here is my problem guys. i was trying to flash my htc touch 2 sprint it with Raphaelhardspl(wrong flashing) and in the process the screen went blank. i was trying to do it one more time and my PC is asking for qualcomm cdmd technologies msn driver, every time i connect the phone to my PC. i have tried it soft reset. and hard reset wont work. any suggestion will be thanks full. thank you. the main problem is that my pc wont recognize ??
WHOEVER solve my problem will pay 50 buck via paypal
The quickest way to brick your phone is to try to flash it with programs meant for other phones, which it appears you have done.( bricked )
Try putting it into bootloader and flashing stock rom , or try mtty.exe, but if your pc won't recognize it and your screen shows no life, it is probably toast. Does it at least have hardspl on it . ?
yes it does have hardspl. there have to be a way that my pc will recognized it. i think.
As denco7 said, have you tried getting into the bootloader mode?
Hold volume down and press the red button with your stylus.
Connect your pro2 to your PC and if it connects the word 'serial' will change into 'USB'.
If it does, your device is not bricked.
I suggest you flash Hard-SPL again, and make sure to follow the instructions exactly! Don't think you can do it just in a minute, just take your time.
Then flash another ROM by using MTTY (see here) and there you'll get some instructions.
Good luck!
it wont go to boot loader mode, when i connect it to the pc it begin to charge and noting happen , then suddenly the light go off and the pc detect a driver is missing quaccom etc. does any one know about that this driver.
I've had that before... that the MSM technology qualcomm **** is asking for a driver.
There's a driver replacement (used before mtty). You can try to install that; altough I don't think it will help.
If you can't get into bootloader your device is (probably) bricked.
What you can also try is getting your battery, sd-card and simcard out of your phone and leave it for an hour. Then put the battery only back, and try to boot.
Does your phone start when you press the start button? So do you feel a vibrate or somethin like that?
no it wont start but maybe by following that MTTY my pc read it, i will try it. . it doesn even bibrate it just that power light show when that phone its charging thats all.
thanks for you comment guys.
That's strange.
There's one last thing you could try: the ultimate hard-reset
Some time ago I bricked my diamond. I tried all available sofkey combinations.
Then, suddenly, my device vibrated like 3 tiimes very loudly.
It didn't still boot nor go into bootloader.
But after about 4 hours it booted!
I only don't know what the combination was... something like VOl UP + VOL DWN + lOCK BUTTON + RESET.
Just try some combinations, maybe it works for you.maybe not, but you could try it.
Related
AFTER UNLOCK NO VOICE OR SPEAKER WORKING I JUST FLASHED WITH
(RUU_Kaiser_HTC_WWE_1.25.405.0_22.39.82.00.b_1.27.04.15_Test) NOW PHONE DOESNT
POWER UP OR BOOT MODE BLANK SCREEN
I TRY TO CONNECT TO THE COMPUTER ASKING DRIVER (DATE INTERFACE)
I NEED YOUR HELP TO GET BACK LIVE
PLEASE
THANKS
How did you unlock it? Did you CID unlock? HardSPL version? Can you get to the bootloader by holding down the camera button and power button and soft reset at the same time?
From the sound of things you loaded a CID locked rom onto your locked phone. This is only a guess though based on the fact that the ROM you loaded included a compatible radio.
Just a tip, next time don't use all caps. It's considered shouting and inappropriate. We understand your urge to get it fixed so we'll help even without the caps
Answering Alibaba0101's questions will help a lot. Also, have you tried taking the battery out and putting it back in?
The phone was on orange.
Step 1: install JumpSPL1.93-KAIS.exe
Step 2: Run KaiserUnlocker.exe (PolarisUnlocker)
Step 3: Flash Hard-SPL (but the screen goes white then i boot the phone manually by pressing camera button) after done.
Step 4: Run unlock Radio (take couple of mint and done and phone reboot)
Step 5: Run Unlocker ( after run unlocker i get 2 option unlock and super cid 000000 and I click checked both option and press okay its take less then 1 mint done.
Step 6: i take it out battery from the phone put different sim card and power on the phone phone was unlocked when I dial help line i didn’t get any sound. No speaker no ear sounds.
then i flashed (RUU_Kaiser_HTC_WWE_1.25.405.0_22.39.82.00.b_1.27. 04.15_Test) and after done flash phone dead screen blank I try to boot the phone by pressing camera button but phone not responding after connect the usb to phone get msg (DATA INTERFACE) driver.
Phone still dead i try to put another battery but still same I did try soft reset hard reset but still dead
Please help
THANKS
lxa786 said:
The phone was on orange.
Step 1: install JumpSPL1.93-KAIS.exe
Step 2: Run KaiserUnlocker.exe (PolarisUnlocker)
Step 3: Flash Hard-SPL (but the screen goes white then i boot the phone manually by pressing camera button) after done.
Step 4: Run unlock Radio (take couple of mint and done and phone reboot)
Step 5: Run Unlocker ( after run unlocker i get 2 option unlock and super cid 000000 and I click checked both option and press okay its take less then 1 mint done.
Step 6: i take it out battery from the phone put different sim card and power on the phone phone was unlocked when I dial help line i didn’t get any sound. No speaker no ear sounds.
then i flashed (RUU_Kaiser_HTC_WWE_1.25.405.0_22.39.82.00.b_1.27. 04.15_Test) and after done flash phone dead screen blank I try to boot the phone by pressing camera button but phone not responding after connect the usb to phone get msg (DATA INTERFACE) driver.
Phone still dead i try to put another battery but still same I did try soft reset hard reset but still dead
Please help
THANKS
Click to expand...
Click to collapse
I don't see the step where you flashed your original radio back after doing the SIM unlock. The radio that you is a special "patched" radio, and the phone will not successfully boot into Windows with it flashed.
Go into the bootloader (hold Camera during power on), and flash a compatible radio. If you haven't flashed a cooked ROM yet, then just hit up the Kaiser Wiki and grab the original ship radio for your phone.
Bootloader is entered by holding the power button and camera button down while soft resetting the phone. (sticking the styles in the hole) Keep holding the 2 buttons down until your in bootloader. Even with the wrong radio the phone should still go into bootloader properly
austinsnyc said:
Bootloader is entered by holding the power button and camera button down while soft resetting the phone. (sticking the styles in the hole) Keep holding the 2 buttons down until your in bootloader. Even with the wrong radio the phone should still go into bootloader properly
Click to expand...
Click to collapse
huh. I don't have to hold down the power button to enter the bootloader. I just hold down the camera button and put the stylus into the reset hole.
Boot Loader
Same here I just hold down camera button and soft reset works every time.
hi I need your more help how can I get phone on boot mode phone dead not responding I tried more then 10 time by pressing camera and power button phone still blank screen.
No display show so how can I flash the phone
Any idea to flash the phone dead mode?
thanks
If you cant get it into boot loader mode, ur gonna have a lot of trouble trying to fix it. Like everyone has said so far... Press and hold both the Power button and Camera button together and then use your stylus to soft reset it.
This has gotten people in the past, so sorry if it sounds dumb.
The Camera button has two settings Full Press and Half Press. Press until it stops then press again. You need to be pushing the Camera Button down all the way to get into Bootloader.
Also I never need to press the power Power Button As well.
I may be wrong but, when the phone is on, you can press the Camera and Soft Reset buttons. When the phone is off, you press the Power, Camera, and Soft Reset buttons to go directly into boot loader.
i tried but screen still blank no light nothing when i put usb into the phone asking driver (data interface)?
Can not go in bootloader help?
Tytn 2 is dead .
Ok last night I try to install the new hyperdragon III BlackStone rom everything is fine untill it finish and it cant load in to window, the computer keep asking me for the data interface and the tilt keep restart and the screen only shows hyperdragen III. I was running hyperdragon III opal (10/11/08) I tried MMTY and reinstall the OE rom but no luck, please help!!
Tytn2 Dead or not??
Tytn 2 is dead if you see data interface driver when put in usb cabel install v3 motorola driver and you will see data qualcomm usb driver i device manager .... this mean that totaly erased memory in tytn2 and its dead,only with jtag can flash again.
Please, tell me how can y do it. I have the same problem....
Step 3: Flash Hard-SPL (but the screen goes white then i boot the phone manually by pressing camera button) after done.
Click to expand...
Click to collapse
I don't see any step about using the white screen fix so I'm guessing you didn't successfully install HardSPL and then after that you tried flashing a ROM whilst being oblivious to the fact that Hard SPL wasn't installed, so you most likely bricked your phone
AllTheWay said:
huh. I don't have to hold down the power button to enter the bootloader. I just hold down the camera button and put the stylus into the reset hole.
Click to expand...
Click to collapse
Dead HTC KAISER
Hello My friends
After along search and Googling on the net without finding any solution. at last I did took a Risk to solve and save my DEAD HTC KAISER . what i did is I ressembled the HTC KAISER , to see if my USB data input was defect, but it was Good, now .......he he.. what i fond avery smal Batterie planted on the motherboard , i took it of the the board , end waited 1 hour . then i place it back , assembeled my HTC KAISER back
Taaaaraaaaa my HTC KAISER Power Led went ON ,,, YES ..Friends . is charging .
after 1/2 hour , I swish the HTC on ,,,, heeeee Is working......flash it with the new ROM wm 6.5 ...really it went Perfect.. end My HTC KAISER... ALIVE AGAIN.
Greatins , and hoppe this will Help you..........Good Luck .
on youtube you can find videos how to dissembele your HATC KAISER.
thanks to XDA-Developers , for this great Forum.
ericc191 said:
If you cant get it into boot loader mode, ur gonna have a lot of trouble trying to fix it. Like everyone has said so far... Press and hold both the Power button and Camera button together and then use your stylus to soft reset it.
Click to expand...
Click to collapse
my kaiser boots up but after the att thing the screen gos black do you know how to fix this
Hi!, how do i reset my phone.... the screen got shorted out, its all black, and i cant input my password to activesync for flashing stock SPL back on. I get error 260 Connection. Also tried hardware hard reset, doesnt seem to work... is there computer software that will let me hard reset from computer? gotta warranty the phone, how do i fix this situation????
Softreset: Stylus in the hole near USB
Hardreset: Vol down + round button in the middle + stylus in the hole near USB
thank you, i tried that, doesnt seem to work
can you reach bootloader mode?
This is the only way I coudl get mine to hard-reset :
Take out the battery....
Put the battery back in....
Press and hold the volume down & center "enter" button
While still pressing those, press and hold the power button for 10 sec...
On my phone, the hard reset confirmation comes up at that point... The other way with usign the soft-reset button did not work for me... I hope this helps
bootloader.... i dont know if i can, the screen is broken, its not lighting up. when i try to hard reset nothing happens, the phone doesnt powercycle.
the method above ( with the power button ) didnt work for me, but thanks
bootloader
i could try going into bootloader by holding power and vol down and button next to usb port. What do I do from there?
i should clarify what I am trying to do. I need to return this phone to warranty dept. They sent me a replacement. So I need to flash my broken phone back to stock Fuze ROM. The screen doesnt work, so i cant see what I'm doing.
When i connect the phone to my pc, i cant active sync because theres a passcode on my phone and screen doesnt work, so i cant input password and establish the connection. Therefore, i cant flash. i get error 260 when trying to flash the ROM (no connection) since its still password locked. So i was trying to hard reset to get rid off password. The vol down, center and pinhole method doesnt work for some reason... i did hit vol up and waited 10 min to be safe, but phone never rebooted as it would have after hard reset. So i figured that didnt work Remember i cant see whats on the screen at all. So what can i do if i'm successful in getting to bootloader screen with vol down, power, pinhole method?...
bmvik said:
i could try going into bootloader by holding power and vol down and button next to usb port. What do I do from there?
i should clarify what I am trying to do. I need to return this phone to warranty dept. They sent me a replacement. So I need to flash my broken phone back to stock Fuze ROM. The screen doesnt work, so i cant see what I'm doing.
When i connect the phone to my pc, i cant active sync because theres a passcode on my phone and screen doesnt work, so i cant input password and establish the connection. Therefore, i cant flash. i get error 260 when trying to flash the ROM (no connection) since its still password locked. So i was trying to hard reset to get rid off password. The vol down, center and pinhole method doesnt work for some reason... i did hit vol up and waited 10 min to be safe, but phone never rebooted as it would have after hard reset. So i figured that didnt work Remember i cant see whats on the screen at all. So what can i do if i'm successful in getting to bootloader screen with vol down, power, pinhole method?...
Click to expand...
Click to collapse
yep try and get it into bootloader, and then connect it to the usb when you think it may be in bootloader..run the RUU and if its in bootloader it should start the RUU like you remember..if its not and you get the error, then its not in bootloader and try it again. id say bootloader is the best bet even over the hard reset. you really should be able to get it in bootloader as long as the actual buttons work on the phone...good luck mate
i have cdma touch pro, and dont know if its different than your fuze , but my boot loader is VOL DOWN + POWER, then SOFT RESET (do them all at the same time, and hold them all for 10 seconds and you should get it)
the-wrangler said:
yep try and get it into bootloader, and then connect it to the usb when you think it may be in bootloader..run the RUU and if its in bootloader it should start the RUU like you remember..if its not and you get the error, then its not in bootloader and try it again. id say bootloader is the best bet even over the hard reset. you really should be able to get it in bootloader as long as the actual buttons work on the phone...good luck mate
i have cdma touch pro, and dont know if its different than your fuze , but my boot loader is VOL DOWN + POWER, then SOFT RESET (do them all at the same time, and hold them all for 10 seconds and you should get it)
Click to expand...
Click to collapse
Thanks a lot! i will try tonight and post the results!
bmvik said:
Thanks a lot! i will try tonight and post the results!
Click to expand...
Click to collapse
yep, try it out and let us know..one of us will have a trick to help you out im sure feel free to pm me for help mate
thanks mate.... looks like vol down key isnt working. omg ... i can get to bootloader in my new fuze, but not old... it just powercycles if i follow the steps
what if I put an nbh on the sd card and powercycle, will it load automatically?
Hello, I am trying to help my friend unbrick his phone.
All I know is that he was trying to use a one click root program and after several reboots the phone would no longer boot. It vibrates three times and flashes an orange light.
If I plug the phone into my computer, clockwork mod recovery with the words "ace hack kit" will show up. I tried wiping data, cachce, etc. and installing Android Revolution HD.
On my computer, if I type "adb devices" then it will show H13142452345 recovery.
If I type adb reboot bootloader the phone will vibrate three times and flash the orange light.
When the phone is plugged into my computer during the blinking orange light, then my computer says "device drivers not found for Qualcomm MSM"
I have also tried booting the phone with the sd card and SIM card removed.
Can anyone help?
Thank you.
**************SOLVED******************
The problem was that my volume buttons were broken. Once I destroyed the ribbon cable connecting the volume buttons to the motherboard, the phone booted up just fine.
azndan2 said:
Hello, I am trying to help my friend unbrick his phone.
All I know is that he was trying to use a one click root program and after several reboots the phone would no longer boot. It vibrates three times and flashes an orange light.
If I plug the phone into my computer, clockwork mod recovery with the words "ace hack kit" will show up. I tried wiping data, cachce, etc. and installing Android Revolution HD.
On my computer, if I type "adb devices" then it will show H13142452345 recovery.
If I type adb reboot bootloader the phone will vibrate three times and flash the orange light.
When the phone is plugged into my computer during the blinking orange light, then my computer says "device drivers not found for Qualcomm MSM"
I have also tried booting the phone with the sd card and SIM card removed.
Can anyone help?
Thank you.
Click to expand...
Click to collapse
First, you shouldn't have used a root program that does not support your device. The only efficient rooting method to the moment is the Hack Kit. Anyway. Try reverting your phone to stock using the hack kit. You shouldn't have wiped data also as you have probably disabled USB debugging. If you can't revert it to stock with the hack kit, then your best choice is to hit the IRC channel and ask for help. The guys there know the business and might be able to help. Hope you.can sort the issue out.
Sent from my Inspire 4G using XDA App
Thanks. I'm not sure what program he was using to try to root the phone, my guess is that he was using the ace hack kit because the recovery on his phone says "ace hack kit" on it. Thanks for the tip on going to the IRC.
You've bricked it, I believe the phone is now in Qualcomm's Diagnostic dload mode.
Confirmed, you're in Qualcomm's Diagnostic mode.
My suggestion is to try and find a PD98IMG file that flashes everything to stock, use a clean FAT32 sd card, put it in the phone, and then try to see if it'll flash it when you press volume-down and power. Apparently that should give you five vibrations, then after 5 minutes, press volume up to let it vibrate once, then spend about another 10 minutes before pressing volume up one more time.
Thanks for the reply Hunter. I've tried a variety of button combinations and methods to try to get it to boot into the five vibration green light mode. Unfortunately, no matter what button combination I press I can only get it into 3 vibration orange light mode.
Did you attempt the Hack kit ?
Help please
Im in a dire situation, what do I do. Could some one give me a step by step explanation??
Thank you that would be a big help
it vibrated 5 times and i have a green light, for a while the battery charging thing came up, what do I do??????
I can not help you now, but as a last resort could find a technician and ask for "medusa box"(search in crome explorer). I have this device and I'm back to life a dozen android devices completely bricked, and the htc inspire 4g is fully supported by medusa box, luck
Hello to everyone. I beg your help, please. I bought this amazing second hand tablet last friday. At the first attemp, and because I didn't want to read all the threads, I bricked the tablet. Yes, stupid thought, I know.
Because I wasn't happy with the result, I wiped all and delete bootloader, system, data... Everything. I know something with Microsoft issues and brave me (and silly) I thought It was similar, that I could start from outside of the tablet even if it was blank.
Anyway, the facts are:
The tablet is allways on, in APX mode. When I press down the power boton, it reboot. I know because when it's conected to my laptop, I can see the USB interface conected and the APX mode on it.
The screen is allways in black. ALLWAYS. No matter if I try to start in recovery in bootloader or any other way to start the system. Black, nice black.
Of course, no result in Power + Vol up, Power + Vol -, pressing power during 3 hours and 23 minutes... (I'm joking), but for long.
The only signal by which I know that it's not dead at all its when I conect the charger. I can see the small orange light in the power buton saying: "I'm alive"
Ok, I don't know what to do. I've read during the weekend as much as I could, tried evrything and nothing fixed. If it helps, before playing to be God, I had Android 4.0.1, I unlocked the bootloader with the apk, I installed the TWRP recovery and everything were right until I wanted to update the rom. Some mystakes that I don't remember and this is what I can tell you. Any holy soul which can help me, please? If not, can anyone help me? Thank you and I'll be looking forward your help.
evoin said:
Hello to everyone. I beg your help, please. I bought this amazing second hand tablet last friday. At the first attemp, and because I didn't want to read all the threads, I bricked the tablet. Yes, stupid thought, I know.
Because I wasn't happy with the result, I wiped all and delete bootloader, system, data... Everything. I know something with Microsoft issues and brave me (and silly) I thought It was similar, that I could start from outside of the tablet even if it was blank.
Anyway, the facts are:
The tablet is allways on, in APX mode. When I press down the power boton, it reboot. I know because when it's conected to my laptop, I can see the USB interface conected and the APX mode on it.
The screen is allways in black. ALLWAYS. No matter if I try to start in recovery in bootloader or any other way to start the system. Black, nice black.
Of course, no result in Power + Vol up, Power + Vol -, pressing power during 3 hours and 23 minutes... (I'm joking), but for long.
The only signal by which I know that it's not dead at all its when I conect the charger. I can see the small orange light in the power buton saying: "I'm alive"
Ok, I don't know what to do. I've read during the weekend as much as I could, tried evrything and nothing fixed. If it helps, before playing to be God, I had Android 4.0.1, I unlocked the bootloader with the apk, I installed the TWRP recovery and everything were right until I wanted to update the rom. Some mystakes that I don't remember and this is what I can tell you. Any holy soul which can help me, please? If not, can anyone help me? Thank you and I'll be looking forward your help.
Click to expand...
Click to collapse
Are you able to access fastboot? If so, flash the STOCK ASUS 4.0.1 Rom again. The mistake I think you made was flashing a ROM not compatible with the bootloader you have. You first have to update the bootloader to 4.1.1 or 4.2.1 to flash any of the current ROMS.
No fastboot, no bootloader update.
cmendonc2 said:
Are you able to access fastboot? If so, flash the STOCK ASUS 4.0.1 Rom again. The mistake I think you made was flashing a ROM not compatible with the bootloader you have. You first have to update the bootloader to 4.1.1 or 4.2.1 to flash any of the current ROMS.
Click to expand...
Click to collapse
Thanks for the reply:
I can't access fastboot. The tablet does nothing, just allways on in APX, so I can't update the bootloader. Neither I can't switch it off. I've read smething about run out the battery and start a process with ODIN?
I haven't tried it before, but maybe there's a way to create a bootable SD that will automatically install one of the stock ROMs so you can start over again?
If you can't get to the bootloader/fastboot/recovery and only have APX and no back upped NVFlash files then I think you are bricked unfortunately
hi is there any solution to solve this problem, or tablet dead
I'm in the same situation! :crying:
no solution???
Same story
Same here -- black screen, PC recognizes it as an APX device, but neither fastboot nor adb seem to work.
I didn't even try to mod mine. I was just using it normally, and it crashed, and now all it does is give me a black screen. When I poke the reset button, my PC notices the device disconnection and then a minute later it re-connects, but still nothing.
Holding down volume up/down during reset does nothing. Holding down power, with or without volume buttons, for an extended period does nothing.
This looks to be like an epidemic problem for these devices. Has nobody gotten a handle on it yet?
pty
I am also in your situation.
I have a tablet with Tegra xperia 3, black screen! APX mode only!
Does not read any adb and fastboot driver!!
There are new?
Hi everyone,
for me now the same situation. Only APX aviable. no fastboot ect...
pls help me solve this issue.
Thanks a lot.
Turn on in APX-Mode. You won't see anything on the screen, the display does not turn on.
If you connect the USB cable to a Windows PC, Windows will recognize it as an APX device.
On this mode you may use nvflash tool http://forum.xda-developers.com/showthread.php?t=1969797.
If nothing works, you should exchange the Mainboard!
Good Morning,
yesterday when i flashed a rom, something goes wrong.
My opo don't go in boot animation and work only the recovery and fastboot.
I don't know why but afther another reboot the phone is dead, i think that is a normal hard brick so i try to restore with the tool "msm8974 download tool" but it don't work, when i start the restore come out a red word.
I never seen a hard brick like this, the phone is 100% dead , when i press the power button don't vibrates and nothing come out, diplay is black.
What can i do to restore my opo? :crying:
Try Wiping everything from TWRP and try a different ROM.
Another thing to try is connecting ADB to get the logcat.
Can you give more details on what you've tried so far?
Additionally, I remember reading that the OPO can stop booting correctly when the battery starts failing.
umer936 said:
Try Wiping everything from TWRP and try a different ROM.
Another thing to try is connecting ADB to get the logcat.
Can you give more details on what you've tried so far?
Additionally, I remember reading that the OPO can stop booting correctly when the battery starts failing.
Click to expand...
Click to collapse
Now the phone is dead, if I press the power button nothing come out (no vibration, no screen) the phone look like without battery! (But it is over 50%)
I followed the tutorial to restore HARD BRICK with the tool but it don't success!
ghibli2 said:
Now the phone is dead, if I press the power button nothing come out (no vibration, no screen) the phone look like without battery! (But it is over 50%)
I followed the tutorial to restore HARD BRICK with the tool but it don't success!
Click to expand...
Click to collapse
Me to.. this morning my phone dead.. i dont know what can i do again..
Trying pressing all combination button not showing anything even in pc device manager usb not recognize or qhsusb_bulk not appear
Anyone can help me please.. @netbuzz
I have bricked this phone in and out, believe me lol all you gotta do is open the phone, unscrew all (TOP HALF) screws and UN plugg battery......wait about 30 sec RE plugg/connect battery and re run the unbricking tool