Database Info

[ROM] How To upgrade or Downgrade LG P940 Prada 3

How to Upgrade or Downgrade LG P940 Prada 3
1. Extract “LGFlashTool 1.2” and instal "Setup_LGFlashTool_1.2.45.921.exe"
2.Replace the file LGFlashTool.exe into C:\LG\LGFlashTool
3. Extract and Install “OMAPFlashInstaller-4.10(2).zip”
4.Exract “LGUnitedModemDriver_WHQL_ML_Ver_4.9.7_All_Win7_LG EAll.zip” and Install “LGUnitedMobileDriver_S497CA20_WHQL_ML_Ver_1.0 .exe ” and “LGUnitedMobileDriver_S497MA20_WHQL_ML_Ver_1.0 .exe ”
5. Turn Off phone, Remove your phone’s SIM and SD cards.
6.Press and hold voll up button in LG P940.
7. When u holding “voll up button” connect the USB cable.
8.When computer detects the new hardware (Omap4430) release “voll up button”.
9. Install the Driver.
10.After Driver installation, go to device manager and change the port “LGE CDMA USB SERIAL PORT” to “com41″.
11. Run LGFlashTool.
12.In DLL select file “LGP940_20120217.dll”
13. In S/W select only *.bin file from “LGP940AT-00-V***-EUR-XXX-***-**-***+0_AP”
14.Choice (Check) “USB” and click OK.
15. Click on Port COM settings(COM plug icon) and select "1"
16.Check as on photos. (host photo is deleted continue in step 17)
17. Click start (The Port 1 window should appear READY).
18.Disconnects USB cable and wait 5 seconds.
19. Press and hold voll up button in Lg P940 and connect USB cable.
20.The update process will begin automatically after that release the “vol up”.
21. When the progress bar reaches 100%, Power ON the LG P940. WAIT 5 MINUT is very slow first boot
If get error 80% (error= the program don't read phone because it restart) no problem go to step 22.
22. Reset the phone after first boot
Driver download:
http://csmg.lgmobile.com:9002/swdata/WEBSW/LGP920/AVIVML/20110623_05/OMAPFlashInstaller-4.10(2).zip
http://csmg.lgmobile.com:9002/data/LGUnitedModemDriver_WHQL_ML_Ver_4.9.7_All_Win7_LGEAll.zip
Sw and Fw:
http://www.mediafire.com/grean89
Same procedure (with photo p920)
http://forum.xda-developers.com/showthread.php?t=1244490
Regards
work 100% tanks for testing "adiif1"

FlashInstaller
Not Found
The requested object does not exist on this server. The link you followed is either outdated, inaccurate, or the server has been instructed not to let you have it.

adiif1 said:
FlashInstaller
Not Found
The requested object does not exist on this server. The link you followed is either outdated, inaccurate, or the server has been instructed not to let you have it.
Click to expand...
Click to collapse
ok fixed link

work thanx!!
all work only have 1 error with 80% (reboot) telephone work good

adiif1 said:
work thanx!!
all work only have 1 error with 80% (reboot) telephone work good
Click to expand...
Click to collapse
yes because the sw flash tool is old 1.2 .. new version 1.3 fix but don't work for me get a reset after first startup

Is this error safe?

adiif1 said:
Is this error safe?
Click to expand...
Click to collapse
yes no problem

great job.
may i ask : V20d+0.part1.rar is same as V20d+0.part2?
or need to be combined?

I respect your work.

hi some questions below:
5. Turn Off phone, Remove your phone’s SIM and SD cards.
with battery? if with battery, will enter: S/W Upgrade mode for step 6&7.
8.When computer detects the new hardware (Omap4430) release “voll up button”.
PC don't detects the New hardware (Omap4430), just install LG driver only. is it right for further step?
17. Click start(The Port 1 window should appear READY).
Don't show Ready.
May help? my phone has problem after kdz flashing.:crying: want to save via this way. :laugh:

Hi
ilovelg4ever said:
5. Turn Off phone, Remove your phone’s SIM and SD cards.
with battery? if with battery, will enter: S/W Upgrade mode for step 6&7.
Click to expand...
Click to collapse
1. after kdz the phone turn on? reset the phone!!
2- 5. no battery into phone... (if don't start S/W without battery instert battery but get error program at finish the update ... no problem error is because phone turn on after 80% automatically but phone is been update) holding “voll up button” and connect cable
ilovelg4ever said:
8.When computer detects the new hardware (Omap4430) release “voll up button”.
PC don't detects the New hardware (Omap4430), just install LG driver only. is it right for further step?
Click to expand...
Click to collapse
3- 8. I recommend reinstall all driver lg + omap
pc don't detect new hardware omap because you having flash KDZ already 'have the drivers on your PC..
ilovelg4ever said:
17. Click start(The Port 1 window should appear READY).
Don't show Ready.
May help? my phone has problem after kdz flashing.:crying: want to save via this way. :laugh:
Click to expand...
Click to collapse
4-17. in computer > go to device manager > looks com ports > your pc read LGE CDMA USB SERIAL PORT? set com41
No > start S/W upgrade phone but the pc don't read the phone test in other pc procedure and if don't work send phone in assistence ...
Yes > go to flash tool Click on Port COM settings (COM plug icon) and select port "1" press start and after you read start u holding “voll up button” connect the USB cable
I hope to have been of helped you

thanks for reply. i work sucessfully. let me share my experience with you.
No exact steps, just some points:
1) Use XP.
2) uninstall all old LG drivers.
3) install OMap & 2 LG drivers.
4) the phone come with battery (if no battery, my pc don't find my phone). Volume up + connect USB.
- Omap didn't appear (i don't know whether the reason is my phone installed OMAP beflore or not).
- Only LG 2-3 drivers to be installed.
5) execute LG flash tool, steps 12-17. Disconnects usb, battery off & in, volume up+connectUSB
6) The update process will begin automatically after that release the “vol up”.
7) phone reboot at 80% (showing "AP download SUccess"), counting continue. (whole procedure finish).
8) few mins later, target is resetting --> reset--..... (showing "Download Fail!)
thnaks grean again.

i have 2 Prada 3.0, the one normal can be flashed vai this way. the another is suck at "S/W screen when i turn it on. but can't be flased via this way, just keep "download fail" after 1-2mins updateing.

ilovelg4ever said:
i have 2 Prada 3.0, the one normal can be flashed vai this way. the another is suck at "S/W screen when i turn it on. but can't be flased via this way, just keep "download fail" after 1-2mins updateing.
Click to expand...
Click to collapse
sorry I can not help you for the second phone!

sorry 2 post

hi did you try to flash via smart flash too?

ilovelg4ever said:
hi did you try to flash via smart flash too?
Click to expand...
Click to collapse
Hi I don t have tested smart flash because crash on my sistem... but if it work on p920 I think that work for prada3..
Sent from my LG-P990 using Tapatalk

..

jbcagampan said:
..
Click to expand...
Click to collapse
read pvt regards

dont work on windows 7 64

Micromax a78!! Rooted!!!!

MICROMAX A78 ROOTED!!!
Guys!!! Micromax a78!! rooted!!!
So, here are the steps on getting root access on MICROMAX A78-
What you need
1. MICROMAX A78, data usb cable.
2. Download the Rooted Boot image file from the attachment below this post.
3. Download SP Flash Tool v2.1 from HERE.
4. Download MTK65xx Driver from HERE.
5. Download the MTK6573 Scatter.txt file from the attachment below this post.
6. Lastly download SuperOneClick root application for windows (search google), and install it...it will also install the adb drivers needed while rooting.
Installation Steps-
1. Unzip and Install the MTK65xx USB drivers on your Windows PC, just run setup.exe.
Connect your phone switched off and connect using USB cable. Windows will recognize and install the MTK drivers for your phone (any free COM ports) will be configured. Disconnect the phone. Do not switch on the phone
2. Copy the "rootedboot.img" file that you downloaded from my attatchment. Rename it to be boot.img
4. Extract and run SP flash Tool.exe (the one with Blue image icon)
5. Click on Options, check USB mode.
6. Click on Scatter-loading button which is on the right side below Downloading Agent. A window will open. Browse to your downloaded scatter.txt file. By default you will have only one map file of name MT6573_Android_scatter. Select this
7. The flash tool will populate the Map file on the application window. You will see multiple Entries such as
PRELOADER
DSP_BL
MBR
etc etc. Each will have a check box which is by default checked.
8. UNCHECK all entries EXCEPT FOR "BOOT". Leave boot checked. Now click on the "BOOT" just right to the checkbox and browse and select the boot.img (which was earlier rootedboot.img) file you downloaded from the attachment below.
9. Now click on "Download" on the Application or press F9 on keyboard. Warning messages will occur, but ignore them..
10. You will see in the status bar below "Searching"
11. Connect your phone (switched off and with battery inserted) via the USB cable.
12. Flash tool will do its stuff. First a red progress bar, then a count down, a quick yellow progress bar and final window showing Green Circle.
If you get this then Congrats You have flashed the unlocked boot.img!
NOW FOR ACTUAL ROOTING:
1. Restart your phone, now when the phone boots up, enable "usb debugging".
2. Now run SuperOneClick, and click "root"..after the process finishes, the a78 will be fully rooted with Superuser app installed!!.
Check by installing root checker from play store!!!
Enjoy !
Warning - Please follow the instructions. Don't mess around with anything else. Not responsible if you do anything else and brick your device !
In case you get any other error on SP Flash Tool, then recheck your MTK driver installation. Try on another PC.
Credits!
I, Me, Myself
GUYS! If u think my hardwork is worth something, do press the "Thanks" button below! Thank You! :fingers-crossed:

awesome work !!!
thankyou buddy !!! my phone is finally rooted now waiting for a custom recovery ........

I'll also make a custom recovery if you are interested
Sent from my Micromax A110 using xda app-developers app

I will post the result after testing your method on my A78. Lets hope for something good

Bro!! You are the best.. Thanks a lot!!!

abs_dear said:
Bro!! You are the best.. Thanks a lot!!!
Click to expand...
Click to collapse
That's good to know! Any problems anybody faces,m always there
Sent from my Micromax A110 using xda app-developers app

WOOT WOOT
vshlkmr buddy you are the BEST :good:
i tried with SOC bt didnt wrk..n i ws worried to play with SP flash tool coz i dnt hv any alternt phone...excellent job man...
will root my phone ASAP n let u know if i get any problms..
it'll be perfect if you can provide CWM recovery...
THANKS again..

Hi,
Facing a strange issue and that too at very first step. When I am connecting the phone (Switched Off) to USB Cable after Driver Installation, Windows detects the device and tries to install MT65xx PreLoader. But after a few seconds, it shows the error: Device Unplugged.
Can you plz help to resolve this ?
Thanks,
Param

paramjeetgem said:
Hi,
Facing a strange issue and that too at very first step. When I am connecting the phone (Switched Off) to USB Cable after Driver Installation, Windows detects the device and tries to install MT65xx PreLoader. But after a few seconds, it shows the error: Device Unplugged.
Can you plz help to resolve this ?
Thanks,
Param
Click to expand...
Click to collapse
Ok, I am able to resolve this by Disabling Searching Windows Update for Device Drivers.
And, YES, I have rooted my A78
Big Big Thanks to vshlkmr

Phone Finally from rotted to Rooted
Thanks Buddy...
Phone is finally of some use now.
vshlkmr said:
I'll also make a custom recovery if you are interested
Click to expand...
Click to collapse
Yes, we are very interested. please make a custom recovery for a78.
Thanks

[Q] How do I root Lenovo S890 (/get MT6577 drivers installed on Win7x64?)

I searched the forums but couldn't find any answers. This is the first time I'm trying to root an android phone. Things are not going well..
I found a page in Indonesian with instruction on how to root my sister's Lenovo S890. My dad bought her one in China, we live in Europe.
We need to get all the Chinese stuff off and install a "regular" Android version with a normal marketplace (read: whatsapp and google and nothing blocked).
The page with instructions is at http://www.duniaku.net/2013/03/30/u...rtisi-internal-storage-lenovo-ideaphone-s890/ I used Google Translate.
What are the steps? First you need to set up some files such as drivers are required to carry out the process of flashing, SP Flash Tool version 3.1222 or higher, because Lenny chipset MTK6577 S890, S890 and file TWRP to also file a Super User and Busybox will be pushed into the system through TWRP. All the files you can download from the following link:
1 Download Driver Lenovo : Extract file. rar it and then click Install_Driver.exe to install drivers into the system. Rather long process, just wait.
2 Download SP Flash Tool : The author gave the newer version, which v3.1224.01. .
3 Download Team Win Recovery Project : TWRP file is specific to the Lenovo S890, so do not try for another Android, although it also MediaTek chipset.
4 Download Super User and Busybox : Will we push into the system through TWRP custom recovery. Download and copy directly to SD Storage / Memory Cards-mu. Place it outside the / root folder or USB Storage Storage SD / USB storage from your Lenovo S890.
5 Download Data Repartition : This file is optional, just download and place it in the root folder Storage SD / USB Storage. Can later be used to repartition the internal memory is too small Lenovo S890. Author will explain at the bottom.
Click to expand...
Click to collapse
I first installed the Lenovo S890 drivers. Clicked "Install anyway" for everything and rebooted. No problems.
But when I connect the phone it's still complaining that it can't find drivers (and I can't find any official drivers on the Lenovo website either)?
I also installed the MT6577 USB VCOM drivers that I found here http://forum.xda-developers.com/showthread.php?t=2206421 (before I did this the SP Flash Tool did nothing).
I enabled USB Debugging mode on the phone, and took out the SIM, the SD card and the battery when I connect it to USB to the PC. I am running Win7x64.
Every time I try to run (step 2) SP Flash tool, it starts downloading fine, but then Win7 'spits out' the phone (I can hear the 'usb device disconnected' sound) and SP Flash Tool obviously stops working then and gives some error.
I think this is because the MediaTek MT6577 USB VCOM drivers somehow refuse to install correctly? It looks like rooting might go well once this driver thing is fixed?
When I force installation of the drivers I get a Code 10 error and a yellow triangle next to the Preloader and the MediaTEL Vcom something USB driver in Windows Device Manager. ( I searched the forums and didn't find a solution for this).
I forced installation by opening Device Manager, click Add, click Add Legacy Hardware - manual - choose the usb2ser_Win764.info file out of the MT6577 USB VCOM drivers folder
This is what's in the .inf file : Is there anything I can change here to force it to work?
[Version]
Signature="$Windows NT$"
Class=Ports
ClassGuid={4D36E978-E325-11CE-BFC1-08002BE10318}
Provider=%MTK%
DriverVer=05/30/2011,1.1123.0
[Manufacturer]
%MTK%=MTK,NTamd64
[MTK.NTamd64]
%MTK6218%=Reader,USB\Vid_0e8d&Pid_0003,USB\Vid_0e8d&Pid_1003
%MTK_COM%=Reader,USB\Vid_0e8d&Pid_0023&MI_00
%MTK_CAT%=Reader,USB\Vid_0e8d&Pid_0023&MI_02
%MTK_PRELOADER%=Reader, USB\Vid_0e8d&Pid_2000
%MTK_SP_DA%=Reader, USB\Vid_0e8d&Pid_2001
[DestinationDirs]
DefaultDestDir=12
[Reader.NTamd64]
Include=mdmcpq.inf
AddReg=Reader.NTamd64.AddReg
CopyFiles=FakeModemCopyFileSection
[Reader.NTamd64.AddReg]
HKR,,DevLoader,,*ntkern
HKR,,NTMPDriver,,usbser.sys
HKR,,EnumPropPages32,,"MsPorts.dll,SerialPortPropPageProvider"
[Reader.NTamd64.Services]
AddService = usbser, 0x00000002, Service_Inst
[SourceDisksNames]
[SourceDisksFiles]
[Service_Inst]
DisplayName = %Serial.SvcDesc%
ServiceType = 1 ; SERVICE_KERNEL_DRIVER
StartType = 3 ; SERVICE_DEMAND_START
ErrorControl = 1 ; SERVICE_ERROR_NORMAL
ServiceBinary = %12%\usbser.sys
LoadOrderGroup = Base
[Strings]
MTK = "MediaTek Inc."
MTK6218 = "MTK USB Port"
MTK_COM = "MTK USB Modem Port"
MTK_CAT = "MTK USB Debug Port"
MTK_PRELOADER = "MediaTek PreLoader USB VCOM Port"
MTK_SP_DA = "MediaTek DA USB VCOM Port"
Serial.SvcDesc = "USB Serial emulation modem driver"
Click to expand...
Click to collapse
How do I stop Windows from ejecting the phone (force it to keep it connected as the MediaTek thingie that seems to work with SP Flash Tool?).
Or is there a better way to get an English Android version on this phone?
When I now try to boot the phone it says
tool dl image fail
uboot is blocking by dl info
Did I (soft)brick it??
Thanks in advance for all the help!!

Giving up
Since this seems to be a less popular phone with very little support available - I'm giving up.
Spent 3 full days on this thing with no results, and I just read the GPS also won't work outside of China either.
Now all I need to do is figure out how to get it out of META mode or Factory mode, and get it to boot back into it's normal Chinese Android system.

katejones said:
Since this seems to be a less popular phone with very little support available - I'm giving up.
Spent 3 full days on this thing with no results, and I just read the GPS also won't work outside of China either.
Now all I need to do is figure out how to get it out of META mode or Factory mode, and get it to boot back into it's normal Chinese Android system.
Click to expand...
Click to collapse
Hi, I'm having a much similar problem, since I couldn't flash recovery with SP flash tool, the process was terminated unexpectedly showing error message s_ft_need_download_all_fail (4050), after a couple of days looking for a solution I decided to format the phone with SP Flash Tool, and it worked, right after I tried to flas recovery again...and it worked. I thought I had found the way but when I tried to boot the phone in recovery mode nothing happened, no matter what keys combination I use, how long I press them, the phone just won't react, it doesn't show anything on the screen.
I don't know if this was the logic step to follow, but if you want to try and discover what to do next, up to you, 4 hands are better than 2,maybe yuo find the solution.
Good luck.

There is no button combination to boot recovery, try droidgram-reboot on play store.
Sent from my Lenovo S880

Hope you guys manage to root it soon as I am one of those who waiting for it as I need to root my S890 also.
Sent from my Lenovo S890 using xda app-developers app

katejones said:
I searched the forums but couldn't find any answers. This is the first time I'm trying to root an android phone. Things are not going well..
I found a page in Indonesian with instruction on how to root my sister's Lenovo S890. My dad bought her one in China, we live in Europe.
We need to get all the Chinese stuff off and install a "regular" Android version with a normal marketplace (read: whatsapp and google and nothing blocked).
The page with instructions is at http://www.duniaku.net/2013/03/30/u...rtisi-internal-storage-lenovo-ideaphone-s890/ I used Google Translate.
I first installed the Lenovo S890 drivers. Clicked "Install anyway" for everything and rebooted. No problems.
But when I connect the phone it's still complaining that it can't find drivers (and I can't find any official drivers on the Lenovo website either)?
I also installed the MT6577 USB VCOM drivers that I found here http://forum.xda-developers.com/showthread.php?t=2206421 (before I did this the SP Flash Tool did nothing).
I enabled USB Debugging mode on the phone, and took out the SIM, the SD card and the battery when I connect it to USB to the PC. I am running Win7x64.
Every time I try to run (step 2) SP Flash tool, it starts downloading fine, but then Win7 'spits out' the phone (I can hear the 'usb device disconnected' sound) and SP Flash Tool obviously stops working then and gives some error.
I think this is because the MediaTek MT6577 USB VCOM drivers somehow refuse to install correctly? It looks like rooting might go well once this driver thing is fixed?
When I force installation of the drivers I get a Code 10 error and a yellow triangle next to the Preloader and the MediaTEL Vcom something USB driver in Windows Device Manager. ( I searched the forums and didn't find a solution for this).
I forced installation by opening Device Manager, click Add, click Add Legacy Hardware - manual - choose the usb2ser_Win764.info file out of the MT6577 USB VCOM drivers folder
This is what's in the .inf file : Is there anything I can change here to force it to work?
How do I stop Windows from ejecting the phone (force it to keep it connected as the MediaTek thingie that seems to work with SP Flash Tool?).
Or is there a better way to get an English Android version on this phone?
When I now try to boot the phone it says
tool dl image fail
uboot is blocking by dl info
Did I (soft)brick it??
Thanks in advance for all the help!!
Click to expand...
Click to collapse
please use S890_Customized_SP_Flashtool_20121119(v3.1238.5)
flash again ok
i am solve same your problem
https://www.dropbox.com/s/pwvg553v5z1vtju/S890_Customized_SP_Flashtool_20130109(v3.1238.5).rar

kyaw8719 said:
please use S890_Customized_SP_Flashtool_20121119(v3.1238.5)
flash again ok
i am solve same your problem
https://www.dropbox.com/s/pwvg553v5z1vtju/S890_Customized_SP_Flashtool_20130109(v3.1238.5).rar
Click to expand...
Click to collapse
Thanks for sharing. Is it 100% working or still in testing phase?
Sent from my Lenovo S890 using xda app-developers app

nakTT said:
Thanks for sharing. Is it 100% working or still in testing phase?
Sent from my Lenovo S890 using xda app-developers app
Click to expand...
Click to collapse
i fix 2pcs

kyaw8719 said:
i fix 2pcs
Click to expand...
Click to collapse
Meaning?
Sent from my ST26i

doesn't solve the problem
nakTT said:
Meaning?
Sent from my ST26i
Click to expand...
Click to collapse
It doesn't work same problem downloaded the latest SP Flash from the post doesn't work either.. Is there any of you solved the problem? If so then please go detailed about it.

[Tutorial] Revive dead Karbonn A9+/CM Flare after JB update

Follow this guide carefully and you can revive your dead Karbonn A9+/ CM Flare after Jelly Bean Upgrade.
Tools Needed:
Dead Phone (When u connect to PC it should install Qualcomm HS-USB QD Loader 9008 Driver) Link
QPST.2.7.399 Link
Flare Revival kit Link
PC with 32 bit Windows (XP/Vista/7/8) (64bit casus problem in QPST installation)
Credit goes to jhanra for the tutorial as well as CWM 6.0.1.1 for JB ROM . :good:

Procedure
Connect ur phone to PC and let the driver install
Install QPST
Open QPST Configuration (in Win XP compatibility mode) ->Add new port -> Select the com port of your device ->exit.
Go to Start -> All Programs -> QPST eMMC Software Download open the tool -> Check program boot loaders -> Browse for the device com port
Extract Flare Revival Kit on desktop
If Phone is not detected , Click Browse
In flash programmer file name type MPRG8X25.hex -> in Boot Image type 8X25_msimage.mbn in SPC ->000000
Click Load XML def and browse for rawprogram0.xml in Flare Revival Kit
Click Load Patch def and browse for patch0.xml
Check the search path 2 and browse for the folder flare repair files
Now click download, wait for the download to finish (it never finish but it also detects for a new driver, and that’s important) and it will search for the new hardware found, install the driver
From here you can updating your rom to jelly bean using this tutorial Link

Guys, anyone encountering "Cookie (if present) not received" error after clicking on Download button?
My Karbonn A9+ as successfully updated to jelly bean, which was working flawlessly for 3 days. But suddenly it died while my charging my phone.. The phone could not be turned on, no fastloader or entry download mode.... However when connected to PC it was being detected as Qualcomm HS-USB QD Loader 9008. I tried this tutorial but am facing cookie not received error.
Since my phone died suddenly, not during any update firmware process... I suspect this could be case of Sudden Death Syndrome (SDS) which means my eMMC flash (internal storage) got corrupted and is not being able to recoginized by QPST tool.
Has anyone faced this problem?

kornholic said:
Guys, anyone encountering "Cookie (if present) not received" error after clicking on Download button?
My Karbonn A9+ as successfully updated to jelly bean, which was working flawlessly for 3 days. But suddenly it died while my charging my phone.. The phone could not be turned on, no fastloader or entry download mode.... However when connected to PC it was being detected as Qualcomm HS-USB QD Loader 9008. I tried this tutorial but am facing cookie not received error.
Since my phone died suddenly, not during any update firmware process... I suspect this could be case of Sudden Death Syndrome (SDS) which means my eMMC flash (internal storage) got corrupted and is not being able to recoginized by QPST tool.
Has anyone faced this problem?
Click to expand...
Click to collapse
Please state your OS Win XP or 7. Try using 32 bit win XP PC.

arunmcops said:
Please state your OS Win XP or 7. Try using 32 bit win XP PC.
Click to expand...
Click to collapse
My os is windows 7 32 bit.. i tried running emmc downloader with windows xp compatibility mode also. same problem.

kornholic said:
My os is windows 7 32 bit.. i tried running emmc downloader with windows xp compatibility mode also. same problem.
Click to expand...
Click to collapse
QPST caused me problems with Win 7. I used win XP.

arunmcops said:
QPST caused me problems with Win 7. I used win XP.
Click to expand...
Click to collapse
Tried it on Win XP... same cookie(if present) not received error showing..

can we use vmplayer for the win xp or other virtual soever instead? i use win 8 64 bit that's why it won't able me to download and shows me the message that the cookie (if present) is not received. :angel::angel::angel:

Some from a chinese forum was able to fix the cookie problem through QFPROM Fuse..
http:// lepad.it168.com/thread-2920933-1-1.html
(its in chinese)
What does it mean?

kornholic said:
Some from a chinese forum was able to fix the cookie problem through QFPROM Fuse..
http:// lepad.it168.com/thread-2920933-1-1.html
(its in chinese)
What does it mean?
Click to expand...
Click to collapse
Only explanation given is that This problem is related to specific PC.

arunmcops said:
Only explanation given is that This problem is related to specific PC.
Click to expand...
Click to collapse
Yes the person in one post first said the problem is due to PC and driver combination. However, in later post has also said:
"i am still stuck in download mode. i was able to programm the bootloader, as i mentioned before by using QFPROM Fuse, everything else leads to errors. only one little detail changed -> when i press the power button it vibrates shortly.when i try to porgram the mmc device i always get no response from the phone."
Some of the points to ponder are:
1. He said he was able to program bootloader using qfprom fuse.
(How did he program bootloader through qfprom fuse, what does this mean?)
2. When power button pressed, there is vibration...
(On my device there is no response when pressed on power on.)
3. However he later said when he tries to program mm, he gets no response.
(He has not said he gets cookie error, just not response... could be anything)

one of the moderator of cherry flare group at facebook was able to revive phone from cookie error.
check http://www.youtube.com/watch?v=qHQIIsqV1Zw

i just found out that you can restore your phone too by using roadkill, if you had written the backup of the image of your phone lately. :angel:

heyyanyan said:
i just found out that you can restore your phone too by using roadkill, if you had written the backup of the image of your phone lately. :angel:
Click to expand...
Click to collapse
yes, if you could access entry qpst download mode (vol down + power)... however if you are hard bricked... you would not be able to access that plus your phone would not turn on in any manner.

in my case, my phone didn't turn on no matter what i do. but if i connect my phone to the pc, it shows the qualcomm hs-usb something that can be read by roadkill.

heyyanyan said:
in my case, my phone didn't turn on no matter what i do. but if i connect my phone to the pc, it shows the qualcomm hs-usb something that can be read by roadkill.
Click to expand...
Click to collapse
did you manage to fix your phone?? ......................................................

arunmcops said:
Connect ur phone to PC and let the driver install
Install QPST
Open QPST Configuration (in Win XP compatibility mode) ->Add new port -> Select the com port of your device ->exit.
Go to Start -> All Programs -> QPST eMMC Software Download open the tool -> Check program boot loaders -> Browse for the device com port
Extract Flare Revival Kit on desktop
If Phone is not detected , Click Browse
In flash programmer file name type MPRG8X25.hex -> in Boot Image type 8X25_msimage.mbn in SPC ->000000
Click Load XML def and browse for rawprogram0.xml in Flare Revival Kit
Click Load Patch def and browse for patch0.xml
Check the search path 2 and browse for the folder flare repair files
Now click download, wait for the download to finish (it never finish but it also detects for a new driver, and that’s important) and it will search for the new hardware found, install the driver
From here you can updating your rom to jelly bean using this tutorial Link
Click to expand...
Click to collapse
!!!

!? I just Ported CWM 6.0.1.1 to CM Flare Jelly bean (for JELLY BEAN ONLY)!! !!!! I Already test it with my own 3pcs CM FLARE phone with no problem! In porting this CWM my 2 phone died porting this CWM but I recover it WITH THIS METHOD you posted!!!!!!!!!!!!!!
FLash this with AIO FLASHER
check recovery erase then flash
View attachment 2089726
theres nothing it can do if you try it? it cannot mess your phone!
!!!

this is the full tutorial for this! View attachment 2089809,
and this is the file for this case!
h ttp://www.4shared.co m/rar/rzVTMMxY/flare_repair_files.html
after this you can flash BP firmware in this! follow the tut in flashing BP Firmware and so on
to upgrading in jelly bean BY ARUNMCOPS! here ht tp://forum. xda-developers.com/ showthread.php?t=2330823
the original thread is here ht tp://www.pinoy den.com.ph/inde x.php?topic=274677.0
Note: just erase the spaces of the link!
you can try the steps on my tut but DO THIS AT YOUR OWN RISK!!!
!!!!!!
[email protected]@@
[MENTION=1065870 [user=1879310]@@@@[/user][/MENTION]
@@@

kornholic
@@@????

Soft bricked Panasonic P81

Hi Friends,
This is my first post at XDA.
I unfortunately bricked my Panasonic P81 after rooting it and adding XHalo app and the boot manager app from the Xposed Framework.
The situation is as follows-
I can get to the logo, it screams Panasonic and then doesnt boot. I dont have CWA installed and worse, my SD card which had my stock backup is also lost. This means I need a mechanism to stock recover and perhaps flash boot.img and recovery.img?
I am stuck at this point, not sure how to proceed. I can get to recovery, have cleaned cache, backed up user data ,done a factory reset. Even after factory reset it still cant boot.
Please help me with a step-by-step instruction to recover, this phone is dear to me. How do I flash?(boot.img or rom) I have downloaded Sagar Patel's (good bless him!) backup and the images, but need guidance on how to flash and recover.
Please help friends and apologies for any incovenience. I am still a newbie

Guys please help!!

Driver-USB-PC connection problem
kartik.krish said:
Guys please help!!
Click to expand...
Click to collapse
Hope drivers are installed properly in your pc.
If you are going to use sp flash tool, Make sure SP flash tool is set to auto-detect com port, not manual selection
If you find that it is driver problem, following may help you.
Please note that there is nothing that much hard in driver installation as it is just to connect your device with your pc but because many users still face problem of driver installation, you can try following tricks!!!
It is observed by me that driver installation and adb interface problem do not happen in windows XP as eventually and generally it is happened in windows 7 and later…so, you can simply try on windows xp if you are able to do so…(you can use dual operating system too!!! Or good relation with neighbor/friends/colleagues/someone/all can be beneficial here!!!)
Note that all tricks here are not necessary to work, but it may still work for you….
Take one by one step, if the first step does not work for you, only then try next step. This is not all steps to be taken at once type guide…This is simply Try and error type tutorial/tricks…
There are following problems I have come to know regarding to driver installation and conflicts:-
Device is charging through usb cable but there is no usb option displaying on either device or no driver installation box/message/pop up appears in pc….
Missing sound of that usb-pc connection
Sound of disconnection after couple of seconds of connection
Adb interface is missing
Ok, sometimes changing usb connection type for example, from mass storage or mtp to camera, ptp, usb tethering or something else can bring adb interface…..
Try with different USB Cable. You can use original nokia or samsung tiny cable instead of cable having long length. Sometimes, length matters!!!!
Try in different USB Port.
Sometimes, you have to disable signature verification in your pc for proper installation of driver.
Had you disabled your antivirus before downloading, installing and while running your tools/softwares? You may need to do so…
Have you installed the software (or say, all associated softwares/tools) in C-System drive?, if not, then you should first install required software/tools in system drive that is usually C drive in Microsoft-Windows OS…or try after installing them on desktop.
Keep all necessary files/tools (driver files, flash tools, rom etc…) on desktop.
Download proper driver According to your model/device, According to chipset inside, According to Official site of manufacturer, Official site of chipset, through PC Suite/flash program of your device…
If the problem still not solve, you should try all available driver packages of your device one by one whether from official site of chipset inside your device, or any forum, adb, pdanet+ or foxfi, universal driver, VCOM Port driver, drivers from hexamob through play store, and find all possible packages and see if someone make positive result after installation…
If the problem still not solve, you should install remaining update packages of your system (PC) including all primary, secondary, essential, Non-essential updates….whatever, just install them all….reboot your pc…and see if problem is solved….
If you can connect the device but somehow found that device driver still not installed properly, just go to device manager in your pc, click on portable device, right click on your device and apply “Update driver”. Click on “automatically search” when a window prompt ask you.
If the problem still persists then,
Just remove all the drivers using usbdeview (I have given link also to download usbdeview in earlier post)
https://drive.google.com/folderview?id=0B511A2txfpAPbmwtQXZqbnVlT1U&usp=sharing
Install usbdeview and remove all the drivers
You can also fix this by showing the nonpresent devices in devicemanagement (google for show nonpresent devices for explanation)
Go to com ports, and delete all mediatek drivers except preloader driver. Now start over. It can help if you choose the same usb port where you had success last time.
Use Usbdeview to uninstall all the drivers before connection, restart the pc, Extract and keep driver zip files and other useful files/tools on desktop…just start your tool… and try to perform your tasks like backup…or restoring the backup…without worrying about that sound of disconnection you may listened after couple of seconds of connection or don’t even worry if you are just missing that sound of usb-pc connection….just try on your tool…
If still problem of driver installation persists, then simply use usbdeview and uninstall all drivers, restart your pc and try following steps:-
There are various ways to install proper drivers at the time of connecting the device with pc depending upon how you connect it.
Follow the procedure both with and without battery
Simply plug in via USB Cable
Connect by holding volume down button
Connect by holding volume up button
Connect by holding Power button
Connect by holding power and volume down
Connect by holding power and volume up
Connect by holding both volume up and down button
Connect by holding thrice volume up, down and power button
Connect by holding power and home button
Connect by holding power and menu button
Remember which method works and which drivers are installed
in LAN-Devices you may have different android device
Select/set drivers by hand and use the mtk usb driver, now Flashtool finds the phone
Suppose holding volume down method without battery works for you then what next you have to do is as below:-
1.TAKE THE BATTERY ,SD ,SIM OUT OF THE PHONE
2.HOLDING VOLUME DOWN CONNECT IT TO PC VIA USB(ONCE YOU HEAR A SOUND FROM PC YOU CAN RELEASE VOLUME DOWN)
3.OPEN DEVICE MANAGER(ON COMPUTER SEARCH IT OR CONTROL PANEL)
4.WAIT FOR 2-3 MINUTES
5.YOU WILL HEAR A SOUND & OTHER DEVICE WILL BE DISPLAYED
6.IN OTHER DEVICES ->MT65XX PRE-LOADER
7.RIGHT CLICK MT65XX PRELOADER
8.UPDATE DRIVER
9.LOCATE THE DRIVERS PROVIDED ACCORDING TO YOUR OS(VISTA,WIN7,XP)
10.IT WILL DO ITS STUFF
Install Mediatek drivers, preloaders, VCOM port etc…
Manually Install MediaTek USB VCOM Drivers
Requirement:-
1. Download MediaTek USB VCOM Drivers
2. Download USBDeview
Here is the link from you can get it:-
https://drive.google.com/folderview?id=0B511A2txfpAPbmwtQXZqbnVlT1U&usp=sharing
Procedure
(* Note: You might need to disable drivers signature verification in Windows for this to work smoothly.
If you want to turn off device driver signing in Windows completely, do the following.
Windows 7:-
1. Hit the Win+R keys together to open the run dialog
2. Type gpedit.msc to open the local groups policy
editor
3. Expand ‘Administrative Templates’ (it’s under ‘User Configuration’)
4. Expand ‘System’. Click ‘driver Installation’
5. In the right panel, double click on ‘Code Signing for Device Drivers’
6. Choose ‘Enabled’ in the window that appears.
7. In the underlying options, choose ‘Ignore’
8. This disables drivers signing in Windows 7, and now you can install unsigned drivers in Windows 7.
9. Click Apply, OK. Restart your computer to install unsigned drivers
Windows 8
1. Hold down the Windows key on your keyboard and press the letter C to open the Charm menu, then click the gear icon (Settings)
2. Click More PC Settings
3. Click General
4. Under Advanced Startup, click Restart Now
Note: In Windows 8.1, the ‘Restart Now’ button has moved to ‘PC Setting -> Update & Recovery -> Recovery.’
5. After restarting, click Troubleshoot
6. Click advanced options
7. Click Windows Startup Settings
8. Click Restart
9. After restarting your computer a second time,
choose Disable driver signature enforcement
from the list by typing the number 7 on your Keyboard Your computer will restart automatically.
10. After restarting, you will be able to install
unsigned drivers normally; however, Windows
will display a warning message. When the
warning appears, click Install this driver
software anyway. )
1. Install USBDeview and use it to uninstall all Vcom, Mediatek and Preloader drivers
1b. Extract the contents of the Mediatek USB VCOM file
2. In Windows, go to Control Panel and open Device Manager
3. Click any of the device groups (any of the items on the list) you see there, and then from Action menu, select Add legacy hardware
4. Add hardware wizard will be opened, click next
5. Select Install the hardware that I manually select from a list (Advanced)
6. Click next two times and click Have Disk button
7. Click browse and find where your driver's .inf file is, then select it (the .inf you'll select is located in drivers > USB Vcom driver > your OS) . Ensure to select the 64 bit .inf if your PC is 64 bit
8. Click Open and OK. You will see the drivers listed.
9. Select your driver there (select Mediatek Preloader USB VCOM Port)
10. Click Next and finish installing
11. If SP flash tool or other software still dont detect your phone then also install Mediatek DA VCOM (consider installing more from the list of drivers one at a time if need be)
Try in different PC
Sometimes windows XP works when windows 7 fails!!!
Case:-
It did the same thing with my MT6577 (Wiko Cink PEAX), so I connected it with a battery and without holding VOL+. Then "MT65xx preloader" appeared in device manager then disappeared (once). It is normal that it disappears. When you start Flash_tool and when you click Download (or whatever you want to do) THEN you connect the phone (in off state), and the flash operation will succeed.
Guess what? Once my Panasonic P81 could install driver and got detected after approx. 5 hours of continuous connection with win 7 x64!!! Meanwhile, I tried first usbdeview and then manually installation of mediatek driver but manual installation had failed as my p81 was only charging when it was connected with pc….So, mediatek – windows 7 conflicts….but, when I tried tiny (very small) nokia usb cable, it works instantly…
If you ever meet problem when you connect your android with your pc via usb cable and find that your android is charging but could not recognize or there isn’t that options of “USB connection” then just disconnect your android, power off it, remove battery, connect it without battery with your pc through usb, let it have some time to recognize your android or hear that voice of “usb connection” you were just missing…after that, insert battery and switch on your android…you are done!!!
Sometimes removing both sim cards and battery and then re-inserting them after a couple of seconds also works.
Try with different USB Cable
Try in different USB Port
Try in different PC
Sometimes windows XP works when windows 7 fails!!!
Use usbdeview to remove all the usb devices and then add your device
Find proper driver of your device:-
https://drive.google.com/folderview?id=0B511A2txfpAPbmwtQXZqbnVlT1U&usp=sharing

panasonic p81 soft bricked
SP flash tool detected my P81 mobile
but i need rom ROM files to flash
please any one give me rom file to flash Panasonic P81 with SP flash tool

problem solved?
I also had similar problem & solved it. Tell me if the problem is no solved.

damn i don't know what the hell is going on inside my computer but i am not able to get those drivers or i don't know what's the problem. please help me where to get drivers for my panasonic p81 mobile. it is softbricked and i want to install stock rom and i have that cpb files but that ygdp tool isn't working i am in total chaos.
help me please

kartik.krish said:
Yo! I had bricked it too and that too by Xhalomulti window cuz app window is sh!t..... be cool .there is stock rom available at www.xdafirmware.com....google it....also You will recieve a .zip... extract to get .cpb file and use YGDP (assembly:: if ask for password at ygdp type 369)......tap config select cpb. Wait ...connect usb and click start........ok tutorial on Internet.... IMPORTANT THING:: YOU'LL NEED MTK VCOM DRIVER PR ELSE IT WON'T WORK.
Sent from my Panasonic P81 using XDA Labs
Click to expand...
Click to collapse

Thanks so much mate! I fixed with the help of friends at XDA. Which ROM performs best on P81 which runs L or M? I am still on stock and need to upgrade. Do you have suggestions?

kartik.krish said:
Thanks so much mate! I fixed with the help of friends at XDA. Which ROM performs best on P81 which runs L or M? I am still on stock and need to upgrade. Do you have suggestions?
Click to expand...
Click to collapse
Brother I am tired of finding any rom other than stock.on internet there is miui 6 but most people complained it damaged their devices....no cyanogen OS,Color os ,Aokp,Ressurection remix,paranoid nothing........ok i found a phone named Doogee Dagger DG550 having same spects but better ui than playmore and that recently got kitkat too. Im thinking of trying it..if it fails i've
Panasonic original (ok modded a bit) firmware i can flash from ygdp tool..... actually Panasonic P81 is nothing but clone of coolpad 7320 with cool show replaced by playmore and the gesture is new....same multiwindow and the music cafe is nothing but coolpad music renamed....literally im using 7320 rom with build. prop changed so on apps it shows im using p81........Ok if you find rom please post link..... Ps ive tried roms on www.needrom.com but is hopeless.
Sent from my Panasonic P81 using XDA Labs
---------- Post added at 04:39 AM ---------- Previous post was at 04:34 AM ----------
kartik.krish said:
Thanks so much mate! I fixed with the help of friends at XDA. Which ROM performs best on P81 which runs L or M? I am still on stock and need to upgrade. Do you have suggestions?
Click to expand...
Click to collapse
In my opinion MIUI is best because it has a self large community like xda and launch updates per month so many that you will fed up installing them.....if you download and install one update you will be amazed that it will say 3 more system updates pending......and if you complain a bug next month it got fixed.....only thing is to find one...
PS don't download the miui 6 for p81..complained by many p81 user that it hard bricked the device.
And that miui is not official i.e. some developer made his own one and DO not tested that it works or not......
Sent from my Panasonic P81 using XDA Labs

Sir,My Panasonic eluga s is soft bricked, Not starting by pressing any key..it only Starts when connected to PC or charging.. That too in Fastboot mode.. While installing stock ROM using YGDP tool,I am not able to get my mobile in download mode..pls guide..

my panasonic p81 is hard brick,it is not detecting in pc by vcom and other drivers even not booting or charging,please help me devs.

I am connecting my p81 with my sound system but now i cannot hear the voice over a call properly plzz help me out