AFTER UNLOCK NO VOICE OR SPEAKER WORKING I JUST FLASHED WITH
(RUU_Kaiser_HTC_WWE_1.25.405.0_22.39.82.00.b_1.27.04.15_Test) NOW PHONE DOESNT
POWER UP OR BOOT MODE BLANK SCREEN
I TRY TO CONNECT TO THE COMPUTER ASKING DRIVER (DATE INTERFACE)
I NEED YOUR HELP TO GET BACK LIVE
PLEASE
THANKS
How did you unlock it? Did you CID unlock? HardSPL version? Can you get to the bootloader by holding down the camera button and power button and soft reset at the same time?
From the sound of things you loaded a CID locked rom onto your locked phone. This is only a guess though based on the fact that the ROM you loaded included a compatible radio.
Just a tip, next time don't use all caps. It's considered shouting and inappropriate. We understand your urge to get it fixed so we'll help even without the caps
Answering Alibaba0101's questions will help a lot. Also, have you tried taking the battery out and putting it back in?
The phone was on orange.
Step 1: install JumpSPL1.93-KAIS.exe
Step 2: Run KaiserUnlocker.exe (PolarisUnlocker)
Step 3: Flash Hard-SPL (but the screen goes white then i boot the phone manually by pressing camera button) after done.
Step 4: Run unlock Radio (take couple of mint and done and phone reboot)
Step 5: Run Unlocker ( after run unlocker i get 2 option unlock and super cid 000000 and I click checked both option and press okay its take less then 1 mint done.
Step 6: i take it out battery from the phone put different sim card and power on the phone phone was unlocked when I dial help line i didn’t get any sound. No speaker no ear sounds.
then i flashed (RUU_Kaiser_HTC_WWE_1.25.405.0_22.39.82.00.b_1.27. 04.15_Test) and after done flash phone dead screen blank I try to boot the phone by pressing camera button but phone not responding after connect the usb to phone get msg (DATA INTERFACE) driver.
Phone still dead i try to put another battery but still same I did try soft reset hard reset but still dead
Please help
THANKS
lxa786 said:
The phone was on orange.
Step 1: install JumpSPL1.93-KAIS.exe
Step 2: Run KaiserUnlocker.exe (PolarisUnlocker)
Step 3: Flash Hard-SPL (but the screen goes white then i boot the phone manually by pressing camera button) after done.
Step 4: Run unlock Radio (take couple of mint and done and phone reboot)
Step 5: Run Unlocker ( after run unlocker i get 2 option unlock and super cid 000000 and I click checked both option and press okay its take less then 1 mint done.
Step 6: i take it out battery from the phone put different sim card and power on the phone phone was unlocked when I dial help line i didn’t get any sound. No speaker no ear sounds.
then i flashed (RUU_Kaiser_HTC_WWE_1.25.405.0_22.39.82.00.b_1.27. 04.15_Test) and after done flash phone dead screen blank I try to boot the phone by pressing camera button but phone not responding after connect the usb to phone get msg (DATA INTERFACE) driver.
Phone still dead i try to put another battery but still same I did try soft reset hard reset but still dead
Please help
THANKS
Click to expand...
Click to collapse
I don't see the step where you flashed your original radio back after doing the SIM unlock. The radio that you is a special "patched" radio, and the phone will not successfully boot into Windows with it flashed.
Go into the bootloader (hold Camera during power on), and flash a compatible radio. If you haven't flashed a cooked ROM yet, then just hit up the Kaiser Wiki and grab the original ship radio for your phone.
Bootloader is entered by holding the power button and camera button down while soft resetting the phone. (sticking the styles in the hole) Keep holding the 2 buttons down until your in bootloader. Even with the wrong radio the phone should still go into bootloader properly
austinsnyc said:
Bootloader is entered by holding the power button and camera button down while soft resetting the phone. (sticking the styles in the hole) Keep holding the 2 buttons down until your in bootloader. Even with the wrong radio the phone should still go into bootloader properly
Click to expand...
Click to collapse
huh. I don't have to hold down the power button to enter the bootloader. I just hold down the camera button and put the stylus into the reset hole.
Boot Loader
Same here I just hold down camera button and soft reset works every time.
hi I need your more help how can I get phone on boot mode phone dead not responding I tried more then 10 time by pressing camera and power button phone still blank screen.
No display show so how can I flash the phone
Any idea to flash the phone dead mode?
thanks
If you cant get it into boot loader mode, ur gonna have a lot of trouble trying to fix it. Like everyone has said so far... Press and hold both the Power button and Camera button together and then use your stylus to soft reset it.
This has gotten people in the past, so sorry if it sounds dumb.
The Camera button has two settings Full Press and Half Press. Press until it stops then press again. You need to be pushing the Camera Button down all the way to get into Bootloader.
Also I never need to press the power Power Button As well.
I may be wrong but, when the phone is on, you can press the Camera and Soft Reset buttons. When the phone is off, you press the Power, Camera, and Soft Reset buttons to go directly into boot loader.
i tried but screen still blank no light nothing when i put usb into the phone asking driver (data interface)?
Can not go in bootloader help?
Tytn 2 is dead .
Ok last night I try to install the new hyperdragon III BlackStone rom everything is fine untill it finish and it cant load in to window, the computer keep asking me for the data interface and the tilt keep restart and the screen only shows hyperdragen III. I was running hyperdragon III opal (10/11/08) I tried MMTY and reinstall the OE rom but no luck, please help!!
Tytn2 Dead or not??
Tytn 2 is dead if you see data interface driver when put in usb cabel install v3 motorola driver and you will see data qualcomm usb driver i device manager .... this mean that totaly erased memory in tytn2 and its dead,only with jtag can flash again.
Please, tell me how can y do it. I have the same problem....
Step 3: Flash Hard-SPL (but the screen goes white then i boot the phone manually by pressing camera button) after done.
Click to expand...
Click to collapse
I don't see any step about using the white screen fix so I'm guessing you didn't successfully install HardSPL and then after that you tried flashing a ROM whilst being oblivious to the fact that Hard SPL wasn't installed, so you most likely bricked your phone
AllTheWay said:
huh. I don't have to hold down the power button to enter the bootloader. I just hold down the camera button and put the stylus into the reset hole.
Click to expand...
Click to collapse
Dead HTC KAISER
Hello My friends
After along search and Googling on the net without finding any solution. at last I did took a Risk to solve and save my DEAD HTC KAISER . what i did is I ressembled the HTC KAISER , to see if my USB data input was defect, but it was Good, now .......he he.. what i fond avery smal Batterie planted on the motherboard , i took it of the the board , end waited 1 hour . then i place it back , assembeled my HTC KAISER back
Taaaaraaaaa my HTC KAISER Power Led went ON ,,, YES ..Friends . is charging .
after 1/2 hour , I swish the HTC on ,,,, heeeee Is working......flash it with the new ROM wm 6.5 ...really it went Perfect.. end My HTC KAISER... ALIVE AGAIN.
Greatins , and hoppe this will Help you..........Good Luck .
on youtube you can find videos how to dissembele your HATC KAISER.
thanks to XDA-Developers , for this great Forum.
ericc191 said:
If you cant get it into boot loader mode, ur gonna have a lot of trouble trying to fix it. Like everyone has said so far... Press and hold both the Power button and Camera button together and then use your stylus to soft reset it.
Click to expand...
Click to collapse
my kaiser boots up but after the att thing the screen gos black do you know how to fix this
Related
So i just flashed my vox with dr.gonzo's new 1.0 rom...and I did it the same way i've been doing it for months now (since his first rom 0.1) and it all went good, but when it was suppose to reboot turned off but never turned back on....I turn it on manually and i see the htc logo, it vibrates and then black screen... nothing happens afterwards...please dont tell me its bricked...please.....
If you're not able to get it into the bootloader to run an RUU then I suggest that you flash a signed HTC ROM, flash USPL and then re-flash New Guava v1.0
how do i flash a signed htc rom? when i turn it on, the htc logo comes on, then vibrates, and then a black screen.... when i try a hard reset, it asks me to confirm by pressing send. i press send (correct me if i'm wrong, send is the green 'phone' button right?) and it loads up the htc logo, vibrates and then shuts off. I've never had a bricked phone before, this all just doens't make sense i did the same steps that i've always done.
Seriously? Your phone is not bricked.
If you've flash a ROM before, it's the exact same procedure - what you can try and do is load into the bootloader by holding the camera button and plugging in a USB cable, it will start into the tri-color screen and should show USB is connected then you can flash a signed HTC ROM.
If the ROM is corrupt, this is your best way of "recovering" your phone, if the ROM was flashed properly, after getting into the bootloader, run ruurun 0 and ResetDevice to boot it back into OS.
oh ok, i haven't tried that yet (bootloader mode that is). Now you say i do this by plugging the usb and holding the power button and camera button? is that how it works? h4waii, you just lightened up my day by giving me some hope!
That is how you can enter the boot loader.
1). Turn off and unplug the Vox from external power/USB cable
2). Press and hold the camera button
3). Insert external power/USB cable
4). Continue to hold camera button until you enter the tri-color screen
At this point, you should have a "USB" text label on the bottom left hand side indicating USB is detected - you can then run an RUU from a signed HTC ROM to update it.
press and hold the camera button alone? i tried that, it doesn't power up the unit though?
Yes it does. Hold camera and plug in your USB cable (making sure it's also plugged into your computer).
ok i got it to the triband screen, but when i ran dr.gonzo's rom it got to 3% and said its corrupt. so i'm gonna do what you said and flash a signed htc rom. hopefully it works....
Yes, 3% because SPL is not patched to allow an unsigned ROM to be loaded, flash an HTC ROM to it, once that is complete you can run USPL to re-flash New Guava.
It will work, don't need to hope
you are a godsend! literally have no idea how depressed i was yesterday! being a university student money is very tight right now so was a total shock when i realized i bricked my $350 phone....I wish i had money cause i'd send you some for being so helpful but I dont... So just please understand i REALLLY appreciate your help, thank you.
That's what we're here for. Glad to be of service.
Hi,
Newbie here....A pola200 came to me for password...incoming and outgoing call working..how ever there is a password..wats the best way to remove the password...Or how do i go abt hard resetting it
Thanks in advance
cliffrock
Well as i see there is no one answering me the question....
I found my own solution:
Hard Reset:
On the 02 Orbit2, make sure the phone is powered on and then press AND HOLD the Windows and OK buttons down at the same time, THEN use your stylus to press AND RELEASE the reset button (while you CONTINUE to hold down the Windows and OK buttons). You should get a grey-ish/white screen explaining how to complete the hard reset or how to cancel the operation.
If you cannot see anything on your screen due to the OS being totally messed up (in other words, as long as it's not hardware failure), then you need to put your device into bootloader mode (4-color screen) so that you can flash the ROM (either what you already are using, or a newly cooked one - either way you need to have a ROM image file on your computer to complete the flashing process).
Bootloader Mode:
To enter bootloader mode, press AND HOLD the camera button and then press AND RELEASE the soft reset with your stylus. When the screen is showing the 4 color bands, plug in the USB cable between your computer and phone flash the ROM.
Click to expand...
Click to collapse
Br
cliffrock
Thanks man, working good.
Very thanks
Hello, well, after several searching ended up here... my first post (like all of us when in trouble)
When trying to enter the tri-color screen, we pressed several times power+volume down and reset button but the phone never gets there, no matter what you do and now it is stuck at the "boot" screen that says: "Touch pro" in white letters and in the right down corner, with red letters says:
R 1.02.25.19
G 52.33.25.17W
D 1.94.00.00
Now, what to do here? it doesn´t boot, no hard reset, no nothing, if i press the reset button re-powers and gets there again... help..!!!
Thanks.
Sergio.
squiros1976 said:
Hello, well, after several searching ended up here... my first post (like all of us when in trouble)
When trying to enter the tri-color screen, we pressed several times power+volume down and reset button but the phone never gets there, no matter what you do and now it is stuck at the "boot" screen that says: "Touch pro" in white letters and in the right down corner, with red letters says:
R 1.02.25.19
G 52.33.25.17W
D 1.94.00.00
Now, what to do here? it doesn´t boot, no hard reset, no nothing, if i press the reset button re-powers and gets there again... help..!!!
Thanks.
Sergio.
Click to expand...
Click to collapse
Do entering bootloader : http://wiki.xda-developers.com/index.php?pagename=Raphael_For_Beginners#bootloader (With the device turned off, press and hold the VOLUME DOWN and POWER buttons, then press the RESET button with the stylus)
Then flash new ROM, i hope it's helping
Already tried that...
erwinpiero said:
Do entering bootloader :
(With the device turned off, press and hold the VOLUME DOWN and POWER buttons, then press the RESET button with the stylus)
Then flash new ROM, i hope it's helping
Click to expand...
Click to collapse
That´s exactly why i ended with the phone stuck at the first time... i recently got this phone and i wanted to see the bootloader version and stuff to do a firmware update but now it´s just there all the time. Not even being recognized by the pc.
Thanks.
Had You try flash via SD Card?
erwinpiero said:
Had You try flash via SD Card?
Click to expand...
Click to collapse
Well, no, i don´t have an sd card available now... one thing i forgot to say is the phone, after it is on that screen, never turns off again unless you remove the battery... and yes, i have left it on for a day, same thing...
What is the procedure to do the sd card flash thing? it that needs to get to the tree-color screen forget it... that´s exactly what the phone doesn´t do...
Thanks.
Sergio.
Hello Sir, to flash using SD card, you can read it here http://forum.xda-developers.com/showthread.php?t=448008 see number 5.
HTC Fuze
I had the same problem. None of the hard resets worked on my phone. The screen would be stuck on my lock screen and unresponsive. It would not shut off unless the battery was taken out.
Now it's working fine, all I had to do was press the reset button and enter in the code a1b2c3.
Hope this helps.
nessab04 said:
I had the same problem. None of the hard resets worked on my phone. The screen would be stuck on my lock screen and unresponsive. It would not shut off unless the battery was taken out.
Now it's working fine, all I had to do was press the reset button and enter in the code a1b2c3.
Hope this helps.
Click to expand...
Click to collapse
Hi,
Interesting... i´m not the only one with that problem then.... code doesn´t do anything... still same screen....
...no bootloader...
erwinpiero said:
Hello Sir, to flash using SD card, you can read it here --- see number 5.
Click to expand...
Click to collapse
Hello,
Ok, well, the main problem here is that i can´t get into bootloader... the phone is stuck at the fist "Touch pro" screen and nothing else happens...
Anyone with a clue on this? is this phone bricked then...
you sure youre puttin it into bootloader correctly? these things are pretty hard to brick, and can be put through hell and back and still be able to put into bootloader. make sure the hold VOLUME DOWN + POWER, and at the same time RESET WITH THE STYLUS IN THE BOTTOM...youll want to HOLD ALL THREE untill you see the tri colour bootloader screen. keep trying mate, it should go
Finally got bootloader...
the-wrangler said:
you sure youre puttin it into bootloader correctly? these things are pretty hard to brick, and can be put through hell and back and still be able to put into bootloader. make sure the hold VOLUME DOWN + POWER, and at the same time RESET WITH THE STYLUS IN THE BOTTOM...youll want to HOLD ALL THREE untill you see the tri colour bootloader screen. keep trying mate, it should go
Click to expand...
Click to collapse
Finally, after several tries it got into bootloader... now the thing doesn't end here because for some reason when i try to upload the Raphael Hard_SPL the phone goes ok to 0% and in about a minute a communication error appears and that's it...
We are moving forward... at least.
Bootloader Info.
Tried to flash via microSD but the phone says not allow..i guess that's because the hard SPL is not installed and it has the stock... here's what the bootloader shows, i'm not being able to install olinex hardSPL...
RAPH100
SPL-1.94.0000
MicroP-Raph (LED) v13
MicroP-Raph (KEY) v5
PSOC-Raph STAGE_CVT v0x36
PCBID 0x80
RID 0x0
ideas?
...no way to flash it back....
so... i guess there´s no way to get this back into business... when trying to flash always reports communication error at 0%...
You HAVE to flash hard spl off of a pc-it won't work flashing off an sd card (ever, no matter what you try), and I've heard you can run into problems (brick-type ones) trying to flash it off an sd card. It requires a special ruu to run. This is why it's packaged with the ruu, and you're told to only use that ruu for flashing hard spl.
I'm not sure why you're pressing power when trying to go into bootloader. All you need to do is press and -get this- HOLD DOWN volume down and then soft reset with your stylus. You can even press and hold volume down and do a software soft reset. I've used voice command to activate a soft reset shortcut in my start menu, and having vol down pressed sends you right into bootloader. Release volume down only when the tricolor screen appears. You don't need to hold down the reset button with the stylus. Just tap it and you're done.
Farmer Ted said:
You HAVE to flash hard spl off of a pc-it won't work flashing off an sd card (ever, no matter what you try), and I've heard you can run into problems (brick-type ones) trying to flash it off an sd card. It requires a special ruu to run. This is why it's packaged with the ruu, and you're told to only use that ruu for flashing hard spl.
I'm not sure why you're pressing power when trying to go into bootloader. All you need to do is press and -get this- HOLD DOWN volume down and then soft reset with your stylus. You can even press and hold volume down and do a software soft reset. I've used voice command to activate a soft reset shortcut in my start menu, and having vol down pressed sends you right into bootloader. Release volume down only when the tricolor screen appears. You don't need to hold down the reset button with the stylus. Just tap it and you're done.
Click to expand...
Click to collapse
ya i just noticed the RAPH100 in his info he posted and the t7272 in the header..mines a RAPH800 and bootloader HAS to have vol + power..anyway, i remember having an issue with something similar with my old vogue..have you tried flashing the shipped stock rom back on? if not, try flashing the stock back on it and if it goes, then try the unlock afterwards. dont fret bud, someone here will get you sorted out
here, i found this as im not well versed in raph100s. its a chart with raph100 roms. im sure some must be shipped stock roms and may be worth a try. sorry i couldnt help more, like i said hopefully someone who knows your device better may be able to help
http://wiki.xda-developers.com/index.php?pagename=HTC_Raphael_WM6.1_ROMs
How about flashing official ROM via microSD card?
patrick_spd4u said:
How about flashing official ROM via microSD card?
Click to expand...
Click to collapse
Download the official rom, right click on the exe and extract it somewhere, you'll get several files, rename RUU_signed.nbh to raphimg.nbh, move it to the root of your sd card and you should be able to install it. It should contain splash screen, radio and os.
No way to flash HardSPL...
Hello, thank you for your help! in fact the volume down+reset works perfect to get into bootloader but every time i try to flash hardSPL or stock rom via USB it says "communication error" and the phone displays a 0% bar...
Windows7 is detecting it as HTC USB Sync.
Thanks..
Farmer Ted said:
You HAVE to flash hard spl off of a pc-it won't work flashing off an sd card (ever, no matter what you try), and I've heard you can run into problems (brick-type ones) trying to flash it off an sd card. It requires a special ruu to run. This is why it's packaged with the ruu, and you're told to only use that ruu for flashing hard spl.
I'm not sure why you're pressing power when trying to go into bootloader. All you need to do is press and -get this- HOLD DOWN volume down and then soft reset with your stylus. You can even press and hold volume down and do a software soft reset. I've used voice command to activate a soft reset shortcut in my start menu, and having vol down pressed sends you right into bootloader. Release volume down only when the tricolor screen appears. You don't need to hold down the reset button with the stylus. Just tap it and you're done.
Click to expand...
Click to collapse
...will try it again...
Hi
In fact the most close to the rom i had on that cell is ruu_signed_1.90.401.1_wwe, downloaded it and will try it again later using sdcard... one thing i wonder is the SPL version which is 1.94.00.00 on my phone.
Sergio.
freakzone said:
Download the official rom, right click on the exe and extract it somewhere, you'll get several files, rename RUU_signed.nbh to raphimg.nbh, move it to the root of your sd card and you should be able to install it. It should contain splash screen, radio and os.
Click to expand...
Click to collapse
Hello
I had HTC Diamond before and now i bought HTC Touch Pro.
It has original O2 rom and I am trying to flash a new one. But I cannot enter bootloader. I did Hard-SPL but since i cannot enter bootloader I cannot check if it was succesful or not. I tried all the button combinations (like vol down + enter + reset etc...) but it was unsuccesfull. And i even tried to copy EnterBootloader.exe to the phone and run it. But the screen just goes black and thats all. And when I was trying to do HARD-SPL the screen also went only black. I never seen the three color screen. Please help me!
Thanks
Moved as not ROM Development.
Well, you're probably doing it wrong. Hold volume down, then soft reset. Keep holding vol down until the tricolor screen appears. Don't hold the reset button down; just push it and release it.
Im doing it right. Im sure
so u re trying to flash via card or not, if you're trying to flash via PC dont forget to connect with active sync before, if you are trying to connect with SD card dont forget to do a clean format of it before
I remembered that I actually had the issue once (no idea why, it only happened on one rom about a year ago). Try doing a hard reset, then go into bootloader (instead of pushing vol up and re-booting). If that doesn't work, then start the boot process, and when it hits the alignment screen, try to go into bootloader.
Dear all,
I have two big problems!
1st on is that my phone HD2 won`t start. It just freeze on the white screen with HTC logo and ROM numbers.
2nd is that when I tried to put it in bootloader mode it won`t go. I tried to press down volume key and power key but it happen`s teh same like in the 1st paragraf.
Can you maybe help me???
Thanks in advance.
take the battery out and do a hard reset. Hold volume up and down at the same time and press power button.
I also tried to do that and nothing happens! It just show`s white screen with htc logo.
My HD2 won't go to bootloader tri color screen when I press and hold the VOLUME DOWN then Press and hold the POWER button, but the phone starts normaly.
I already flashed the HSPL3 and nothing wrong happened. But when I tried to check if the HSPL status, the bootloader don't work.
My HD2 is T-Mobile
rsimiao said:
My HD2 won't go to bootloader tri color screen when I press and hold the VOLUME DOWN then Press and hold the POWER button, but the phone starts normaly.
I already flashed the HSPL3 and nothing wrong happened. But when I tried to check if the HSPL status, the bootloader don't work.
My HD2 is T-Mobile
Click to expand...
Click to collapse
Rsimiao, any luck getting your phone into bootloader mode? I have the same problem.
Have same problem
my hd2 won t go in bootlaoder mode, impossible to see spl and wont be flash by hspl 3
impossible to hard reset it
its saying that sd card fail to copy something
is there a solution ??
no usb loading in bootlaoder
Hi I have problem with loading usb in bootlaoder mode.....
When I turn on the phone everything is ok working fine
I'm trying to put a new Rom but I cant because can not find usb
can anyone help me please.....
Dont go to Bootloader (Tricolor Menu)
Hello HD2 Experts,
yesterday i wanted to reboot my HTC HD2 with Android (SD) on it, and after this it hanging on the HTC logo and cant boot.
It goes only to the MAGLDR but not to the Bootloader ( Tricolor Menu) if i press VOLUME DOWN AND POWER...
I installed via USB FLasher on MAGLDR the Windows 7 Phone and it was working perfectly without problems (Just Wlan/Wifi dont working). After this i tried to install 5 different NAND Android on my HD2 and every of this is hanging on this HTC Logo!!! I am sure that all this 5 were working before this...
My Problems:
1. Cant install (NAND) Android.
2. Cant join to the BOOTLOADER (Tricolor).
3. On WIndows 7 PHone no WLAN working.
I'm done with the nerves!!! Can anybody help me?
Best Regards, Mike
Take bettery out, then try again
it will work
i tried EVERYTHING! but it dont help
and battery too!
Having the same problem I have SPL-3.03 HSPL & trying to downgrade to SPL 1.66 but won't go into Bootloader. I've tried an 8gb, 4gb & now 1gb card the file has been renamed in the root to LEOIMG.nbh but just get the tri colour screen. Pressing reset button & holding end call & Vol down button.
This is the right file to rename from HTC?
_HTC HD2_RUU_Leo_HTC_WWE_1.66.405.2_Radio_Signed_15.30.50.07U_2.06.51.07_Ship
Make sure you are not using the USB cable while trying to enter bootloder. I had the same problem, but once unplugged the cable all was fine.
I'm having a similar problem. I reflashed to the HSPL, no problem. I then used the Rom UPdate Utility, which claimed it had updated my ROM to version 2 (although it took a fraction of the 10 minutes, it said it would). When I now try to boot the phone to install the rest, doesn't matter how much I hold the power key (which I presume is the 'make call' key, as that powers the phone up), it refuses to do anything other than boot to the O2 Welcome screen. I'm noticing the replies aren't very helpful here. Is this what I can expect for the whole forum? As a newbie, I can't make posts on the developers forums, so I can't ask them if they've come across this before. It seems a bit pants, to be honest!
HTC HD2 won`t go in to bootloader mode
Junks666 said:
... now 1gb card the file has been renamed in the root to LEOIMG.nbh but just get the tri colour screen.
_HTC HD2_RUU_Leo_HTC_WWE_1.66.405.2_Radio_Signed_15.30.50.07U_2.06.51.07_Ship
Click to expand...
Click to collapse
Hi Junks,
The THREE COLOUR SCREEN is BOATLOADER this is FIRST BOOT LOADER or (I Think) the name is H-BOOT. You have to correct ROM for HTC HD2, but CMIIW the rom is for HTC HD2 T8585 (WWE) with 516 Internal Memory. Is your HD2 this Model or another Model famous with name TMOUS (T-Mobile Edition) with 1024 Internal Memory. I believed if you still have tricolor screen easier to "wake up" your phone.
Im haveing the same problems please someone help... a Demonoid invite code is all I have to offer here
DJ Legless said:
I'm having a similar problem. I reflashed to the HSPL, no problem. I then used the Rom UPdate Utility, which claimed it had updated my ROM to version 2 (although it took a fraction of the 10 minutes, it said it would). When I now try to boot the phone to install the rest, doesn't matter how much I hold the power key (which I presume is the 'make call' key, as that powers the phone up), it refuses to do anything other than boot to the O2 Welcome screen. I'm noticing the replies aren't very helpful here. Is this what I can expect for the whole forum? As a newbie, I can't make posts on the developers forums, so I can't ask them if they've come across this before. It seems a bit pants, to be honest!
Click to expand...
Click to collapse
Is your problem solved ? Hold power key (Red) (Hang Up key) and Volume Down key simultaneously. what is you see on the screen ? if its three color RGB ... you are safe. I will advise whats next.
cheers up
x1123 said:
Is your problem solved ? Hold power key (Red) (Hang Up key) and Volume Down key simultaneously. what is you see on the screen ? if its three color RGB ... you are safe. I will advise whats next.
cheers up
Click to expand...
Click to collapse
No that is not the problem I can not get into the bootloader at all, I use to do it before, so after trying the vol. Down key I tried useing many other combinations without any luck, its as if the default bootloader is gone!
kris29440 said:
No that is not the problem I can not get into the bootloader at all, I use to do it before, so after trying the vol. Down key I tried useing many other combinations without any luck, its as if the default bootloader is gone!
Click to expand...
Click to collapse
HD2 is most great device. what is actually happened. You can brief here what you did before and some background of your HD2, what u have flashed in and what is inside, the more clue probably will help others to point a good thing for you. If No boot loader is the device totally "death"
x1123 said:
HD2 is most great device. what is actually happened. You can brief here what you did before and some background of your HD2, what u have flashed in and what is inside, the more clue probably will help others to point a good thing for you. If No boot loader is the device totally "death"
Click to expand...
Click to collapse
I usely use SD Builds, but I installed DFT_LEO_MAGLDR113_DAF,HSPL4,MAGLDR_CWM_Recovery_v3.0.2.5_for_NexusHD2_135M,NexusHD2-Gingerbread_V2.7_NAND__Android-2.3.4__update and wifi-calling-htcleo-gb-20110518 ( Yes I just copy and paste the file names lol) My phone was working fine (Not sure about the bootloader/Tri-color screen) untill a few days ago my android build boots in safe mode I did find a remedy for that and thats by pressing and holding the Call (green), Home and Windows keys down while the android boots, but I have to do that all the time now. What I am trying to do is restore it back to fatory settings. Oh yeah BTW the AMAGLDR bootloader dose boot and also CWM Recovery but while In the aMAGLDR I have to hold the back key to press vol. up and down other wise it will keep moveing back to the top of the list (Its been like that sence I installed MAGLDR) but I do not have any problems with the vol up and down key in any other programs. I am also able to use USB Flasher and any other mode besides Windows Mobile Device Center (Windows 7). I also tried gettng into Sync by installing Windows phone 7 (witch installed fine with USB flash (Useing MAGLDR) but not luck with syncing back to WM6.
x1123 said:
Is your problem solved ? Hold power key (Red) (Hang Up key) and Volume Down key simultaneously. what is you see on the screen ? if its three color RGB ... you are safe. I will advise whats next.
cheers up
Click to expand...
Click to collapse
Hi. I've tried that combination of keys & I just get the O2 Welcome screen. The only key combination that works is when I power up with the Vol Down key held. I then get the tri-colour screen.
Don't know if this helps but.....
When I get the tri-colour screen, I have the following text:
PB81100 HX-BC
SPL-2.08.HSPL 8G XE
0X05
CotullaHSPL 0x40