hi, im a new user and i have a problem connecting my spv c600 to my pc(windows xp)via usb. every time i try to connect my device the pc detects at first but then says"a problem occurred during installation your new hardware might not work properly" i have activesync 4.5 installed but it does not detect. i was wondering if there is a free driver i could download to sort this problem .please i need your help because i want to upgrade the rom
Windows Mobile devices are connected either via RNDIS or Serial over USB. Usually the decice is in the mode to connect over RNDIS, but when the drivers are missing on the PC they must be installed there. Look for generic RNDIS drivers on windows XP. You could also try to switch the device to Serial over USB mode. This hides in a something like "enhanced functionality" on the USB connection. On is "RNDIS" while off is "Serial" mode.
where can this "enhanced functionality" be found, on the device or on the pc, please guide me i'm kind of new on this things
It is on the phone, probably somewhere in the settings menu. No clue about the menu on your phone as I use a cooked WM6 ROM. Possibly it is even only hidden in the registry somewhere. You will have to search XDA for this a little yourself - I cannot guide you through this.
thanx for yor help
Related
Hi
Thank you for reading my post.
I do not know why, but active synch does not detect my Samsung i780. Even windows shows that a SGH-i780 is detected but nothing from the ActiveSyc side.
I installed Samsung USB driver and Active Syc 4.5, My windows is XP SP2 and all anti virus and firewalls are disabled.
Any advice is appreciated.
Thanks.
j
check active sync settings .
kindly try the following steps:
1. restart your phone
2. remove all usb devices (portable hdd, flash drives, etc.)
3. connect the cable first to your phone then to your pc.
if this doesnt work try reinstalling activesyc or check your cable.
i have experienced also this kind of of problem when usb devices are connected specially storage devices.
hope this one works
hallo
i had also the same problem..but now the problem is gone, try to uncheck the box in Connection---> USB to PC--> activation advandce networkfunktion. and then restart your pc and disconnect und reconnect your phone to your PC
hope it will work.
ps. sorry for my bad english
kindly install Microsoft ActiveSync 4.5 to your pc if your phone still not detect or regonize by windows even already install samsung modem driver.it works for me.
This must have been covered before but search does not seem to be working for me here.
I want to access the mem card in my Fuze (stock ROM) on my work PC but it needs to load a driver for the new USB device it detects. I do NOT want to install ActiveSync on the machine, only the driver that will allow the USB connection to work in Disk Drive mode.
Anyone know what file and where I could find it would allow this connection to work?
Installing applications is prohibited by company policy and installing ActiveSync would be detected. Installing a USB driver would not be.
Anyone?
the_nite_owl said:
This must have been covered before but search does not seem to be working for me here.
I want to access the mem card in my Fuze (stock ROM) on my work PC but it needs to load a driver for the new USB device it detects. I do NOT want to install ActiveSync on the machine, only the driver that will allow the USB connection to work in Disk Drive mode.
Anyone know what file and where I could find it would allow this connection to work?
Installing applications is prohibited by company policy and installing ActiveSync would be detected. Installing a USB driver would not be.
Anyone?
Click to expand...
Click to collapse
What OS are you using? Windows 2000 and definitely XP and Vista are plug and play. I'm using XP and the driver is here:
c:\Windows\system32\drivers\USBSTOR.SYS
If that driver isn't on your system, have you tried using the "Found New Hardware" wizard to connect to microsoft to automatically download the driver for you?
LBchinksTA said:
What OS are you using? Windows 2000 and definitely XP and Vista are plug and play. I'm using XP and the driver is here:
c:\Windows\system32\drivers\USBSTOR.SYS
If that driver isn't on your system, have you tried using the "Found New Hardware" wizard to connect to microsoft to automatically download the driver for you?
Click to expand...
Click to collapse
XP. The driver is not found by the wizard. I have had this on other systems before.
It is installed during the ActiveSync install. If you uninstall ActiveSync the driver is left behind and will still function but corporate policy has gotten strict on unapproved installs and traces are always left behind even after uninstall.
I will look on my home device for the file and see if I can move it to my work PC and get it working.
Thanks.
I am stuck in bootloader mode after trying to update to tomal mobile 6.
The screen on Imate jasjar says USB at the top and V 1.01 at the bottom.
The mobile device center does not allow USB since I checked it off.
When I execute MTTY1.42 usb is not given as an option.
When I execute MTTY 0.01 I get USB as an option However when I click on it I get the message "USB port cannot open"
By the way my screen says serial originally and then USB when I connect to my usb port.
I assume that if my screen says either serial or usb that it is in boot loader mode.
This is the second time that I had this problem after trying to update using Ranju's mobile 6 upgrade.
However the first time I was able to recover by starting with the MTTY 1.42 execution
Mobile device center suggests Vista. Most people would not dare these things without using XP. Suggest you do the same and disable activesync USB connection option before using MTTY
that is my next move. Go tto a computer with XP. although I was able to execute MTTY before this on my 64 bit vista computer.
Both my home computers run Vista 32 or 64.
Could there be a physical connection problem with my USB even if serial changes to USB when I plug my device into the USB port?
It is like I have apart USB connection but not complete. Or is there a software problem in the device with the part that handles the USB port? If so is there a way out?
If your device changes from serial to usb then you can start the upgrade... 8.5 seems to be the best so for with my experience..
Are you aware that I have a non background lit screen? That the device charge light does not come on? That it does not respond to soft reset?
It only reacts to hard reset and to the insertion of the USB cable?
When I try to run MTTY which I thought that I was supposed to to clear something I get the message that it cannot find a USB port.
Given this state can I do the upgrade that you suggested? or are you assuming that my imate jasjar is fully functioning
what do you mean by .......8.5 upgrade
Okay thats sounds good so far, i have been researching about that problem you have. when the serial changes to USB thats good, it means you are ready to run the update just ignore the recognition of the usb pop up message. did you down load the 8,5 Tomal's? if so run it i will do the same this side, i have been testing the 8.71 it tereble do not use it Tomal must try to put some time on it because he forgot some of impotant features. if the device shows usb then no need for MTTY. you just run the update rom. let us know what happens. Its normal that the back light is of just upgrade. Here is the link for the 8.5 upgrade screen shots; http://forum.xda-developers.com/showthread.php?t=454906 The download link; http://vidmes.com/xda/Uni/ROMs/Tomal...WM61_20764.exe
Looks like the download link will not work just scroll down on this link and download the special build rom. (window Mobile 6.1 V8.5 Tomal) http://forum.xda-developers.com/showthread.php?t=454906
Is your memory card slot in use? Remove memory card prior to using mtty or boot loader mode.
Yes the storage card is out
the sim card is out
the device is connected to the pc
the screen on the device shows USB
I run tomal version 8.5
I get the message
error CEROM update error
then I follow the recovery instructions
on recovery I get
RUU has stopped working
eroor 101 connection error
note
someone says
"U must remove the Memory card b4 upgrade, (Very impotant)"
Does that make sense
My problems started with
I had the crossbow Mobile on the system before.
I did a system restore
then tried install tomal 8.5
and from there things went off the cliff
I am now going to try things on a XP loaded computer as a last resort
swiching to my office computer and with active sync I was able to install TOML 8.5
Problem was with vista apparently
Mtty Help me Please..
Guys,
Please help me, every time I try to use mtty, it always like this attachment. What should I do, I allready follow the instruction, but still the same.
I would try on an XP computer
I did it on XP computer.
orb3000 said:
I would try on an XP computer
Click to expand...
Click to collapse
make sure your usb port in uni is not brocken. is active sync can running well?
have you un-check "allow usb connection" in connection setting before running mtty?
When I use activesynv v 4.5 it can connect correctly. Before use Mtty, already uncheck "allow usb connection". And the result is still the same. What's wrong?
indrastrid said:
make sure your usb port in uni is not brocken. is active sync can running well?
have you un-check "allow usb connection" in connection setting before running mtty?
Click to expand...
Click to collapse
irmanpribadi said:
When I use activesynv v 4.5 it can connect correctly. Before use Mtty, already uncheck "allow usb connection". And the result is still the same. What's wrong?
Click to expand...
Click to collapse
Now, there are only two things...
1. USB Sync driver in your PC is not functioning correctly
2. You have physical problem in USB port at your device
just my two cents.
irmanpribadi said:
When I use activesynv v 4.5 it can connect correctly. Before use Mtty, already uncheck "allow usb connection". And the result is still the same. What's wrong?
Click to expand...
Click to collapse
set your uni in bootloader i.e. press power button + backlight and reset using your stylus.
make sure you have disabled USB connections in AS
my two cents
So i got this error with a big "X" inside this red circle and next to it just says the word "Error" then nothing else when i tried sync using WMDC thats what happens. Btw im using a HTC Touch Pro and i tried plenty of solution from the Microsoft website this includes the following:
-Uninstalling the device driver and reconnect the device
-Disabling Advance Network Functionality
-Disabling firewall, antivirus software etc.
-Running WMDC on compatability mode
-Soft resetting device
-Hard resetting device
-Flashing a new ROM
Thanks in advance
[email protected]
[email protected] said:
So i got this error with a big "X" inside this red circle and next to it just says the word "Error" then nothing else when i tried sync using WMDC thats what happens. Btw im using a HTC Touch Pro and i tried plenty of solution from the Microsoft website this includes the following:
-Uninstalling the device driver and reconnect the device
-Disabling Advance Network Functionality
-Disabling firewall, antivirus software etc.
-Running WMDC on compatability mode
-Soft resetting device
-Hard resetting device
-Flashing a new ROM
Thanks in advance
[email protected]
Click to expand...
Click to collapse
what os?
try a new cable, or try plugging the cable into a different usb port.
i got the same problem. my pc:
Windows 7 with windows device center.
can not recognise my device.
i plug in the touch pro. i get the message to choos active sync diskdrive or share my internet.
i choose active sync.
then nothing happens in device center.
tried uninstalling rndis. after restart it installes the phone again and then it works for 1 time only. after that its the same.
i have searched forums saying that uninstalling device center does not solve the problem. also they say downloading the version on the MC site is another version that Windows 7 is shipped with.
Need help, wanna install another rom. i do have another pc, but i wished it would work on this pc.
any help would be very appreciated.
EDIT 24-10-2009
Also got this message at the properties of Microsoft Windows Mobile Remote Adapter:
This device is not working properly because Windows cannot load the drivers required for this device. (Code 31)
Hope that this could help me in some way
wishmaster86 said:
i got the same problem. my pc:
Windows 7 with windows device center.
can not recognise my device.
i plug in the touch pro. i get the message to choos active sync diskdrive or share my internet.
i choose active sync.
then nothing happens in device center.
tried uninstalling rndis. after restart it installes the phone again and then it works for 1 time only. after that its the same.
i have searched forums saying that uninstalling device center does not solve the problem. also they say downloading the version on the MC site is another version that Windows 7 is shipped with.
Need help, wanna install another rom. i do have another pc, but i wished it would work on this pc.
any help would be very appreciated.
EDIT 24-10-2009
Also got this message at the properties of Microsoft Windows Mobile Remote Adapter:
This device is not working properly because Windows cannot load the drivers required for this device. (Code 31)
Hope that this could help me in some way
Click to expand...
Click to collapse
You could just update to the latest HTC ROM from the official website if your phone is still under warranty, btw thats what i did but it didn't help. Note, that i'm running Windows 7 as my OS if anyone want to know this information to help solve the problem. Thanks in advance.
[email protected]
wishmaster86 said:
i got the same problem. my pc:
Windows 7 with windows device center.
can not recognise my device.
i plug in the touch pro. i get the message to choos active sync diskdrive or share my internet.
i choose active sync.
then nothing happens in device center.
tried uninstalling rndis. after restart it installes the phone again and then it works for 1 time only. after that its the same.
i have searched forums saying that uninstalling device center does not solve the problem. also they say downloading the version on the MC site is another version that Windows 7 is shipped with.
Need help, wanna install another rom. i do have another pc, but i wished it would work on this pc.
any help would be very appreciated.
EDIT 24-10-2009
Also got this message at the properties of Microsoft Windows Mobile Remote Adapter:
This device is not working properly because Windows cannot load the drivers required for this device. (Code 31)
Hope that this could help me in some way
Click to expand...
Click to collapse
Settings-->Connections-->USB to PC and Uncheck Enable faster data Synchronization
I have the same problem.
in my situation i tried to recover usb-flash and flash a nokia phone. For both things programs installed their own drivers. Even after I deinstalled the software I probably still have their drivers on my pc. That's why I can't sync my phone...
is there a tool to manage installed drivers?
or the other way out is to reinstall windows 7
anyone willing to help?
This solution worked for me:
Thanks to Scubamike
copy and paste from
http://social.microsoft.com/Forums/...c/thread/7a6516e2-9a46-4e1f-b689-1aa7dc2bda64
I found a different solution that worked for me: On my phone I clicked start/programs/active sync/options and deleted all the old PC connections that were displayed. In fact, you could probably just delete ALL the PC connections displayed and start from scratch. You'll just have set up another sync partnership in WMDC when you plug it in. Let me know if this helps.
it is to easy! should work ALWAYS:
Make sure "Advanced network functionality" is switched off in the USB to PC settings then:
go to activesync, menu, connections, disable "connect via USB" off, press "ok" go back to connections, enable "connect via usb" press "ok" unplug and replug your cable. and all works.
greetings
i had trouble with a 6.5.3 rom i just cooked. had to uninstall, reboot, reinstall wmdc, then i synced okay.
I have the last original rom and win 7 and with removing all remembered connections on the pda, it connected immidiatly. Thank you for the help
i have been all over the microsoft forums to no avail. i recently updated my laptop to win7, and have a fuze running 6.1 mobile. when i connect my fuze to the laptop the laptop recognizes it as it begins to charge, but then nothing. i try to open win mobile device center and this is the error message i get C:\windows\system32\rapistub.dll is either not designed to run on windows or it contains errors. I have uninstalled and reinstalled 3 times and also tried different usb ports on my laptop. If anyone can help that would be awesome
Hi All!
I've just changed from Window XP to Window 7
Unfotunately...
activesync is not working on Window 7 anymore...
I've install WMDC for Window 7 ,64 bit
but after the installation, and i plug in my phone,
a process for searching the driver loads for a while
and said: driver not found
The WMDC has no response when i plug my phone in.
I have tried different methods that i can search on the web:
1) remove device+uninstall WMDC + reboot + plugin and install WMDC again
2) disable the advance network function
but no luck...
I can connect my phone as a "USB drive", but what i want to do is to let my phone surf the internet through the PC... so I need something like active sync... can anyone suggest other alternatives which can fulfil my needs...or can anyone give me some tips on how to connect my phone to WMDC>.<
Really need help...SOS...
I encountered the same problem going from XP to 64bit Win7. I manage to solve the problem.
1. WMDC is not installed as a default during Win7 install. It is installed via Windows Update.
2. After this, WMDC will come on if u plug in the PDA but gives u an Error after trying to connect to the PDA for a while
3. Here's the solution. Go to COntrol Panel/Device Manager. Open up the list of devices installed. Plug in your pda and notice a new device is listed as "Unknown device" appears under the Device manager tree.
4. Click properties of this unknown device and choose to upgrade the driver. You will need internet connection for Windows Update to download the device driver. This driver is about 11.9MB file size.
5. After download, re-connect the PDA and it should recognize the PDA immediately.
I also noticed that if I plug in another PDA model, it will also connect and work.
Hope this helps.
I have do the same many times ...but still no luck...
what is your phone model?
I have sent an mail to Asus, ans it said there are no driver for window 7 64 bits for my phone model..... only have 32 bits...