Related
AFTER UNLOCK NO VOICE OR SPEAKER WORKING I JUST FLASHED WITH
(RUU_Kaiser_HTC_WWE_1.25.405.0_22.39.82.00.b_1.27.04.15_Test) NOW PHONE DOESNT
POWER UP OR BOOT MODE BLANK SCREEN
I TRY TO CONNECT TO THE COMPUTER ASKING DRIVER (DATE INTERFACE)
I NEED YOUR HELP TO GET BACK LIVE
PLEASE
THANKS
How did you unlock it? Did you CID unlock? HardSPL version? Can you get to the bootloader by holding down the camera button and power button and soft reset at the same time?
From the sound of things you loaded a CID locked rom onto your locked phone. This is only a guess though based on the fact that the ROM you loaded included a compatible radio.
Just a tip, next time don't use all caps. It's considered shouting and inappropriate. We understand your urge to get it fixed so we'll help even without the caps
Answering Alibaba0101's questions will help a lot. Also, have you tried taking the battery out and putting it back in?
The phone was on orange.
Step 1: install JumpSPL1.93-KAIS.exe
Step 2: Run KaiserUnlocker.exe (PolarisUnlocker)
Step 3: Flash Hard-SPL (but the screen goes white then i boot the phone manually by pressing camera button) after done.
Step 4: Run unlock Radio (take couple of mint and done and phone reboot)
Step 5: Run Unlocker ( after run unlocker i get 2 option unlock and super cid 000000 and I click checked both option and press okay its take less then 1 mint done.
Step 6: i take it out battery from the phone put different sim card and power on the phone phone was unlocked when I dial help line i didn’t get any sound. No speaker no ear sounds.
then i flashed (RUU_Kaiser_HTC_WWE_1.25.405.0_22.39.82.00.b_1.27. 04.15_Test) and after done flash phone dead screen blank I try to boot the phone by pressing camera button but phone not responding after connect the usb to phone get msg (DATA INTERFACE) driver.
Phone still dead i try to put another battery but still same I did try soft reset hard reset but still dead
Please help
THANKS
lxa786 said:
The phone was on orange.
Step 1: install JumpSPL1.93-KAIS.exe
Step 2: Run KaiserUnlocker.exe (PolarisUnlocker)
Step 3: Flash Hard-SPL (but the screen goes white then i boot the phone manually by pressing camera button) after done.
Step 4: Run unlock Radio (take couple of mint and done and phone reboot)
Step 5: Run Unlocker ( after run unlocker i get 2 option unlock and super cid 000000 and I click checked both option and press okay its take less then 1 mint done.
Step 6: i take it out battery from the phone put different sim card and power on the phone phone was unlocked when I dial help line i didn’t get any sound. No speaker no ear sounds.
then i flashed (RUU_Kaiser_HTC_WWE_1.25.405.0_22.39.82.00.b_1.27. 04.15_Test) and after done flash phone dead screen blank I try to boot the phone by pressing camera button but phone not responding after connect the usb to phone get msg (DATA INTERFACE) driver.
Phone still dead i try to put another battery but still same I did try soft reset hard reset but still dead
Please help
THANKS
Click to expand...
Click to collapse
I don't see the step where you flashed your original radio back after doing the SIM unlock. The radio that you is a special "patched" radio, and the phone will not successfully boot into Windows with it flashed.
Go into the bootloader (hold Camera during power on), and flash a compatible radio. If you haven't flashed a cooked ROM yet, then just hit up the Kaiser Wiki and grab the original ship radio for your phone.
Bootloader is entered by holding the power button and camera button down while soft resetting the phone. (sticking the styles in the hole) Keep holding the 2 buttons down until your in bootloader. Even with the wrong radio the phone should still go into bootloader properly
austinsnyc said:
Bootloader is entered by holding the power button and camera button down while soft resetting the phone. (sticking the styles in the hole) Keep holding the 2 buttons down until your in bootloader. Even with the wrong radio the phone should still go into bootloader properly
Click to expand...
Click to collapse
huh. I don't have to hold down the power button to enter the bootloader. I just hold down the camera button and put the stylus into the reset hole.
Boot Loader
Same here I just hold down camera button and soft reset works every time.
hi I need your more help how can I get phone on boot mode phone dead not responding I tried more then 10 time by pressing camera and power button phone still blank screen.
No display show so how can I flash the phone
Any idea to flash the phone dead mode?
thanks
If you cant get it into boot loader mode, ur gonna have a lot of trouble trying to fix it. Like everyone has said so far... Press and hold both the Power button and Camera button together and then use your stylus to soft reset it.
This has gotten people in the past, so sorry if it sounds dumb.
The Camera button has two settings Full Press and Half Press. Press until it stops then press again. You need to be pushing the Camera Button down all the way to get into Bootloader.
Also I never need to press the power Power Button As well.
I may be wrong but, when the phone is on, you can press the Camera and Soft Reset buttons. When the phone is off, you press the Power, Camera, and Soft Reset buttons to go directly into boot loader.
i tried but screen still blank no light nothing when i put usb into the phone asking driver (data interface)?
Can not go in bootloader help?
Tytn 2 is dead .
Ok last night I try to install the new hyperdragon III BlackStone rom everything is fine untill it finish and it cant load in to window, the computer keep asking me for the data interface and the tilt keep restart and the screen only shows hyperdragen III. I was running hyperdragon III opal (10/11/08) I tried MMTY and reinstall the OE rom but no luck, please help!!
Tytn2 Dead or not??
Tytn 2 is dead if you see data interface driver when put in usb cabel install v3 motorola driver and you will see data qualcomm usb driver i device manager .... this mean that totaly erased memory in tytn2 and its dead,only with jtag can flash again.
Please, tell me how can y do it. I have the same problem....
Step 3: Flash Hard-SPL (but the screen goes white then i boot the phone manually by pressing camera button) after done.
Click to expand...
Click to collapse
I don't see any step about using the white screen fix so I'm guessing you didn't successfully install HardSPL and then after that you tried flashing a ROM whilst being oblivious to the fact that Hard SPL wasn't installed, so you most likely bricked your phone
AllTheWay said:
huh. I don't have to hold down the power button to enter the bootloader. I just hold down the camera button and put the stylus into the reset hole.
Click to expand...
Click to collapse
Dead HTC KAISER
Hello My friends
After along search and Googling on the net without finding any solution. at last I did took a Risk to solve and save my DEAD HTC KAISER . what i did is I ressembled the HTC KAISER , to see if my USB data input was defect, but it was Good, now .......he he.. what i fond avery smal Batterie planted on the motherboard , i took it of the the board , end waited 1 hour . then i place it back , assembeled my HTC KAISER back
Taaaaraaaaa my HTC KAISER Power Led went ON ,,, YES ..Friends . is charging .
after 1/2 hour , I swish the HTC on ,,,, heeeee Is working......flash it with the new ROM wm 6.5 ...really it went Perfect.. end My HTC KAISER... ALIVE AGAIN.
Greatins , and hoppe this will Help you..........Good Luck .
on youtube you can find videos how to dissembele your HATC KAISER.
thanks to XDA-Developers , for this great Forum.
ericc191 said:
If you cant get it into boot loader mode, ur gonna have a lot of trouble trying to fix it. Like everyone has said so far... Press and hold both the Power button and Camera button together and then use your stylus to soft reset it.
Click to expand...
Click to collapse
my kaiser boots up but after the att thing the screen gos black do you know how to fix this
Hello all,
Yesterday I installed Firefly 2.7 on my Canadian Samsung Captivate. Everything worked fine except that I could not receive calls (when I did I lost connection and it hung up right away without me having the time to do anything).
What I did tonight is I tried to reinstall the stock firmeware found somehwere in here. I followed the instructions which asked me to instal it using Odin3 v1.7 which I did. What happened though is that right after I clicked start button in Odin, the installation failed so I was left with an incomplete install.
I was stuck in download mode and could not do anything with my device and my phone would not reboot so I removed the battery. Now I can't boot my phone no matter what I do, I can't connect it to the computer either. I tried the button combination to go in download mode (remove the battery, wait, press vol+ and - and power, connect the phone to pc, put the battery back in, take my finger of the power button) and nothing. No matter what I do or try my phone is not doing anything. It is turned off and it stays that way.
Is my phone now a piece of garbage ? Any idea what I could do ?
Thx in advance ...
[Q] Unable to flash Lenovo A660 -> looped during factory reset -> unable to boot
Hello all!
I am having a really strange error with my phone. I can't flash it. Even when it says it's "Downloaded OK" -> green circle in Smart Phone Flash Tool, seems like nothing really happened.
The problem is, machine Lenovo A660 keeps restarting and "updating". Lenovo logo -> Android image with some weird blue shape -> restart. (5-10secs each repetition).
My Factory mode looks like this -> http://imageshack.us/photo/my-images/594/img5854y.jpg/ (power on + volumne down)
This phone came with Etotalk MOD ROM.
Main problem occured, when I've couldn't access my applications -> Application not found error and lost all application icons. Then Google Play said, my account has never been used with this device. So I joined again, "re"installed applications. Some worked, but most of them kept shutting down with errors. So I decided for factory reset via software menu recovery and backup menu (??). Device started to "recovering" and it was doing for 20-30minutes - so I have restarted it.. bearing on mind, that factory reset did not work, as people stated it lasts around 7mins..
Then I have tried to flash it using various boot.img and recovery.img from
http://forum.xda-developers.com/showthread.php?t=1874403 and http://forum.xda-developers.com/showthread.php?t=2104748
but they won't work. Seems like something starts earlier then true recovery tool.
Any help would be appreciated.
Thank you in advance.
Mich
I have found and use stock-modded ROM for this phone, but it really seems like Smart Phone Flash Tool is not flashing this device.
The thing is, I never see that purple bar to come.
I am using only recovery and boot image. After hitting Download I connect phone, which got battery out for few secs, and leave it as is. Red bar fills up, yellow bar fills up and that all, green circle appears.
When I start device, no change has happened. :-/
Somebody help me, please..
Btw, what is that THL and which is on my phone? Do I actually need it?
I am really stuck.
Michalxo said:
If you would have some spare time, would you help me please?
This is my problem described in a deeper way -> http://forum.xda-developers.com/showthread.php?p=37983752
I think, that smart phone flash tool is not actually flashing the device at all.
Your help is probably the last I might get.. in case you know any other phone-expert.
I had this phone for almost a month and a week
PS: I have anohter exactly same phone in case it might help something in something.
Thank you very much in advanced.
Mich
Click to expand...
Click to collapse
You are correct, the standard recovery will not flash the ROM. You *must* first flash a custom recovery using the windows flash utility, and after that you can flash the ROM you linked to.
Read the first two posts in this thread, and the pages it links to, especially the two 'flash' links and the A660 recovery link.
cybermaus said:
You are correct, the standard recovery will not flash the ROM. You *must* first flash a custom recovery using the windows flash utility, and after that you can flash the ROM you linked to.
Read the first two posts in this thread, and the pages it links to, especially the two 'flash' links and the A660 recovery link.
Click to expand...
Click to collapse
Thank you for your help! After some hard battling with some button combinations I managed to get into some "etotalk" rom recovery, which fixed partitioning (using mke2fs tool) and getting clean "old" 4.0.4 android.
Thank you again! Phone is alive!
PS: I am not sure of the combination, but I pressed & hold both volume controls and simultaneously (or few ms later) pressed power on button.
Michalxo said:
Hello all!
I am having a really strange error with my phone. I can't flash it. Even when it says it's "Downloaded OK" -> green circle in Smart Phone Flash Tool, seems like nothing really happened.
The problem is, machine Lenovo A660 keeps restarting and "updating". Lenovo logo -> Android image with some weird blue shape -> restart. (5-10secs each repetition).
My Factory mode looks like this -> http://imageshack.us/photo/my-images/594/img5854y.jpg/ (power on + volumne down)
This phone came with Etotalk MOD ROM.
Main problem occured, when I've couldn't access my applications -> Application not found error and lost all application icons. Then Google Play said, my account has never been used with this device. So I joined again, "re"installed applications. Some worked, but most of them kept shutting down with errors. So I decided for factory reset via software menu recovery and backup menu (??). Device started to "recovering" and it was doing for 20-30minutes - so I have restarted it.. bearing on mind, that factory reset did not work, as people stated it lasts around 7mins..
Then I have tried to flash it using various boot.img and recovery.img from
http://forum.xda-developers.com/showthread.php?t=1874403 and http://forum.xda-developers.com/showthread.php?t=2104748
but they won't work. Seems like something starts earlier then true recovery tool.
Any help would be appreciated.
Thank you in advance.
Mich
Click to expand...
Click to collapse
hi i have the same problem with the same phone,how you solved the problem?
thank you
nicodim23 said:
hi i have the same problem with the same phone,how you solved the problem?
thank you
Click to expand...
Click to collapse
This might no longer be up to date AND I am no expert but when I was "playing" with my A660, I noticed that some (generic) descriptions for flashing, etc. refer to up- and down volume buttons, which (because they are on the right side of the device?) are in some cases mirrored to some of the instructions. In other words, up is down and down is up (if that makes sense).
If I power off the device, I usually first press volume up (and keep it pressed), while then also pressing and holding the power button.
Once the screen comes to live, you may let go of the buttons.
This combination brings me into the CWM Recovery based Recovery Mode. My phone also had the ETOTALK ROM installed ...
Navigation is with volume up / down and item selction is with the power button!
Same procedure with volume down gets you into the "factory Mode" menu, where you can do all sorts of test. However, this mode is also required for some (!) flashing procedures (ofter referred to for adb access).
Scrolling through the entries with volume down. Accepting an entry with Volume Up!
Hope this helps,
Robert
New Lenovo A660
Hallo, I root'ed my new phone with A789_ROW_S106_cybermaus_ICS_V3.1 with SP flash tool.
Every thing was working great until I want to instal v3.21.
I flashed the old v3.1 and I have a problem.
My phone don't power on, but I can flash booting, rocovery.img etc, what can I do to make it working again ??
Now, I see phone in SP FLASH TOOL, I can flash booting, recovery, but phone won't power on.
Is there anything i can do??
DawidMacha said:
Hallo, I root'ed my new phone with A789_ROW_S106_cybermaus_ICS_V3.1 with SP flash tool.
Every thing was working great until I want to instal v3.21.
I flashed the old v3.1 and I have a problem.
My phone don't power on, but I can flash booting, rocovery.img etc, what can I do to make it working again ??
Now, I see phone in SP FLASH TOOL, I can flash booting, recovery, but phone won't power on.
Is there anything i can do??
Click to expand...
Click to collapse
What phone were you flashing?
please with with my lenovo a660
steirx said:
This might no longer be up to date AND I am no expert but when I was "playing" with my A660, I noticed that some (generic) descriptions for flashing, etc. refer to up- and down volume buttons, which (because they are on the right side of the device?) are in some cases mirrored to some of the instructions. In other words, up is down and down is up (if that makes sense).
If I power off the device, I usually first press volume up (and keep it pressed), while then also pressing and holding the power button.
Once the screen comes to live, you may let go of the buttons.
This combination brings me into the CWM Recovery based Recovery Mode. My phone also had the ETOTALK ROM installed ...
Navigation is with volume up / down and item selction is with the power button!
Same procedure with volume down gets you into the "factory Mode" menu, where you can do all sorts of test. However, this mode is also required for some (!) flashing procedures (ofter referred to for adb access).
Scrolling through the entries with volume down. Accepting an entry with Volume Up!
Hope this helps,
Robert
Click to expand...
Click to collapse
I also had exactly the same problem as you, when trying to do a factory reset on my phone too. the vol up+ power button don't work, instead the phone starts in the same looped state, displaying the green android logo & restarting.
somebody please help me out.
DawidMacha said:
.....
My phone don't power on, but I can flash booting, rocovery.img etc, what can I do to make it working again ??
Now, I see phone in SP FLASH TOOL, I can flash booting, recovery, but phone won't power on.
Is there anything i can do??
Click to expand...
Click to collapse
I have the same end result (after a factory reset (unintended) and unsuccesful attemts to put etotalk recovery rom back) i did a "format" from the flash tool): the phone appears dead, it will not power up. the flash tool does recognise the phone, and will download, memory test (it does say: "NAND Flash was not detected" however), etc.
Henkjan_O said:
I have the same end result (after a factory reset (unintended) and unsuccesful attemts to put etotalk recovery rom back) i did a "format" from the flash tool): the phone appears dead, it will not power up. the flash tool does recognise the phone, and will download, memory test (it does say: "NAND Flash was not detected" however), etc.
Click to expand...
Click to collapse
solved!
using the instructions from http://forum.xda-developers.com/showthread.php?t=1943442 I got the phone unbricked, so I could put the original firmware back (thanks to etotalk tech support for that tip) and then upgrade again tothe etotalk ROM.
Hey ppl.
I got a Nexus S and his power button does not work for a week now. Since i got it still on warranty i decided to get it to samsung service.
I was using SlimBean so it was ok with volume rocker as a wake the device action. Since Samsung wanted the phone to be stock and locked i decided to do it. I found the stock rom, i flashed it, and here is when the problem started. I flashed the rom the way i flashed every other "custom" rom, via ClockWorkMod. Then, trying to also lock the bootloader i found this. I installed the device drivers again etc etc and when the program says "Checking Fast Boot Status" everything stops. The phone is not responding (can't move up and down with volume roker) and i have to pull the battery to reset it. Thankfully when i put the battery back in the phone starts up itself so no need for power button
So what can i do? Whats wrong with my bootloader?? Is there any way to install a custom recovery again, to have a rom with volume key unlock and leave the power button as it is? (reminder : phone is back to stock and no superuser, cwm or anything)
Appreciate any help !
Please help!
Hello! This is a distress call, because I think I brickered my S10e, through my own fault ...
Trying to install the TWRP according to the instructions given in the Hades Rom, I made two unforgivable mistakes, since years of flashing roms ...
1) I took the wrong installation file (I have the G970F/DS, and flash the beyond2lte file, instead of beyond0lte)
2) I omitted to force boot of TWRP just flashed.
Result: I cannot enter download mode as I did before (the phone does not blink), and trying to enter recovery, out of 20 attempts, it only turned on 2 times and does not go beyond the warning screen that the oem is unlocked, and it is not a safe state. I press power to continue as it says, and the screen turns off. Of course it doesn't start normally with the power button either.
I found out recently that been connected to the PC, it is recognized by it, and I even could access to it though the Windows explorer... Ergo, it's not dead, but the screen is in the infamous "black screen of death". Tried the usb jig emulator, by sugestion of denon480, but it didn't work (see screen capture).
Is there a way to force it into download mode, to flash the correct recovery, or eventually an official firmware? The cell phone is immaculate, I can not resign myself to it turns paperweight !!!!!
I put this here, because the problem was in TWRP recovery flashing, I didn't arrived to the Hades ROM installing process, and this way I can reach more people...
I appreciate any help.
Cheers
https://1drv.ms/u/s!Aqmv5IkqbGj3mwqTWmEd3VJxPPHs?e=V3UVSP
I don't even think it is possible to brick Samsungs like that. Are you following the right steps to download mode? Ergo,
Step 1 – Turn OFF your Galaxy S10.
Step 2 – Now press and hold the following buttons on your phone together: Volume Down + Bixby Button.
Step 3 – Next, plug in one end of the USB-C cable to a computer and the other end to the phone. As soon as you will connect, your phone will power on.
I have the same problem. I do not know if the OEM unlocking has something to do with that as I can not turn on OEM although it is not missing but it is not active and can not be turned on. I tried all the solution available online but it looks like no one knows what to do even the so called experts know nothing at all and the only things they know is the direct easy way. So disappointed
Same problem here... any solutions?