Hi every body!
I have a problem with my phone. It is deviated to left so that I can't press the number 3. When I press number 3, it effect to the number 2. I used align screen function to fix but I have problem with align screen. I touched to the target for 40 minute but the target still continue. Then, I reset my phone( although the align screen still continue) but the phone's status haven't still improved( it is still deviated to left).
How must I do?
Please give me your help. Thanks a lot.
Related
OK, heres the deal..
Yesterday I managed to crack the bottom-left corner of my BA screen (damn medkit shifted onto it in my car glovebox ).
As i was checking to see how much of the screen was still responsive (seemed OK, still usable, only the 'New' button and the bottom item of the menu didnt work) the battery died (as in completely, hard reset died)..
So i plug in the power, and start the familiar initial setup. I get to the callibrate screen screen and am unable to continue..
So my question is: Is there any way to bypass the calibrate screen section of the initial setup? Im pretty sure enough of the screen still works for the device to function, if only i could get past this damned calibration screen..
Clearly i cannot bypass it completely, as the screen does need to be calibrated - but is there any way I can recover my BA?
Cheers All
Check out this thread:
http://forum.xda-developers.com/viewtopic.php?t=1910
or this one:
http://forum.xda-developers.com/viewtopic.php?t=6855
Also, if you can still see the image it means that only the digitizer (touch sensitive part) is broken, and not the screen so it shouldn't cost to much to replace.
And remember - search is your friend! :wink:
This might be a bit toooo late, but just in case some one is stuck with a broken screen as dabs and I were.
I received a k-jam (lucky me, it was for free) with a broken touch screen, it was left uncharged for a long time so after charging it, it entered the unwelcomed welcome mode (you know, align, copy, time zone ...) and there were no way of passing this part of initialization.
I had to do some search over the net, and I found a good article here ((Can I use a PDA that has a broken touch screen)) http://www.pocketpcmag.com/blogs/index.php?m=200510 which advised the use of "RemoteCalibration.exe" directly from the pc. This killed the welcome.exe program and I managed to re-use the K-jam again. The only draw back about this way is that I will have to connect the K-jam to a pc every time I hard reset, I hope there is a way to do the same action via mini sd cards.
After that, I installed fakecursor (but I'm looking for a better sw to emulate the touch screen function as this one cancels most hardware buttons on the devise) but at the moment, I'm using all the k-jam's functions.
Hope this would be of help to some one out there
Hi!
The screen of my Prophet works correctly.
After I've installed a contributed rom, my device boots correctly (after hard reset) and then ask me to align screen but just after I tap to enter in align procedure, it didn't give response anymore! So it enter (tapping the screen) in the align procedure, but then no repond any nore!
I tried to install other roms but... nothing to do: the is always exactly the same:-((
What can I do? Go back to WM5?
What's the correct procedure? I didn't found it...
I've tried to and...
Now I've installed NVID rom
but when appears "tap here to set up your Windows Mobile-based device" I tap on the screen (so touchscreen works) then pass to "align screen"
here if I touch normally it didn't work but if I press and move a little the pen on the cross (like designing very little circle) it works.
After alignment procedure, Prophet seems to works regularly, I mean I just nee to simply touch screen and it works.
Do you think it's the beginning of an hardware problem?
this happened to me as well. i can't touch the centre cross hair, but can with my finger, the other cross hair i can tap with the stylus. also on the keyboard, i can't tap esp the no. 8 & few letters below it esp G.
still happens to me even with another rom. don't know how to correct it. i guess a new screen is the key... or get a new pda - i'm waiting for my touch pro!!
all roms problem
Yep, it seem like it don't receive a spot area touch, but only wide area touch.
But this appens to me for «all» roms I tested and «only» for alignment procedure!
After I get screen aligned, it works perfectly, and seems to have normal sensitivity.
The problem is only for align procedure!
But it sounds strange that you can't use "8" or "g": it seems really a problem with touchscreen or maybe it is to clean a little.
But you are a lucky man! Touch pro is coming in your hands...
Bye
Hello there,
I have problem with my screen alignment.. ASUS P535. It repeats again and again.. I updated my ROM and nothing happend. Then I've changed digitizer on my LCD. It worked, but for 1 time. When fresh copy of ROM started. Screen alignment was correct. When I've got loaded my WM device restarted and asked to align screen. And nothing happend. And it again repeats.. What should I do now? Maybe is there a way to upload screen align file direct to my ASUS P535? Or any other suggestions..
This happened to my bother-in-law on his omnia. he had it replaced 3 times. 3 devices, 3 bad screens after a few weeks each. The alignment was way off, and if he hard reset.. he got stuck on the alignment screen and could not go past it.
Tapping all 4 corners and then the center should all line up perfect or it will repeat until it's right. If the screen is messed up.. (Not registering the taps accurately) this would cause your problem.
I know you replaced your digitizer, but I think you have bad hardware.
did you notice the screen was not accurate before this happened?
Yes. It was not accurate. Half screen from top was accurate, but other half not.. I had to tap screen ~1cm lower to hit correct 'button'.
Ok.. If hardware is broken. So then which part? Or just I'll take my device to pro to fix it.. If it will be possible..
I also used Remote Screen Alignment software. It solved align problem, WM is working, but everywhere I tap, it taps bottom right corner.
Need help please!
Yota 4G max – Chinese copy. I bought the mobile two weeks ago and was working fine, running Windows mobile 6.5 Professional. I set up locking on keys when phone is idle not in use to be locked, when I want to unlock I just slide and type in the password. Then I decided to install stupidly most of the software that was provided on the disk (Chinese stuff) and restarted the phone. It came up to the slide button where I use to be able to slide and provide the password to go into windows. But I was not able to do slide and type in password (the touch screen was not responding) so I am not able to go into windows, while installing something must have corrupted some files? After few tries now it comes up with a screen saying - Several incorrect passwords have been entered. To continue entry, enter ‘a1b2c3’ but I am not able to press on the keys on the screen keyboard since the whole screen is locked. Can anyone please, please tell me if there is a way to overcome this problem? It will be appreciated & thank you in advance.
My sister just bought a Quantaray 7" Tablet from a co-worker. The biggest problem was that he forgot his pattern lock, so using the tablet was quite difficult. There was also a problem with it not wanting to DL directly from the marketplace. Screen was working perfectly.
In order to correct these problems, I did a factory reset and wiped cache via bootloader mode. That fixed the above problems, but made it so now the screen calibrations are inverted. Meaning that if I want to press the "1" button on the keyboard, I have to touch the "0", or touch "q" to register "p". In other words, (while being held vertically) I need to press the bottom right of the screen to hit a button on bottom left. I've tried completing the screen calibration during initial setup, but it won't allow me because its so far off.
Running; Android 2.1-Update1 and Kernel 2.6.29 root(at)localhost #154
TL;DR - Touch screen inverted after factory reset (touch on left to press button on right). Need solution.
sorry for the bump, but I'm hoping that someone could still help