So i just flashed my vox with dr.gonzo's new 1.0 rom...and I did it the same way i've been doing it for months now (since his first rom 0.1) and it all went good, but when it was suppose to reboot turned off but never turned back on....I turn it on manually and i see the htc logo, it vibrates and then black screen... nothing happens afterwards...please dont tell me its bricked...please.....
If you're not able to get it into the bootloader to run an RUU then I suggest that you flash a signed HTC ROM, flash USPL and then re-flash New Guava v1.0
how do i flash a signed htc rom? when i turn it on, the htc logo comes on, then vibrates, and then a black screen.... when i try a hard reset, it asks me to confirm by pressing send. i press send (correct me if i'm wrong, send is the green 'phone' button right?) and it loads up the htc logo, vibrates and then shuts off. I've never had a bricked phone before, this all just doens't make sense i did the same steps that i've always done.
Seriously? Your phone is not bricked.
If you've flash a ROM before, it's the exact same procedure - what you can try and do is load into the bootloader by holding the camera button and plugging in a USB cable, it will start into the tri-color screen and should show USB is connected then you can flash a signed HTC ROM.
If the ROM is corrupt, this is your best way of "recovering" your phone, if the ROM was flashed properly, after getting into the bootloader, run ruurun 0 and ResetDevice to boot it back into OS.
oh ok, i haven't tried that yet (bootloader mode that is). Now you say i do this by plugging the usb and holding the power button and camera button? is that how it works? h4waii, you just lightened up my day by giving me some hope!
That is how you can enter the boot loader.
1). Turn off and unplug the Vox from external power/USB cable
2). Press and hold the camera button
3). Insert external power/USB cable
4). Continue to hold camera button until you enter the tri-color screen
At this point, you should have a "USB" text label on the bottom left hand side indicating USB is detected - you can then run an RUU from a signed HTC ROM to update it.
press and hold the camera button alone? i tried that, it doesn't power up the unit though?
Yes it does. Hold camera and plug in your USB cable (making sure it's also plugged into your computer).
ok i got it to the triband screen, but when i ran dr.gonzo's rom it got to 3% and said its corrupt. so i'm gonna do what you said and flash a signed htc rom. hopefully it works....
Yes, 3% because SPL is not patched to allow an unsigned ROM to be loaded, flash an HTC ROM to it, once that is complete you can run USPL to re-flash New Guava.
It will work, don't need to hope
you are a godsend! literally have no idea how depressed i was yesterday! being a university student money is very tight right now so was a total shock when i realized i bricked my $350 phone....I wish i had money cause i'd send you some for being so helpful but I dont... So just please understand i REALLLY appreciate your help, thank you.
That's what we're here for. Glad to be of service.
Related
AFTER UNLOCK NO VOICE OR SPEAKER WORKING I JUST FLASHED WITH
(RUU_Kaiser_HTC_WWE_1.25.405.0_22.39.82.00.b_1.27.04.15_Test) NOW PHONE DOESNT
POWER UP OR BOOT MODE BLANK SCREEN
I TRY TO CONNECT TO THE COMPUTER ASKING DRIVER (DATE INTERFACE)
I NEED YOUR HELP TO GET BACK LIVE
PLEASE
THANKS
How did you unlock it? Did you CID unlock? HardSPL version? Can you get to the bootloader by holding down the camera button and power button and soft reset at the same time?
From the sound of things you loaded a CID locked rom onto your locked phone. This is only a guess though based on the fact that the ROM you loaded included a compatible radio.
Just a tip, next time don't use all caps. It's considered shouting and inappropriate. We understand your urge to get it fixed so we'll help even without the caps
Answering Alibaba0101's questions will help a lot. Also, have you tried taking the battery out and putting it back in?
The phone was on orange.
Step 1: install JumpSPL1.93-KAIS.exe
Step 2: Run KaiserUnlocker.exe (PolarisUnlocker)
Step 3: Flash Hard-SPL (but the screen goes white then i boot the phone manually by pressing camera button) after done.
Step 4: Run unlock Radio (take couple of mint and done and phone reboot)
Step 5: Run Unlocker ( after run unlocker i get 2 option unlock and super cid 000000 and I click checked both option and press okay its take less then 1 mint done.
Step 6: i take it out battery from the phone put different sim card and power on the phone phone was unlocked when I dial help line i didn’t get any sound. No speaker no ear sounds.
then i flashed (RUU_Kaiser_HTC_WWE_1.25.405.0_22.39.82.00.b_1.27. 04.15_Test) and after done flash phone dead screen blank I try to boot the phone by pressing camera button but phone not responding after connect the usb to phone get msg (DATA INTERFACE) driver.
Phone still dead i try to put another battery but still same I did try soft reset hard reset but still dead
Please help
THANKS
lxa786 said:
The phone was on orange.
Step 1: install JumpSPL1.93-KAIS.exe
Step 2: Run KaiserUnlocker.exe (PolarisUnlocker)
Step 3: Flash Hard-SPL (but the screen goes white then i boot the phone manually by pressing camera button) after done.
Step 4: Run unlock Radio (take couple of mint and done and phone reboot)
Step 5: Run Unlocker ( after run unlocker i get 2 option unlock and super cid 000000 and I click checked both option and press okay its take less then 1 mint done.
Step 6: i take it out battery from the phone put different sim card and power on the phone phone was unlocked when I dial help line i didn’t get any sound. No speaker no ear sounds.
then i flashed (RUU_Kaiser_HTC_WWE_1.25.405.0_22.39.82.00.b_1.27. 04.15_Test) and after done flash phone dead screen blank I try to boot the phone by pressing camera button but phone not responding after connect the usb to phone get msg (DATA INTERFACE) driver.
Phone still dead i try to put another battery but still same I did try soft reset hard reset but still dead
Please help
THANKS
Click to expand...
Click to collapse
I don't see the step where you flashed your original radio back after doing the SIM unlock. The radio that you is a special "patched" radio, and the phone will not successfully boot into Windows with it flashed.
Go into the bootloader (hold Camera during power on), and flash a compatible radio. If you haven't flashed a cooked ROM yet, then just hit up the Kaiser Wiki and grab the original ship radio for your phone.
Bootloader is entered by holding the power button and camera button down while soft resetting the phone. (sticking the styles in the hole) Keep holding the 2 buttons down until your in bootloader. Even with the wrong radio the phone should still go into bootloader properly
austinsnyc said:
Bootloader is entered by holding the power button and camera button down while soft resetting the phone. (sticking the styles in the hole) Keep holding the 2 buttons down until your in bootloader. Even with the wrong radio the phone should still go into bootloader properly
Click to expand...
Click to collapse
huh. I don't have to hold down the power button to enter the bootloader. I just hold down the camera button and put the stylus into the reset hole.
Boot Loader
Same here I just hold down camera button and soft reset works every time.
hi I need your more help how can I get phone on boot mode phone dead not responding I tried more then 10 time by pressing camera and power button phone still blank screen.
No display show so how can I flash the phone
Any idea to flash the phone dead mode?
thanks
If you cant get it into boot loader mode, ur gonna have a lot of trouble trying to fix it. Like everyone has said so far... Press and hold both the Power button and Camera button together and then use your stylus to soft reset it.
This has gotten people in the past, so sorry if it sounds dumb.
The Camera button has two settings Full Press and Half Press. Press until it stops then press again. You need to be pushing the Camera Button down all the way to get into Bootloader.
Also I never need to press the power Power Button As well.
I may be wrong but, when the phone is on, you can press the Camera and Soft Reset buttons. When the phone is off, you press the Power, Camera, and Soft Reset buttons to go directly into boot loader.
i tried but screen still blank no light nothing when i put usb into the phone asking driver (data interface)?
Can not go in bootloader help?
Tytn 2 is dead .
Ok last night I try to install the new hyperdragon III BlackStone rom everything is fine untill it finish and it cant load in to window, the computer keep asking me for the data interface and the tilt keep restart and the screen only shows hyperdragen III. I was running hyperdragon III opal (10/11/08) I tried MMTY and reinstall the OE rom but no luck, please help!!
Tytn2 Dead or not??
Tytn 2 is dead if you see data interface driver when put in usb cabel install v3 motorola driver and you will see data qualcomm usb driver i device manager .... this mean that totaly erased memory in tytn2 and its dead,only with jtag can flash again.
Please, tell me how can y do it. I have the same problem....
Step 3: Flash Hard-SPL (but the screen goes white then i boot the phone manually by pressing camera button) after done.
Click to expand...
Click to collapse
I don't see any step about using the white screen fix so I'm guessing you didn't successfully install HardSPL and then after that you tried flashing a ROM whilst being oblivious to the fact that Hard SPL wasn't installed, so you most likely bricked your phone
AllTheWay said:
huh. I don't have to hold down the power button to enter the bootloader. I just hold down the camera button and put the stylus into the reset hole.
Click to expand...
Click to collapse
Dead HTC KAISER
Hello My friends
After along search and Googling on the net without finding any solution. at last I did took a Risk to solve and save my DEAD HTC KAISER . what i did is I ressembled the HTC KAISER , to see if my USB data input was defect, but it was Good, now .......he he.. what i fond avery smal Batterie planted on the motherboard , i took it of the the board , end waited 1 hour . then i place it back , assembeled my HTC KAISER back
Taaaaraaaaa my HTC KAISER Power Led went ON ,,, YES ..Friends . is charging .
after 1/2 hour , I swish the HTC on ,,,, heeeee Is working......flash it with the new ROM wm 6.5 ...really it went Perfect.. end My HTC KAISER... ALIVE AGAIN.
Greatins , and hoppe this will Help you..........Good Luck .
on youtube you can find videos how to dissembele your HATC KAISER.
thanks to XDA-Developers , for this great Forum.
ericc191 said:
If you cant get it into boot loader mode, ur gonna have a lot of trouble trying to fix it. Like everyone has said so far... Press and hold both the Power button and Camera button together and then use your stylus to soft reset it.
Click to expand...
Click to collapse
my kaiser boots up but after the att thing the screen gos black do you know how to fix this
here is my problem guys. i was trying to flash my htc touch 2 sprint it with Raphaelhardspl(wrong flashing) and in the process the screen went blank. i was trying to do it one more time and my PC is asking for qualcomm cdmd technologies msn driver, every time i connect the phone to my PC. i have tried it soft reset. and hard reset wont work. any suggestion will be thanks full. thank you. the main problem is that my pc wont recognize ??
WHOEVER solve my problem will pay 50 buck via paypal
The quickest way to brick your phone is to try to flash it with programs meant for other phones, which it appears you have done.( bricked )
Try putting it into bootloader and flashing stock rom , or try mtty.exe, but if your pc won't recognize it and your screen shows no life, it is probably toast. Does it at least have hardspl on it . ?
yes it does have hardspl. there have to be a way that my pc will recognized it. i think.
As denco7 said, have you tried getting into the bootloader mode?
Hold volume down and press the red button with your stylus.
Connect your pro2 to your PC and if it connects the word 'serial' will change into 'USB'.
If it does, your device is not bricked.
I suggest you flash Hard-SPL again, and make sure to follow the instructions exactly! Don't think you can do it just in a minute, just take your time.
Then flash another ROM by using MTTY (see here) and there you'll get some instructions.
Good luck!
it wont go to boot loader mode, when i connect it to the pc it begin to charge and noting happen , then suddenly the light go off and the pc detect a driver is missing quaccom etc. does any one know about that this driver.
I've had that before... that the MSM technology qualcomm **** is asking for a driver.
There's a driver replacement (used before mtty). You can try to install that; altough I don't think it will help.
If you can't get into bootloader your device is (probably) bricked.
What you can also try is getting your battery, sd-card and simcard out of your phone and leave it for an hour. Then put the battery only back, and try to boot.
Does your phone start when you press the start button? So do you feel a vibrate or somethin like that?
no it wont start but maybe by following that MTTY my pc read it, i will try it. . it doesn even bibrate it just that power light show when that phone its charging thats all.
thanks for you comment guys.
That's strange.
There's one last thing you could try: the ultimate hard-reset
Some time ago I bricked my diamond. I tried all available sofkey combinations.
Then, suddenly, my device vibrated like 3 tiimes very loudly.
It didn't still boot nor go into bootloader.
But after about 4 hours it booted!
I only don't know what the combination was... something like VOl UP + VOL DWN + lOCK BUTTON + RESET.
Just try some combinations, maybe it works for you.maybe not, but you could try it.
Hello
I had HTC Diamond before and now i bought HTC Touch Pro.
It has original O2 rom and I am trying to flash a new one. But I cannot enter bootloader. I did Hard-SPL but since i cannot enter bootloader I cannot check if it was succesful or not. I tried all the button combinations (like vol down + enter + reset etc...) but it was unsuccesfull. And i even tried to copy EnterBootloader.exe to the phone and run it. But the screen just goes black and thats all. And when I was trying to do HARD-SPL the screen also went only black. I never seen the three color screen. Please help me!
Thanks
Moved as not ROM Development.
Well, you're probably doing it wrong. Hold volume down, then soft reset. Keep holding vol down until the tricolor screen appears. Don't hold the reset button down; just push it and release it.
Im doing it right. Im sure
so u re trying to flash via card or not, if you're trying to flash via PC dont forget to connect with active sync before, if you are trying to connect with SD card dont forget to do a clean format of it before
I remembered that I actually had the issue once (no idea why, it only happened on one rom about a year ago). Try doing a hard reset, then go into bootloader (instead of pushing vol up and re-booting). If that doesn't work, then start the boot process, and when it hits the alignment screen, try to go into bootloader.
Dear All,
I tried to upgrade my HTC Hero from Andriod 1.5 to 2.1 . Everything was OK but last moment Upgradation went failed and Handset automatically shutdown. I tried to powered it up but no fruitfull result. I checked the battery by inserting in some other handset, It was OK. Thats mean there is no issue with battery. Handset doesnt show charging indication while connected to charger. I also tried to power it up in safe mode by pressing combination of keys but no result.
Kindly suggest solutions to power up HTC Hero. Thanks in advance.
is this a cdma hero or gsm hero?
you could try and fastboot usb and run the ruu again
It is GSM HTC HERO.......Please tell me way to do fastboot....Please Help
When I pressed HOME+POWER ON/END CALL button.........There is little vibration.....Nothing else
waiting for reply for some one.....Thanks
When I pressed HOME+POWER ON/END CALL button.........There is little vibration.....Nothing else
waiting for reply for some one.....Thanks
I tried to put handset in fastboot mode but no result...i pressed back+power for fastboot mode..............................waiting for further instruction
Do you get a vibration? If so download fastboot drivers and fastboot files. Try flashing a ROM using fastboot.
Donwload and install this first: http://forum.xda-developers.com/showthread.php?t=1126671
Download and extract these: http://forum.xda-developers.com/showthread.php?t=1055888
After the vibration, open CMD, cd to the folder where you extracted fastboot and type fastboot and then press enter. If you see your device listed in fastboot, download fastboot images for your phone and flash them.
I got vibration when i pressed home+power button.....I didnt get any response from my handset if i pressed back+power and volume down+power button...Please tell me can i do above procedure in this state...............................
Dear Nibras,
I tried the whole procedure but handset didnt power up. I want to explain the issue again to you, Handset doesnt show any thing when I press power button, LCD doesnt glow nor handset vibrate. Its Just like dead phone but when I pressed home+power button, it vibrates.
This Issue came, when I was just tried to upgrade it from Andriod 1.5 to 2.1, this upgradation failed due to some reason and after this handset is not powering up.
When I connected it with PC. PC doesn't recognize any hardware connect to it.
I need your help as my handset is out of warranty.
Thanks and Best Regards,
muqaddas_dunyatv said:
Dear Nibras,
I tried the whole procedure but handset didnt power up. I want to explain the issue again to you, Handset doesnt show any thing when I press power button, LCD doesnt glow nor handset vibrate. Its Just like dead phone but when I pressed home+power button, it vibrates.
This Issue came, when I was just tried to upgrade it from Andriod 1.5 to 2.1, this upgradation failed due to some reason and after this handset is not powering up.
When I connected it with PC. PC doesn't recognize any hardware connect to it.
I need your help as my handset is out of warranty.
Thanks and Best Regards,
Click to expand...
Click to collapse
I don't think I can help anymore. I guess the phone is bricked. Try connecting your handset to another PC and follow the same procedure.
Even if the handset is out of warranty, take it to Service Center and tell them your phone won't power up. Don't tell about the failed upgrade. If they could just reprogram the PCB, let them do it. If they say, they want to change the PCB/motherboard, forget it and get a new phone.
It's sad you waited this long to upgrade to 2.1. You should've done it during the warranty period.
Hi, I've got a little sceary problem with my desire s.
I installed reaper v 1.2 ROM, configured it, everything was ok. But now phone is not responding. Only black screen. I tried vol up/down and power button configuration - nothing happend. I connected phone to the charger and led turned on, I tred the same configuration - nothing happend. I discconnect phone - led is still on and phone is not responding.
I downloaded latest android sdk tools, latest htc drivers, installed, connected phone to computer, run sdk tool and type adb reboot recovery - error device not found.
When I connect phone to computer it found Qualcomm CDMA Technologies MSM, I try to install soft automaticly but comp find nothing.
Wha else I can do? I don't want pull battery. I have never done it.
Help, please.
adix631 said:
Hi, I've got a little sceary problem with my desire s.
I installed reaper v 1.2 ROM, configured it, everything was ok. But now phone is not responding. Only black screen. I tried vol up/down and power button configuration - nothing happend. I connected phone to the charger and led turned on, I tred the same configuration - nothing happend. I discconnect phone - led is still on and phone is not responding.
I downloaded latest android sdk tools, latest htc drivers, installed, connected phone to computer, run sdk tool and type adb reboot recovery - error device not found.
When I connect phone to computer it found Qualcomm CDMA Technologies MSM, I try to install soft automaticly but comp find nothing.
Wha else I can do? I don't want pull battery. I have never done it.
Help, please.
Click to expand...
Click to collapse
Don't panic brother. I've been in a similar situation many times. Whatever you do... DO NOT PULL THE BATTERY till the phone is switched off!!
Just disconnect the phone from the laptop or wall socket (remove the usb cable from the phone) and leave the phone. Don't sit and stare at it, and don't try to reason it into rebooting. Also, stop pestering God...he doesn't do phones. (I think) Just relax, and go watch T.V. or something.
One out of two things may happen :
1. It may reboot on it's own. Has happened to me... Sometimes it happes in 5 mins, sometimes in 20, and sometimes, never.
2. The battery will eventually run out of charge and your phone will switch off by itself. Now remove the battery, reinsert after 2 mins and boot up into recovery. From here, you can restore your previous nandroid backup.
P.S. If you do not have a nandroid backup, just reflash the ROM after a full format ("format all partitions, except sdcard" option in recovery). Note that if you have unlocked using HTC site, this will not work until you manually flash boot.img (you can find it in the ROM (Reaper_v1.2.zip) file) from fastboot.
Let me know what happens.
Now I' still waiting, without phone touching. Led is ON (orange colour). Phone is disconected (and me too ). Battery level was 13% before this insydent.
When LED will turn off (I don't know when) I'll reinsert battery and let you know what's up.
I hope, I did't bricked it...
adix631 said:
Now I' still waiting, without phone touching. Led is ON (orange colour). Phone is disconected (and me too ). Battery level was 13% before this insydent.
When LED will turn off (I don't know when) I'll reinsert battery and let you know what's up.
I hope, I did't bricked it...
Click to expand...
Click to collapse
Don't worry. I am virtually a 100% sure you have NOT bricked it.
Just don't panic and let the phone switch off first.
BTW, you didn't say if you unlocked your bootloader with HTC Dev site or Revolutionary?
Do you have a Nandroid backup of your previous ROM ?
How new are you to all this (flashing etc)?
Is this the first custom ROM you have flashed on this device?
enigmaamit said:
Don't worry. I am virtually a 100% sure you have NOT bricked it.
Just don't panic and let the phone switch off first.
BTW, you didn't say if you unlocked your bootloader with HTC Dev site or Revolutionary?
Do you have a Nandroid backup of your previous ROM ?
How new are you to all this (flashing etc)?
Is this the first custom ROM you have flashed on this device?
Click to expand...
Click to collapse
My phone was s-off by xtc clip (I did't use revolutionary), boot loader was unlocked on HTC Dev site.
I flashed at first CMW recover, than 4EXT Touch recovery and used it.
I tried a lot of roms, virtuous, endymnion, runny. The best for the beast was CM7.1, nightly. I flashed it month ago and updated succefully. Two days ago I decided to try REAPER. I wiped cache and dalvik's, than flashed reaper v 1.1. Today I updated it to 1.2 version (the same way as always) and I had a problem with dialer, so I wiped everything. Format all ex. sd card was done and I flashed reaper 1.2. I confogured it, just I like (set a new gov reaper, freq 118 (I don't remember) low and 1074 high) and thats it. I tried laucher, sms, phone and thats all.
adix631 said:
My phone was s-off by xtc clip (I did't use revolutionary), boot loader was unlocked on HTC Dev site.
I flashed at first CMW recover, than 4EXT Touch recovery and used it.
I tried a lot of roms, virtuous, endymnion, runny. The best for the beast was CM7.1, nightly. I flashed it month ago and updated succefully. Two days ago I decided to try REAPER. I wiped cache and dalvik's, than flashed reaper v 1.1. Today I updated it to 1.2 version (the same way as always) and I had a problem with dialer, so I wiped everything. Format all ex. sd card was done and I flashed reaper 1.2. I confogured it, just I like (set a new gov reaper, freq 118 (I don't remember) low and 1074 high) and thats it. I tried laucher, sms, phone and thats all.
Click to expand...
Click to collapse
Well in that case, don't worry your phone is safe. Just wait for it to switch off. Then after booting into recovery, just restore the last working ROM backup that you have. Don't flash the Reaper 1.2 that you downloaded till you have confirmed that the md5 checksum matches the one posted by Lowveld.
Hmm. Strange.
Phone turned off - LED was off, so I pulled battery, wait 2-5 minutes (without battery) and tried to turn it on. I saw a black screen. I press vol up/down power buttons, phone vibrated 3 times (quick) and I saw a green LED. I tried turn it on (with vol down button and without it) - nothing. I waited a while then a Led turned off.
I pluged device to the charger - orange led started blinking, so I tried to on phone - nothing. I restarted it (3 buttons) - it vibrated 3 times quickly and the same story from my first post.
Phone is unplugged, orange led is on (not blinking) and no react.
Any ideas??
Can you still boot to recovery?
adix631 said:
Hmm. Strange.
Phone turned off - LED was off, so I pulled battery, wait 2-5 minutes (without battery) and tried to turn it on. I saw a black screen. I press vol up/down power buttons, phone vibrated 3 times (quick) and I saw a green LED. I tried turn it on (with vol down button and without it) - nothing. I waited a while then a Led turned off.
I pluged device to the charger - orange led started blinking, so I tried to on phone - nothing. I restarted it (3 buttons) - it vibrated 3 times quickly and the same story from my first post.
Phone is unplugged, orange led is on (not blinking) and no react.
Any ideas??
Click to expand...
Click to collapse
Well, the blinking signifies inadequate charge for a bootup. Wait till the orange LED stopsa blinking and turns on constantly... then boot into bootloader (Voulme up and Power button - don't let go of the volume button even after releasing the power button) - I don't want you to restart by using three button combo...otherwise you'll be back to the same problem, trying to boot into a broken OS... Just disconnect again and wait for it to switch off.... then reinsert battery, connect to charger, then wait for the LED blinking to stop. Have a little patience! and DON"T RESTART with three button combo. Just boot into bootloader with Voulme up + Power key.
You have to follow these instructions carefully, exactly as i have written. Report back what happens.
enigmaamit said:
Well, the blinking signifies inadequate charge for a bootup. Wait till the orange LED stopsa blinking and turns on constantly... then boot into bootloader (Voulme up and Power button - don't let go of the volume button even after releasing the power button) - I don't want you to restart by using three button combo...otherwise you'll be back to the same problem, trying to boot into a broken OS... Just disconnect again and wait for it to switch off.... then reinsert battery, connect to charger, then wait for the LED blinking to stop. Have a little patience! and DON"T RESTART with three button combo. Just boot into bootloader with Voulme up + Power key.
You have to follow these instructions carefully, exactly as i have written. Report back what happens.
Click to expand...
Click to collapse
I did it exactly like you've written. Waited till phone, switch off, connected it and charged till led stopped blinking, disconnect, and try to boot it into recovery (vol up + power). Phone wibrated 3 times (screen did't react) and the same story. Now waiting for discharging and I'll try again.
Anyway thanks for your help and interest.
What else I can do? If the phone is not responding I can send it to warranty service. Meybe they will honour it... If not...ehss very expensive play.
adix631 said:
I did it exactly like you've written. Waited till phone, switch off, connected it and charged till led stopped blinking, disconnect, and try to boot it into recovery (vol up + power). Phone wibrated 3 times (screen did't react) and the same story. Now waiting for discharging and I'll try again.
Anyway thanks for your help and interest.
What else I can do? If the phone is not responding I can send it to warranty service. Meybe they will honour it... If not...ehss very expensive play.
Click to expand...
Click to collapse
Well, it that's not workin, Wait till the phone switches off again. Then configure adb, make sure it detects your device (use the command: adb devices) and then type the following at the cmd prompt :
adb reboot recovery
This should take you to recovery.
Ok, what can I say? Youe last thread worked!! I restared device, connect to computer - it was found as usb disk. In sdk tool divece was also found, this time as my ds Just restarted a recovery. First I saw an error in 4ext recovery, but it started with orange letters. I wiped all, formated all, recover old system, restart phone. And it works! Now I flshesd last jorgens CM7 and starting to config my phone. But a heart attack was close... Thanks man
adix631 said:
Ok, what can I say? Youe last thread worked!! I restared device, connect to computer - it was found as usb disk. In sdk tool divece was also found, this time as my ds Just restarted a recovery. First I saw an error in 4ext recovery, but it started with orange letters. I wiped all, formated all, recover old system, restart phone. And it works! Now I flshesd last jorgens CM7 and starting to config my phone. But a heart attack was close... Thanks man
Click to expand...
Click to collapse
You're welcome brother! And Congratulations!!
I know what you must have gone through till you reclaimed your phone. I remember the first time i was in a situation like yours... had to figure out this discharge the phone, LED blinking etc... thing on my own..., everyone else said battery pull was my only option. But i sitll didn't do it. I had around 60% battery remaining before this happened, so you can only imagine how many sleepless hours i spent waiting for the damn battery to run dry. http://forum.xda-developers.com/showthread.php?t=1271360
The important thing is to resist the temptation of pulling battery. Everything can be salvaged if you don't do that, but once you fry your eMMC, there is nothing anyone can do without physically repairing the phone.
May I suggest you edit the topic your OP and add the word [SOLVED] to the title. This will ensure anyone in trouble can easily locate this thread out of the cacophony on xda!