Database Info

Htc Kaiser Dead After Flash Finshed

AFTER UNLOCK NO VOICE OR SPEAKER WORKING I JUST FLASHED WITH
(RUU_Kaiser_HTC_WWE_1.25.405.0_22.39.82.00.b_1.27.04.15_Test) NOW PHONE DOESNT
POWER UP OR BOOT MODE BLANK SCREEN
I TRY TO CONNECT TO THE COMPUTER ASKING DRIVER (DATE INTERFACE)
I NEED YOUR HELP TO GET BACK LIVE
PLEASE
THANKS

How did you unlock it? Did you CID unlock? HardSPL version? Can you get to the bootloader by holding down the camera button and power button and soft reset at the same time?
From the sound of things you loaded a CID locked rom onto your locked phone. This is only a guess though based on the fact that the ROM you loaded included a compatible radio.

Just a tip, next time don't use all caps. It's considered shouting and inappropriate. We understand your urge to get it fixed so we'll help even without the caps
Answering Alibaba0101's questions will help a lot. Also, have you tried taking the battery out and putting it back in?

The phone was on orange.
Step 1: install JumpSPL1.93-KAIS.exe
Step 2: Run KaiserUnlocker.exe (PolarisUnlocker)
Step 3: Flash Hard-SPL (but the screen goes white then i boot the phone manually by pressing camera button) after done.
Step 4: Run unlock Radio (take couple of mint and done and phone reboot)
Step 5: Run Unlocker ( after run unlocker i get 2 option unlock and super cid 000000 and I click checked both option and press okay its take less then 1 mint done.
Step 6: i take it out battery from the phone put different sim card and power on the phone phone was unlocked when I dial help line i didn’t get any sound. No speaker no ear sounds.
then i flashed (RUU_Kaiser_HTC_WWE_1.25.405.0_22.39.82.00.b_1.27. 04.15_Test) and after done flash phone dead screen blank I try to boot the phone by pressing camera button but phone not responding after connect the usb to phone get msg (DATA INTERFACE) driver.
Phone still dead i try to put another battery but still same I did try soft reset hard reset but still dead
Please help
THANKS

lxa786 said:
The phone was on orange.
Step 1: install JumpSPL1.93-KAIS.exe
Step 2: Run KaiserUnlocker.exe (PolarisUnlocker)
Step 3: Flash Hard-SPL (but the screen goes white then i boot the phone manually by pressing camera button) after done.
Step 4: Run unlock Radio (take couple of mint and done and phone reboot)
Step 5: Run Unlocker ( after run unlocker i get 2 option unlock and super cid 000000 and I click checked both option and press okay its take less then 1 mint done.
Step 6: i take it out battery from the phone put different sim card and power on the phone phone was unlocked when I dial help line i didn’t get any sound. No speaker no ear sounds.
then i flashed (RUU_Kaiser_HTC_WWE_1.25.405.0_22.39.82.00.b_1.27. 04.15_Test) and after done flash phone dead screen blank I try to boot the phone by pressing camera button but phone not responding after connect the usb to phone get msg (DATA INTERFACE) driver.
Phone still dead i try to put another battery but still same I did try soft reset hard reset but still dead
Please help
THANKS
Click to expand...
Click to collapse
I don't see the step where you flashed your original radio back after doing the SIM unlock. The radio that you is a special "patched" radio, and the phone will not successfully boot into Windows with it flashed.
Go into the bootloader (hold Camera during power on), and flash a compatible radio. If you haven't flashed a cooked ROM yet, then just hit up the Kaiser Wiki and grab the original ship radio for your phone.

Bootloader is entered by holding the power button and camera button down while soft resetting the phone. (sticking the styles in the hole) Keep holding the 2 buttons down until your in bootloader. Even with the wrong radio the phone should still go into bootloader properly

austinsnyc said:
Bootloader is entered by holding the power button and camera button down while soft resetting the phone. (sticking the styles in the hole) Keep holding the 2 buttons down until your in bootloader. Even with the wrong radio the phone should still go into bootloader properly
Click to expand...
Click to collapse
huh. I don't have to hold down the power button to enter the bootloader. I just hold down the camera button and put the stylus into the reset hole.

Boot Loader
Same here I just hold down camera button and soft reset works every time.

hi I need your more help how can I get phone on boot mode phone dead not responding I tried more then 10 time by pressing camera and power button phone still blank screen.
No display show so how can I flash the phone
Any idea to flash the phone dead mode?
thanks

If you cant get it into boot loader mode, ur gonna have a lot of trouble trying to fix it. Like everyone has said so far... Press and hold both the Power button and Camera button together and then use your stylus to soft reset it.

This has gotten people in the past, so sorry if it sounds dumb.
The Camera button has two settings Full Press and Half Press. Press until it stops then press again. You need to be pushing the Camera Button down all the way to get into Bootloader.
Also I never need to press the power Power Button As well.

I may be wrong but, when the phone is on, you can press the Camera and Soft Reset buttons. When the phone is off, you press the Power, Camera, and Soft Reset buttons to go directly into boot loader.

i tried but screen still blank no light nothing when i put usb into the phone asking driver (data interface)?

Can not go in bootloader help?
Tytn 2 is dead .

Ok last night I try to install the new hyperdragon III BlackStone rom everything is fine untill it finish and it cant load in to window, the computer keep asking me for the data interface and the tilt keep restart and the screen only shows hyperdragen III. I was running hyperdragon III opal (10/11/08) I tried MMTY and reinstall the OE rom but no luck, please help!!

Tytn2 Dead or not??
Tytn 2 is dead if you see data interface driver when put in usb cabel install v3 motorola driver and you will see data qualcomm usb driver i device manager .... this mean that totaly erased memory in tytn2 and its dead,only with jtag can flash again.

Please, tell me how can y do it. I have the same problem....

Step 3: Flash Hard-SPL (but the screen goes white then i boot the phone manually by pressing camera button) after done.
Click to expand...
Click to collapse
I don't see any step about using the white screen fix so I'm guessing you didn't successfully install HardSPL and then after that you tried flashing a ROM whilst being oblivious to the fact that Hard SPL wasn't installed, so you most likely bricked your phone

AllTheWay said:
huh. I don't have to hold down the power button to enter the bootloader. I just hold down the camera button and put the stylus into the reset hole.
Click to expand...
Click to collapse
Dead HTC KAISER
Hello My friends
After along search and Googling on the net without finding any solution. at last I did took a Risk to solve and save my DEAD HTC KAISER . what i did is I ressembled the HTC KAISER , to see if my USB data input was defect, but it was Good, now .......he he.. what i fond avery smal Batterie planted on the motherboard , i took it of the the board , end waited 1 hour . then i place it back , assembeled my HTC KAISER back
Taaaaraaaaa my HTC KAISER Power Led went ON ,,, YES ..Friends . is charging .
after 1/2 hour , I swish the HTC on ,,,, heeeee Is working......flash it with the new ROM wm 6.5 ...really it went Perfect.. end My HTC KAISER... ALIVE AGAIN.
Greatins , and hoppe this will Help you..........Good Luck .
on youtube you can find videos how to dissembele your HATC KAISER.
thanks to XDA-Developers , for this great Forum.

ericc191 said:
If you cant get it into boot loader mode, ur gonna have a lot of trouble trying to fix it. Like everyone has said so far... Press and hold both the Power button and Camera button together and then use your stylus to soft reset it.
Click to expand...
Click to collapse
my kaiser boots up but after the att thing the screen gos black do you know how to fix this

htc touch pro 2 blank screeN

here is my problem guys. i was trying to flash my htc touch 2 sprint it with Raphaelhardspl(wrong flashing) and in the process the screen went blank. i was trying to do it one more time and my PC is asking for qualcomm cdmd technologies msn driver, every time i connect the phone to my PC. i have tried it soft reset. and hard reset wont work. any suggestion will be thanks full. thank you. the main problem is that my pc wont recognize ??
WHOEVER solve my problem will pay 50 buck via paypal

The quickest way to brick your phone is to try to flash it with programs meant for other phones, which it appears you have done.( bricked )
Try putting it into bootloader and flashing stock rom , or try mtty.exe, but if your pc won't recognize it and your screen shows no life, it is probably toast. Does it at least have hardspl on it . ?

yes it does have hardspl. there have to be a way that my pc will recognized it. i think.

As denco7 said, have you tried getting into the bootloader mode?
Hold volume down and press the red button with your stylus.
Connect your pro2 to your PC and if it connects the word 'serial' will change into 'USB'.
If it does, your device is not bricked.
I suggest you flash Hard-SPL again, and make sure to follow the instructions exactly! Don't think you can do it just in a minute, just take your time.
Then flash another ROM by using MTTY (see here) and there you'll get some instructions.
Good luck!

it wont go to boot loader mode, when i connect it to the pc it begin to charge and noting happen , then suddenly the light go off and the pc detect a driver is missing quaccom etc. does any one know about that this driver.

I've had that before... that the MSM technology qualcomm **** is asking for a driver.
There's a driver replacement (used before mtty). You can try to install that; altough I don't think it will help.
If you can't get into bootloader your device is (probably) bricked.
What you can also try is getting your battery, sd-card and simcard out of your phone and leave it for an hour. Then put the battery only back, and try to boot.
Does your phone start when you press the start button? So do you feel a vibrate or somethin like that?

no it wont start but maybe by following that MTTY my pc read it, i will try it. . it doesn even bibrate it just that power light show when that phone its charging thats all.
thanks for you comment guys.

That's strange.
There's one last thing you could try: the ultimate hard-reset
Some time ago I bricked my diamond. I tried all available sofkey combinations.
Then, suddenly, my device vibrated like 3 tiimes very loudly.
It didn't still boot nor go into bootloader.
But after about 4 hours it booted!
I only don't know what the combination was... something like VOl UP + VOL DWN + lOCK BUTTON + RESET.
Just try some combinations, maybe it works for you.maybe not, but you could try it.

HTC Touch Pro T7272 Stuck at Startup

Hello, well, after several searching ended up here... my first post (like all of us when in trouble)
When trying to enter the tri-color screen, we pressed several times power+volume down and reset button but the phone never gets there, no matter what you do and now it is stuck at the "boot" screen that says: "Touch pro" in white letters and in the right down corner, with red letters says:
R 1.02.25.19
G 52.33.25.17W
D 1.94.00.00
Now, what to do here? it doesn´t boot, no hard reset, no nothing, if i press the reset button re-powers and gets there again... help..!!!
Thanks.
Sergio.

squiros1976 said:
Hello, well, after several searching ended up here... my first post (like all of us when in trouble)
When trying to enter the tri-color screen, we pressed several times power+volume down and reset button but the phone never gets there, no matter what you do and now it is stuck at the "boot" screen that says: "Touch pro" in white letters and in the right down corner, with red letters says:
R 1.02.25.19
G 52.33.25.17W
D 1.94.00.00
Now, what to do here? it doesn´t boot, no hard reset, no nothing, if i press the reset button re-powers and gets there again... help..!!!
Thanks.
Sergio.
Click to expand...
Click to collapse
Do entering bootloader : http://wiki.xda-developers.com/index.php?pagename=Raphael_For_Beginners#bootloader (With the device turned off, press and hold the VOLUME DOWN and POWER buttons, then press the RESET button with the stylus)
Then flash new ROM, i hope it's helping

Already tried that...
erwinpiero said:
Do entering bootloader :
(With the device turned off, press and hold the VOLUME DOWN and POWER buttons, then press the RESET button with the stylus)
Then flash new ROM, i hope it's helping
Click to expand...
Click to collapse
That´s exactly why i ended with the phone stuck at the first time... i recently got this phone and i wanted to see the bootloader version and stuff to do a firmware update but now it´s just there all the time. Not even being recognized by the pc.
Thanks.

Had You try flash via SD Card?

erwinpiero said:
Had You try flash via SD Card?
Click to expand...
Click to collapse
Well, no, i don´t have an sd card available now... one thing i forgot to say is the phone, after it is on that screen, never turns off again unless you remove the battery... and yes, i have left it on for a day, same thing...
What is the procedure to do the sd card flash thing? it that needs to get to the tree-color screen forget it... that´s exactly what the phone doesn´t do...
Thanks.
Sergio.

Hello Sir, to flash using SD card, you can read it here http://forum.xda-developers.com/showthread.php?t=448008 see number 5.

HTC Fuze
I had the same problem. None of the hard resets worked on my phone. The screen would be stuck on my lock screen and unresponsive. It would not shut off unless the battery was taken out.
Now it's working fine, all I had to do was press the reset button and enter in the code a1b2c3.
Hope this helps.

nessab04 said:
I had the same problem. None of the hard resets worked on my phone. The screen would be stuck on my lock screen and unresponsive. It would not shut off unless the battery was taken out.
Now it's working fine, all I had to do was press the reset button and enter in the code a1b2c3.
Hope this helps.
Click to expand...
Click to collapse
Hi,
Interesting... i´m not the only one with that problem then.... code doesn´t do anything... still same screen....

...no bootloader...
erwinpiero said:
Hello Sir, to flash using SD card, you can read it here --- see number 5.
Click to expand...
Click to collapse
Hello,
Ok, well, the main problem here is that i can´t get into bootloader... the phone is stuck at the fist "Touch pro" screen and nothing else happens...

Anyone with a clue on this? is this phone bricked then...

you sure youre puttin it into bootloader correctly? these things are pretty hard to brick, and can be put through hell and back and still be able to put into bootloader. make sure the hold VOLUME DOWN + POWER, and at the same time RESET WITH THE STYLUS IN THE BOTTOM...youll want to HOLD ALL THREE untill you see the tri colour bootloader screen. keep trying mate, it should go

Finally got bootloader...
the-wrangler said:
you sure youre puttin it into bootloader correctly? these things are pretty hard to brick, and can be put through hell and back and still be able to put into bootloader. make sure the hold VOLUME DOWN + POWER, and at the same time RESET WITH THE STYLUS IN THE BOTTOM...youll want to HOLD ALL THREE untill you see the tri colour bootloader screen. keep trying mate, it should go
Click to expand...
Click to collapse
Finally, after several tries it got into bootloader... now the thing doesn't end here because for some reason when i try to upload the Raphael Hard_SPL the phone goes ok to 0% and in about a minute a communication error appears and that's it...
We are moving forward... at least.

Bootloader Info.
Tried to flash via microSD but the phone says not allow..i guess that's because the hard SPL is not installed and it has the stock... here's what the bootloader shows, i'm not being able to install olinex hardSPL...
RAPH100
SPL-1.94.0000
MicroP-Raph (LED) v13
MicroP-Raph (KEY) v5
PSOC-Raph STAGE_CVT v0x36
PCBID 0x80
RID 0x0
ideas?

...no way to flash it back....
so... i guess there´s no way to get this back into business... when trying to flash always reports communication error at 0%...

You HAVE to flash hard spl off of a pc-it won't work flashing off an sd card (ever, no matter what you try), and I've heard you can run into problems (brick-type ones) trying to flash it off an sd card. It requires a special ruu to run. This is why it's packaged with the ruu, and you're told to only use that ruu for flashing hard spl.
I'm not sure why you're pressing power when trying to go into bootloader. All you need to do is press and -get this- HOLD DOWN volume down and then soft reset with your stylus. You can even press and hold volume down and do a software soft reset. I've used voice command to activate a soft reset shortcut in my start menu, and having vol down pressed sends you right into bootloader. Release volume down only when the tricolor screen appears. You don't need to hold down the reset button with the stylus. Just tap it and you're done.

Farmer Ted said:
You HAVE to flash hard spl off of a pc-it won't work flashing off an sd card (ever, no matter what you try), and I've heard you can run into problems (brick-type ones) trying to flash it off an sd card. It requires a special ruu to run. This is why it's packaged with the ruu, and you're told to only use that ruu for flashing hard spl.
I'm not sure why you're pressing power when trying to go into bootloader. All you need to do is press and -get this- HOLD DOWN volume down and then soft reset with your stylus. You can even press and hold volume down and do a software soft reset. I've used voice command to activate a soft reset shortcut in my start menu, and having vol down pressed sends you right into bootloader. Release volume down only when the tricolor screen appears. You don't need to hold down the reset button with the stylus. Just tap it and you're done.
Click to expand...
Click to collapse
ya i just noticed the RAPH100 in his info he posted and the t7272 in the header..mines a RAPH800 and bootloader HAS to have vol + power..anyway, i remember having an issue with something similar with my old vogue..have you tried flashing the shipped stock rom back on? if not, try flashing the stock back on it and if it goes, then try the unlock afterwards. dont fret bud, someone here will get you sorted out
here, i found this as im not well versed in raph100s. its a chart with raph100 roms. im sure some must be shipped stock roms and may be worth a try. sorry i couldnt help more, like i said hopefully someone who knows your device better may be able to help
http://wiki.xda-developers.com/index.php?pagename=HTC_Raphael_WM6.1_ROMs

How about flashing official ROM via microSD card?

patrick_spd4u said:
How about flashing official ROM via microSD card?
Click to expand...
Click to collapse
Download the official rom, right click on the exe and extract it somewhere, you'll get several files, rename RUU_signed.nbh to raphimg.nbh, move it to the root of your sd card and you should be able to install it. It should contain splash screen, radio and os.

No way to flash HardSPL...
Hello, thank you for your help! in fact the volume down+reset works perfect to get into bootloader but every time i try to flash hardSPL or stock rom via USB it says "communication error" and the phone displays a 0% bar...
Windows7 is detecting it as HTC USB Sync.
Thanks..
Farmer Ted said:
You HAVE to flash hard spl off of a pc-it won't work flashing off an sd card (ever, no matter what you try), and I've heard you can run into problems (brick-type ones) trying to flash it off an sd card. It requires a special ruu to run. This is why it's packaged with the ruu, and you're told to only use that ruu for flashing hard spl.
I'm not sure why you're pressing power when trying to go into bootloader. All you need to do is press and -get this- HOLD DOWN volume down and then soft reset with your stylus. You can even press and hold volume down and do a software soft reset. I've used voice command to activate a soft reset shortcut in my start menu, and having vol down pressed sends you right into bootloader. Release volume down only when the tricolor screen appears. You don't need to hold down the reset button with the stylus. Just tap it and you're done.
Click to expand...
Click to collapse

...will try it again...
Hi
In fact the most close to the rom i had on that cell is ruu_signed_1.90.401.1_wwe, downloaded it and will try it again later using sdcard... one thing i wonder is the SPL version which is 1.94.00.00 on my phone.
Sergio.
freakzone said:
Download the official rom, right click on the exe and extract it somewhere, you'll get several files, rename RUU_signed.nbh to raphimg.nbh, move it to the root of your sd card and you should be able to install it. It should contain splash screen, radio and os.
Click to expand...
Click to collapse

HD2 died after Manilla mod

Hi all,
after installing volDeus BG tweakv 0.5 my phone died. i can't restart it and i can't perform a hard reset. i also tried the red reset button from the back - nothing. it's not even charging. i tried a different battery but didn't solve the problem. any help would be appreciated. i don't want to send it back for repair.

It happened to me after manilla, i made this factory reset and after that the phone worked fine.
Performing a factory reset using phone buttons
If you cannot turn on your phone or access the phone settings, you can still perform a factory reset by using buttons on the phone.
With your phone powered off, press and hold the VOLUME UP and VOLUME DOWN buttons.
While holding the volume buttons, press the END/POWER button briefly and then release it.
When you see a warning message on screen, release the VOLUME UP and VOLUME DOWN buttons.
Press the VOLUME UP button to perform the reset, or press any other button to cancel the reset.

thanks for reply. like i said, i can't perform a hard reset because the phone is not responding. when i press the volume up, down and power button nothing happens. i don't know what to do.

Ahhhhhh.. me 2
My hd was dead during flashing and still not working but a good thing......
I bought a new HD2.
But if some one have an idea plz let me know.
Thanks in advance

l3onard said:
thanks for reply. like i said, i can't perform a hard reset because the phone is not responding. when i press the volume up, down and power button nothing happens. i don't know what to do.
Click to expand...
Click to collapse
If you're unable to perform a hard reset with the hard keys as explained above, you don't have any other choice but to send it in for repair as far as I know...sorry.

I'd suggest first taking out the battery for a couple of hours and then try again.

de Wolfe said:
I'd suggest first taking out the battery for a couple of hours and then try again.
Click to expand...
Click to collapse
i'll try this. thanks.

de Wolfe said:
I'd suggest first taking out the battery for a couple of hours and then try again.
Click to expand...
Click to collapse
l3onard said:
i'll try this. thanks.
Click to expand...
Click to collapse
Also try this;
1. Remove the battery
2. Plug the USB cable to your computer and to your HD2
3. Push and hold volume down/up
4. Insert the battery
Normally the HD2 would start when doing this.

wardh said:
Also try this;
1. Remove the battery
2. Plug the USB cable to your computer and to your HD2
3. Push and hold volume down/up
4. Insert the battery
Normally the HD2 would start when doing this.
Click to expand...
Click to collapse
thanks but it's not working. maybe because i deactivated charging when connected to PC.

with the combination volume -, reset and power i managed to enter the bootloader. anybody help me to go on pls?

l3onard said:
with the combination volume -, reset and power i managed to enter the bootloader. anybody help me to go on pls?
Click to expand...
Click to collapse
1. L3nny, for future reference, Co0kie's Home Tab v1.8.5 already has the voldeus skinning function built-in, so there's no more need for it in the future... but since you've got it now... calm down and bear with me here...
2. Voldeus' skinning does not mess with your rom image at all, and any changes can be reversed with a HardReset (i've been there and done that). A HardReset does take 3 hands and a few tries to get it for the first time. The red button on the back is only a SoftReset, same as taking the battery out, so that's not gonna work. And since you've just seen the bootloader now, your previous HardReset attempt probably didn't have the correct buttons combination, so it never worked. Try again using this combo from TBoy2000's HowTo thread: remember it's pressing volumeUP AND Down together AND Power button. you need three thumbs
tboy2000 said:
1. With the device turned off, press and hold the VOLUME UP and VOLUME DOWN buttons, then briefly press the POWER button.
2. Continue pressing the VOLUME UP and VOLUME DOWN buttons until you see this message on the screen:
"This operation will delete all your personal data, and reset all settings to the manufacturer default settings. Press VolUp to restore manufacturer defaults, or press other keys to cancel."
3. Release the VOLUME UP and VOLUME DOWN buttons.
4. Press the VOLUME UP button to perform the hard reset, or press any other button to cancel the reset.
Click to expand...
Click to collapse
good luck

atlaswing said:
1. L3nny, for future reference, Co0kie's Home Tab v1.8.5 already has the voldeus skinning function built-in, so there's no more need for it in the future... but since you've got it now... calm down and bear with me here...
2. Voldeus' skinning does not mess with your rom image at all, and any changes can be reversed with a HardReset (i've been there and done that). A HardReset does take 3 hands and a few tries to get it for the first time. The red button on the back is only a SoftReset, same as taking the battery out, so that's not gonna work. And since you've just seen the bootloader now, your previous HardReset attempt probably didn't have the correct buttons combination, so it never worked. Try again using this combo from TBoy2000's HowTo thread: remember it's pressing volumeUP AND Down together AND Power button. you need three thumbs
good luck
Click to expand...
Click to collapse
hard reset is not working. i don't think i do it wrong, because it's not the first time i try this.
i copied shell32.exe and aygshell.dll from voldeus' post an dput it on my sd card. i chose some settings, chose the wallpaper and soft reset. but the phone froze at start-up. i put out the battery and from that moment, i couldn't do anything.
if i can enter the bootloader does it mean i can install HSPL and maybe a stock or custom ROM? but if something goes wrong i loose my warranty!
please help me guys, i'm lost.

1) Maby your battery charge is too low ( maby, your usb port is broken and charging is not ON)
Try to connect your HD2 to charge
Its will be better if you will go to service centre.
sorry for my bad English

l3onard said:
hard reset is not working. i don't think i do it wrong, because it's not the first time i try this.
i copied shell32.exe and aygshell.dll from voldeus' post an dput it on my sd card. i chose some settings, chose the wallpaper and soft reset. but the phone froze at start-up. i put out the battery and from that moment, i couldn't do anything.
if i can enter the bootloader does it mean i can install HSPL and maybe a stock or custom ROM? but if something goes wrong i loose my warranty!
please help me guys, i'm lost.
Click to expand...
Click to collapse
Is your machine tied to a certain provider? If it is send it back and get a new one.You obviously have a faulty machine.Easy way to bootloader,
Hold volume down.
Take off back.
Press red button.
Bootloader appears flash radio or ROM

i tried with another battery and nothing changed. so i solved this problem already.
yes, it's an orange phone. what would be better: trying to flash a new ROM (if something go wrong i loose the warranty) or send it back for repair?

l3onard said:
i tried with another battery and nothing changed. so i solved this problem already.
yes, it's an orange phone. what would be better: trying to flash a new ROM (if something go wrong i loose the warranty) or send it back for repair?
Click to expand...
Click to collapse
New phone definitely.

l3onard said:
i tried with another battery and nothing changed. so i solved this problem already.
yes, it's an orange phone. what would be better: trying to flash a new ROM (if something go wrong i loose the warranty) or send it back for repair?
Click to expand...
Click to collapse
I dont know but i think that: to flash a new ROM you must enter in bootloader.
It is better to change a device for the new
Its a critical problem. This problem can appear again even if you repair your phone.
If you have official guarantee - you must change your device ( go to your service centre )

DUDE!~!!!!~! You're already in bootloader, just flash your original orange STOCK ROM already and be done with this!!! ALSO, you MUST take out your SD card, since that maybe the problem to begin with (having your core system files at the root of your SD is not a smart idea). If that DOESN'T work, then send the damn thing back to Orange for an exchange! Your choices are really simple, why are you wasting everone's time with this!
Good luck

i just wanted your opinion about my problem beeing a beginner in WM phones. i think always is better to ask a second opinion, especially when you are a newbie. if i wasted someones time i'm sorry.
anyway, thanks for the answers. i'll send it back to orange.

I wouldn't send the phone to repair.
1. enter bootloader-mode
2. mtty task29 search forum
3. enter bootloader again
4. flash orange original rom
5. after flashing perform a hard reset

[HELP] Cannot enter bootloader!!

Hello
I had HTC Diamond before and now i bought HTC Touch Pro.
It has original O2 rom and I am trying to flash a new one. But I cannot enter bootloader. I did Hard-SPL but since i cannot enter bootloader I cannot check if it was succesful or not. I tried all the button combinations (like vol down + enter + reset etc...) but it was unsuccesfull. And i even tried to copy EnterBootloader.exe to the phone and run it. But the screen just goes black and thats all. And when I was trying to do HARD-SPL the screen also went only black. I never seen the three color screen. Please help me!
Thanks

Moved as not ROM Development.

Well, you're probably doing it wrong. Hold volume down, then soft reset. Keep holding vol down until the tricolor screen appears. Don't hold the reset button down; just push it and release it.

Im doing it right. Im sure

so u re trying to flash via card or not, if you're trying to flash via PC dont forget to connect with active sync before, if you are trying to connect with SD card dont forget to do a clean format of it before

I remembered that I actually had the issue once (no idea why, it only happened on one rom about a year ago). Try doing a hard reset, then go into bootloader (instead of pushing vol up and re-booting). If that doesn't work, then start the boot process, and when it hits the alignment screen, try to go into bootloader.