the screen is still responsive in some parts.
Did any of you ever do a digitizer only replacement? I know it's possible with some phones, and there are ones who need an LCD+digitizer replacement.
Thank you!
It could be done, but the cost to change digitizer only is close to replacing the whole set.
Not mentioning the huge effort to separate the broken digitizer from the lcd assembly.
I have tried this, and the result compared to the effort is not worth it.