Database Info

Phone is stuck on a screen maybe bricked during flashing????

Ok I was flashing back to stock 2.1 useind odin when mid process my phone fell battery out usb disconnected and bam thats it. Now my phone is locked on a screen that shows a picture of a phone ! and a computer. I can get it back to download mode and odin will se the phone but gets no further then do not unplug device, my computer beeps when its plugged in but it dose not show the phone in my computer section. Any fixes or am i screwed?
PS phone is only two weeks old if need be could I take it back like this????

Hmm I think I may hove gotten past this problem. Uninstalled odin reinstalled and now it seems to be hopefully working

Here is the fix
I was in this same situation yesterday. Here is how to get it back into download mode.
•Be sure the Samsung USB drivers for the phone are installed on your computer.
•Remove and replace the battery.
•Connect the phone to the computer with the USB cable. The "phone-exclamation mark-computer" picture should display on the phone's screen.
•Hold the Volume Up+Volume Down+Power buttons down simultaneously.The screen should go blank, then the picture should appear again. When the screen goes blank a second time, release the Power button while continuing to hold the Volume Up+Volume Down buttons down

If that doesn't work,i had a similar problem where I could get into odin, but it would progress beyond the pit file. Take the battery, sim and memory card out of your phone. Start odin. Put the battery only back in. hold volume up and down. Plug the phone in while holding these buttons. Don't let go until you are in download mode. Now try restoring. It should work.

Thanks for the input i am back up and running!!
Sent from my SAMSUNG-SGH-I897 using XDA App

Bricked replacement Captivate - Orange Screen
Just to let you know. I recently received a replacement captivate thru warranty exchange. The phone was apparently a new one with JF6. So I decided to do an update to JH7 using Kies mini. A little over half way to the update procedure, the phone screen turned orange and stayed there for a long time, eventually I had to pull the plug. Of course I had to manually go to download mode and launch Kies mini emergency recovery, the damn thing again got stuck at the orange screen.
If anybody has this experience do no proceed further and throw that damn thing back at At&T's face. Do not attempt to do anything. I made a mistake of then doing an ODIN one-click back to stop and the phone got stuck half way, went to the orange screen.. and then it was over.. The phone was dead, wouldn't turn on, no recovery or download mode with any button combo. When I plugged in to the wall, no battery indicator.
save yourself the trouble and return the damn thing

still there
I am a "noob" to posting here, and a noob to the android due to being an avid iPhone user. I am having the same problem, phone -!- computer and have tried every method i can find in this forum to get passed it. Are there any other thoughts or suggestions? (got hung at do not turn off target in odin) Thanks in advance to any help.

I would look at this thread http://forum.xda-developers.com/showthread.php?t=1153310

Stephenv1971 said:
I would look at this thread http://forum.xda-developers.com/showthread.php?t=1153310
Click to expand...
Click to collapse
went that route, still cant find dl mode. have resistors built and all. any way i try to boot shows me the phone -!- computer, and the computer doesnt attempt to recognise it so there is no communication between the computer and phone. unfortunately, i dont have a v/ohm meter, so i am not sure of the accuracy of the resistors i used to make my jig.

I fixed this many times with phone that had the button download mode and didn't.
Getting into download mode while softbricked like this wont show the normal download screen. IT will still show the error screen....
With download mode working still:
Simply remove the battery and replace,
Open odin
Hold down volume keys and plug it in till you see odin recognize ur phone.
Then continue to use odin.
Dosent work, repeat.
If you know ur button combo dosent work:
Just open odin.
Remove battery & replace.
Use jig (3k 100k ohms twisted)
Then when the phone turns on and your see the pc! screen plug in usb.
See if odin sees it.

Assuming your flash didn't fail on the PBL.bin or SBL.bin you should be fine.
Follow the methods suggested by other users here and you will get back up and running in no time at all.

Don't sweat the 'phone-!-pc' screen. I'm a little surprised that no one has given you the good news....that is just a version of the download screen for later hardware revisions. It looks bad, but if Odin recognizes your phone (if one of the COM fields goes active), just start your flash again.
Now if Odin does not recognize the phone when plugged in via USB, then you have some more work to do.

I had forgotten about posting here, and my problem has been resolved. So here it is... I tried everything that I could find within this forum, almost. I built my own jig with inferior radio shack components that would not activate download mode, though it would turn the phone on. I got wise, spent 8 dollars at ebay and purchased a JIG there. Instant download mode after 3 days (shipping). Reflashed with one click, updated w/ kies, made kernal changes and am now rockin my captivate. Thanks to those who assisted.

Steve_O_1971 said:
I had forgotten about posting here, and my problem has been resolved. So here it is... I tried everything that I could find within this forum, almost. I built my own jig with inferior radio shack components that would not activate download mode, though it would turn the phone on. I got wise, spent 8 dollars at ebay and purchased a JIG there. Instant download mode after 3 days (shipping). Reflashed with one click, updated w/ kies, made kernal changes and am now rockin my captivate. Thanks to those who assisted.
Click to expand...
Click to collapse
Using the 3-resistor method takes A LOT of patience, at least in my experience. Glad everything worked out.

beast534 said:
Using the 3-resistor method takes A LOT of patience, at least in my experience. Glad everything worked out.
Click to expand...
Click to collapse
Patience is a virtue, and my Ex's name. LOL! I can do without patience.
Jokes aside, i actually soldered the resistors to a plug that i had cut up, and made sure it was covered so my skin wouldnt come in contact. The Radio Shack here buys inferior products and sells them at reggular retail. Unfortunately my $300.00 V-Ohm meter is on the fritz, and i have not had the time or money to replace it yet, but I have intentions to check the actual resistance of the jig I made. ^^

Partially Bricked Captivate

Hey guys, quick question. I've been scouring the forum here but haven't found a solution yet.
I was attempting to flash back to stock using Odin and my phone just kinda "hung up." Odin basically froze so I did a battery pull hoping that I'd be able to re-enter download mode and reflash to stock.
Now I'm getting a black screen with a phone, and exclamation point, and a computer icon every time i try to power on my phone.
I've tried every configuration of the 3 button combo to get back into download mode that I can think of but thus far nothing has helped.
I've read that this screen is a sign that you're only "partially bricked" but I cannot for the life of me get my phone to proceed past this screen in any way.
Can anyone help?

You need a Jig. This is how I fixed mine but they sell them on Ebay if you have the time to wait.
http://forum.xda-developers.com/showthread.php?t=841512&highlight=iGo

You try turning on odin, plug usb into computer and NOT the phone, Then while holding volume up/down plug usb into phone. That put my phone in download mode for me, it may take a few trys but hopefully you can get it to work

http://forum.xda-developers.com/showthread.php?t=775911
Follow this ^^

I've done that to my phone countless times. The first time, I was really freak out lol. I personally used this method its worked every time for me. It's difficult to get it to work the first time, but one you get the hang of it its not too bad, so don't get frustrated if you try it and it takes a few times. It's also the most cost effective. Instruction are there under the video.
http://www.youtube.com/watch?v=D0aoabVtPJ8

I appreciate the replies guys.
I was able to make my own Jig using a micro usb I had lying around and some resistors I bought this afternoon.
It's a hell of a relief to have my phone up and running and having only spent $4 to get it working again as opposed to the $125 AT&T would have charged me for the replacement.
Again, much thanks!

Totally Bricked Charge? Non-responsive

Calling all Android Superheroes!!
I think I've done it. Turned my Charge into a paperweight. Was trying to flash the latest GummyCharged 1.91 package using Odin. It failed 3 times, but having read many accounts of similar failures I retried using different cables, different ports etc. After every "Fail" I unplugged the phone, rebooted, shut down Odin and started all over again.
After the last "Fail" message the phone simply stopped responding to anything. Won't boot, won't go into download mode, won't boot to recovery, doesn't show any sign of life when plugged into the wall.
All my reading about bricked Droids all seem to have some kind of responsiveness so don't seem to apply to my situation.
If anyone has suggestions or can point me in the direction of further resources I can research I'll be most grateful.
The worst part is going to be telling the wife when she asks what I'm doing.....
Thanks in advance for any / all help.

Call verizon tech support and give them some crap about how your phone was powering off by itself and you were dropping 4g, 3g, and 1x consistently and now your phone wont even turn on. They'll surly send you a like-new replacement phone.

I was having odin problems with my Charge as well, every rom failed... I figured out I had to uncheck 'reboot' and keep the battery in to get it to flash right. I know this doesn't really help but its similar
blazing through on my VZ Droid Charge

Thanks Sleek. I bought mine through Costco so I think I've also got the option to head back to Costco and get it swapped out. However, I've made my way through life believing that I should never surrender to the challenges presented by technology nor my own stupidity, so I'm pride-bound to at least try to make lemonade out of this situation.

anoninja118 said:
I was having odin problems with my Charge as well, every rom failed... I figured out I had to uncheck 'reboot' and keep the battery in to get it to flash right. I know this doesn't really help but its similar
blazing through on my VZ Droid Charge
Click to expand...
Click to collapse
Thanks anoninja - I'll keep those tips handy for the next flash attempt. And there WILL be further attempts....

I had this happen to me on the second day I had my Charge. What happened was, I was flashing what I thought was the latest version of Humble EE4, but it wasn't, it an old .md5 file for my Epic. I didn't even look at the file name, I just looked at the file extension and it would not turn on, wouldn't show that it was charging (no pun), or any sign of life other then the phone would get hot due to something with the battery.
My solution was that I called VZ customer care and said something like, "For some reason my phone will not turn on. I plugged it last night and when I awoke this morning, it will not come on. I tried pulling the battery and it still does nothing. Is there anything you can do to help me?"
So the customer care lady tried to walk me trough a factory/data reset, and you guess it, "it didn't work." After another five minutes or so of her "trying" to help me, she said that they would replace it under the warranty and she overnight-ed me a new phone and I had it the next day. I did have to send the bricked phone back to VZ, so for good measure I ran an electromagnet over it, you know just in case.
You can try it that way or go into the carrier store and play dumb (like you really shouldn't have a smart phone) and have them replace under the warranty.
Good luck!!!

Take out battery, plug into rear usb ports (if you're on a tower. If you're on a laptop it doesn't really matter. If you want to know why just ask, otherwise just do it). Fire up Odin3 with administrative rights (right click, run as admin). Hold down the lower volume button and cross your fingers. If it still won't power up into download mode, your phone has tapped out and needs to be replaced.
Sent from my Droid Charge running Humble 1.4

Some times the phone looses power during the flashing process even though it's connected to the computer. Keep the battery in the phone while flashing to alleviate this issue.
Sent from my SCH-I510 using XDA Premium App

kvswim said:
Take out battery, plug into rear usb ports (if you're on a tower. If you're on a laptop it doesn't really matter. If you want to know why just ask, otherwise just do it). Fire up Odin3 with administrative rights (right click, run as admin). Hold down the lower volume button and cross your fingers. If it still won't power up into download mode, your phone has tapped out and needs to be replaced.
Sent from my Droid Charge running Humble 1.4
Click to expand...
Click to collapse
Do everything he says but odin recovery.tar its in the humble ee4 section. After that reboot phone go to settings, then development, and turn on usb debugging. It took me 2 days to figure this out. Did the same thing. From now on before you odin make sure usb debugging is enabled. Hope this helps.
Sent from my SCH-I510 using XDA App
Just checked that forum and realized recovery.tar is not there. If you want it just pm me and ill email it to you. Its a lifesaver in your situation.

try this;
with battery out, keep the phone unplugged and hold down the volume down button and put the battery back in (not usb cable) and see if your phone responds to download mode this way. If it does, plug the phone in and see if odin now sees your device (with the battery still in).]
This worked for me in a similar situation.

My phone got hosed so bad that Odin would error out.
I finally found this and it managed to recover my phone:
http://www.mydroidworld.com/forums/...harge-full-factory-tar-flashing-software.html

quarky42 said:
My phone got hosed so bad that Odin would error out.
I finally found this and it managed to recover my phone:
http://www.mydroidworld.com/forums/...harge-full-factory-tar-flashing-software.html
Click to expand...
Click to collapse
Same here. It totally saved my butt.

Hi all. I appreciate all the suggestions. In the end I solved my problem by exchanging the phone. I couldn't get it to come back to life no matter what I tried. Thanks again to all.
Sent from my SCH-I510 using XDA App

[Q] Infuse bootloop

Im trying to explain everything to prevent unneeded questions
I have viewed several threads about this but absolutely none with an answer. My Samsung Infuse 4g with at&t (nonrooted) is in a bootloop. The cause of this was my every-other-day reboot. Once I turned it back on it goes to the samsung screen for about 5 secs, then goes black, then says samsung again and so on repeatedly. I pull the battery and as soon as it makes contact back with the phone it turns on by itself into the same Samsung screen over and over. When plugged into wall or computer it will show the charge screen where there is no battery life left, then it will flash and start up the charge screen again and so on just like the samsung screen. I cannot go into download mode (the buttons, at this point, do nothing. No response)
I have tried taking the battery out and plugging in usb cable to computer, then holding both volumes and putting battery in=charging loop
↑ with volume up=charging loop
↑↑ with volume down=charging loop
computer doesnt detect it, adb cant find it, cannot go into download mode, odin cant see it, heimdall cant see it, cant actually boot into anything, cant leave battery in or else phone will restart itself the entire time, and this was caused by my (already gbread) infuse 4g doing a regular reboot (aka power button, tap power off, after phone is confirmed off take battery out, battery back in, turn on)
Recommendations at this point? on a scale from 1=noob to 10=expert im a 7 on this type of thing. Ive always heard that as long as you can boot into a picture its only soft bricked but if i was right i wouldnt be here. Any and all help would be much appreciated. If you need me to post a video I would have NO problem doing that showing everything im doing.

oh, and by I have viewed several threads about this i meant that i have only been able to find 1 thread about it and 2 links that didnt work for me but might for you
link that worked- http://forum.xda-developers.com/archive/index.php/t-1354731.html
links that did not-
http://www.google.com/url?sa=t&rct=...ih1Zf_BvtcIbJXGEw&sig2=jjOcukFWr9sPWJZH1rlhnA
http://www.google.com/url?sa=t&rct=...ih1Zf_BvtcIbJXGEw&sig2=SZeMzIF2hnjdkk6GPDkovg

You might have already tried this way, but I've always held down both volume buttons first before plugging in the USB cord - not the other way around. You can also try different cords, different USB ports and/or different computers.

Mine was doing this the other day and it turned out to be my SD card being flaky. Maybe try taking it out and booting?

Radiotsar said:
You might have already tried this way, but I've always held down both volume buttons first before plugging in the USB cord - not the other way around. You can also try different cords, different USB ports and/or different computers.
Click to expand...
Click to collapse
Ive tried a hp touchpad cord, an atrix cord, and the original cord. I cant really do the button combo because as soon as the battery makes contact the phone turns on. thats why i had the usb cord in first to see if it worked. ive tried every usb port and 2 different laptops, the computer wont recognize it if the phone wont go past the samsung start up screen
J101 said:
Mine was doing this the other day and it turned out to be my SD card being flaky. Maybe try taking it out and booting?
Click to expand...
Click to collapse
I've taken the card out and used a different card, nothing. Tried taking sim card out, nothing.

I should have been clearer. Leave the battery out of the process until after attaching the cord and the screen coming up.
Sent from my SGH-I997 using xda premium

Radiotsar said:
I should have been clearer. Leave the battery out of the process until after attaching the cord and the screen coming up.
Sent from my SGH-I997 using xda premium
Click to expand...
Click to collapse
I do, every time.
1. battery out
2. hold down volume buttons (any combo)
3. attach cord (nothing happens, no screen, nothing)
4. put battery in
Results= Charging loop

lifetaker said:
I do, every time.
1. battery out
2. hold down volume buttons (any combo)
3. attach cord (nothing happens, no screen, nothing)
4. put battery in
Results= Charging loop
Click to expand...
Click to collapse
should be the same...wonder if you battery needs to be charged first, it should be fully charged at best...to do any flash/Odin/one click
this how I do it...basicly the same..
>take batt out
>plug in usb cable...to both phone and computer
>hold both volume buttons...NO NOT HOLD THE POWER BUTTON....
>put batt in...
and bam should see the android dude shoveling in yellow triangle...

If you get no response from the usb without the battery, and inserting the battery indicates the battery needs charging - I'd suspect the phone's usb port. Especially after trying different cords & computers.
Sent from my SGH-I997 using xda premium

Sorry for the sometimes choppy video recording.
http://www.youtube.com/watch?v=QWKdGS_5_Ps&feature=youtu.be

Have you tried a jig you can buy them on ebay for 6-12 bucks or you can donate one of you old cables and make it your self..
http://galaxys2root.com/galaxy-s2-hacks/how-to-make-a-usb-jig-for-your-galaxy-s2/
this will/should get you into download mode

Hello.
I have the same problem... tried also everything now i gave it to cellphone shop, i hope you guys can give me answer before i am gonna waist $100

HELP?1
Help me please

I was in this state. There are two options I can think of. A JIG as mentioned previously or the Heimdall One-Click-Unbrick. The one-click unbrick did it for me and got me back to cmw and download mode, then i could flash to stock, root and flash up to ICS. It was really easy and I stopped sweating once it booted to cmw instantly after running it.
Joe

hello.
The problem is when i connect it to my computer its keep disconnecting and doing terreble noise, (windows noise) when you keep connecting and disconnecting USB cable
JIG DIDNT WORK, because the same problem.... maybe the chargging connect is broken? or has a corrosion?

Please use the Q&A Forum for questions &
Read the Forum Rules Ref Posting
Thanks ✟
Moving to Q&A

Sounds/Looks like a hardware issue...
Did it get any water damage in the past?
Hope you got warranty or still under warranty.

I am having exactly the same problem. My Infuse has never been rooted or unlocked (quite ironically, I was about to root it for the first time).
Boot loop when not plugged in, charge loop when plugged in. Absolutely no combination of buttons, inserting/removing the battery, and/or plugging/unplugging the USB has gotten it to do anything.
This has happened several times over the past few days. The first few times it sorted itself out in an hour or two. Today I couldn't get it to do anything at all.
I found several posts by people who have this problem, and it has never been conclusively solved from what I've seen. Finally one person said they fixed it by lightly smacking the phone with their hand. Lo and behold, it came on for about 5 minutes before looping again. So I smacked it again, and before it could re-loop, I factory reset it. A few hours went by and I was convinced that it was fixed.
A few minutes ago I had it plugged in to my computer via USB and was getting ready to SuperOneClick it. Then it went back into loop. I can't get it to come on this time. Again, no combination of buttons will send it into download mode. The computer can't see it. The battery is charged. The USB cable and port are fine. The software was reset earlier today. Does this mean that I have a hardware problem, or is there a software issue that could be fixable?
EDIT: So I decided to try hitting the power button, something that had never worked to this point, and the device came on. A couple minutes later it went back to boot loop. On a whim I tried download mode, which had stubbornly refused to work all day. Of course it immediately worked. Not really knowing what to try, since I'd already wiped user data, I wiped cache data and formatted the internal SD. Then I told it to reboot. Back to boot loop. A few minutes later, it came back on with the power button. Two minutes later, boot loop again. Then it restarted of its own accord. And now back to boot loop. I just don't even know anymore.
EDIT2: Just a thought... Something is weird with the power button. Whenever the phone is on and I hit power (briefly, not holding it down), it goes to the shutdown menu as though I'd held it down. A few seconds later, I'm always back in boot loop.

Infuse loop
I have found the problem. It is, in my case, the power button. I removed the case and crossed terminals with a paperclip. BAM. Booted up, and when I removed the paper clip.... back to boot loop at Samsung logo.
There is a place to send the phone. Ive see great reviews.
mobiletechvideos.mybigcommerce.com/samsung-infuse-4g-power-button-repair/

Seems like there has been a string of power button malfunctions going around lately. There are a few threads going on where people have had this issue. Sometimes its just the terminals needing to be cleaned or dust blown out.

Phone wont power on, heard of a program that might help, but dont know the name.

Like to start off saying hello, great to be here great amounts of information.
I Have me a Huawei U8800-51 (Impulse 4G).
I Just got the one used. Rooted it, and got around to working on it to get Gingerbread on it. It all worked out great.
It worked fine for 3 Days suddenly i decide to reboot it. it shut off but never came back on. Battery was fully charged.
Removing battery for an hour solved nothing. Attempting to go into debug (Vol + & - with power held down) or CW (Vol + With Power held down) resulted in nothing. The phone always when off would turn on display battery charging when connected to power. no this dose not happen.
I still think the phone is drawing power from the battery in this state because the phone would get a little worm like normal.
I talked to someone that ran into a similar issue with a different phone he once had. He Spoke that he had to download a program which was posted about on XDA, which allowed him to power on the phone by forcing the ports open when plugged into USB.
Thing is, he cant remember the name. So I hope for a little help with this. right now im stone broke so i cant afford to buy any mod cables. like JIGs or anything. If a certain cable is needed whats with the cable that makes it different? (If i have too ill rip bits from other old electronics to find a match and attach it to a old spare cable.
I think the problem with the one is related to the changes i made and something must of been buggy.
Even know i got the phone cheap and used. i hate to just ended up with a $120 Paperweight.
Worked all like new when i got it, nothing wrong with it, not even a mark on it.
Feel free to give me a answer even if you have to have Linux to do it. i got both Windows and Linux on my system.
Thanks in advance.