Database Info

[GUIDE - YMMV] Connect to 4G sooner & stay on longer

Swap a couple words, and that title could be a Viagra commercial
Anyways, looking at the changes we made to reconnect to 4G faster, these values should make us connect sooner, and drop the connection later. Should be good for fringe areas. I'll describe every change and explain what they do, so bear with me:
NOTE: All these changes will be made in the EPST menu. To get there, dial ##DATA# and choose edit mode. You'll have to enter your MSL. Then choose WiMax in the menu. Don't change anything except what I tell you, because you'll eff something up most likely. If this doesn't work for you, I've also mentioned the defaults so you can go back.
WiMAX_Entry_RX(RSSI)(dBm) - Default is -89. This is the minimum signal it has to be picking up to connect. I'm not sure what the best value here is, but the lower the number, the quicker the connect, since it will connect to a weaker signal. You'll have to experiment some with this, I recommend trying about -95 to -100 first. If it's unstable, raise the value closer to -89.
WiMAX_Entry_CINR(dB) - Default is 4. This is the Carrier to Interface Noise Ratio. The higher it is, the clearer the connection has to be to connect. Change it to 3. You may be able to push it all the way down to 2, but that is probably pushing it. EDIT: Sorry, didn't realize you couldn't set this without it being 4 or higher. You can still pick it up with a weaker signal by changing the entry RSSI, but you still have to have a signal without much interference. In reality, that shouldn't matter too much though
WiMAX_Exit_CINR(dB) - Default is 2. See the entry CINR value for an explanation of it. If the signal degrades to a CINR of 2, it will drop the connection. Change this to 1. This should let you stay connected longer. If you run into problems with staying connected but having an unreliable connection, change it back to 2.
WiMAX_Exit_Delay(s) - The default is 2. Since it's measured in seconds, that means if the CINR drops to 2 or below for 2 seconds, it will drop the connection. Raise it to 5. That should be enough to cover just a random drop in signal that will pick back up right away. That way you don't drop connection if you drive under a bridge or something (I'm rocking mine at 15s here, but it'll take any value up to 600 seconds, which is 10 minutes!)
That should be it. I think I explained everything good enough. Let me know if you have any questions & I'll edit the OP. None of these should harm your device, but as usual heres the disclaimer: If you screw up and blame me, I will point and laugh.
I'm not in 4G ATM so I can't test it, but all the principles check out in theory. The only one that cause any 4G instability (ie having signal but not being able to transfer data) is the exit CINR. A value of 1 may be too low to transfer data, but I'm not sure. If you have that issue, just raise it back to 2. The rest will just make it pick up signal sooner.
Let me know how it works
EDIT: Also, if you follow this guide it'll let you reconnect sooner if you for some reason disconnect randomly. Plus it'll let you connect as soon as it picks up signal too, not 5 minutes after you first pick it up!
I've had people report to me on Twitter that this DRASTICALLY improves things for them. @cynicaloptimist said he used to get 4G a half mile from is house, and now he can get it 150 feet away. It may not seem like a lot, but a half mile more coverage is a helluva lot more when a tower (4G towers may vary, CDMA/EvDo figures here) may cover 10-12 miles.

Great work man, i just wish i could use it. Damn you Sprint for not having 4G in Long Island New York yet! All the hype for this phone and its flagship feature, 4G when you buy it and you find out, you cant even use it... smh.

That works great! Also, has anyone found out why it keeps searching for 4G when we turn it off? ALL evos are affected. Do a Logcat after you turn 4g off and watch it go crazy every 2 seconds. I think this issue has been seriously overlooked.

zeuzinn said:
That works great! Also, has anyone found out why it keeps searching for 4G when we turn it off? ALL evos are affected. Do a Logcat after you turn 4g off and watch it go crazy every 2 seconds. I think this issue has been seriously overlooked.
Click to expand...
Click to collapse
Yeah I've noticed that but I have no idea what may be causing it. I'll look into it, but the gist of it is, it seems to be looking for the 4G daemon running on the device, but it's been shut down already. Could be wrong tho.

inputing ##DATA# does nothing for my evo

humor...intrigue...practical knowledge...this post has it all! two thumbs up!

epst edit password
I would love to try this but I can not get pass the password on edit on ##data#. How do I get this password? Thanks

Geniusdog254 said:
[*]WiMAX_Entry_CINR(dB) - Default is 4. This is the Carrier to Interface Noise Ratio. The higher it is, the clearer the connection has to be to connect. Change it to 3. You may be able to push it all the way down to 2, but that is probably pushing it.
Click to expand...
Click to collapse
The acceptable range of values for the Evo is 4-10. The Evo just wont let me set it lower.

This was just what I was looking for, screwed up my epst.apk though so I hope I can just swap it back in with adb.

the "WiMAX_Entry_CINR(dB)" does not allow me to enter a value of 3. It says it's restricted values are between 4 - 10.
Edit: pwabbit also posted it. I guess I can confirm that he's not the only one unable to change that value.

regulator207 said:
the "WiMAX_Entry_CINR(dB)" does not allow me to enter a value of 3. It says it's restricted values are between 4 - 10.
Edit: pwabbit also posted it. I guess I can confirm that he's not the only one unable to change that value.
Click to expand...
Click to collapse
pwabbit said:
The acceptable range of values for the Evo is 4-10. The Evo just wont let me set it lower.
Click to expand...
Click to collapse
Thanks for the heads up guys. Updated the OP, sorry about that.
Everything else will still have an effect & pick up at lower signal, you just still have to have a clear signal

inputing ##DATA# does nothing for my evo
Click to expand...
Click to collapse
Run logcat while inputing the code. You will likely see msgs that indicate the phone is trying to load a number of java classes and a reason for the failure. When I had this problem it was because I had a corrupted hosts file and the phone was failing to resolve th name localhost which is the name used to call the java classes needed to load the tool.
.....
Frank...

pongoface said:
I would love to try this but I can not get pass the password on edit on ##data#. How do I get this password? Thanks
Click to expand...
Click to collapse
Call Sprint and ask for your msl or use cdma workshop to get it. Search the forum for info on cdma. There are a number of threads on the subject.
.......
Frank...

bone headz
frankenstein\ said:
Call Sprint and ask for your msl or use cdma workshop to get it. Search the forum for info on cdma. There are a number of threads on the subject.
.......
Frank...
Click to expand...
Click to collapse
Silly noobz, its ##data## you didn't add the last #

Goonzy said:
Silly noobz, its ##data## you didn't add the last #
Click to expand...
Click to collapse
Umm please tell me that was sarcasm? It's definitely ##data#
Lol I'm gunna assume it was tho

Geniusdog254 said:
Umm please tell me that was sarcasm? It's definitely ##data#
Lol I'm gunna assume it was tho
Click to expand...
Click to collapse
Nope,... its##data## for sure. I did it like that it does nothing. Seriously. Been going this for a min bro. Anyways the edits work. The sleep was also edited to 300 mins. Bty in vegas i broke the 5 mbps max i was gettin. 7.8 mbps *****es.

Goonzy said:
Nope,... its##data## for sure. I did it like that it does nothing. Seriously. Been going this for a min bro. Anyways the edits work. The sleep was also edited to 300 mins. Bty in vegas i broke the 5 mbps max i was gettin. 7.8 mbps *****es.
Click to expand...
Click to collapse
Awesome speeds. The network has just been live here in STL for about a month, started off never breaking 2.5Mbps. Now they've improved it quite a bit coverage wise & I get ~5mbps going 75MPH down I-55. I imagine it'd be better stationary.
And thats really weird. What ROM are you running? Are you using the stock HTC dialer? It should definitely be ##data# unless you're not on the HTC dialer. AAMOF it won't even let you enter the second one, as soon as you type the first it goes straight into EPST.

Lol, yeah the 4th # is silent.
Sent from my PC36100 using XDA App

Geniusdog254 said:
Awesome speeds. The network has just been live here in STL for about a month, started off never breaking 2.5Mbps. Now they've improved it quite a bit coverage wise & I get ~5mbps going 75MPH down I-55. I imagine it'd be better stationary.
And thats really weird. What ROM are you running? Are you using the stock HTC dialer? It should definitely be ##data# unless you're not on the HTC dialer. AAMOF it won't even let you enter the second one, as soon as you type the first it goes straight into EPST.
Click to expand...
Click to collapse
Yeah crazy speeds, i took a dump on myself when i hit that marker. I also have a head set plugged in with it snipped to half a inch of wire. For some odd reason i broke the barrier. With it plugged in. I think the 4g antenna is a small one compaired to the usb one. Iam using damage control 3.2.3 with the toast fps kernel and stock dialer. Great battery with dc profile set to performance and underclocked to 806 using the juice control not setcpu. When u got dc set to performance means its allowing more threads in the cpu not making it set to a full load. Just sayin.

pongoface said:
I would love to try this but I can not get pass the password on edit on ##data#. How do I get this password? Thanks
Click to expand...
Click to collapse
call sprint or cdma workshop or if you were to activate a phone on sprint.com then wait like 5 min activate the evo back the one time code or secondary code can be used as the msl pw. i have never seen anyone post that about activating the phone to get the msl. that to me would be the easiest

Better 4G Speeds?

Is it possible to edit the build.prop file like the on the Inspire 4G to achieve better speeds?

Lol this should be in general... And inspire? This is the infuse forums
Sent from my SAMSUNG-SGH-I997 using XDA App

hoofadoo said:
Lol this should be in general... And inspire? This is the infuse forums
Sent from my SAMSUNG-SGH-I997 using XDA App
Click to expand...
Click to collapse
He said "like" on the inspire...
Sent from my SAMSUNG-SGH-I997 using XDA Premium App

jeffrsho said:
He said "like" on the inspire...
Sent from my SAMSUNG-SGH-I997 using XDA Premium App
Click to expand...
Click to collapse
actually, he said, "like the on". LOL!

camoto said:
actually, he said, "like the on". LOL!
Click to expand...
Click to collapse
My bad... It still should be in general
Sent from my SAMSUNG-SGH-I997 using XDA App

I apologize if I put it in the wrong forum, but I didn't think that editing the build.prop file or regulating 4G speeds that AT&T hasn't "given" us access to yet was a general question.
Aside from that, is it possible?

Jonathon1710 said:
I apologize if I put it in the wrong forum, but I didn't think that editing the build.prop file or regulating 4G speeds that AT&T hasn't "given" us access to yet was a general question.
Aside from that, is it possible?
Click to expand...
Click to collapse
NeoS2007 said:
So, you want to post in development? Ask yourself this:
Is what I am going to post a question?
If so, this is not the right place to post a new thread. Instead, use the SEARCH function to find a thread about your question. If that's not available, post your question in General.
Click to expand...
Click to collapse
Just sayin...

Point taken.

Well no offense to anyone, but changing the build.prop of any phone to alter the dynamics of how to phone runs or behaves sounds like development to me...
Can it be done? Do you know how exactly it's done on the inspire?
Sent from my Samsung Infuse 4G

SSJ_Gomike said:
Well no offense to anyone, but changing the build.prop of any phone to alter the dynamics of how to phone runs or behaves sounds like development to me...
Can it be done? Do you know how exactly it's done on the inspire?
Sent from my Samsung Infuse 4G
Click to expand...
Click to collapse
Your missing what the dev section is for.
If someone had a custom Build.prop they wanted to share, that is a Dev post. Asking a question about development is not.

no, from what I've been tinkering with in the test settings (accessed with *#0011#) and pressing menu, back, selecting "network control", then "hspa cat control", I'm able to get better speeds on CAT 10 than CAT 14, but other's speeds may vary. (I know I'm a heavy user that uses over 15 to 20 GB per month too, so it may just be going through a CAT that I'm not throttled on too.... )
But with all above, I agree that this should be in General....

the inspire has hsupa disabled foe the att version with a line in build.prop. hsupa has been disabled on all att phone cept the iphone and the infuse. tere have been different meathods to disable it but is irrelevant because the infuse has it enabled. ther may be other settings to change but not to get even better speeds but I don't think it will be in build.prop or yield the same results.

bedwa said:
no, from what I've been tinkering with in the test settings (accessed with *#0011#) and pressing menu, back, selecting "network control", then "hspa cat control", I'm able to get better speeds on CAT 10 than CAT 14, but other's speeds may vary. (I know I'm a heavy user that uses over 15 to 20 GB per month too, so it may just be going through a CAT that I'm not throttled on too.... )
But with all above, I agree that this should be in General....
Click to expand...
Click to collapse
wow i started messing with the diffrent CAT settings on my infuse and now i have gotten up to 5250 down on my speed test! before the most ive gotten was low 3000's. a friend of mine has a infuse 4g also but he has gotten up to 10,000 down! he usually averages 7-8k on speed tests. WHY????? he has had his phone since it came out i think.

Someone needs to build a CAT setting tester/optimizer!

bedwa said:
no, from what I've been tinkering with in the test settings (accessed with *#0011#) and pressing menu, back, selecting "network control", then "hspa cat control", I'm able to get better speeds on CAT 10 than CAT 14, but other's speeds may vary. (I know I'm a heavy user that uses over 15 to 20 GB per month too, so it may just be going through a CAT that I'm not throttled on too.... )
But with all above, I agree that this should be in General....
Click to expand...
Click to collapse
So i just followed what you said and the first screen that comes up, the general service mode screen says im running on 3g even though up in my task bar it shows the H+ symbol. Has my infuse been lying to me this whole time?

pr0necr0 said:
So i just followed what you said and the first screen that comes up, the general service mode screen says im running on 3g even though up in my task bar it shows the H+ symbol. Has my infuse been lying to me this whole time?
Click to expand...
Click to collapse
No, AT&T has. HSPA+ is still 3G, even though AT&T calls it 4g. They may re-brand all the user-facing stuff to say 4G, but the phone's technical information that you aren't supposed to see will refer to it by its technical term, 3G.

if its not LTE , its not 4g Sorry to burst your bubble. I truely miss Tmobile when it comes to data. I would get around 6megs down all the time on "3g". I dont even get 3 most times with at&t and the upload is such horrible ****.

Nopcodex90 said:
if its not LTE , its not 4g Sorry to burst your bubble. I truely miss Tmobile when it comes to data. I would get around 6megs down all the time on "3g". I dont even get 3 most times with at&t and the upload is such horrible ****.
Click to expand...
Click to collapse
LTE isn't 4G either, if you want to lump HSPA+ into ' it's not 4G' category. LTE currently offers nothing remotely close to the original ITU specs.
Sent from my SAMSUNG-SGH-I997 using XDA App

lalojamesliz said:
wow i started messing with the diffrent CAT settings on my infuse and now i have gotten up to 5250 down on my speed test! before the most ive gotten was low 3000's. a friend of mine has a infuse 4g also but he has gotten up to 10,000 down! he usually averages 7-8k on speed tests. WHY????? he has had his phone since it came out i think.
Click to expand...
Click to collapse
I typically get 3-4 Mbps at work/home. Last week I was about 4 miles away, got 8.9Mbps. Another day I was about 5 miles further, got 5.5 Mbps. Depends on which tower you're on.

Yeah, I've noticed that too. I switched the CAT and got improvement at my office... Now just to check at home.
I almost feel like my Captivate was faster somehow....
Sent from my SAMSUNG-SGH-I997 using XDA Premium App

just came from g2x to the sensation

It's my second one. My first was bad, this is awesome.
Review in a bit, but the season eats g2x alive ..... Gonna be my new home for a while ...
Any good tips or tricks?

smashpunks said:
It's my second one. My first was bad, this is awesome.
Review in a bit, but the season eats g2x alive ..... Gonna be my new home for a while ...
Any good tips or tricks?
Click to expand...
Click to collapse
Ditto, Had a g2x and traded it (had no issues except for minimal screen bleed. I still have another one but it's at LG for repair rma due to excessive screen bleeding) Really am loving the sensation. The G2X is faster for sure, but we shall see which is faster once we get S-off and root and a vanilla android rom Once I get my G2X back from LG I think I will switch between the 2 for a few days then the g2x will probably become my business line phone. I'm on flex pay and here is the strange thing.. with my g2x it let me forward my VM to google voice, with the sensation it doesnt. I read that flex pay customers are barred from using conditional forwarding so not sure how it worked on my g2x and not on my sensation.. smh

Topic support bump . What kind of tricks are you looking for?

pantlesspenguin said:
Topic support bump . What kind of tricks are you looking for?
Click to expand...
Click to collapse
Hmmm i know there are issues and wondering what are good fixes off the bat. Like the browser speed trick (got that, but others)? Thanks

If you happen to get that weird black box on the lock screen, place your finger where the circle would normally be and flick up. It'll unlock the phone without a battery pull (don't know if you saw my topic on that on moco).

pantlesspenguin said:
If you happen to get that weird black box on the lock screen, place your finger where the circle would normally be and flick up. It'll unlock the phone without a battery pull (don't know if you saw my topic on that on moco).
Click to expand...
Click to collapse
No i did not, thanks though. Ill remember that.. loving it so far ....

I am on my third Sensation and so far this one has been quite good. I have a G2x which I really like as well and also a Vibrant (that I thought I would always keep) and if the Sensation continues to perform flawlessly I will sell my Vibrant. There is just something about the Sensation, I really do not know what it is, but even though the G2x is faster at this point and seems smoother to me, I just keep picking up the Sensation. I hope that s off comes very quickly so we can see what this phone is really like!!!!!!!!!!!

+1
Please include me in the list..
I dont have G2X, BUT I use to have O2X which I think is similar phone, with some dimension different and signal processes only. Anyway, I ditch my O2X due to its poor design body, and its crap software UI..I'm not deny, O2X is faster compare to sensation, but I could not stand it when I hold in my hand and play with its UI...Grrrrrrr!!!!!!
+1 also dont like its bleed display!!
Love sensation!!

Hey smash, I remember you from the Vibrant forum so welcome to The new Sensation

smashpunks said:
Hmmm i know there are issues and wondering what are good fixes off the bat. Like the browser speed trick (got that, but others)? Thanks
Click to expand...
Click to collapse
whats the browser speed trick?

graffixnyc said:
whats the browser speed trick?
Click to expand...
Click to collapse
The trick where you go to dialer press *#*#4636#*#* then toggle a few things

graffixnyc said:
whats the browser speed trick?
Click to expand...
Click to collapse
Installing Boat Browser

Anyone's browser hanging on big sites? Mine stops halfway a lot. Just factory reset, still having the issue . Is there a trick?

Anyone's browser hanging on big sites? Mine stops halfway a lot. Just factory reset, still having the issue . Is there a trick?
On WiFi...

smashpunks said:
Anyone's browser hanging on big sites? Mine stops halfway a lot. Just factory reset, still having the issue . Is there a trick?
On WiFi...
Click to expand...
Click to collapse
I had to change my APN settings, the one under mobile network were borked

jlevy73 said:
I had to change my APN settings, the one under mobile network were borked
Click to expand...
Click to collapse
How do I do that... Thanks ....
It's only hanging on WiFi...

Smash welcome to the dark side lol. And to answer your question, no I'm not having any issues loading large sites. I tried engadget (full site), cnn, and a couple others and it loads fine on or off wifi.

I'm going to jump on this thread instead of making a new one... Just returned a family member's G2x for it being the most buggy production phone I have ever seen, shame lg.
Anyway, looking at the sensation as a replacement, anything a huge issue? The g2x had such a software rebooting problem it was absolutely unusable. Just want to make sure software and hardware are working fine for most people...
Sent from my T-mobile G2

[ROM]ADT Stock AT&T Rooted Base -11|10|11:

Welcome Guys​
Ok so what we got here is a stock AT&T base for you guys to start doing somethings you want. Thanks to saywhat4118 who is the guy im using as tester and all, im taking the files from his phone!
Features
Click to expand...
Click to collapse
Code:
*Stock with all bloat
*FREE THETHERING
*Insecured kernel!
*Rooted
*Deodexed
*INIT.D folder in already, just needs a kernel with support for it! Other needed edits are done already
*Build.prop edits and Tweaks so expect ROM to feel faster plus crazy LTE speeds
*data folder support.
*Well that's about it, didn't want to touch the ROM much because i wanted it stock
Click to expand...
Click to collapse
How to flash?
*Download the ROM : HERE
*Place it in your SD card
*boot into recovery
*Wipe/factory reset
*Wipe cache
*Flash the ROM
*After done, Wipe dalvik cache
*Fix permissions
*reboot
*Please note that its recommended to let the installation sit for at least 10 minutes, and then reboot. This will aliminate any bug leaft in the flash and will definitely make the ROM run smoother! Thanks
Thanks to saywhat4118 for doing all the testes and all!

Here's a screenshot that my tester sent me> This Shows how LTE speeds are improved in this stock ROM.
My Tester used to get 20-25 inside his house, now he gets from 35-55MBPS!

Awesome! Thanks for getting this for us.

No melvin.. Thank YOU. Doubled my LTE speed. Great work, this is going to be epic.

Gr8Danes said:
Awesome! Thanks for getting this for us.
Click to expand...
Click to collapse
Im here to help bud! This is to show some love for you all!
saywhat4118 said:
No melvin.. Thank YOU. Doubled my LTE speed. Great work, this is going to be epic.
Click to expand...
Click to collapse
I dont lie my man! Told you guys what i do with network!

|Melvin| said:
Im here to help bud! This is to show some love for you all!
I dont lie my man! Told you guys what i do with network!
Click to expand...
Click to collapse
Damn......you guys are making me want to pack up and move to an LTE area. AMAZING!!

Gr8Danes said:
Damn......you guys are making me want to pack up and move to an LTE area. AMAZING!!
Click to expand...
Click to collapse
Hehe! Im jelous man! I am with T-Mobile and i only get from 8 to 14!

I guess I'm a little lucky lol. Man this speed is retarded fast.

|Melvin| said:
Hehe! Im jelous man! I am with T-Mobile and i only get from 8 to 14!
Click to expand...
Click to collapse
When I was at the AT&T store the other day, they told me that we (Minneapolis area) were half way down the list of cities. I sure hope that means by the 1st or 2nd quarter of '12. But we know them AT&T store reps...............just hoping they know what they're talking about.

Installing now. Thanks for your time and work!
Will update soon.

Gr8Danes said:
When I was at the AT&T store the other day, they told me that we (Minneapolis area) were half way down the list of cities. I sure hope that means by the 1st or 2nd quarter of '12. But we know them AT&T store reps...............just hoping they know what they're talking about.
Click to expand...
Click to collapse
Hey hey, i work for AT&T lol. not all of us there are clueless.

Hey sry but how do i fix permission? LIke what do you mean!
|Melvin| said:
Welcome Guys​
Ok so what we got here is a stock AT&T base for you guys to start doing somethings you want. Thanks to saywhat4118 who is the guy im using as tester and all, im taking the files from his phone!
How to flash?
*Download the ROM : HERE
*Place it in your SD card
*boot into recovery
*Wipe/factory reset
*Wipe cache
*Flash the ROM
*After done, Wipe dalvik cache
*Fix permissions
*reboot
*Please note that its recommended to let the installation sit for at least 10 minutes, and then reboot. This will aliminate any bug leaft in the flash and will definitely make the ROM run smoother! Thanks
Thanks to saywhat4118 for doing all the testes and all!
Click to expand...
Click to collapse

appdroid said:
Hey sry but how do i fix permission? LIke what do you mean!
Click to expand...
Click to collapse
In clockworkmod you go to advanced annd hit dalvik and then fix permissions!

saywhat4118 said:
Hey hey, i work for AT&T lol. not all of us there are clueless.
Click to expand...
Click to collapse
LOL.....I know there are good ones out there. Can you move to my local store?
Do you know if she was telling the truth? A ball park timeframe for Minneapolis to get it? (in no way holding you to it, just would be nice for an estimate).

saywhat4118 said:
Hey hey, i work for AT&T lol. not all of us there are clueless.
Click to expand...
Click to collapse
Haha...so do I. Sux I had to go to bestbuy just to get it at $149.99. At&t wouldn't even price match for employees.

Q?
Question ~ do you plan on removing carrier-IQ being as the ROM is already deodexed Melvin?

I accidentally hit fix permissions in the advanced recovery screen. Does that do anything if I didn't install anything new yet? My twitchy fingers getting in the way again..
Sent from my SAMSUNG-SGH-I727 using XDA App

|Melvin| said:
In clockworkmod you go to advanced annd hit dalvik and then fix permissions!
Click to expand...
Click to collapse
+1.
Is E:\ unknown path typical for koush's rom manager?

Gr8Danes said:
LOL.....I know there are good ones out there. Can you move to my local store?
Do you know if she was telling the truth? A ball park timeframe for Minneapolis to get it? (in no way holding you to it, just would be nice for an estimate).
Click to expand...
Click to collapse
lol its cool. To be honest, havent heard anything about Minny yet. I heard about boston, ny and couple other places. that could be because im in dallas. and trust me when i tell you this, they dont share those info with us. i have to find out on my own with my own research.
Phoneguy589 said:
Haha...so do I. Sux I had to go to bestbuy just to get it at $149.99. At&t wouldn't even price match for employees.
Click to expand...
Click to collapse
ohh that sucks. our store had a contest going, winner gets to choose between skyrocket, vivid and the iphone 4. i chose the vivid first but then switched to the skyrocket because vivids battery life wasnt that great. screen was beautiful though. so in the end, i got the skyrocket for free with unlimited lte + tethering. life is great.

My speeds
my LTE speeds outside my apt after i flashed Melvin's stock rom. before i was getting 20-30 mbs down max. now i get... well take a look at the pic.

LTE..?

This might be a point of interest.. http://www.youtube.com/watch?v=GTLEljOCpY4&feature=g-u-u

Reatret said:
This might be a point of interest.. http://www.youtube.com/watch?v=GTLEljOCpY4&feature=g-u-u
Click to expand...
Click to collapse
How is this related to HTC Sensation?
Also instead of just giving link (to get views??). It will be helpful to put some description.
Btw others looking here, this is youtube video showing LTE capability of Nexus 4.

webharsh said:
How is this related to HTC Sensation?
Also instead of just giving link (to get views??). It will be helpful to put some description.
Btw others looking here, this is youtube video showing LTE capability of Nexus 4.
Click to expand...
Click to collapse
Lol man...post it in the right forum please

Maybe the OP thinks that this could also work on sensation.
In that case, don't want to crush your dreams or anything, but that's not going to work for us..

Incanity said:
Maybe the OP thinks that this could also work on sensation.
In that case, don't want to crush your dreams or anything, but that's not going to work for us..
Click to expand...
Click to collapse
This is pretty much it since we don't have the LTE hardware...

as we dont have lte but 4g ??? on att
i have mine on att "yeah i know edge ony but wait its a lie i have 4g sometimes and want to know why or how i have screen shots too wont stay on long
dont tell me phone cant cuz it did it "a cat cant bark fact" "htc sensation went 4g on att fact"
so i dont think htc changed hardwear in phones but think they put soft some kind of lock on it for tmob can we unlock this will repost in main too